Structural, optical and electrical properties of AZO/Cu/AZO tri-layer films prepared by radio frequency magnetron sputtering and ion-beam sputtering

Highly conducting tri-layer films consisting of a Cu layer sandwiched between Al-doped ZnO (AZO) layers (AZO/Cu/AZO) were prepared on glass substrates at room temperature by radio frequency (RF) magnetron sputtering of AZO and ion-beam sputtering of Cu. The tri-layer films have superior photoelectric properties compared with the bi-layer films (Cu/AZO, AZO/Cu) and single AZO films. The effect of AZO thickness on the properties of the tri-layer films was discussed. The X-ray diffraction spectra show that all films are polycrystalline consisting of a Cu layer with the cubic structure and two AZO layers with the ZnO hexagonal structure having a preferred orientation of (0 0 2) along the c-axis, and the crystallite size and the surface roughness increase simultaneously with the increase of AZO thickness. When the AZO thickness increases from 20 to 100 nm, the average transmittance increases initially and then decreases. When the fixed Cu thickness is 8 nm and the optimum AZO thickness of 40 nm was found, a resistivity of 7.92 × 10⁻⁵ Ω cm and an average transmittance of 84% in the wavelength range of visible spectrum of tri-layer films have been obtained. The merit figure (F_TC) for revaluing transparent electrodes can reach to 1.94 × 10⁻² Ω⁻¹.     

Study of optoelectronics and microstructures on the AZO/nano-layer metals/AZO sandwich structures

In this study, growth nano-layer metals (Al, Cu, Ag) and Al-doped ZnO (AZO) thin films are deposited on glass substrates as the transparent conducting oxides (TCOs) to form AZO/nano-layer metals/AZO sandwich structures. The conductivity properties of thin films are enhanced when the average transmittance over the wavelengths 400–800 nm is maintained at higher than 80 %. A radio frequency magnetron sputtering system is used to deposit the metal layers and AZO thin films of different thickness, to form AZO/Al/AZO (ALA), AZO/Cu/AZO (ACA) and AZO/Ag/AZO (AGA) structures. X-ray diffraction and field emission scanning electron microscopy are used to analyze the crystal orientation and structural characteristic. The optical transmission and resistivity are measured by UV–VIS–NIR spectroscopy and Hall effect measurement system, respectively. The results show that when the Ag thickness is maintained at approximately 9 nm, the TCOs thin film has the lowest resistivity of 8.9 × 10^?5 Ω-cm and the highest average transmittance of 81 % over the wavelengths 400–800 nm. The crystalline Ag nano-crystal structures are observed by high-resolution transmission electron microscopy. In addition, the best figure of merit for the AZO/Ag/AZO tri-layer film is 2.7 × 10^?2 (Ω^?1), which is much larger than that for other structures.     

透明导电AZO/Cu双层薄膜制备及其性能

采用直流磁控溅射方法在玻璃衬底上室温生长了AZO/Cu双层薄膜,Cu层厚度控制在9nm,研究了AZO层厚度对薄膜电学和光学性能的影响。当AZO层厚度为20～80nm时,AZO/Cu双层薄膜具有良好的综合光电性能,方块电阻为12～14Ω/sq,可见光平均透过率为70～75%,品质因子为2×10-3～5×10-3Ω-1。AZO/Cu双层薄膜可以观察到Cu（111）和ZnO（002）的XRD衍射峰。通过退火研究表明,AZO/Cu双层薄膜的光电性能可在400℃下保持稳定,具有良好的热稳定性。本研究制备的透明导电AZO/Cu双层薄膜具有室温制程、综合光电性能良好、结晶性能较好、稳定性高的优点,可以广泛应用于光电器件透明电极及镀膜玻璃等领域。     

Effects of sputtering pressure and Al buffer layer thickness on properties of AZO films grown by rf magnetron sputtering

Transparent and conductive Al-doped (2 wt.%) zinc oxide (AZO) films were deposited on inexpensive soda-lime glass substrates by using rf magnetron sputtering at room temperature. This study analyzed the effects of argon sputtering pressure, which varied in the range from 0.46 to 2.0 Pa, on the morphological, electrical and optical properties of AZO films. The only (0 0 2) diffraction peak of the film were observed at 2θ～34.45°, exhibiting that the AZO films had hexagonal ZnO wurtzite structure, and a preferred orientation with the c-axis perpendicular to the substrate. By applying a very thin aluminum buffer layer with the thickness of 2 nm, findings show that the electrical resistivity was 9.46 × 10⁻⁴ Ω-cm, and the average optical transmittance in the visible part of the spectra was approximately 81%. Furthermore, as for 10 nm thick buffer layer, the electrical resistivity was lower, but the transmittance was decreased.     

