Specific features of the phase transformations occurring during the sintering process of the beta-alumina based ceramics and their properties

Conclusions During the sintering process of beta-alumina obtained using the method of plasmochemical synthesis, the structural transformation occurs and it is accompanied by the separation of the excess Na₂O and the formation of an intergranular meltlike phase that is saturated with sodium and is characterized by high dielectric properties.The quantity of the meltlike phase and the magnitude of the /( + ) ratio determine the degree of stabilization (stability) and the final resistivity of the material and depend on the initial chemical composition and the heating rate maintained during the sintering process.It was shown that when the duration of residence of the material in the hot zone of the furnace is increased or when the specimens sintered maintaining high heating rates are subjected to additional heat treatment, one observes the occurrance of the reverse structural transformation that is characterized by an increase of the phase ratio /( + ) 1, a reduction in the quantity of the meltlike phase right up to its complete disappearance, and a decrease of the electrical resistivity of the material.In the materials having a large excess quantity of sodium oxide, the process of crystallization of the intergranular NaAlO₂ phase occurs simultaneously with the second phase transformation.The best ceramic and electrophysical parameters were obtained when sintering the material contained 7.9% Na₂O.Translated from Ogneupory, No. 3, pp. 13–18, March, 1990.     

Convective Regime of Filtration Combustion of Energetic Materials in a Cocurrent Flow of Their Combustion Products

The convective regime of filtration combustion of energetic materials in a cocurrent flow of their combustion products is studied using a model with extremely simplified kinetics and heat transfer, which shows instability of the process. It is shown that the more accurate twotemperature model describes a steadystate regime. In this regime, the gas temperature on the hot boundary of the heating zone is well below the combustion temperature, and the solidphase temperature is well below the temperature proposed in recent studies on this topic. It is pointed out that the twotemperature approach is unjustified and intragranular nonisothermicity must be taken into account for convective regimes. It is shown that the threetemperature model, which takes into account this effect, does not give a stable steadystate solution.     

Critical solution point and chain dimension of branched-polystyrene solutions

Summary Critical solution point and chain dimension were measured for branched polystyrene(BPS) in solution as a function of molecular weight(M) and compared with those for linear polystyrene(LPS). The critical concentration _c of BPS was quite different from that of LPS at a fixed M, but the same at a fixed overlap-concentration ^*, i.e., plots of _c vs. ^* fall on a single straight line for both BPS and LPS (gf_c ^*). Reduced critical temperature _c defined by gt_c=(–T_c)/ [T_c: critical temperature, : the -temperature] was related to _c as _{c c} ² for BPS, whereas _{c c} for LPS.     

Quasi‐Homogeneous and Pseudospin Modes of Zirconium‐Wire Combustion in Air

A novel experimental technique is proposed for examining the transition mechanism from quasihomogeneous to heterogeneous combustion — burning of a variablepitch spring. Depending on the pitch of aircombustible zirconium springs, two combustion modes are possible. Quasihomogeneous (layerbylayer) combustion is observed in the case of smallpitch springs; as the spring pitch increases, quasihomogeneous combustion transforms into heterogeneous (pseudospin) combustion. Conditions for the occurrence of various combustion modes, depending on the spring diameter and pitch, are studied.     

Antifungal polyoxygenated fatty acids fromAeollanthus parvifolius

Two polyoxygenated fatty acids with antifungal activity have been isolated from aerial parts ofAeollanthus parvifolius (Labiatae) using bioassay-guided isolation procedures. Spectroscopic analysis was used to identify the compounds as (Z)-4,9-diacetoxy-6,7-epoxy-5-hydroxy-8-oxododeca-2-enoic acid and (Z)-4,6,7,9-tetraacetoxy-5-hydroxy-8-oxododeca-2-enoic acid. Both of these compounds inhibited spore germination ofCladosporium cucumerinum. Minimum inhibitory doses were 1 µg and 5 µg, respectively, but only the former inhibited germination ofAspergillus niger at a dose of 5 µg. Neither compound exhibited antibacterial activity. (Z)-4,9-Diacetoxy-6,7-epoxy-5-hydroxy-8-oxododeca-2-enoic acid reduced the hyphal growth ofPythium ultimum. The mode of action was not resolved but did not involve either the disruption of the cell wall membrane or the inhibition of extracellular enzymes. Application of (Z)-4,6,7,9-tetraacetoxy-5-hydroxy-8-oxododeca-2-enoic acid to seedling plants did not give any protection against fungal attack, and indeed the compound appeared to be phytotoxic.     

