Modification and compatibility of epoxy resin with hydroxyl-terminated or amine-terminated polyurethanes

Phenolic hydroxyl-terminated (HTPU) and aromatic amine-terminated (ATPU) PU modifiers were prepared by reacting two different macroglycols (PTMG, polytetramethylene glycol, M_n = 2000, and PBA, Polybutylene adpate, M_n = 2000) with 4,4′-diphenylmethane diisocyanate (MDI), then further coupling with two different coupling agents, bisphenol A or 4,4′-diaminodiphenyl sulfone (DDS). These four types of PU prepolymers were used to modify the epoxy resin with 4,4′-diamino-diphenyl sulfone as a curing agent. From the experimental results, it was shown that the values of fracture energy, G_IC, for PU-modified epoxy were dependent on the macroglycols and the coupling agents. Scanning electron microscopy (SEM) revealed that the ether type (PTMG) of PU-modified epoxy showed the presence of an aggregated separated phase, which varied between 0.5 μm and 4 μm in the ATPU (PTMG) and between 1 μm and 1.5 μm in HTPU (PTMG) modified system. On the contrary, the ester type (PBA) PU-modified epoxy resin showed a homogeneous morphology and consequently a much smaller effect on toughening for its good compatibility with the epoxy network. In addition, it was found that the hydroxyl-terminated bisphenol A as a coupling agent improved fracture toughness more than the amine-terminated DDS because of effective molecular weight buildup by a chain extension reaction. The glass transition temperature (T_g) of modified epoxy resin as measured by dynamic mechanical analysis (DMA) was lower in PTMG-based PU than in a PBA-based PU series with the same weight of modifier.     

Modification of aromatic diamine-cured epoxy resins by poly(oxymethylene) or hybrid modifiers containing poly(oxymethylene)

A copolymer comprising poly(oxymethylene) (POM, polyacetal) was used to improve the fracture toughness of a resin based on diglycidyl ether of bisphenol A (DGEBA) cured with 3,3′-dimethyl-5,5′-diethyl-4,4′-diaminodiphenyl methane. POM was a less effective modifier for epoxies and a third component was used as a toughener or a compatibilizer for POM. The third component includes polypropylene glycol-type urethane prepolymer (PU) and aromatic polyesters. The hybrid modifiers composed of POM and PU were more effective as modifiers for toughening epoxies than POM alone. In the ternary DGEBA/POM/PU (90/10/10wt ratio) blend, the fracture toughness, K_IC, for the modified resin increased 50% with retention of flexural properties and a slight decrease in glass transition temperature (T_g) compared with those of the unmodified epoxy resin. The aromatic polyesters include poly(ethylene phthalate) (PEP), the related copolyesters and poly(butylene phthalate). PEP was most effective of them as a third component in the hybrid modifier. In the ternary DGEBA/POM/PEP (85/15/10) blend, K_IC for the modified resin increased 70% with medium loss of flexural strength and retention of T_g. The toughening mechanism is discussed in terms of morphological and dynamic viscoelastic behaviour of the modified epoxy resin systems. ©1997 SCI     

Toughening of aromatic diamine-cured epoxy resins by poly(butylene phthalate)s and the related copolyesters

Aromatic polyesters, prepared by the reaction of aromatic dicarboxylic acids and 1,4-butanediol, were used to improve the toughness of bisphenol-A diglycidyl ether epoxy resin cured with p,p′-diaminodiphenyl sulfone. These polyesters contained poly(butylene phthalate)s (PBP), poly(butylene phthalate-co-butylene isophthalate)s, poly(butylene phthalate-co-butylene terephthalate)s, and poly(butylene phthalate-co-butylene 2,6-naphthalene dicarboxylate)s. All aromatic polyesters used in this study were soluble in the epoxy resin without solvents and were found to be effective as modifiers for toughening the cured epoxy resin. For example, the inclusion of 20 wt % PBP (MW 16,300) led to a 120% increase in the fracture toughness (K_IC) of the cured resin with no loss of mechanical and thermal properties. The toughening mechanism was discussed in terms of the morphological and dynamic viscoelastic behaviors of the modified epoxy resin system. © 1996 John Wiley & Sons, Inc.     

