Biodegradable Poly(ε‐Caprolactone)‐Based Graft Copolymers Via Poly(Linoleic Acid): In Vitro Enzymatic Evaluation

Well‐defined graft copolymers based on poly(ε‐caprolactone) (PCL) via poly(linoleic acid) (PLina), are derived from soybean oil. Poly(linoleic acid)‐g‐poly(ε‐caprolactone) (PLina‐g‐PCL) and poly(linoleic acid)‐g‐poly(styrene)‐g‐poly(ε‐caprolactone) (PLina‐g‐PSt‐g‐PCL) were synthesized by ring‐opening polymerization of ε‐caprolactone initiated by PLina and one‐pot synthesis of graft copolymers, and by ring‐opening polymerization and free radical polymerization by using PLina, respectively. PLina‐g‐PCL, PLina‐g‐PSt‐g‐PCL3, and PLina‐g‐PSt‐g‐PCL4 copolymers containing 96.97, 75.04 and 80.34 mol% CL, respectively, have been investigated regarding their enzymatic degradation properties in the presence of Pseudomonas lipase. In terms of weight loss, after 1 month, 51.5 % of PLina‐g‐PCL, 18.8 % of PLina‐g‐PSt‐g‐PCL3, and 38.4 % of PLina‐g‐PSt‐g‐PCL4 were degraded, leaving remaining copolymers with molecular weights of 16,140, 83,220 and 70,600 Da, respectively. Introducing the PLina unit into the copolymers greatly decreased the degradation rate. The molar ratio of [CL]/[Lina] dramatically decreased, from 21.3 to 8.4, after 30 days of incubation. Moreover, reduced PCL content in PLina‐g‐PSt‐g‐PCL copolymers decreased the degradation rate, probably due to the PSt enrichment within the structure, which blocks lipase contact with PCL units. Thus, copolymerization of PCL with PLina and PSt units leads to a controllable degradation profile, which encourages the use of these polymers as promising biomaterials for tissue engineering applications.     

Part 7. Effects of poly(L‐lactide‐co‐ϵ‐caprolactone) on morphology,structure, crystallization,and physical properties of blends of poly(L‐lactide) and poly(ϵ‐caprolactone)

Blended films of poly(L ‐lactide) [ie poly(L ‐lactic acid)] (PLLA) and poly(?‐caprolactone) (PCL) without or mixed with 10 wt% poly(L ‐lactide‐co‐?‐caprolactone) (PLLA‐CL) were prepared by solution‐casting. The effects of PLLA‐CL on the morphology, phase structure, crystallization, and mechanical properties of films have been investigated using polarization optical microscopy, scanning electron microscopy, differential scanning calorimetry and tensile testing. Addition of PLLA‐CL decreased number densities of spherulites in PLLA and PCL films, and improved the observability of spherulites and the smoothness of cross‐section of the PLLA/PCL blend film. The melting temperatures (T_m) of PLLA and PCL in the films remained unchanged upon addition of PLLA‐CL, while the crystallinities of PLLA and PCL increased at PLLA contents [X_PLLA = weight of PLLA/(weight of PLLA and PCL)] of 0.4–0.7 and at most of the X_PLLA values, respectively. The addition of PLLA‐CL improved the tensile strength and the Young modulus of the films at X_PLLA of 0.5–0.8 and of 0–0.1 and 0.5–0.8, respectively, and the elongation at break of the films at all the X_PLLA values. These findings strongly suggest that PLLA‐CL was miscible with PLLA and PCL, and that the dissolved PLLA‐CL in PLLA‐rich and PCL‐rich phases increased the compatibility between these two phases. © 2003 Society of Chemical Industry     

Crystallization behavior of poly(ϵ‐caprolactone) in poly(ϵ‐caprolactone) and poly(vinyl methyl ether) mixtures

