PP/PVC/PP-HBP共混体系研究

研究了聚丙烯接枝超支化聚(酰胺-酯)(PP-HBP)对聚丙烯／聚氯乙烯(PP／PVC)共混体系力学性能的影响。结果表明，在PP／PVC(质量比为70／30)共混体系中加入5份PP-HBP时，共混物拉伸强度和冲击强度均出现最大值。扫描电子显微镜（SEM)研究结果证明，PP-HBP增强了PP／PVC的界面粘结作用，减小了共混体系的相分离程度。     

Miscibility,phase behavior,and mechanical properties of ternary blends of poly(vinyl chloride)/polystyrene/chlorinated polyethylene-graft-polystyrene

The effectiveness of chlorinated polyethylene-graft-polystyrene (CPE-g-PS) as a polymeric compatibilizer for immiscible poly(vinyl chloride)/polystyrene (PVC/PS) blends was investigated. The miscibility, phase behavior, and mechanical properties were studied using differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), Izod impact tests, tensile tests, and scanning electron microscopy (SEM). DSC and DMA studies showed that PVC is immiscible with chlorinated polyethylene (CPE) in CPE-g-PS, whereas the PS homopolymer is miscible with PS in CPE-g-PS. The PVC/PS/CPE-g-PS ternary blends exhibit a three-phase structure: PVC phase, CPE phase, and PS phase that consisted of a PS homopolymer and PS in CPE-g-PS. The mechanical properties showed that CPE-g-PS interacts well with both PVC and PS and can be used as a polymeric compatibilizer for PVC/PS blends. CPE-g-PS can also be used as an impact modifier for both PVC and PS. SEM observations confirmed, after the addition of CPE-g-PS, improvement of the interfacial adhesion between the phases of the PVC/PS blends. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 995–1003, 1998     

Compatibilization of PS and PA6 Blends by Means of Poly(oxyalkylene)amine Modified Styrene-Maleic Anhydride Copolymer

The compatibilization effect of SMA-co-M2070-co-DAP comb-like copolymers, SMMD, on immiscible blends of polystyrene (PS) and polyamide-6 (PA6) is examined in terms of phase structure, thermal behavior, dynamic mechanical analysis, and mechanical properties. A series of SMMD copolymers are synthesized and confirmed by the FT-IR analysis. These compatibilizers have different amphiphilic properties depending on the content of hydrophilic poly(oxyethylene) segments (M2070) and the molar ratio of MA/amine. The morphologies of PS/PA6, affected by the increasing amount of SMMD compatibilizer, show a more regular and finer dispersion. The sizes of dispersed particles have no marked changes over the saturation level of compatibilizer. The glass transition temperatures of the blends are between that of PS and PA6, while the added SMMD copolymer is mainly located at the interface. Using these SMMD copolymers, the compatibilized blends show some improvements in mechanical properties, including Izod impact strength and flexural properties. The graft poly(oxyethylene) and amide functionalities in SMMD structures in forming hydrogen bonding with PA6 and, the polystyrene backbone in π–π interaction with PS facilitate the compatibilizing effect.     

超支化聚（酰胺-酯）／ABS／聚氯乙烯共混体系相容性研究

研究了超支化聚(酰胺-酯)(HBP)对ABS/聚氯乙烯(ABS/PVC)共混体系的增容作用。讨论了HBP用量对ABS/PVC(80/20)和相同量HBP对不同比例ABS/PVC力学性能的影响。实验结果表明ABS/PVC共混物中加入HBP,可以有效改善共混体系的相容性;加入2份HBP时,ABS/PVC(80/20)共混物拉伸强度达到最大值,继续增加HBP,共混物拉伸强度快速下降,而共混物冲击强度单调下降;不同比例ABS/PVC中加入2份HBP共混物拉伸强度比未加入HBP共混物拉伸强度增加,但共混物冲击强度减小。扫描电子显微镜研究结果证明了HBP增强了ABS/PVC的界面黏结作用,减小了共混体系的相分离程度。     

Effects of processing conditions and copolymer molecular weight on the mechanical properties and morphology of compatibilized polymer blends

The mechanical properties and morphology of melt mixed polystyrene (PS)/polyethylene (PE) blends that were modified by the addition of up to 16% of a semicrystalline PS-b-hPB (hydrogenated polybutadiene) diblock copolymer with varying molecular weight are reported. As a result of the blocks of the copolymer penetrating the corresponding homopolymers, these diblock copolymers are capable of reinforcing the PS/PE interface significantly. This increase in interfacial strength between the immiscible blend components does not necessarily result in an improvement in the mechanical properties of the blends as measured by Izod or tensile tests. This may be because the effect of the copolymers on the rheological properties of the blends during processing outweighs their emulsifying/reinforcing effects. If found to be universally true for polymer blends, these results suggest that the relationship between the effects of copolymers on interfacial strength, their emulsifying effects, and the mechanical properties of copolymer modified blends are not as simple as suggested by many statements found in the literature.     