Variable‐temperature IR spectroscopic studies of CO adsorbed on Na‐ZSM‐5 and Na‐Y zeolites

CO interacts with extraframework alkali metal cations (M⁺=) of zeolites to form both M⁺CO and M⁺OC species. By using variabletemperature FTIR spectroscopy, these Cbonded and Obonded species were found to be in a temperaturedependent equilibrium. For the same cation, the difference in interaction energy depends upon the zeolite framework. Thus, for the equilibrium process ZNa⁺=CO ZNa⁺OC, where Z represents the zeolite framework, H ⁰ was found to take the values 3.8 and 2.4 kJ mol^– for CO/NaZSM5 and CO/NaY, respectively. The Cbonded species show always the highest cation–CO interaction energy.     

Recovery and recrystallization of electrodeposited bright copper coatings at room temperature. II. X-ray investigation of primary recrystallization

X-ray investigations of the recrystallization processes occurring at room temperature in electrodeposited bright copper coatings were carried outin situ. As a result of the orientation transformation of the growth texture with 311, 111 and 110 components, a recrystallization texture with 100, 110 and 111 components was obtained. It was established that one of the factors which influence the microhardness of copper coatings is the orientation distribution of crystallites.     

Studies concerning charged nickel hydroxide electrodes IV. Reversible potentials in LiOH,NaOH, RbOH and CsOH

The variation of reversible potential E_r with log a_moh and has been studied for several nickel hydroxide/oxyhydroxide couples in various alkali hydroxides. Both activated and deactivated -phase couples show only a small dependence ofE _r with log_moh (or where known) in LiOH, NaOH, RbOH and CsOH electrolytes. The change in MOH content on oxidation/reduction is found to be about 0.1 mol MOH per two-electron transfer and is the same as found previously in KOH. These results confirm that the bulk oxidized -phase lattice is devoid of alkali cation although a small quantity may be adsorbed by the surface. On the other hand both activated and deactivated /-phase couples show a marked dependence of 0.45 mol MOH per two-electron transfer in LiOH, NaOH and RbOH (at concentrations > 0.5 m), also in good agreement with earlier data for KOH. On the basis of these results a general stoichiometry can be inferred for the -phase, namely M_0.32NiO₂ · 0.7H₂O where M=Li⁺, Na⁺, K⁺ or Rb⁺. Measurements imply that the Cs⁺ ion or the Rb⁺ ion at low concentration (<0.5 m) do not enter the interlayer structure of the -phase. This behaviour is thought to be related to the low Rb-O and Cs-O bond strengths afforded by the -phase structure.     

Effect of distortions in the ideal profile of solid phase conductivity on performance efficiency of porouselectrodes

The effect of distortions in the ideal profile of the solid phase conductivity s(x) on porous electrode (PE) performance efficiency has been analysed using a one-dimensional model and an overall polarization curve involving both main and side reactions. Although an ideal electrically equally accessible PE is provided only by a hyperbolic profile s(x) passing through the middle of the electrode (the point s=L), it has been shown that a noticeable improvement in performance can be obtained using a rough approximation with any monotonic function providing a decrease in conductivity in the direction from the back current supply to the front plane of the PE, including functions not necessarily passing through the point s=L in the middle of the electrode. This permits less rigid requirements for the s(x) profile reproduction accuracy and simplification of experimental data acquisition.     