The morphological development and crystallization behavior of poly(?‐caprolactone) (PCL) in miscible mixtures of PCL and poly(vinyl methyl ether) (PVME) were investigated by optical microscopy as a function of the mixture composition and crystallization temperature. The results indicated that the degree of crystallinity of PCL was independent of the mixture composition upon melt crystallization because the glass‐transition temperatures of the mixtures were much lower than the crystallization temperature of PCL. The radii of the PCL spherulites increased linearly with time at crystallization temperatures ranging from 42 to 49°C. The isothermal growth rates of PCL spherulites decreased with the amount of the amorphous PVME components in the mixtures. Accounting for the miscibility of PCL/PVME mixtures, the radial growth rates of PCL spherulites were well described by a kinetic equation involving the Flory–Huggins interaction parameter and the free energy for the nuclei formation in such a way that the theoretical calculations were in good agreement with the experimental data. From the analysis of the equilibrium melting point depression, the interaction energy density of the PVME/PCL system was calculated to be ?3.95 J/cm³. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Morphology and Crystalline Structure of Poly(ε‐Caprolactone) Nanofiber via Porous Aluminium Oxide Template

Summary: Poly(ε‐caprolactone) (PCL) nanofibers with a dimension of about 150 nm were successfully fabricated by using a process of extruding PCL solution via a porous aluminium oxide template and then solidifying in methanol. The morphology, melting behavior and crystalline structure of the nanofibers were investigated by using scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and X‐ray diffraction (XRD). The results revealed that the weight‐average molecular weight ( ) of PCL hardly influenced the morphology of the nanofibers. However, the melting temperature (T_m) of the PCL crystalline increased slightly from 55.4 to 57.5 °C with an increase in . The accessional pressure and the presence of the porous template played an important role in the improvement of the orientation and crystallization structures of the polymer chains when they were passing through the nano‐scale porous channel, leading to the conglomeration of the fiber and the much larger diameter than those from the pressure‐induced extrusion process. Furthermore, comparing the processes with and without accessional pressure, the crystallinity of the nanofibers obtained under 0.2 MPa pressure increased, and the diffraction for the (001) lattice plane occurred.

SEM image of PCL nanofibers extruded via a porous aluminium oxide template with the aid of pressure.     

Fabrication and Physical Properties of Poly(ε‐Caprolactone)/Modified Graphene Nanocomposite

A chemical strategy is attempted to modify graphene for its facilitated dispersion in poly(ε‐caprolactone) (PCL) matrix. Herein, graphite oxide is subjected to sequential treatment with phenyl isocyanate and vitamin C (VC) to yield graphene nanosheets (iG‐VC). It is noteworthy that following the reduction treatment, iG‐VC graphene sheets exfoliate within the PCL matrix and show appreciable interfacial compatibility with PCL matrix in organic solvent by virtue of improved polarity from isocyanate treatment. The tensile yield strength and Young's modulus of the PCL/iG‐VC composite exhibit pronounced enhancement as compared to neat PCL, despite of mere composition of graphene sheets. The tensile yield stress of composite is increased notably to reach 18.6 MPa at 3 wt% graphene sheets as compared to neat PCL. Likewise, Young's modulus of composite is observed to increase from 370 to 470 MPa at 5 wt% graphene sheets. Moreover, the crystallization temperature (T _c) and crystallinity of PCL increase significantly upon incorporation of small amount of iG‐VC. Ultimately, functional role of iG‐VC graphene sheets is demonstrated in enhancing electrical conductivity of PCL‐based nanocomposites. The plausible mechanisms are also proposed to explain the increased T _c, improved mechanical property, and improved electrical conductivity of PCL/iG‐VC composite.