Compatibilization efficiency of styrene–butadiene triblock copolymers in polystyrene–polypropylene blends with varying compositions

The compatibilization efficiency of two styrene‐butadiene‐styrene triblock copolymers with short (SB1) and long (SB2) styrene blocks was studied in polystyrene (PS)–polypropylene (PP) blends of composition 20, 50, and 80 wt % PS. The supramolecular structure of the blends was determined by small‐angle X‐ray scattering, and the morphology was studied with transmission electron microscopy and scanning electron microscopy. Structural changes in both the uncompatibilized and compatibilized blends were correlated with the values of tensile impact strength of these blends. Even though the compatibilization mechanisms were different in blends with SB1 and SB2, the addition of the block copolymers to the PS–PP 4/1 and PS–PP 1/4 blends led to similar structures and improved the mechanical properties in the same way. These block copolymers had a very slight effect on the impact strength in PS–PP 1/1 blends, exhibiting a nearly cocontinuous phase morphology. The strong migration of SB2 copolymers to the interface and of SB1 copolymers away from the interface were detected during the annealing of compatibilized PS–PP 4/1 blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2431–2441, 2004     

Thermal and mechanical properties of electron beam irradiated poly(vinyl chloride)/polystyrene blends

The effect of electron beam irradiation on the thermal and mechanical properties of poly(vinyl chloride)/polystyrene (PVC/PS) blends and PVC/PS blends containing epoxidized natural rubber (ENR) was studied. The thermogravimetric analysis study showed that the thermal decomposition of the plasticized PVC individual polymer goes through two stages, whereas PS decomposes through one stage. However, the temperature of the maximum rate of reaction (T_max) of PS is much higher than that for PVC and their blends. Meanwhile, the T_max was found to increase with increasing PS ratios in the blend. The thermal stability of PVC/PS blends was greatly increased after electron beam irradiation in comparison with unirradiated blends. Moreover, the addition of ENR to PVC/PS increased the thermal stability. On the other hand, the mechanical properties in terms of tensile strength and elongation at break of PVC/PS blends are lower than pure PVC polymer because of the immiscibility. However, the addition of ENR to the PVC/PS (80/20) blend increased the elongation at break from 114 to 321% associated with a small effect on the tensile properties. These behaviors were supported by structure morphology studies observations, which indicate an improvement in the interfacial adhesion between the phases. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Application of phase dispersion–crosslinking synergism on recycling commingled plastic wastes

A tetra‐component blend, consisting of low‐density polyethylene (LDPE), polyvinyl chloride (PVC), polypropylene (PP), and polystyrene (PS), was studied as a model system of commingled plastic wastes (LDPE/PVC/PP/PS, mass ratio: 70/10/10/10). Effects of chlorinated polyethylene (CPE), ethylene–propylene–diene monomer (EPDM), styrene–butadiene–styrene (SBS), and their mixture (CPE/EPDM/SBS, mass ratio: 2/2/2) on the mechanical properties and morphology of the system were investigated. With addition of several elastomers and their mixture, the tensile strength of the blends decreased slightly, although both the elongation at break and the impact strength increased. Among these elastomers, EPDM exhibited the most significant impact modification effect for the tetra‐component blends. SBS and the mixture have a good phase‐dispersion effect for the tetra‐component blend. By adding a crosslinking agent [dicumyl peroxide (DCP)], the mechanical properties of the tetra‐component blends also increased. When either SBS or the mixture was added to the blend together with DCP, the probability that the crosslinking agent (DCP) would be at the interface improved because of the phase‐dispersion effect of SBS. Therefore, more co‐crosslinked products will form between LDPE and other components. Accordingly, remarkable improvement of the interfacial adhesion and hence the mechanical properties of the tetra‐component blends occurred. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2947–2952, 2001     