Tungsten-doped ZnO transparent conducting films deposited by direct current magnetron sputtering

Highly conducting and transparent thin films of tungsten-doped ZnO (ZnO:W) were prepared on glass substrates by direct current (DC) magnetron sputtering at low temperature. The effect of film thickness on the structural, electrical and optical properties of ZnO:W films was investigated. All the deposited films are polycrystalline with a hexagonal structure and have a preferred orientation along the c-axis perpendicular to the substrate. The electrical resistivity first decreases with film thickness, and then increases with further increase in film thickness. The lowest resistivity achieved was 6.97 × 10⁻⁴ Ω cm for a thickness of 332 nm with a Hall mobility of 6.7 cm² V⁻¹ s⁻¹ and a carrier concentration of 1.35 × 10²¹ cm⁻³. However, the average transmittance of the films does not change much with an increase in film thickness, and all the deposited films show a high transmittance of approximately 90% in the visible range.     

Deposition of Al-doped ZnO films on polyethylene naphthalate substrate with radio frequency magnetron sputtering

100 nm Al-doped ZnO (AZO) thin films were deposited on polyethylene naphthalate (PEN) substrates with radio frequency magnetron sputtering using 2 wt.% Al-doped ZnO target at various deposition conditions including sputtering power, target to substrate distance, working pressure and substrate temperature. When the sputtering power, target to substrate distance and working pressure were decreased, the resistivity was decreased due to the improvement of crystallinity with larger grain size. As the substrate temperature was increased from 25 to 120 °C, AZO films showed lower electrical resistivity and better optical transmittance due to the significant improvement of the crystallinity. 2 wt.% Al-doped ZnO films deposited on glass and PEN substrates at sputtering power of 25 W, target to substrate distance of 6.8 cm, working pressure of 0.4 Pa and substrate temperature of 120 °C showed the lowest resistivity (5.12 × 10^− 3 Ω cm on PEN substrate, 3.85 × 10^− 3 Ω cm on glass substrate) and high average transmittance (> 90% in both substrates). AZO films deposited on PEN substrate showed similar electrical and optical properties like AZO films deposited on glass substrates.     

Influence of annealing temperature on the properties of ZnO:Zr films deposited by direct current magnetron sputtering

Transparent conducting zirconium-doped zinc oxide (ZnO:Zr) films were deposited on quartz substrates by direct current (DC) magnetron sputtering at room temperature. The influence of post-annealing temperature on the structural, morphological, electrical and optical properties of ZnO:Zr films were investigated. When annealing temperature increases from room temperature to 573 K, the resistivity decreases obviously due to an improvement of the crystallinity. However, with further increase in annealing temperature, the crystallinity deteriorates leading to an increase in resistivity. The films annealed at the optimum annealing temperature of 573 K in vacuum have the lowest resistivity of 9.8 × 10⁻⁴ Ω cm and a high transmittance of above 92% in the visible range.     

The effects of impurity and temperature for transparent conducting oxide properties of Al:ZnO deposited by dc magnetron sputtering

Aluminum-doped zinc oxide films (ZnO:Al) were deposited on Si wafers and glass substrates by dc magnetron sputtering from a ZnO target mixed with 2 wt% Al₂O₃ for photovoltaic films. The effect of base pressure, additional oxygen, and substrate temperature were studied in detail. By dc magnetron sputtering at room temperature, the resistivity and the average transmittance in visible range was 2.3 × 10⁻³ Ω cm and 77.3%, respectively. And these were improved up to 3.3 × 10⁻⁴ Ω cm and 86% at the substrate temperature of 400 °C by high deposition rate and low impurity ambient. The mobility and the carrier concentration were improved by the increased preferred orientation of (002) plane and grain size of film with increasing deposition temperature. This advanced AZO film with good resistivity and transmittance can be expected as the front TCO of thin film solar cells.     

