End-group functionalization of poly(3-hexylthiophene) as an efficient route to photosensitize nanocrystalline TiO2 films for photovoltaic applications

Bulk heterojunction (BHJ) and dye-sensitized solar cells (DSSCs) have seen increased popularity over recent years and each technology has experienced tremendous improvements in power conversion efficiencies (PCEs), reaching 8 and 12%, respectively. The two technologies have been on independent improvement pathways, and this work establishes a link between them by using the archetypical hole conductor (poly-3-hexylthiophene, P3HT) in BHJs as a sensitizer on TiO(2) for DSSC applications. Three polymers were synthesized and examined as potential TiO(2) sensitizers in DSSCs under AM1.5 solar radiation. Using Grignard metathesis, regioregular P3HT was synthesized then functionalized with either one or two cyanoacrylic acid linker moieties to bind to the TiO(2) surface. End-group modification resulted in minimal changes to the optical and electronic properties as compared to pristine P3HT. Cyclic voltammetry (CV) experiments at anodic potentials of adsorbed sensitizer quantified the amount of alkylthiophene adsorbed on the TiO(2), whereas under reductive sweeps, cyanoacrylic acid end-group binding was determined. CVs of each polymer indicated that loading was drastically different as compared to pristine P3HT with the lowest loading on TiO(2) and monofunctionalized P3HT exhibited the highest loading. The DSSCs showed power conversion efficiencies (PCEs) of 0.1%, 0.2 and 2.2% for the polymer-sensitized TiO(2) of the unfunctionalized, monofunctionalized and difunctionalized polymers, respectively. DSSCs were then subjected to electrochemical impedance spectroscopy (EIS) in the dark and under monochromatic light radiation. The large variance in performance for the functionalized-P3HT sensitizers is attributed to differences in the adsorption modes of sensitizer on the TiO(2) surface, which in the difunctionalized case limits electrolyte recombination and favors forward charge transfer reactions.     

Efficiency enhancements in solid-state hybrid solar cells via reduced charge recombination and increased light capture

We compare a series of molecular sensitizers in dye-sensitized solar cells containing the organic hole transporter 2,2',7,7'-tetrakis(N,N-di-p-methoxypheny-amine)-9,9'-spirobifluorene (spiro-MeOTAD). Charge recombination is reduced by the presence of "ion-coordinating" moieties on the dye, with the longest electron lifetime and highest solar cell efficiency achieved using a novel sensitizer with diblock alkoxy-alkane pendent groups. By further increasing the optical path length in the active layer, we achieve a power conversion efficiency of over 5% under simulated sun light.     

Simple indoline based donor–acceptor dye for high efficiency dye-sensitized solar cells

A simple metal-free donor–acceptor type sensitizer U01, bearing strong electron donor indoline-triphenylamine was synthesized for panchromatic sensitization of TiO₂ nanocrystalline film. Photovoltaic properties of U01 showed remarkably enhanced light harvesting due to the presence of strong electron donor and robust structure. The new U01 sensitized solar cell exhibited a photovoltaic performance: a short-circuit photocurrent density (J_sc) of 10.70 mA cm⁻², an open-circuit photovoltage (V_oc) of 0.758 V and a fill factor (FF) of 0.74, corresponding to an overall conversion efficiency of 6.01% under standard global AM 1.5 solar light condition. Our results suggest that indoline-triphenylamine based robust D–A molecular architecture is a highly promising class of panchromatic sensitizers for improvement of the performance of dye-sensitized solar cells (DSCs).     

Efficient triphenylamine photosensitizers with alkoxy- or fluorine-substituted phenylene spacer for dye-sensitized solar cells

Two new organic sensitizers (TP1–2) containing triarylamine donor and a cyanoacrylic acid acceptor bridged by alkoxy- or fluorine-substituted phenylene spacer have been synthesized and explored as a sensitizer in dye-sensitized solar cells (DSCs). The absorption spectra, electrochemical and photovoltaic properties of TP1–2 are extensively investigated. The DSC based on dye TP1 shows the best photovoltaic performance: a short-circuit photocurrent density (J _SC) of 13.5 mA cm⁻², an open-circuit photovoltage (V _OC) of 702 mV, and a fill factor (ff) of 0.68, corresponding to an overall conversion efficiency of 6.4% under standard global AM1.5 solar light conditions. The results demonstrate that structural modification of substituting groups on π-spacer is importance for realizing a high efficiency DSC.     