     

Synthesis of poly(ester‐anhydride)s based on poly(ϵ‐caprolactone) prepolymer

The objective of this study was to prepare high molecular weight poly(ester‐anhydride)s by melt polycondensation. The polymerization procedure consisted of the preparation of carboxylic acid terminated poly(?‐caprolactone) prepolymers that were melt polymerized to poly(?‐caprolactone)s containing anhydride functions along the polymer backbone. Poly(?‐caprolactone) prepolymers were prepared using either 1,4‐butanediol or 4‐(hydroxymethyl)benzoic acid as initiators, yielding hydroxyl‐terminated intermediates that were then converted to carboxylic acid‐terminated prepolymers by reaction with succinic anhydride. Prepolymers were then allowed to react with an excess of acetic anhydride, followed by subsequent polycondensation to resulting high molecular weight poly(ester‐anhydride)s. Upon coupling of prepolymers, size exclusion chromatography analyses showed an increase from 3600 to 70,000 g/mol in number‐average molecular weight (M_n) for the 1,4‐butanediol initiated polymer, and an increase from 7200 to 68,000 g/mol for the 4‐(hydroxymethyl)benzoic acid‐initiated polymer. 4‐Hydroxybenzoic acid and adipic acid were also used as initiators in the preparation of poly(?‐caprolactone) prepolymers. However, with these initiators, the results were not satisfactory. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 176–185, 2001     

Synthesis and characterization of a random terpolymer of L‐lactide, ϵ‐caprolactone and glycolide

A random terpolymer of L ‐lactide (LL), ?‐caprolactone (CL) and glycolide (G) has been synthesized in bulk at 130 °C using stannous octoate as the coordination–insertion initiator. The terpolymer, poly(LL‐ran‐CL‐ran‐G), has been characterized by a combination of analytical techniques: GPC, ¹H NMR, ¹³C NMR, DSC and TG. Molecular weight characterization by GPC shows a unimodal molecular weight distribution with values of M _n = 1.01 × 10⁵ g mol^?1 and M _w / M _n = 2.17. Compositional and microstructural analysis by ¹H NMR and ¹³C NMR, respectively, reveal a terpolymer composition of LL:CL:G = 74:15:11 (mol%) with a chain microstructure consistent with random monomer sequencing. This latter view is supported by the terpolymer temperature transitions (T_g and T_m) from DSC and the thermal decomposition profile from TG. The results and, in particular, the conclusion that it is a random rather than a statistical terpolymer are discussed in the light of current theories regarding the mechanism of this type of polymerization. © 2001 Society of Chemical Industry     

The ageing of poly(ϵ‐caprolactone)

Partially crystallized poly(?‐caprolactone) has been stored for up to 6 months at various temperatures from ?18 to 50 °C and the change in tensile properties, crystallinity and melting behaviour followed with storage time. The Young modulus, yield and drawing stress were observed to increase with time and at a rate which increased with storage temperature. These changes in tensile properties could be accounted for by the increase in crystallinity and were attributed to a thickening of the lamellae which reinforced the morphology and increased the stiffness of the polymer. The thickening of the lamellae accounted for the shift of the melting endotherms to higher temperatures with time. The stem lengths increased with the square root of the storage time and the rate increased with temperature corresponding to an activation energy of 40 ± 5 kJ mol^?1. It is considered that ageing occurred by a process of secondary crystallization by extension of the ‘fold surface’ into the adjacent melt and the thickening of the lamellae. The time dependence of growth can only be explained by small segments of the chain being incorporated onto the crystal on the time scale of the local segmental mobility which is independent of chain entanglements. This does not have the characteristics of a nucleation controlled process but is a thermally activated diffusion process the rate of which increases with temperature. © 2015 Society of Chemical Industry     

Synthesis and characterization of poly(ϵ‐caprolactone)‐b‐poly(ethylene glycol) block copolymers prepared by a salicylaldimine‐aluminum complex