Mechanical Properties and Morphology of Recycled. Plastic Wastes by Solution Blending

In this study, bottles of mineral water and yogurt as well as Styrofoam bowls were recycled and identified by infrared spectroscopy as poly(vinyl chloride) (PVC), high-impact polystyrene (HIPS), and polystyrene (PS). Solution blending was employed to make polymer blends from these recycled plastics, including PVC/PS, PVC/HIPS/PS blends, and PVC/HIPS blends with or without a com-patibilizer, styrenelp-chlorostyrene (ST-CMS). Thermal behavior from differential scanning calorimetry was used to examine the compatibility of the blends. For the PVC/PS and PVC/HIPS/PS systems, it is found that although the third component (HIPS) may not be good enough as a compatibilizer, the addition of HIPS to the two-component blend (PVC/PS) may enhance the mechanical properties at the specific composition, especially for the blends at the intermediate concentrations. For PVC/HIPS blends with the ST-CMS copolymer as a compatibilizer, all the mechanical properties of the blends except the elongation at break, in general, increased with increasing the concentration of compatibilizer due to the increase of compatibility. The abnormal fracture strain was attributed to the differences in adhesion when various amounts of ST-CMS was added. The results of mechanical properties of the blends were consistent with the morphology from scanning electron microscopy.     

Investigation of multiphase polymeric systems of PVC

Graft copolymers of chlororubber-20-g-(ethylacrylate-co-acrylonitrile (2:1)) and chlororubber-20-g-(styrene-co-vinyl acetate-co-acrylonitrile [1:1:1]) have been synthesized by solution precipitation polymerization technique. The graft copolymers have been characterized by elemental analysis, IR spectroscopy, and viscometry. The graft copolymers have been melt blended with PVC. The mechanical properties, such as flexural, tensile strength, and impact strength, of the blends have been studied to evaluate the relative performance of various graft copolymer blends of PVC as impact modified systems. Mechanical properties of the blends have been discussed in terms of morphology of impact fractured samples.     

Thermoplastic composites from maleic anhydride modified post-consumer plastics

In attempts to identify potential applications for refined commingled postconsumer plastics, a feedstock containing about 80% polyethylene (PE) and lesser amounts of poly(ethylene terephthalate) (PET), polystyrene (PS), polypropylene (PP), and poly(vinyl chloride) (PVC) was modified through functionalization with maleic anhydride in a co-rotating intermeshing twin-screw extruder. The modified and unmodified blends were compounded with various fillers and reinforcements such as glass fibers, mica flakes, talc, and calcium carbonate. Injection molded composites based on the modified matrix had, in general, superior mechanical and thermal properties. These findings are discussed in view of the improved adhesion resulting from reactions and/or enhanced polar interactions at phase boundaries. Several compounds prepared in this work had overall property data comparable to, or approaching those, of equivalent commercial HDPE molding compounds that are commonly used in “durable” applications.     

Morphology property relationships in poly (2-methoxy)cyanurate of bisphenol-C (PMCBC)/polystyrene (PS) blends — dynamic modulus

The dynamic mechanical, thermal, and morphological properties of poly(2-methoxy)cyanurate of bisphenol-C (PMCBC), polystyrene (PS), and their blends have been investigated. Dynamic mechanical data show that there is appreciable adhesion at the PMCBC/PS interface but that the PMCBC/PS blends are incompatible. Morphological and thermal analysis results indicate that the PS appears as inclusions in the PMCBC matrix and as a result of interfacial adhesion contributes substantially to the sample's overall modulus. Theories based on perfect adhesion are found to be applicable to the PMCBC/PS blends.     

Polystyrene/EVA melt blends compatibilized with EVA-graft-polystyrene

The influence of poly[(ethylene-co-vinyl acetate)-g-polystyrene] (EVA-g-PS) on the mechanical and morphological properties of polystyrene and the blends with EVA copolymers has been investigated. The melt blends have been performed in a twin-screw extruder. The addition of the graft copolymer enhances the mechanical properties and impact resistance of the PS matrix and PS/EVA (90 : 10 wt %) blends. Better results on impact strength and elongation at break have been achieved by using a EVA-g-PS graft copolymer with a higher EVA proportion by weight. This graft copolymer also contains a lower molecular weight of the PS-grafted segments than the PS matrix. Morphological studies by scanning electron microscopy revealed some interfacial adhesion between the components in the compatibilized polymer blends. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65: 2141–2149, 1997     