Multifunctional epoxy resins

The curing behavior of epoxy resins prepared by reacting epichlorohydrin with 4,4′-diaminodiphenyl methane (DADPM)/4,4′-diaminodiphenyl ether (DADPE) or 4,4′-diaminodiphenyl sulfone (DDS) was investigated using DDS and tris-(m-aminophenyl)phosphine oxide (TAP) as curing agents. A broad exothermic transition with two maxima were observed in the temperature range of 100–315°C when TAP was used as the curing agent. The effect of varying DDS concentration on curing behavior of epoxy resin was also investigated. Peak exotherm temperature (T_exo) decreased with increasing concentration of DDS, whereas heat of curing (ΔH) increased with an increase in amine concentration up to an optimum value and then decreased. Thermal stability of the resins, cured isothermally at 200°C for 3 h, was investigated using thermogravimetric analysis in a nitrogen atmosphere. Glass fiber-reinforced multifunctional epoxy resin laminates were fabricated and the mechanical properties were evaluated. © 1993 John Wiley & Sons, Inc.     

Preparation of epoxy-terminated poly(aryl ether sulfone)s and their use as modifiers for epoxy resins

Epoxy-terminated poly(aryl ether sulfone)s (PSE) were prepared by the reaction of epichlorohydrin with hydroxyethyl-terminated polysulfones, which were synthesized from chloro-terminated polysulfones (PSC) and diethanolamine. Both PSE and PSC were used as modifiers for toughening of bisphenol A diglycidyl ether epoxy resin cured with p,p′-diaminodiphenyl sulfone. The mechanical, thermal, and dynamic viscoelastic properties of the modified resins were examined and compared to the parent epoxy resin. The effectiveness of PSC was larger than that of PSE. The fracture toughness, K_IC, for the modified resin increased 45% at slight expense of its mechanical properties on 20 wt % addition of PSC (M_w 5300). These results were discussed in terms of the morphological and dynamic viscoelastic behaviors of the modified epoxy resin system.     

Torsional braid analysis of the aromatic amine cure of epoxy resins

The cure behavior of diglycidyl ether of bisphenol A (DGEBA) type of epoxy resins with three aromatic diamines, 4,4′-diaminodiphenyl methane (DDM), 4,4′-diaminodiphenyl sulfone (44DDS), and 3,3′-diaminodiphenyl sulfone (33DDS) was studied by torsional braid analysis. For each curing agent the stoichiometry of the resin mixtures was varied from a two to one excess of amino hydrogens per epoxy group to a two to one excess of epoxy groups per amino hydrogen. Isothermal cures of the resin mixtures were carried out from 70 to 210°C (range depending on epoxy—amine mixture), followed by a temperature scan to determine the glass transition temperature (T_g). The times to the isothermal liquid-to-rubber transition were shortest for the DDM mixtures and longest for the 44DDS mixtures. The liquid-to-rubber transition times were also shortest for the amine excess mixtures when stoichiometry was varied. A relatively rapid reaction to the liquid-to-rubber transition was observed for the epoxy excess mixtures, followed by an exceedingly slow reaction process at cure temperatures well above the T_g. This slow process was only observed for epoxy excess mixtures and eventually led to significant increases in T_g. Using time—temperature shifts of the glass transition temperature vs. logarithm of time, activation energies approximately 50% higher were derived for this process compared to those derived from the liquid-to-rubber transition. The rate of this reaction was virtually independent of curing agent and was attributed to etherification taking place in the epoxy excess mixtures. © 1994 John Wiley & Sons, Inc.     