A series of poly(?‐caprolactone)‐b‐poly(ethylene glycol) (PCL‐b‐PEG) block copolymers with different molecular weights were synthesized with a salicylaldimine‐aluminum complex in the presence of monomethoxy poly(ethylene glycol). The block copolymers were characterized by ¹H NMR, GPC, WAXD, and DSC. The ¹H NMR and GPC results verify the block structure and narrow molecular weight distribution of the block copolymers. WAXD and DSC results show that crystallization behavior of the block copolymers varies with the composition. When the PCL block is extremely short, only the PEG block is crystallizable. With further increase in the length of the PCL block, both blocks can crystallize. The PCL crystallizes prior to the PEG block and has a stronger suppression effect on crystallization of the PEG block, while the PEG block only exerts a relatively weak adverse effect on crystallization of the PCL block. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

A comparative study of poly(l‐lactide)‐block‐poly(ϵ‐caprolactone) six‐armed star diblock copolymers and polylactide/poly(ϵ‐caprolactone) blends

This paper deals with the synthesis of a series of six‐armed star diblock copolymers based on poly(l ‐lactide) (PLLA) and poly(?‐caprolactone) (PCL) by ring‐opening polymerization using stannous octoate as catalyst and the preparation of polylactide (PLA)/PCL linear blends using a solution blending technique, while keeping the PLA‐to‐PCL ratio comparable in both systems. The thermal, rheological and mechanical properties of the copolymers and the blends were comparatively studied. The melting point and the degree of crystallinity were found to be lower for the copolymers than the blends due to poor folding property of star copolymers. Dynamic rheology revealed that the star polymers have lower elastic modulus, storage modulus and viscosity as compared to the corresponding blends with similar composition. The blends show two‐phase dispersed morphology whereas the copolymers exhibited microphase separated morphology with elongated (worm‐like) microdomains. The crystalline structures of the copolymers were characterized by larger crystallites than their blend counterparts, as estimated using Sherrer's equation based on wide‐angle X‐ray diffraction data. © 2016 Society of Chemical Industry     

Preparation of poly(ε‐caprolactone)/poly(ε‐caprolactone‐co‐lactide) (PCL/PLCL) blend filament by melt spinning

Poly(ε‐caprolactone)/poly(ε‐caprolactone‐co‐lactide) (PCL/PLCL) blend filaments with various ratios of PCL and PLCL were prepared by melt spinning. The effect of PLCL content on the physical properties of the blended filament was investigated. The melt spinning of the blend was carried out and the as spun filament was subsequently subjected to drawing and heat setting process. The addition of PLCL caused significant changes in the mechanical properties of the filaments. Crystallinity of blend decreased with the addition of PLCL as observed by X‐ray diffraction (XRD) and differential scanning calorimetry (DSC). Scanning electron microscopy (SEM) revealed that the fracture surface becomes rougher at higher PLCL content. It may be proposed that PCL and PLCL show limited interaction within the blend matrix. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Confined crystallization morphology of poly(ϵ‐caprolactone) block within poly(ϵ‐caprolactone)–poly(l‐lactide) copolymers

The confined crystallization of poly(?‐caprolactone) (PCL) block in poly(?‐caprolactone)–poly(l ‐lactide) (PCL‐PLLA) copolymers was investigated using differential scanning calorimetry, polarized optical microscopy, scanning electronic microscopy and atomic force microscopy. To study the effect of crystallization and molecular chain motion state of PLLA blocks in PCL‐PLLA copolymers on PCL crystallization morphology, high‐temperature annealing (180 °C) and low‐temperature annealing (80 °C) were applied to treat the samples. It was found that the crystallization morphology of PCL block in PCL‐PLLA copolymers is not only related to the ratio of block components, but also related to the thermal history. After annealing PCL‐PLLA copolymers at 180 °C, the molten PCL blocks are rejected from the front of PLLA crystal growth into the amorphous regions, which will lead to PCL and PLLA blocks exhibiting obvious fractionated crystallization and forming various morphologies depending on the length of PLLA segment. On the contrary, PCL blocks more easily form banded spherulites after PCL‐PLLA copolymers are annealed at 80 °C because the preexisting PLLA crystal template and the dangling amorphous PLLA chains on PCL segments more easily cause unequal stresses at opposite fold surfaces of PCL lamellae during the growth process. Also, it was found that the growth rate of banded spherulites is less than that of classical spherulites and the growth rate of banded spherulites decreases with decreasing band spacing. © 2019 Society of Chemical Industry     

