气固脉冲流化床的流体力学特性

在直径７０ｍｍ的流化床中,采用ＦＣＣ、空心玻璃珠、细沙等Ａ类和Ｂ类颗粒,在０￣１０Ｈｚ的频率范围内,测定了气固脉冲流化床的流体力学特性。采用时间继电器改变脉冲气流的频率和脉宽周期比,利用微压传感器记录床层压力变化,研究了瞬时床层压力、平均床层压力,最大床层压降、起始流化速度、床层高度等随操作条件的变化规律,并对脉冲流化床中的气泡现象进行了初步的观察和研究,发现在脉冲流化床中气泡的形成和发展受到了有     

A Practical Method to Estimate the Bed Height of a Fluidized Bed of Fine Particles

Knowledge of both dense bed expansion and freeboard solids inventory are required for the determination of bed height in fluidized beds of fine particles, e.g., Fluidized Catalytic Cracking (FCC) catalysts. A more accurate estimation of the solids inventory in the freeboard is achieved based on a modified model for the freeboard particle concentration profile. Using the experimentally determined dense bed expansion and the modified freeboard model, a more practical method with improved accuracy is provided to determine the bed height both in laboratory and industrial fluidized beds of FCC particles. The bed height in a fluidized bed can exhibit different trends as the superficial gas velocity increases, depending on the different characteristics of the dense bed expansion and solids entrainment in the freeboard. The factors that influence the bed height are discussed, showing the complexity of bed height and demonstrating that it is not realistic to determine the bed height by a generalized model that can accurately predict the dense bed expansion and freeboard solids inventory simultaneously. Moreover, a method to determine the bed height, based on axial pressure fluctuation profiles, is proposed in this study for laboratory fluidized beds, which provides improved accuracy compared to observation alone or determining the turning points in the axial pressure profiles, especially in high‐velocity fluidized beds.     

干法造粒炉黑臭氧氧化流化床技术的开发(Ⅱ)热态间歇反应

在热态间歇状态下,考察气流速度、臭氧浓度、反应温度、干法炉黑静床高度及干法炉黑在流化床内的反应时间等因素对干法炉黑臭氧氧化深度即炉黑ｐＨ值的影响,以确定适宜的干法炉黑臭氧氧化的工艺条件．上述因素对炉黑ｐＨ值与反应时间ｔ之间关系的影响可归因于流化床内单位时间臭氧与炉黑的重量比值Ｒ．炉黑达到相同的ｐＨ值时,反应时间与Ｒ成正比,最终得到了炉黑ｐＨ值随反应时间变化的关联式．     

A critical review of the complex pressure fluctuation phenomenon in gas-solids fluidized beds

The complex pressure fluctuation phenomenon in gas-solid fluidized beds is systematically examined in this paper based on a comprehensive review of the literature data. The local pressure fluctuations are composed of multiple sources, including local bubble induced fluctuations, global bed oscillations and propagating pressure waves originating in other locations (e.g. bed surface, distributor and windbox). The interaction and coupling among bubble motion, under-damped oscillations of fluidized particles and bed surface, propagating compressible pressure waves and flow pulsation in gas-solid fluidized beds creates the complexity of local pressure fluctuations, and is likely responsible for the formation of complex but unique flow patterns. A few attempts have been reported in the literature on examining the interaction between bed oscillations, plenum chamber air pulsation and propagating pressure waves in fluidized beds, showing some promises on predicting the local pressure fluctuations. Future work should be focused on predicting local and global pressure fluctuations and the formation of unique surface flow patterns by coupling different contributing mechanisms.     