Modification of epoxy resins with acrylic rubbers containing a pendant epoxy group

New acrylic rubbers with a pendant epoxy group were prepared by copolymerization of butyl acrylate (BA) with vinylbenzyl glycidyl ether (VBGE). The modification of an epoxy system (bisphenol-A diglycidyl ether/p,p′-diaminodiphenyl sulfone) with the acrylic rubbers was carried out in order to increase the toughness of the cured epoxy resin. The addition of 20 wt.-% of the copolymer containing 74% of BA and 26% of VBGE units resulted in a 30% increase in the fracture toughness (K_IC) of the cured resin at minimal expenses of strength and modulus of the resin. The modified epoxy resin had two-phase morphology in which the rubber particles with average diameter of 2 μm are dispersed in the epoxy matrix. The copolymer without the pendant epoxy group, prepared from BA and vinylbenzyl methoxyethyl ether, was ineffective as a modifier, indicating that the reaction of the pendant epoxide with the epoxy matrix resulted in good interfacial adhesion between the rubber particles and the matrix, and in the increased toughness. The epoxide-containing copolymers with 55 or 86% of BA units were also insufficient modifiers. The addition of the former yielded cured resins with homogeneous structure, whereas that of the latter resulted in macroscopic phase separation between the rubber and the epoxy resin.     

Toughening of epoxy resin by functional‐terminated polyurethanes and/or semicrystalline polymer powders

Hydroxyl‐, amine‐, and anhydride‐terminated polyurethane (PU) prepolymers, which were synthesized from polyether [poly(tetramethylene glycol)] diol, 4,4′‐diphenylmethane diisocyanate, and a coupling agent, bisphenol‐A (Bis‐A), 4,4′‐diaminodiphenyl sulphone (DDS), or benzophenonetetracarboxylic dianhydride, were used to modify the toughness of Bis‐A diglycidyl ether epoxy resin cured with DDS. Besides the crystalline polymers, poly(butylene terephthalate) (PBT) and poly(hexamethylene adipamide) (nylon 6,6), with particle sizes under 40 μm were employed to further enhance the toughness of PU‐modified epoxy at a low particle content. As shown by the experimental results, the modified resin displayed a significant improvement in fracture energy and also its interfacial shear strength with polyaramid fiber. The hydroxyl‐terminated PU was the most effective among the three prepolymers. The toughening mechanism is discussed based on the morphological and the dynamic mechanical behavior of the modified epoxy resin. Fractography of the specimen observed by the scanning electron microscopy revealed that the modified resin had a two‐phase structure. The fracture properties of PBT‐particle‐filled epoxy were better than those of nylon 6,6‐particle‐filled epoxy. Nevertheless, the toughening effect of these crystalline polymer particles was much less efficient than that of PU modification. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2903–2912, 2001     

Toughening of aromatic diamine-cured epoxy resins by modification with hybrid modifiers composed of N-phenylmaleimide–styrene copolymers and N-phenylmaleimide–styrene–p-hydroxystyrene terpolymers

Hybrid modifiers composed of N-phenylmaleimide–styrene copolymers (PMS), and N-phenylmaleimide–styrene–p-hydroxystyrene terpolymers (PMSH) containing pendent p-hydroxyphenyl groups as functionalities, were used to improve the toughness of bisphenol-A diglycidyl ether epoxy resin cured with p,p′-diaminodiphenyl sulphone. The hybrid modifiers were effective in toughening the epoxy resin. When using the modifier composed of 10 wt% PMS (M?_w 313000) and 2.5 wt% PMSH (2.5 mol% p-hydroxystyrene units, M?_w 316000), the fracture toughness (K_IC) for the modified resins increased 100% with no deterioration in the flexural properties and the glass transition temperature. The improvement in toughness of the epoxy resins was attained because of the co-continuous phase structure and the improvement in interfacial adhesion. The toughening mechanism is discussed in terms of the morphological characteristics of the modified epoxy resin systems.     