Halogen-Free Donor Polymers Based on Dicyanobenzotriazole with Low Energy Loss and High Efficiency in Organic Solar Cells

Halogenation of organic semiconductors is an efficient strategy for improving the performance of organic solar cells (OSCs), while the introduction of halogens usually involves complex synthetic process and serious environment pollution problems. Herein, three halogen-free ternary copolymer donors (PCNx, x = 3, 4, 5) based on electron-withdrawing dicyanobenzotriazole are reported. When blended with the Y6, PCN3 with strong interchain interactions results in appropriate crystallinity and thermodynamic miscibility of the blend film. Grazing-incidence wide-angle X-ray scattering measurements indicate that PCN3 has more ordered arrangement and stronger π–π stacking than previous PCN2. Fourier-transform photocurrent spectroscopy and external quantum efficiency of electroluminescence measurements show that PCN3-based OSCs have lower energy loss than PCN2, which leads to their higher open-circuit voltage (0.873 V). The device based on PCN3 reaches power conversion efficiency (PCE) of 15.33% in binary OSCs, one of the highest values for OSCs with halogen-free donor polymers. The PCE of 17.80% and 18.10% are obtained in PM6:PCN3:Y6 and PM6:PCN3:BTP-eC9 ternary devices, much higher than those of PM6:Y6 (16.31%) and PM6:BTP-eC9 (17.33%) devices. Additionally, this ternary OSCs exhibit superior stability compared to binary host system. This work gives a promising path for halogen-free donor polymers to achieve low energy loss and high PCE.     

Solution-processed small-molecule solar cells with 6.7% efficiency

Organic photovoltaic devices that can be fabricated by simple processing techniques are under intense investigation in academic and industrial laboratories because of their potential to enable mass production of flexible and cost-effective devices. Most of the attention has been focused on solution-processed polymer bulk-heterojunction (BHJ) solar cells. A combination of polymer design, morphology control, structural insight and device engineering has led to power conversion efficiencies (PCEs) reaching the 6-8% range for conjugated polymer/fullerene blends. Solution-processed small-molecule BHJ (SM BHJ) solar cells have received less attention, and their efficiencies have remained below those of their polymeric counterparts. Here, we report efficient solution-processed SM BHJ solar cells based on a new molecular donor, DTS(PTTh(2))(2). A record PCE of 6.7% under AM 1.5 G irradiation (100 mW cm(-2)) is achieved for small-molecule BHJ devices from DTS(PTTh(2))(2):PC(70)BM (donor to acceptor ratio of 7:3). This high efficiency was obtained by using remarkably small percentages of solvent additive (0.25% v/v of 1,8-diiodooctane, DIO) during the film-forming process, which leads to reduced domain sizes in the BHJ layer. These results provide important progress for solution-processed organic photovoltaics and demonstrate that solar cells fabricated from small donor molecules can compete with their polymeric counterparts.     

Oligoselenophene derivatives functionalized with a diketopyrrolopyrrole core for molecular bulk heterojunction solar cells

Solution-processable oligoselenophenes functionalized with diketopyrrolopyrrole cores have been synthesized for use as the donor material in bulk heterojunction solar cells. The optical absorption of these materials extends to the edge of the visible spectrum. Power conversion efficiencies of 1.53 ± 0.04% for DPPS and 0.84 ± 0.04% for DPPDS were obtained under simulated 100 mW/cm(2) AM 1.5G irradiation for devices when PC(61)BM was used as an acceptor. DPPS showed hole mobilities of 4 × 10(-5) cm(2)/(V s) and a peak external quantum efficiency (EQE) of 25%, while DPPDS showed hole mobilities of 2 × 10(-5) cm(2)/(V s) and a peak EQE of 19%. To the best of our knowledge, these are the first oligoselenophenes that have been reported in molecular bulk heterojunction solar cells and this study could serve as a springboard for the design and optimization of high-performance selenophene-containing photovoltaics.     