一种气,固流化床料位检测的新方法

料位高度是气、固流化床内重要的基本参数之一。虽然有压降法、测温法、电容法和回波法等可用于料位的测量,但是这些方法作为工业应用都不能令人满意。本文根据流化床内部特性提出了利用流化床内压力波动信号和料面附近的平均压力降测量流化床料位高度的新方法。实验表明,这种方法原理简单,测量精度高。不仅能测量流化床内料位的平均高度。而且还能得到料位的瞬时高度和波动范围;且测量结果不受流化床的几何尺寸、床内物料的特性及流化状态等因素的影响,从而为工业流化床提供了一种料位在线测量的新方法。     

振动流化床与浸没水平管平均传热特性理论分析与实验研究

在二维流化床(240mm×80mm)中,以平均粒径dp为1.83mm的玻璃珠为物料,研究了振动流化床与浸没水平管间传热规律;考察了流化数、振动频率、床高、水平管管径等因素对平均传热系数的影响。采用自制探头对浸没加热管束和振动流化床层间平均传热系数进行实验测定,利用颗粒团模型,建立了振动流化床层与浸没水平管间平均传热模型,并对平均传热系数的理论预测值与实验测定值进行了比较。结果表明:计算值与实验值吻合较好,误差在±15%范围内。在较高流化数、低振动频率时,实验值处于理论值上方;随着振动频率、管径增大,平均传热系数实验值逐渐趋于理论预测值甚至低于理论预测值。结果可为带浸没水平管的振动流化床设计和研究提供参考。     

Geldart-B类颗粒在气固流化床中的床层膨胀与流型转变

采用理论推导和经验公式相结合方法,建立了Geldart-B类颗粒在流化床中流化过程的床层膨胀比(R)的通式,并在全取值范围内构建了床层膨胀比的收敛迭代公式。采用不同颗粒的流化实验数据对上述通式(模型)进行了验证,结果表明该模型很好地预测了床层膨胀比。进一步讨论了床层膨胀比与鼓泡流化流型变化之间的关系,给出了临界膨胀比的取值规律。有关床层膨胀比的研究结果一定程度上可有效改善流化床的监控,优化操作条件选取。     

气固脉冲流化床流体力学特性的研究

在φ７０ｍｍ的流化床内，采用聚氯乙烯、玻璃珠和不规则天然刚玉等Ｂ类、Ｄ类颗粒，测定了０￣５．０Ｈｚ脉冲频率下气固流化床的基本流体力学特性，探讨了影响床层流化特性的一些主要因素，并根据实验数据对脉冲流化床的临界流化速度和临界流化压降的无因次准数式进行了关联。     

Optimal placement of probes for dynamic pressure measurements in large-scale fluidized beds

Pressure data sampled at sufficiently high frequency (typically 20 Hz or higher) can yield much information about the hydrodynamic state of a fluidized bed. Since part of the pressure waves travelling through large (industrial) fluidized beds is only detectable in a limited area of the bed, pressure measurements need to be performed at several positions to cover the whole bed. We examine these local pressure waves (caused by, e.g., passing bubbles or coalescing bubbles) in a 0.80 m i.d. bubbling fluidized bed of Geldart B particles. Experiments and simulations are performed to determine the intensity decrease as local pressure waves propagate from their origin. A new spectral method is applied to determine the degree of coherence for pressure signals measured at two different positions in a fluidized bed. For a superficial gas velocity of 5u_mf, local pressure waves can be detected up to a radial distance of about 0.5 m from their origin; this distance is somewhat lower for lower gas velocities. This means that the radial spacing of pressure probes should not exceed 1 m. For large diameter beds with a bed height below 1.5 m, a set of probes at a single level and at several radial positions is sufficient to observe or monitor the dynamic state of the complete bed; the probes should preferably be placed at a height of 30% to 40% of the total bed height.     

A Discussion on Minimum Spout Velocity and Jet Penetration Length

The similarity and difference between the flat‐bottom and cone‐bottom cylindrical spouted beds, conical spouted beds and vertical upward jets in fluidized beds have been analyzed in this paper based on the effects of geometrical parameters on the minimum spouting velocity and operating stabilities of the spouted beds. The effect of angle on minimum spouting velocity was found to be only significant within the range of 30 to 60 degrees cone angles. Minimum spouting velocity in deep cylindrical spouted beds was proportional to the square root of the static bed height, but was proportional to the static bed height in conical spouted beds and large cylindrical spouted beds with small height‐to‐diameter ratio. The relationship between the minimum spouting velocity and the static bed height was consistent with that between jet velocity and the vertical jet penetration length in jetting fluidized beds.     