Transparent conductive and infrared reflective AZO/Cu/AZO multilayer film prepared by RF magnetron sputtering

AZO/Cu/AZO multilayer films were prepared on glass substrate by radio frequency magnetron sputtering technology. The prepared films were investigated by a four-point probe system, X-ray diffraction, optical transmittance spectra, scanning electron microscope, atomic force microscopy and Fourier transform infrared spectroscopy. The results showed that Cu inner layer started forming a continuous film at the thickness around 11 nm. The prepared AZO/Cu/AZO samples exhibited the visible transmittance of 60–80 % and sample with 15 nm Cu inner layer showed the highest infrared reflection rate of 67 % in FIR region and the lowest sheet resistance of 16.6 Ω/sq. The proper visible transmittance and infrared reflection property of the AZO/Cu/AZO multilayer film make it a promising candidate for future energy conservation materials.     

Mn-doped ZnO transparent conducting films deposited by DC magnetron sputtering

Mn-doped zinc oxide (ZnO:Mn) thin films with low resistivity and relatively high transparency were firstly prepared on glass substrate by direct current (DC) magnetron sputtering at room temperature. Influence of film thickness on the properties of ZnO:Mn films was investigated. X-ray diffraction (XRD) and scanning electron microscopy (SEM) show that all the deposited films are polycrystalline with a hexagonal structure and have a preferred orientation along the c-axis perpendicular to the substrate. As the thickness increases from 144 to 479 nm, the crystallite size increases while the electrical resistivity decreases. However, as the thickness increases from 479 to 783 nm, the crystallite size decreases and the electrical resistivity increases. When film thickness is 479 nm, the deposited films have the lowest resistivity of 2.1 × 10^− 4 Ω cm and a relatively high transmittance of above 84% in the visible range.     

Annealing effect of ZnO/Au/ZnO transparent conductive films

Au intermediate ZnO (ZAZ) thin films were prepared by radio frequency and direct current magnetron sputtering on glass substrates and then vacuum annealed. The thickness of each layer of the ZAZ films was set at 50 nm, 3 nm, and 47 nm, respectively. The structural, electrical, and optical properties of ZAZ films were investigated with respect to the variation of annealing temperature.As-deposited AZO films showed X-ray diffraction peaks corresponding to ZnO (002) and Au (111) planes and those peak intensities increased with post-deposition vacuum annealing. The optical and electrical properties of the films were strongly influenced by post-deposition annealing. Although the optical transmittance of the films deteriorated with an Au interlayer, as-deposited ZAZ films showed a low resistivity of 2.0 × 10⁻⁴ Ω cm, and the films annealed at 300 °C had a lower resistivity of 9.8 × 10⁻⁵ Ω cm. The work function of the films increased with annealing temperature, and the films annealed at 300 °C had a higher work function of 4.1 eV than the films annealed at 150 °C. The experimental results indicate that vacuum-annealed ZAZ films are attractive candidates for use as transparent electrodes in large area electronic applications such as solar cells and large area displays.     

Structural and opto-electric properties of Ga and F codoped ZnO thin films on PC substrates

Ga–F codoped ZnO (GFZO) thin films were firstly prepared on polycarbonate (PC) substrates by MF magnetron sputtering and the results were compared in detail with the Al doped ZnO (AZO) thin films. The influence of dopants on the structural and optoelectric properties of ZnO films was studied. X-ray diffraction and scanning electron microscopy results show that the cracks formed in both GFZO and AZO films due to the high residual stress, originating from the different thermal expansion coefficients between film/substrate. However, the GFZO films show better crystallinity and deliver larger grain size than AZO. A relative low resistivity of 1.4 × 10⁻³ Ω cm and a transmittance of 81% for the GFZO thin films are achieved, better than that of 2.3 × 10⁻² Ω cm and 75% for the AZO films. The results illustrate that the combined effects of Ga–F codoping and smaller crack density can optimise the opto-electric properties of ZnO based thin films.     