An Efficient, “Burn in” Free Organic Solar Cell Employing a Nonfullerene Electron Acceptor

A comparison of the efficiency, stability, and photophysics of organic solar cells employing poly[(5,6‐difluoro‐2,1,3‐benzothiadiazol‐4,7‐diyl)‐alt‐(3,3′″‐di(2‐octyldodecyl)‐2,2′;5′,2″;5″,2′″‐quaterthiophen‐5,5′″‐diyl)] (PffBT4T‐2OD) as a donor polymer blended with either the nonfullerene acceptor EH‐IDTBR or the fullerene derivative, [6,6]‐phenyl C₇₁ butyric acid methyl ester (PC₇₁BM) as electron acceptors is reported. Inverted PffBT4T‐2OD:EH‐IDTBR blend solar cell fabricated without any processing additive achieves power conversion efficiencies (PCEs) of 9.5 ± 0.2%. The devices exhibit a high open circuit voltage of 1.08 ± 0.01 V, attributed to the high lowest unoccupied molecular orbital (LUMO) level of EH‐IDTBR. Photoluminescence quenching and transient absorption data are employed to elucidate the ultrafast kinetics and efficiencies of charge separation in both blends, with PffBT4T‐2OD exciton diffusion kinetics within polymer domains, and geminate recombination losses following exciton separation being identified as key factors determining the efficiency of photocurrent generation. Remarkably, while encapsulated PffBT4T‐2OD:PC₇₁BM solar cells show significant efficiency loss under simulated solar irradiation (“burn in” degradation) due to the trap‐assisted recombination through increased photoinduced trap states, PffBT4T‐2OD:EH‐IDTBR solar cell shows negligible burn in efficiency loss. Furthermore, PffBT4T‐2OD:EH‐IDTBR solar cells are found to be substantially more stable under 85 °C thermal stress than PffBT4T‐2OD:PC₇₁BM devices.     

Diketopyrrolopyrrole-based π-bridged donor-acceptor polymer for photovoltaic applications

We report the synthesis, properties, and photovoltaic applications of a new conjugated copolymer (C12DPP-π-BT) containing a donor group (bithiophene) and an acceptor group (2,5-didodecylpyrrolo[3,4-c]pyrrole-1,4(2H,5H)-dione), bridged by a phenyl group. Using cyclic voltammetry, we found the energy levels of C12DPP-π-BT are intermediate to common electron donor and acceptor photovoltaic materials, poly (3-hexylthiophene-2,5-diyl) (P3HT) and [6,6]-phenyl-C61-butyric acid methyl ester (PCBM), respectively. Whereas P3HT and PCBM are exclusively electron donating or accepting, we predict C12DPP-π-BT may uniquely serve as either an electron donor or an acceptor when paired with PCBM or P3HT forming junctions with large built-in potentials. We confirmed the ambipolar nature of C12DPP-π-BT in space charge limited current measurements and in C12DPP-π-BT:PCBM and C12DPP-π-BT:P3HT bulk heterojunction solar cells, achieving power conversion efficiencies of 1.67% and 0.84%, respectively, under illumination of AM 1.5G (100 mW/cm(2)). Adding diiodooctane to C12DPP-π-BT:PCBM improved donor-acceptor inter-mixing and film uniformity, and therefore enhanced charge separation and overall device efficiency. Using higher-molecular-weight polymer C12DPP-π-BT in both C12DPP-π-BT:PCBM and C12DPP-π-BT:P3HT devices improved charge transport and hence the performance of the solar cells. In addition, we compared the structural and electronic properties of C12DPP-π-BT:PCBM and C12DPP-π-BT:P3HT blends, representing the materials classes of polymer:fullerene and polymer:polymer blends. In C12DPP-π-BT:PCBM blends, higher short circuit currents were obtained, consistent with faster charge transfer and balanced electron and hole transport, but lower open circuit voltages may be reduced by trap-assisted recombination and interfacial recombination losses. In contrast, C12DPP-π-BT:P3HT blends exhibit higher open circuit voltage, but short circuit currents were limited by charge transfer between the polymers. In conclusion, C12DPP-π-BT is a promising material with intrinsic ambipolar characteristics for organic photovoltaics and may operate as either a donor or acceptor in the design of bulk heterojunction solar cells.     