Selective Oxidation of 1- and 2-Propanol with Molecular Oxygen by Noble Metal Catalysis in “Supercritical” Carbon Dioxide

The selective oxidation of 1- and 2-propanol by molecular oxygen over supported platinum catalysts was investigated in supercritical carbon dioxide as an environmentally benign and safe reaction medium. The reaction occurs exclusively to acetone or propionic aldehyde and propionic acid in a single-phase region at 100–190 bar and at a mild temperature (40 °C). Compared to conversions in aqueous solution, catalyst stability is significantly enhanced in supercritical carbon dioxide and depends on the oxygen concentration in the reaction medium. Thus, at least a fourfold higher substrate/catalyst ratio than with water as a solvent can be used. Platinum catalysts with nanoporous silica (MCM-41, silicalite-1) as a support are also active for the oxidation of 2-propanol in supercritical carbon dioxide.     

The photochromism of nitrospiropyran included in γ-cyclodextrin

Summary The inclusion compounds of 1, 3, 3-trimethyl-6-nitrospiro-[2H, 1-benzo-pyran-2, 2-indoline] (NSP) with -cyclodextrin (-CD), 2,3,6,0-permethylated -CD (-MCD), and naphthyl modified -CD (-NCD) showed normal photochromism in the solid state with high light sensitivity comparable with that of NSP dispersed in polymer matrices. This is in sharp contrast with NSP in the crystalline state, which is much less photosensitive. These results suggest that the host cavity offers a sufficient free volume for phototransformation of the guest molecule. The colored form of the inclusion compounds were found to be more stable both chemically upon prolonged UV irradiation and thermally in the dark as compared with that in a PMMA film.     

Preparation of crimped synthetic fibres directly in the spinning process

Conclusions In the preparation of crimped polyamide yarns without the use of texturing devices, it has been found that in yarns of complex profile, of the head-tail type, the two parts of the yarn cross-section interact in accordance with the bimetallic plate rule. The crimp can be described satisfactorily by the Brand-Backer equation.Dependences of the degree of crimp on the ratio of the head and tail lengths, birefringence, and spinning speed have been obtained for selected variants of yarn profile; this makes it possible to find an optimum regime for yarn preparation.Translated from Khimicheskie Volokna, No. 3, pp. 32–33, May–June, 1985.     

Defensive steroids from a carrion beetle (Silpha novaboracensis)

Two novel steroids, 3,7-dihydroxy-14-pregn-4-en-15,20-dione (1) and 3,7, 20-trihydroxy-14-pregn-4-en-15-one (4), have been characterized from the rectal gland ofSilpha novaboracensis (Coleoptera: Silphidae). Judging from the function of comparable pregnanes in another species ofSilpha, the compounds may play an antipredator role.Paper No. 81 of the seriesDefense Mechanisms of Arthropods. Paper No. 80 is Eisner, T., Deyrup, M., Jacobs, R., and Meinwald, J.,J. Chem. Ecol. 12:1407–1415.     

The aqueous thermal polycondensation of asparagine and isoasparagine and the structure of polyaspartic acid

Summary Both asparagine and isoasparagine were converted into polyaspartic acids by refluxing the corresponding aqueous solutions at neutral pH in the presence of a salt. The properties of the resulting polyaspartic acids were studied. The dissociation behavior of the carboxyl groups in the polypeptides were studied by the potentiometric titration. The analysis of the titrational data was performed by a modified Speakman's method. The analysis show that both polyaspartic acids prepared from asparagine and isoasparagine have - and -aspartyl residues and the ratio of - and -aspartyl residues is 75 2585 15. A possible mechanism for the formation of - and -aspartyl residues in the polymer was discussed.     

Structure of the Reaction Zone of a Steady Detonation Wave in Dinitrodiazapentane

The massvelocity profiles in 2,4dinitro2,4diazapentane samples of different densities were registered by a laser interferometer and the electromagnetic technique. The reaction time was shown to reach 300 nsec and weakly depend on density, while the pressure in the chemical spike can be twice as high as that at the Chapman–Jouguet point. No special features due to diamond formation were observed in the massvelocity profiles registered in the chemical reaction zone.     