室温下射频磁控溅射制备ZnO:Al透明导电薄膜及其性能研究

采用射频磁控溅射技术,在室温下,以ZnO:Al2O3(2%Al2O3(质量比))为靶材,在石英玻璃基底上,采用不同工艺条件制备了ZnO:Al(AZO)薄膜。使用扫描电子显微镜观察了薄膜的表面形貌,X射线衍射分析了薄膜的结构,四探针测量仪得到薄膜的表面电阻,轮廓仪测量了薄膜厚度,并计算了电阻率,最后采用分光光度计测量了薄膜的透过率;研究了溅射功率、溅射气压与薄膜厚度对薄膜电阻率及透过率的影响。结果表明:所制备的AZO薄膜具有(002)择优取向,并且发现薄膜厚度对薄膜的光电性能有明显影响,溅射气压和溅射功率对薄膜电学性能有较大影响,但是对薄膜透过率影响不大。当功率为1kW、溅射气压0.052Pa、AZO薄膜厚度为250nm时,其电阻率为8.38×10-4Ω·cm,波长在550nm处透过率为89%,接近基底的本底透过率92%。当薄膜厚度为1125 nm时薄膜的电阻率降至最低(6.16×10-4Ω·cm)。     

Influence of Ag thickness of aluminum-doped ZnO/Ag/aluminum-doped ZnO thin films

Highly conducting aluminum-doped ZnO (30 nm)/Ag (5-15 nm)/aluminum-doped ZnO (30 nm) multilayer thin films were deposited on glass substrate by rf magnetron sputtering (for top/bottom aluminum-doped ZnO films) and e-beam evaporation (for Ag film). The transmittance is more than 70% for wavelengths above 400 nm with the Ag layer thickness of 10 nm. The resistivity is 3.71 × 10^− 4 Ω-cm, which can be decreased to 3.8 × 10^− 5 Ω-cm with the increase of the Ag layer thickness to 15 nm. The Haacke figure of merit has been calculated for the films with the best value being 8 × 10^− 3 Ω^− 1. It was shown that the multilayer thin films have potential for applications in optoelectronics.     

Low-temperature deposited Titanium-doped zinc oxide thin films on the flexible PET substrate by DC magnetron sputtering

Transparent conducting Titanium-doped zinc oxide thin films (TZO) with high transparency and relatively low resistivity were firstly deposited on water-cooled polyethylene terephthalate (PET) substrates at room temperature by DC magnetron sputtering. The microstructure, optical and electrical properties of the deposited films were investigated and discussed. The XRD patterns show that all the deposited films are polycrystalline with a hexagonal structure and have a preferred orientation along the c-axis perpendicular to the substrate. The electrical resistivity decreases when the sputtering power increases from 45 W to 60 W. However, as the puttering power continue increases from 60 W to 90 W, the electrical resistivity increases rapidly. When the puttering power is 60 W, the films deposited on PET substrate have the lowest resistivity of 4.72 × 10⁻⁴ Ω cm and a relatively high transmittance of above 92% in the visible range.     

Effects of substrate on the structural, electrical and optical properties of Al-doped ZnO films prepared by radio frequency magnetron sputtering

Transparent and conductive Al-doped ZnO (AZO) thin films were deposited on substrates including alkali-free glass, quartz glass, Si, and SiO₂ buffer layer on alkali-free glass by using radio frequency magnetron sputtering. The effects of different substrates on the structural, electrical and optical properties of the AZO films were investigated. It was found that the crystal structures were remarkably influenced by the type of the substrates due to their different thermal expansion coefficients, lattice mismatch and flatness. The AZO film (100 nm in thickness) deposited on the quartz glass exhibited the best crystallinity, followed sequentially by those deposited on the Si, the SiO₂ buffer layer, and the alkali-free glass. The film deposited on the quartz glass showed the lowest resistivity of 5.14 × 10^− 4 Ω cm among all the films, a carrier concentration of 1.97 × 10²¹ cm^− 3 and a Hall mobility of 6.14 cm²/v·s. The average transmittance of this film was above 90% in the visible light spectrum range. Investigation into the thickness-dependence of the AZO films revealed that the crystallinity was improved with increasing thickness and decreasing surface roughness, accompanied with a decrease in the film resistivity.     