Toughening of Diglycidyl Ether of Bisphenol-A Epoxy Resin Using Poly (Ether Ether Ketone) with Pendent Ditert-Butyl Groups

Poly(ether ether ketone) (PEEKDT), hydroxyl terminated poly(ether ether ketone) (PEEKDTOH) and fluorine terminated poly (ether ether ketone) (PEEKDTF) with pendent ditert-butyl groups were synthesized by the nucleophilic substitution reaction of 4,4′-difluorobenzophenone with 2,5-ditert-butylhydroquinone in N-methyl-2-pyrrolidone medium using anhydrous potassium carbonate as catalyst. Diglycidyl ether of bisphenol-A epoxy resin was blended with PEEKDT, PEEKDTOH, and PEEKDTF, and cured with 4,4′-diaminodiphenylsulfone (DDS). The polymers formed heterogeneous blends before curing, and upon curing the polymers got dispersed in the epoxy matrix. The mechanical properties of the cured blends were slightly lower than that of the unmodified resin. The fracture toughness increased with the addition of ditert-butyl PEEK into epoxy resin and the extent of improvement was dependent on the type of modifier used. Hydroxyl terminated polymers gave up to 40% increase in fracture toughness. The dynamic mechanical spectrum of the blends showed only a single T_g due to the proximity of the glass transition temperature of modified PEEK and DDS cured epoxy resin.     

Hydroxyl terminated poly(ether ether ketone) with pendent methyl group toughened epoxy resin: miscibility, morphology and mechanical properties

The synthesis, processing, thermal and mechanical properties and fracture toughness of epoxy resin formulated with hydroxyl terminated poly(ether ether ketone) with pendent methyl group are reported. Hydroxyl terminated poly(ether ether ketone) oligomers based on methyl hydroquinone (PEEKMOH) were synthesised from methylhydroquinone and 4,4′-difluorobenzophenone in N-methyl-2-pyrrolidone. PEEKMOH oligomers with different molecular weights were synthesised and characterised. Blends of diglycidyl ether of bisphenol-A epoxy resin with PEEKMOH were prepared by melt mixing. The uncured blends were homogeneous and the T_g-composition behaviour was predicted using Fox, Gordon–Taylor and Kelley–Bueche equations. Reaction induced phase separation occurred in the blends on curing with 4,4′-diaminodiphenyl sulfone. Scanning electron microscopy studies revealed the two-phase morphology of the blends. Domain size of the blends increased with increase in PEEKMOH8 in the blends. Phase separation in the blends occurred by nucleation and growth mechanism. Infrared spectroscopic studies revealed that some of the epoxy groups were opened up by hydroxyl group of PEEKMOH. The tensile and flexural properties of the blends were comparable to that of neat epoxy resin and the properties were dependent on the composition of the blend and molecular weight of PEEKMOH used. Dynamic mechanical analysis revealed two glass transition temperatures corresponding to epoxy rich and thermoplastic rich phases. The crosslink density of epoxy resin decreased with the addition of PEEKMOH to epoxy resin. The blends exhibited superior fracture toughness compared to unmodified epoxy resin. The increase in fracture toughness was due to local plastic deformation of the matrix, crack path deflection and crack pinning. The thermal stability of amine cured epoxy resin was not affected by the incorporation of PEEKMOH into the epoxy resin.     

Physicomechanical Properties of Carbon Fiber Reinforced Epoxy Composites

Fabrication of carbon fiber reinforced epoxy composites from the matrix resins diglycidyl ether of bisphenol-A (DGEBA) and tetraglycidyl bis(aminotolyl) cyclohexane (TGBATC) using 4,4′-diaminodiphenyl methane (DDM) as curing agent. The composites were evaluated for their physical and mechanical properties. A significant improvement in the properties was observed on addition of 20 phr of an epoxy fortifier.     

Dynamic mechanical experiments for probing process-structure-property relations in amine-cured epoxies

Dynamic mechanical experiments were performed on an amine-cured high performance epoxy system containing two types of epoxies and one amine. The system approximates a commercial resin system used widely as matrix material for graphite composites and whose main ingredients and composition are 88.5 percent of tetraglycidyl 4,4′-diamino diphenyl methane (TGDDM) and 11.5 percent of polyglycidyl ether of Bisphenol A Novalac epoxy with varying compositions of 4,4′-diaminodiphenyl sulfone (DDS), ranging from 19 to 40 PHR. Specifically, the effects of DDS and Novalac content as well as processing conditions including the particle size of solid components, the mixing speed, mixing temperature, and the mixing duration of the components on the dynamic mechanical properties of the epoxy polymer were investigated. A viscoelastic transition in the dynamic spectrum which was observed to be quite sensitive to the sample's T_g in conjunction with incomplete crosslinking reactions allowed for interrelating the composition and processing variables to the structure and bulk properties of this epoxy system.     