Hydrodynamics of an inverse liquid–solid circulating conventional fluidized bed

An inverse liquid–solid circulating conventional fluidized bed (I-CCFB) is realized by injecting particles from the top of a conventional liquid–solid fluidized bed (0.076 m ID and 5.4 m height) that is operated in a newly developed circulating conventional fluidization regime located between the conventional and circulating fluidization regimes. The I-CCFB can achieve a higher solids holdup compared to both conventional and circulating liquid–solid fluidized beds. A new parameter, the bed intensification factor, is defined to quantify the increased solids holdup observed with external solids circulation. The Richardson–Zaki equation is shown to be applicable to the I-CCFB regime and can be used to correlate the slip velocity and solids holdup, both of which increase with the solids circulation rate. A new flow regime map is presented, including the I-CCFB and a variety of other liquid–solid fluidized beds.     

微小流化床流化特性分析

在内径4.3, 5.5, 10.5, 15.5, 20.5和25.5 mm的6个气固微小流化床中,考察了石英砂和不同粒径的催化裂化催化剂的流化特性. 研究了流化床尺寸、颗粒及流化介质物性对微小流化床床层压降及最小流化速度的影响. 结果表明,不同颗粒及流化介质的微小流化床床层压降实验值均小于计算值. 传统的压降关联式不能直接用于微小流化床. 其最小流化速度随床径减小呈指数增大,在高径比1:1~3:1范围内,最小流化速度随料高增大近似呈线性增大,其增大速度随床径增大而变缓. 基于实验数据得出了微小流化床最小流化速度的关联式.     

Expansion Behavior of a Binary‐Solid Liquid Fluidized Bed with Large Particle Size Difference

The overall expansion of two dissimilar solid particle species with over a tenfold difference in their size and substantial density difference is investigated here for different compositions of the fluidized bed. Contrary to the widely held notion that the total bed height would be the sum of the heights of the two segregated mono‐component beds, the actual bed heights were, in fact, found to be lower. This volume contraction is found to strongly depend upon the mixing behavior prevailing in the binary‐solid fluidized bed. At the complete mixing of the two solid species, the bed‐contraction versus liquid velocity profile shows a global maximum. As a result, the overall bulk density profiles are similarly affected. Moreover, it is found here that correlations meant for predicting the porosity of the packing of binary particle mixtures can be satisfactorily extended to binary‐solid fluidized beds where solid species differ significantly in size.     

On the heat transfer mechanism in three phase fluidized beds

A two resistance model is proposed for the heat transfer between a coaxially mounted heater and a three phase fluidized bed. Effects of gas and liquid velocity and particle size on individual heat transfer resistances in the heater and in the fluidized bulk zones have been determined. The optimum bed porosity at which the maximum heat transfer coefficient occurred coincided with the bed porosity at which the boundary layer thickness around the heater attained a minimum value. The fluidized bed resistance attained its minimum value when the maximum heat transfer coefficient is achieved in two and three phase fluidized beds. The heat transfer in the zone adjacent to the healer is found to be the rate controlling step since the contribution of fluidized bed resistance was found to be less than 10% of the heater zone resistance in two and three phase fluidized beds. The heat transfer resistances in liquid and three-phase fluidized beds have been represented by a modified Stanton and Peclet numbers based on the heat transfer resistances in the heater zone and in the fluidized bulk zone in series.     