Enhanced light harvesting from Först-type resonance energy transfer in the quasi-solid state dye-sensitized solar cells

The demonstrated F?rst-type resonance energy transfer (FRET) is demonstrated in quasi-solid type dye-sensitized solar cells between organic fluorescence materials as an energy donor doped in polymeric gel electrolyte and a ruthenium complex as an energy acceptor on the surface of TiO2. Strong spectral overlap of emission/absorption of the energy donor and acceptor is required to obtain high FRET efficiency. The judicious choice of the energy donor allows the enhancement of the light harvesting characters of the energy acceptor (N3) in quasi-solid dye sensitized solar cells which increases the power conversion efficiency by 25% compare to that of a pristine cell. The optimized cell architecture fabricated with the quasi-solid type electrolyte containing fluorescence materials shows a maximum efficiency of 5.08% with a short-circuit current density (J(sc)) of 12.63 mA/cm2, and an open-circuit voltage (V(oc)) of 0.70 V under illumination of simulated solar light (AM 1.5, 100 mW/cm2).     

Influence of position of auxiliary acceptor in D–A–π–A photosensitizes on photovoltaic performances of dye-sensitized solar cells

Several novel indoline dyes configured with donor–acceptor–bridge–acceptor (D–A–π–A) structures were designed and applied to organic dye-sensitized solar cells. These D–A–π–A dye molecules are composed of indoline (electron donating group), benzothiadiazole (BDT) (auxiliary acceptor), two furan rings (π-conjugated group), and 2-cyanoacrylic acid (electron accepting group). The influence of position of auxiliary acceptor in D–A–π–A organic sensitizer on the performance of photosensitize is investigated in detail. Calculated results show that the sensitizer could achieve a red-shifted absorption in long-wavelength region and a stronger absorption in short-wavelength region when the position of auxiliary acceptor changes from the donor to the acceptor. Moreover, among these dyes, WS-12, whose auxiliary acceptor nearing the 2-cyanoacrylic acid, possesses the better performance in terms of the charge transfer characteristics, lifetime of excited state as well as the vertical dipole moment when compared with WS-1 and WS-11. We hope that the present results could provide theoretical guidance for designing photosensitizes with higher efficiencies.     

Synthesis of high quality zinc-blende CdSe nanocrystals and their application in hybrid solar cells

Oleic acid (OA) modified zinc-blende cadmium selenium nanocrystals (NCs) with different diameters, 3-5?nm, have been prepared. We find that the morphology and fluorescent properties of the samples are related to the preparation conditions such as the chain-length and concentration of the cadmium precursor as well as the concentration of OA. The hybrid solar cells based on the obtained spherical CdSe NCs as an acceptor and Poly(2-methoxy-5-(2'-ethylhexoxy)-p-phenylenevinylene) (MEH-PPV) as a donor show an energy conversion efficiency (ECE) as high as 0.85%, three times higher than that reported before for spherical CdSe NCs/conjugated polymer hybrid solar cells. When poly(3-hexylthiophene) (P3HT) is used as the donor phase instead of MEH-PPV, the energy conversion efficiency increases up to 1.08%. The solar cell based on CdSe NCs/conjugated polymer has the potential to open up new production technologies for hybrid solar cells based on semiconductor NCs.     