Thermal and mechanical properties of poly(urethane‐imide)/epoxy/silica hybrids

Improving properties of polyurethane (PU) elastomers have drawn much attention. To extend the properties of the modified PU composite, here a new method via the reaction of poly(urethane‐imide) diacid (PUI) and silane‐modified epoxy resin (diglycidyl ether of bisphenol A) was developed to prepare crosslinked poly (urethane‐ imide)/epoxy/silica (PUI/epoxy/SiO₂) hybrids with enhanced thermal stability. PUI was synthesized from the reaction of trimellitic anhydride with isocyanate‐terminated PU prepolymer, which was prepared from reaction of polytetramethylene ether glycol and 4,4′‐diphenylmethane diisocyanate. Thermal and mechanical properties of the PUI/epoxy/SiO₂ hybrids were investigated to study the effect of incorporating in situ SiO₂ from silane‐modified epoxy resin. All experimental data indicated that the properties of PUI/epoxy/SiO₂ hybrids, such as thermal stability, mechanical properties, were improved due to the existence of epoxy resin and SiO₂. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Characterization of the cure of TGDDM/DDS epoxy resins by chemiluminescence I. Spectral and thermal analysis

The emission of weak visible chemiluminescence (CL) during the cure of a tetraglycidyl 4,4′-diaminodiphenyl methane (TGDDM)-based epoxy resin, with three different concentrations of 4,4′-diaminodiphenylsulfone (DDS) has been studied at 135°C. Spectral analysis indicates that the CL originates from trace oxidation of the TGDDM resin and the emission intensity is sensitive to the viscosity changes during cure. From thermal analysis data, sharp discontinuities in CL intensity are shown to occur at the gel point. The temperature dependence of CL from a cured resin also shows a sharp discontinuity at T_g. These results indicate that CL provides a sensitive monitor of both the kinetics of gelation and the network formation in this epoxy resin.     

DOPO-based curing flame retardant of epoxy composite material for char formation and intumescent flame retardance

Phosphorus-containing flame retardant (HBAEA-DOPO) for epoxy resin was synthesized by addition reaction of 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) with bis[2-(4-hydroxybenzylideneamino)ethyl]amine (HBAEA) that was synthesized via 4-hydroxybenzaldehyde with diethylenetriamine. HBAEA-DOPO was mixed with 4,4′-diaminodiphenyl sulfone to co-cure the epoxy resin of diglycidyl ether bisphenol A. The silane modified nano-silica (nano-SiO₂) was used to reinforce the epoxy resin. Thermal stability and dynamic mechanical properties of the cured epoxy materials were studied with the use of thermogravimetric analysis and dynamic mechanical thermal analysis. Flame retardance and burning behavior were evaluated by the limiting oxygen index (LOI), vertical burning test, and the cone calorimetry. The cured epoxy materials have excellent thermal stability, and the temperatures at the maximum weight loss rate are over 384.0°C. The characteristic temperature corresponding to 5.00 wt% of thermal decomposition reaches 341.5°C as 1.00 wt% of phosphorus content is loaded. Flame retardant grade meets the V-0 level. The fire residue mass gradually increases with HBAEA-DOPO and nano-SiO₂. The characteristics of high flame retardance and smoke suppression of HBAEA-DOPO and nano-SiO₂ on the cured epoxy composites have been demonstrated to be related to char formation and intumescent flame retardance in the condensed phase.     