Novel properties of AZO film sputtered in Ar+H2 ambient at high temperature

AZO (ZnO:Al) transparent conductive thin film was prepared by RF magnetron sputtering with a AZO (98 wt% ZnO 2 wt% Al₂O₃) ceramic target in the same Ar+H₂ ambient at different substrate temperatures ranging from 100 to 300 °C. The minimum resistivity of AZO films was 7.9×10⁻⁴ Ω cm at the substrate temperature of 200 °C. The average transmission in the visible rang was more than 90%. Scanning electron microscopy and XRD analyses showed that the surface morphology of the AZO samples altered with the increasing of the substrate temperature. AZO film prepared at 200 °C in the pure Ar ambient was also made as comparison about the resistivity, carrier concentration and the average crystallite size. The resistivity became about 3 times higher. The carrier concentration became lower and the average crystallite size was smaller.     

Effect of deposition parameters and annealing temperature on the structure and properties of Al-doped ZnO thin films

Transparent conductive films of Al-doped ZnO (AZO) were deposited onto inexpensive soda-lime glass substrates by radio frequency (rf) magnetron sputtering using a ZnO target with an Al content of 3 wt%. The Taguchi method with a L₉ orthogonal array, signal-to-noise (S/N) ratio and analysis of variance (ANOVA) were employed to examine the performance characteristics of the coating operations. This study investigated the effect of the deposition parameters (rf power, sputtering pressure, thickness of AZO films, and substrate temperature) on the electrical, structural, morphological and optical properties of AZO films. The grey-based Taguchi method showed the electrical resistivity of AZO films to be about 9.15 × 10⁻³ Ω cm, and the visible range transmittance to be about 89.31%. Additionally, the films were annealed in a vacuum ambient (5.0 × 10⁻⁶ Torr) at temperatures of 400, 450, 500 and 600 °C, for a period of 30 min. It is apparent that the intensity of the X-ray peaks increases with annealing treatment, leading to improved crystallinity of the films. By applying annealing at 500 °C in a vacuum ambient for 30 min, the AZO films show the lowest electrical resistivity of 2.31 × 10⁻³ Ω cm, with about 90% optical transmittance in the visible region and a surface roughness of Ra = 12.25 nm.     

Effect of SiO2 buffer layer thickness on the properties of ITO/Cu/ITO multilayer films deposited on polyethylene terephthalate substrates

Transparent conductive ITO/Cu/ITO films were deposited on polyethylene terephthalate (PET) substrates with a SiO₂ buffer layer by magnetron sputtering using three cathodes at room temperature. The effect of the SiO₂ buffer layer thickness on the electrical and optical properties of ITO/Cu/ITO films was investigated. The ITO/Cu/ITO film deposited on the 40 nm thick SiO₂ buffer layer exhibits a sheet resistance of 143Ω/sq and transmittance of 65% at 550 nm wavelength. Highly transparent ITO/Cu/ITO films with a transmittance of 80% and a sheet resistance of 98.7Ω/sq have been obtained by applying −60 V substrate bias.     

GZO/Ag/GZO多层薄膜制备、结构与光电特性的研究

采用射频磁控溅射和离子束溅射联合设备在玻璃衬底上制备出了具有良好附着性、低电阻率和高透过率的GZO/Ag/GZO(ZnO掺杂Ga_2O_3简称GZO)多层薄膜.X射线衍射谱表明GZO/Ag/GZO多层薄膜是多晶膜,GZO层具有ZnO的六角纤锌矿结构,最佳取向为(002)方向;Ag层是立方结构,具有(111)取向.在GZO层厚度一定的情况下,研究了Ag层厚度的变化对多层膜结构以及光电特性的影响.研究发现,当Ag层厚度为10nm时,3层膜的电阻率为9×10~(-5)Ω·cm,在可见光范围内平均透过率达到89.7%,薄膜对应的品质因子数值为3.4×10~(-2)Ω~(-1).