Vapor‐phase synthesis of acetophenone in benzene acylation over CeHZSM‐5(30) zeolite

The benzene acylation was carried out with acetic anhydride as an acylating agent in vapor phase over HZSM5, Si/Al =30 and 280, HY and Ce, Vmodified HZSM5(30) zeolite catalysts at atmospheric pressure. The yield of acylated product acetophenone was found to be 82.1 wt% with 95.0% selectivity at 86.4 wt% conversion of acetic anhydride over Cemodified HZSM5(30) where Brønsted acidic sites are active for this reaction.     

Heterogeneous asymmetric reactions. 23. Enantioselective hydrogenation of ethyl pyruvate over cinchonine- and α-isocinchonine-modified platinum catalysts

The enantioselective hydrogenation of ethyl pyruvate to (S)-ethyl lactate over cinchonine- and -isocinchonine-modified Pt/Al₂O₃ catalysts was studied as a function of modifier concentration and reaction temperature. The maximum enantioselectivities obtained under the applied mild conditions were 89% ee using cinchonine (0.014 mmoldm^–3, 1 bar H₂, 23°C, 6% AcOH in toluene), and 76% ee in the case of -isocinchonine (0.14 mmoldm^–3, 1 bar H₂, –10°C, 6% AcOH in toluene). Since -isocinchonine of rigid structure exists only in anti-open conformation these data provide additional experimental evidence to support the former suggestion concerning the dominating role of anti-open conformation in these cinchona-modified enantioselective hydrogenations.     

Synthesis and polymerization of 2-(β-N-3′-halogencarbazolylethyl)-2-oxazolines

Summary The synthesis of three novel oxazoline monomers,all of which contain 3-halogen substituted carbazolyl groups [i.e., 2-(-N-3 chlorocarbazolylethyl)-2-oxazoline, 2-(-N-3 bromocarbazolylethyl)-2-oxazoline and 2-(-N-3 iodocarbazolylethyl)-2-oxazoline]and their polymerization is described.     

Highly active rare earth catalysts for the solution polymerization of ε-caprolactone

Summary By using -butyrolactone (-BL) as the reaction media, highly active catalysts--light rare earth chloride-epoxidy---BL-for the solution polymerization of -caprolactone, have been obtained for the first time. With these catalyst, PCL with molecular weight as his as 40x10⁴(Mv) can be prepared at 60°C for 1.5 hr. The amount of epoxide in catalyst solution, catalyst aging temperature and time affect the catalyst activity significantly. The mechanism study shows that in -BL, the weakening of Ln-Cl bonds by the donation of coordinated -BL with Ln³⁺ and the homogenous effect promote the reaction between light rare earth chloride and epoxide. The produced rare earth alkoxide initiates CL polymerization via a coordination-insertion mechanism with Acyl-oxygen bond cleavage.     

Textural and structural studies on nickel hydroxide electrodes. II. Turbostratic nickel (II) hydroxide submitted to electrochemical redox cycling

The textural and structural modifications involved in electrochemical redox cycling of turbostratic nickel (II) hydroxide has been investigated using X-ray diffraction and electron microscopy methods. It was found that during the first cycles, different phenomena compete: redox reactions which occur in the solid state, and ageing reactions via the solution. For the first galvanostatic charge performed at the C/5 rate in 4.5 N KOH, the direct oxidation of (II) to (III) and the ageing of (II) to (II) via the solution followed by the oxidation to (III) are in competition. The study of the discharge mechanism shows that the direct reduction (III)(II) is parallel to the reduction (III)(II) and the ageing of the turbostratic hydroxide via the solution. After the first cycle it was established that the alpha-generated (II) active phase consisted of a mixture of two kinds of particles, the oxidation of which follows two paths: (II)/(III) for the thicker particles and for the thinner (II)/(III), but these latter (II) particles aged via the solution by Oswald ripening and the (II)/(III) couples swung to (II)/(III).