Toughening of aromatic diamine-cured trifunctional epoxy resins by modification with N-phenylmaleimide–styrene copolymers containing pendant p-hydroxyphenyl groups

N-Phenylmaleimide (PMI)–N-(p-hydroxy)phenylmaleimide (HPMI)–styrene (St) terpolymers (HPMS), containing pendant p-hydroxyphenyl (HP) groups, were prepared and used to improve the toughness of triglycidyl aminocresol epoxy resin cured with p,p′-diaminodiphenyl sulfone. HPMS was effective as a modifier for the toughening of the epoxy resin. When using 15 wt % of HPMS (1.0 mol % HP unit, M_w 129,000), the fracture toughness (K_IC) for the modified resin increased 190% with a medium loss of flexural strength. The toughening of epoxies could be attained because of the cocontinuous phase structure of the modified resins. The decrease in flexural strength was suppressed to some extent by introducing a functional group into the modifier. The toughening mechanism was discussed in terms of the morphological behavior of the modified epoxy resin system. © 1995 John Wiley & Sons, Inc.     

High performance epoxy resins cured in the presence of BF3 catalyst

Dynamic mechanical experiments have been conducted on an epoxy system made with tetraglycidyl 4,4′-diaminodiphenyl methane (TGDDM) and polyglycidyl ether of Bisphenol A Novalac that were cured with 4,4′-diaminodiphenyl sulfone (DDS) in the presence of Boron trifluoride monoethylamine catalyst (BF₃:EtNH₂). As the concentration of BF₃:EtNH₂ increased, the low temperature β-transition magnitude increased slightly. The α₁-transition observed in the uncatalyzed system decreased significantly with the addition of BF₃:EtNH₂ catalyst. The α₂ or glass transition temperature of this system increased with increasing catalyst concentration. Both the catalyzed and uncatalyzed epoxy formulations studied in this work are important due to their similarity to systems used commercially in epoxy matrix composites.     

Preparation of novel soluble poly(ester imide)s containing a trimellitimide moiety and their use as modifiers for aromatic diamine‐cured epoxy resin

Poly(ester imide)s, prepared by the reaction of phthalic anhydride, N‐(4‐carboxyphenyl) trimellitimide and 1,2‐ethanediol, were used to improve the toughness of bisphenol‐A diglycidyl ether epoxy resin cured with 4,4′‐diaminodiphenyl sulfone (DDS). The poly(ester imide)s include poly(ethylene phthalate‐co‐ethylene N‐(1,4‐phenylene) trimellitimide dicarboxylate)s (PESIs) having 10, 20 and 30 mol% trimellitimide (TI) units, respectively. PESIs having 10 and 20 mol% TI units were effective as modifiers for toughening the cured epoxy resin. For example, the inclusion of 20 wt% of PESI (20 mol% TI unit, M _W 19300 g mol^?1) led to a 55% increase in the fracture toughness (K_IC) of the cured resin (with an increase in flexural strength and modulus) and the modified resin had a particulate morphology. PESI having 30 mol% TI units was not effective because of degradation of the modifier by DDS. The toughening mechanism is discussed in terms of morphological and dynamic viscoelastic behaviour of the modified epoxy resin system. © 2001 Society of Chemical Industry     

Cure kinetics of neat versus reinforced epoxies

An investigation was carried out into the cure kinetics of neat vs reinforced epoxy systems. The formulations were composed of tetraglycidyl 4,4′-diaminodiphenyl methane (TGDDM) epoxy resin and diaminodiphenyl sulfone (DDS). Glass was used as reinforcement. A series of isothermal differential scanning calorimetry (DSC) thermograms were run and analyzed by the proposed autocatalytic kinetic model. An increase in reaction rate was observed at higher temperature and higher DDS concentration in both neat and reinforced formulations. The presence of reinforcement had an effect on the cure kinetics. The observed effect, however, was not very pronounced. Slightly lower values of the reaction rate constant and longer times needed to reach the maximum reaction rate were recorded in reinforced systems. After reaching the peak value, the rate of reaction dropped off faster in reinforced formulations, resulting in lower average value of H_ult, the ultimate heat of reaction. It was suggested that the reinforcement imposes restrictions on the molecular mobility of reactive species.