染料敏化太阳能电池天然敏化剂的研究进展

染料敏化剂是影响染料敏化太阳能电池(DSC)性能的重要因素。介绍了染料敏化剂的分类及获得高效、稳定的电池时染料敏化剂需要满足的条件,根据天然染料敏化剂的分类,分别介绍了叶绿素类、花青素类、类胡萝卜素类以及单宁酸等天然染料作为DSC敏化剂的研究进展及其区别,指出对天然染料敏化剂的研究有利于降低染料敏化太阳能电池的生产成本并促进其工业化发展。     

Efficient TCO-free organic solar cells with modified poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) anodes

Organic photovoltaic cells (OPVs) with a highly conductive poly 3,4-ethylenedioxythiophene:poly styrenesulfonate (PEDOT:PSS) layer as an anode and that were modified with the addition of some organic solvents such as sorbitol (So), dimethyl sulfoxide (DMSO), N-methyl-pyrrolidone (NMP), dimethylformamide (DMF), and ethylene glycol (EG) were fabricated without the use of transparent conducting oxide (TCO). The conductivity of the PEDOT:PSS film that was modified with each additive was enhanced by three orders of magnitude. According to the atomic force microscopy (AFM) study, the conductivity enhancement might have been related to the better connections between the conducting PEDOT chains. The TCO-free solar cells with a modified PEDOT:PSS layer and an active layer composed of poly (3-hexylthiophene) (P3HT) and phenyl [6, 6] C61 butyric acid methyl ester (PCBM) performed as well as the indium-tin-oxide (ITO)-based organic solar cells. The power conversion efficiency (PCE) of the organic solar cells with a DMSO-, So + DMSO-, and EG-modified PEDOT:PSS layer reached 3.51, 3.64, and 3.77%, respectively, under an illumination of AM 1.5 (100 mW/cm2).     

The function of a TiO2 compact layer in dye-sensitized solar cells incorporating "planar" organic dyes

We present a device based study into the operation of liquid electrolyte dye-sensitized solar cells (DSSC's) using organic dyes. We find that, for these systems, it is entirely necessary to employ a compact TiO2 layer between the transparent fluorine doped SnO2 (FTO) anode and the electrolyte in order to reduce charge recombination losses. By incorporation of a compact layer, the device efficiency can be increased by over 160% under simulated full sun illumination and more than doubled at lower light intensities. This is strong evidence that the more widely employed ruthenium based sensitizers act as to "insulate" the anode against recombination losses and that many planar organic dyes employed in DSSC's could greatly benefit from the use of a compact TiO2 blocking layer. This is in strong contrast to DSSC's sensitized with ruthenium based systems, where the introduction of compact TiO2 has only marginal effects on conversion efficiencies.     

Toward interaction of sensitizer and functional moieties in hole-transporting materials for efficient semiconductor-sensitized solar cells

Sb(2)S(3)-sensitized mesoporous-TiO(2) solar cells using several conjugated polymers as hole-transporting materials (HTMs) are fabricated. We found that the cell performance was strongly correlated with the chemical interaction at the interface of Sb(2)S(3) as sensitizer and the HTMs through the thiophene moieties, which led to a higher fill factor (FF), open-circuit voltage (V(oc)), and short-circuit current density (J(sc)). With the application of PCPDTBT (poly(2,6-(4,4-bis-(2-ethylhexyl)-4H-cyclopenta[2,1-b;3,4-b']dithiophene)-alt-4,7(2,1,3-benzothiadiazole)) as a HTM in a Sb(2)S(3)-sensitized solar cell, overall power conversion efficiencies of 6.18, 6.57, and 6.53% at 100, 50, and 10% solar irradiation, respectively, were achieved with a metal mask.     

Effect of coadsorbent on the photovoltaic performance of squaraine sensitized nanocrystalline solar cells

The effect of chenodeoxycholic acid as the coadsorbent with a squaraine sensitizer on TiO(2) nanocrystalline solar cells was investigated, and it was found that the coadsorbent prevents the squaraine sensitizer from aggregating on the TiO(2) nanoparticles but reduces dye loading leading to an interdependent photovoltaic performance. Analysis of the absorption spectra, and incident monochromatic photon-to-current conversion efficiency data showed that the load of squaraine sensitizer as well as the appearance of H-aggregates is strongly dependent on the molar concentration of chenodeoxycholic acid coadsorbent. The open circuit voltage of the solar cells with chenodeoxycholic acid increases due to the enhanced electron lifetime in the TiO(2) nanoparticles coupled with the band edge shift of TiO(2) to negative potentials.     