Compatibility of waste rubber powder/polystyrene blends by the addition of styrene grafted styrene butadiene rubber copolymer: effect on morphology and properties

Waste rubber powder/polystyrene (WRP/PS) blends with different weight ratio were prepared with styrene grafted styrene butadiene rubber copolymer (PS-g-SBR) as a compatibilizer. The graft copolymer of PS-g-SBR was synthesized by emulsion polymerization method and confirmed through Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC). The copolymer at different weight ratio was subsequently added into the blends. The effects of weight ratio of WRP/PS and compatibilizer loading on mechanical properties were investigated. PS/WRP blends in a weight ratio of 80/20 showed higher impact strength. Moreover, the impact strength of the blend materials increased with the addition of SBR-g-PS, however, decreased at a high loading of the copolymer. The morphology and thermal properties of WRP/PS blends were examined by DSC, scanning electron microscopy (SEM), thermogravimetry (TG). DSC indicated that compared with PS/WRP blend, the glass transition temperature (T _g) of PS matrix phase in PS/WRP/SBR-g-PS blend shifted to low temperature because of the formation of chemical crosslinks or boundary layer between PS and WRP, and the T _g of WRP phase of both the PS/WRP and PS/WRP/SBR-g-PS blends did not appear. SEM results showed that interfacial adhesion in the blends with the PS-g-SBR copolymer was improved. The morphology was a typical continuous–discontinuous structure. PS and WRP presented continuous phase and discontinuous phase, respectively, indicating the moderate interface adhesion between WRP and PS matrix. TG illustrated that the onset of degradation temperature in the PS/WRP/PS-g-SBR blend decreased slightly by contrast with PS/WRP blend and the degradation of PS/WRP blends with and without SBR-g-PS was completed about at the same values.     

Compatibilizers for recycling of the plastic mixture wastes. II. The effect of a compatibilizer for binary blends on the properties of ternary blends

In this article, we discuss the effect of a compatibilizer for binary blends on the properties of ternary blends composed of high‐density polyethylene (HDPE), polypropylene (PP), or polystyrene (PS) and poly(vinyl chloride) (PVC) virgin polymers with a simulated waste plastics fraction. Chlorinated polyethylene (CPE), ethylene–propylene rubber (EPR), and their 1/1 (w/w) mixture were tested as compatibilizers for the HDPE/PP/PVC ternary blend. CPE, styrene‐ethylene‐propylene block copolymer (SEP), or their 1/1 (w/w) mixture were tested as compatibilizers for the HDPE/PS/PVC ternary blend. The composition of the ternary blends were fixed at 8/1/1 by weight ratio. The amount of the compatibilizer was 3 phr. Rheological, mechanical, and thermal properties were measured. For the 8/1/1 HDPE/PP/PVC ternary blends, the tensile strength was slightly decreased, but the impact strength was significantly increased by adding EPR, CPE, or their mixture. EPR exhibited the most significant impact modification effect for the ternary blends. In a similar way, for 8/1/1 HDPE/PS/PVC ternary blends, on adding SEP, CPE, or their mixture, the tensile strength was slightly decreased, but the impact strength was noticeably increased. It was found that the SEP worked much better as an impact modifier for the ternary blends than CPE or the SEP/CPE mixture did. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1048–1053, 2000     

Morphology and mechanical properties of poly(propylene)/polystyrene blends compatibilized with polystyrene-block-poly(ethylene-co-propylene)

Compatibilizing effects of diblock copolymer polystyrene-block-poly(ethylene-co-propylene) (SEP) on the morphology and mechanical properties of immiscible blends of poly(propylene) (PP) and polystyrene (PS) were investigated. Notched impact strength, yield stress, elongation at yield and Young's modulus were determined as a function of different weight ratios of PP and PS and different amounts of added SEP as well. Scanning electron microscopy revealed a two-phase morphology of PP/PS blends, which exhibit poor mechanical properties. Even 2,5 wt.-% of SEP added to PP/PS blends can improve the notched impact strength and elongation at yield compared to non-compatibilized PP/PS blends. 10 wt.-% of SEP compatibilizer converted the brittle PP/PS blend to quite impactresistant polymeric material. Mechanical properties were improved because of the morphological changes and increased interfacial adhesion as a result of SEP localization between PP and PS phases. An analysis of yield stress data in terms of theoretical models showed that yield stress values of binary PP/PS blends can be predicted with Nielsen's model.     