国内外生物质气化设备研究进展

生物质是重要的可再生能源,生物质气化技术在国内外得到了广泛应用。本文综述了国内外固定床、鼓泡流化床、外循环流化床、内循环流化床、双循环流化床的结构。固定床安装简单,但焦油较多;外循环流化床燃烧效率高,但回料装置较难控制;内循环流化床不易结焦、氢含量高且不用考虑返料问题;双流化床结构复杂但焦油量少。将对固定床和流化床进行对比,认为固定床安装简单适合农村地区,流化床应不断改进和完善,更适应工业化生产。     

气-固微型流化床压降特性及最小流化速度的实验研究

在内径3～20 mm的4个气-固微型流化床中,分别考察了A类和B类两种类型颗粒的流化特性,同时研究了床几何结构、操作条件、物相性质等各因素对其最小流化速度的影响.结果 表明,气-固微型流化床中的床层压降特性与颗粒类型密切相关,不同的流动状态下两种类型颗粒的流动特性存在显著地差异.在固定床阶段,与B类颗粒相比,A类颗粒与...     

床形结构对气固流化床流化质量和气体返混特性的影响

用实验方法比较了一个二维床和一个大型三维床内FCC颗粒流化床在鼓泡域和湍动域内的流化质量和气体返混特性。实验结果表明,床形对A类颗粒气固流化床具有非常大的影响。二维床和三维床的流动和气固混合行为既具有相似性,如床膨胀随气速的变化趋势;也具有很大的差异性,既包括三维床流化质量差、轴向气体扩散系数大等量上的不同,又包括压力脉动、轴向气体扩散系数的变化趋势以及湾流模式等质上的不同。总之,在本研究中,二维床体现的是一种具有强烈壁效应的小型流化床的特征,而三维床则体现的是静床高度具有很大影响的大型流化床的特征。     

微型流化床内气体返混

微型流化床基础和应用在近几年受到越来越多的关注。针对微型流化床对气固反应分析的应用要求,利用脉冲示踪法研究了内径10 mm和21 mm两种尺寸微型流化床中的气体返混特性,具体考察了管内径、颗粒静床高度、床料颗粒粒径和气体表观流速对气体返混程度的影响。结果表明:随着床内径、颗粒静床高度和表观气速的减小和床料颗粒粒径的增大,气体在床内的返混程度减小。使用粒径约270 μm粗颗粒时,两种床径的浅层微型流化床中的气体返混程度都较小,对应的Peclet数在27以上,证明了床内气体流动接近平推流,从而为利用微型流化床最小化气体返混对反应测试的影响,获得近本征反应动力学参数提供了流动特性的保障。     

Fluidization and slugging in large-particle systems

Square-nose slugging that occurs with large particles in relatively small-diameter fluidized beds shows certain similarities with the fluidization behaviour in a fluidized bed coal combustion system with closely packed heat-exchanger tubes. In the present investigation, square-nose slugging is studied in fluidized beds of 0.1 and 0.15 m I.D. with coarse sand and alumina particles, at ambient conditions. Recording of pressure fluctuations was used to analyse the fluidization behaviour. A remarkable change in the pressure fluctuation pattern occurs at the transition from normal fluidization to slugging: a more regular signal with a narrowed frequency spectrum is found.In the square-nose slugging regime, the pressure fluctuations seem to be caused by the disintegration of a rising solids slug, followed by the raining down of the particles. Experimental evidence for this mechanism was found in the behaviour of the magnitude of the pressure fluctuations as a function of operating variables.The frequency of square-nose slugging increases with approximately the square root of the bed diameter and appears to be independent of the type of particles used. The slug frequency decreases slightly with the gas velocity between about 0.8 and 1.8 m.s⁻¹, and is inversely proportional to the stationary bed height between 0.15 and 0.4 m.     

脉动流化床的数值模拟

运用Fluent 6．3中的欧拉-欧拉模型模拟传统流化床与锯齿形波脉动进气流化床的运动特性，并进行对比，针对沿床高的气泡高度、当量直径及内压等因素进行分析，得出脉动锯齿形波进气流化效果比传统流化效果明显提高。