Enhanced and Balanced Charge Transport Boosting Ternary Solar Cells Over 17% Efficiency

Ternary architecture is one of the most effective strategies to boost the power conversion efficiency (PCE) of organic solar cells (OSCs). Here, an OSC with a ternary architecture featuring a highly crystalline molecular donor DRTB-T-C4 as a third component to the host binary system consisting of a polymer donor PM6 and a nonfullerene acceptor Y6 is reported. The third component is used to achieve enhanced and balanced charge transport, contributing to an improved fill factor (FF) of 0.813 and yielding an impressive PCE of 17.13%. The heterojunctions are designed using so-called pinning energies to promote exciton separation and reduce recombination loss. In addition, the preferential location of DRTB-T-C4 at the interface between PM6 and Y6 plays an important role in optimizing the morphology of the active layer.     

Asymmetric Electron Acceptors for High-Efficiency and Low-Energy-Loss Organic Photovoltaics

Low energy loss and efficient charge separation under small driving forces are the prerequisites for realizing high power conversion efficiency (PCE) in organic photovoltaics (OPVs). Here, a new molecular design of nonfullerene acceptors (NFAs) is proposed to address above two issues simultaneously by introducing asymmetric terminals. Two NFAs, BTP-S1 and BTP-S2, are constructed by introducing halogenated indandione (A₁) and 3-dicyanomethylene-1-indanone (A₂) as two different conjugated terminals on the central fused core (D), wherein they share the same backbone as well-known NFA Y6, but at different terminals. Such asymmetric NFAs with A₁-D-A₂ structure exhibit superior photovoltaic properties when blended with polymer donor PM6. Energy loss analysis reveals that asymmetric molecule BTP-S2 with six chlorine atoms attached at the terminals enables the corresponding devices to give an outstanding electroluminescence quantum efficiency of 2.3 × 10⁻²%, one order of magnitude higher than devices based on symmetric Y6 (4.4 × 10⁻³%), thus significantly lowering the nonradiative loss and energy loss of the corresponding devices. Besides, asymmetric BTP-S1 and BTP-S2 with multiple halogen atoms at the terminals exhibit fast hole transfer to the donor PM6. As a result, OPVs based on the PM6:BTP-S2 blend realize a PCE of 16.37%, higher than that (15.79%) of PM6:Y6-based OPVs. A further optimization of the ternary blend (PM6:Y6:BTP-S2) results in a best PCE of 17.43%, which is among the highest efficiencies for single-junction OPVs. This work provides an effective approach to simultaneously lower the energy loss and promote the charge separation of OPVs by molecular design strategy.     

16.67% Rigid and 14.06% Flexible Organic Solar Cells Enabled by Ternary Heterojunction Strategy

Ternary heterojunction strategies appear to be an efficient approach to improve the efficiency of organic solar cells (OSCs) through harvesting more sunlight. Ternary OSCs are fabricated by employing wide bandgap polymer donor (PM6), narrow bandgap nonfullerene acceptor (Y6), and PC₇₁BM as the third component to tune the light absorption and morphologies of the blend films. A record power conversion efficiency (PCE) of 16.67% (certified as 16.0%) on rigid substrate is achieved in an optimized PM6:Y6:PC₇₁BM blend ratio of 1:1:0.2. The introduction of PC₇₁BM endows the blend with enhanced absorption in the range of 300–500 nm and optimises interpenetrating morphologies to promote photogenerated charge dissociation and extraction. More importantly, a PCE of 14.06% for flexible ITO‐free ternary OSCs is obtained based on this ternary heterojunction system, which is the highest PCE reported for flexible state‐of‐the‐art OSCs. A very promising ternary heterojunction strategy to develop highly efficient rigid and flexible OSCs is presented.