PVC/ABS共混体系力学性能的研究

用冲击试验机、材料试验机和另外一些相关的仪器对PVC/ABS共混体系的力学性能进行了测试、研究,结果发现,PVC/ABS共混体系的性能是组分的函数。ABS的加入改善了PVC/ABS共混体系的力学性能,随着ABS的增加,体系的冲击强度和断裂伸长率明显地提高,而体系的拉伸强度、拉伸模量几乎是随ABS含量的增加而单调地下降。     

Morphology of HDPE/(PEC/PS) blends modified with SEBS copolymers

In this study, immiscible blends of HDPE and an amorphous glassy polymer were compatibilized with styrene-hydrogenated butadiene block copolymers. The glassy phase consisted of either pure PS or a miscible blend of PS and polyether copolymer (PEC); PEC is similar to poly(2,6-dimethyl-1,4-phenylene oxide) (PPO). The morphology of these two-phase mixtures depended on physical characteristics of the components and the method of fabrication. Suitable copolymers increased the degree of dispersion and minimized heterogeneities resulting from the inherent incompatibility of the individual phases. Further reduction in the phase size and increased adhesion between the components of modified blends were achieved by increasing the composition of PEC in the glassy phase. It was concluded that favorable exothermic mixing between PEC and PS endblocks of the copolymers provided an additional driving force for compatibilization. Results from dynamic mechanical thermal analysis suggests that penetration by the copolymers into the homopolymer phases is not complete.     

Toughness,dynamic mechanical property,and morphology of polyvinylchloride/acrylonitrile‐styrene‐butyl acrylate blends

Acrylonitrile‐styrene‐butyl acrylate (ASA) graft copolymers with different acrylonitrile (AN) contents, the core‐shell ratio, and tert‐dodecyl mercaptan (TDDM) amounts were synthesized by seed emulsion polymerization. Polyvinylchloride (PVC)/ASA blends were prepared by melt blending ASA graft copolymers with PVC resin. Then the toughness, dynamic mechanical property, and morphology of the PVC/ASA blends were investigated. The results indicated that the impact strength of the PVC/ASA blends increased and then decreased with the increase of the AN content in poly(styrene‐co‐acrylonitrile (SAN) copolymer, and increased with the increase of the core‐shell ratio of ASA. It was shown that brittle‐ductile transition of PVC/ASA blends was dependent on poly(butyl acrylate) (PBA) rubber content in blends and independent of AN content in SAN copolymer. The introduction of TDDM made the toughness of PVC/ASA blends poor. Dynamic mechanical analysis (DMA) curves exhibited that PVC and SAN copolymers were immiscible over the entire AN composition range. From scanning electron microscopy (SEM), it was found that the dispersion of ASA in PVC/ASA blends was dependent on the AN content in SAN copolymer and TDDM amounts. J. VINYL ADDIT. TECHNOL., 22:43–50, 2016. © 2014 Society of Plastics Engineers     

Investigation of multiphase polymeric systems of poly(vinyl chloride)/ethylene-propylene-diene-gp-(styrene-CO-acrylonitrile) blends

The graft copolymer, ethylene-propylene-diene rubber (EPDM)-gp-(styrene-co-acrylonitrile) has been synthesized by solution precipitation polymerization using benzoyl perixide as initiator. The graft copolymer has been characterized after separation through soxhlet extraction by IR, NMR, and elemental analysis techniques. The graft copolymer of EPDM is melt blended with PVC. The nature of compatibility of the graft copolymers with PVC has been studied by means of morphological analysis and by thermal analysis. The mechanical properties, Izod impact strength, tensile strength, and flexural modulus of the blends are extensively studied over the wide range of concentrations. The results of both compatibility and mechanical properties are compared with those of PVC/EPDM blends. The nature of compatibility obtained shows that PVC/EPDM blends are incompatible and the PVC/EPDM-gp-SAN system is semicompatible. Also, these results indicate that the PVC/EPDM-gp-SAN system has its highest impact strength at 14 wt% of EPDM/gp-SAN graft copolymer. The fractured surface analysis of the impact fractured samples is also undertaken by an SEM technique. The results of the mechanical properties are discussed in view of existing theories of impact modification, along with the morphological feature of fractographs.