Preparation and characterization of biodegradable poly(ϵ‐caprolactone) self‐reinforced composites and their crystallization behavior

Self‐reinforced poly(?‐caprolactone) (PCL) composites were prepared by dispersing a homologous nucleating agent within the PCL matrix through melt mixing. Coalesced PCL, featuring more orderly chain arrangements, acted as the nucleating agent leading to improvement of crystallization for the melt PCL matrix. Non‐isothermal melt crystallization behavior, isothermal melt crystallization kinetics, spherulitic morphology and the crystal structure of neat PCL and the PCL self‐reinforced composites were studied in detail. The results indicated that both non‐isothermal and isothermal melt crystallization of PCL composites were enhanced significantly by the homologous nucleating agent, while the crystallization mechanism and crystal structures remained unchanged. The results of tensile mechanical tests showed that the Young's modulus of the composites was improved by up to 77% with the incorporation of 20 wt% nucleating agent. Biocompatibility tests demonstrated that the cells could adhere to and proliferate well on the surface of the self‐reinforced PCL composites. © 2017 Society of Chemical Industry     

Poly(vinyl pyrrolidone‐co‐vinyl acetate)‐graft‐poly(ε‐caprolactone) as a compatibilizer for cellulose acetate/poly(ε‐caprolactone) blends

Poly(vinyl pyrrolidone‐co‐vinyl acetate)‐graft‐poly(ε‐caprolactone) (PVPVAc‐g‐PCL) was synthesized by radical copolymerization of N‐vinyl‐2‐pyrrolidone (VP)/vinyl acetate (VAc) comonomer and PCL macromonomer containing a reactive 2‐hydroxyethyl methacrylate terminal. The graft copolymer was designed in order to improve the interfacial adhesiveness of an immiscible blend system composed of cellulose acetate/poly(ε‐caprolactone) (CA/PCL). Adequate selections of preparation conditions led to successful acquisition of a series of graft copolymer samples with different values of molecular weight ( ), number of grafts (n), and segmental molecular weight of PVPVAc between adjacent grafts (M_n (between grafts)). Differential scanning calorimetry measurements gave a still immiscible indication for all of the ternary blends of CA/PCL/PVPVAc‐g‐PCL (72 : 18 : 10 in weight) that were prepared by using any of the copolymer samples as a compatibilizer. However, the incorporation enabled the CA/PCL (4 : 1) blend to be easily melt‐molded to give a visually homogeneous film sheet. This compatibilizing effect was found to be drastically enhanced when PVPVAc‐g‐PCLs of higher and M_n (between grafts) and lower n were employed. Scanning electron microscopy revealed that a uniform dispersion of the respective ingredients in the ternary blends was attainable with an assurance of the mixing scale of several hundreds of nanometers. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Kinetics of microwave‐assisted polymerization of ϵ‐caprolactone

The kinetics of polymerization of ?‐caprolactone (CL) in bulk was studied by irradiating with microwave of 350 W and frequency of 2.45 GHz with different cycle‐heating periods (30–50 s). The molecular weight distributions were determined as a function of reaction time by gel permeation chromatography. Because the temperature of the system continuously varied with reaction time, a model based on continuous distribution kinetics with time/temperature‐dependent rate coefficients was proposed. To quantify the effect of microwave on polymerization, experiments were conducted under thermal heating. The polymerization was also investigated with thermal and microwave heating in the presence of zinc catalyst. The activation energies determined from temperature‐dependent rate coefficients for pure thermal heating, thermally aided catalytic polymerization, and microwave‐aided catalytic polymerization were 24.3, 13.4, and 5.7 kcal/mol, respectively. This indicates that microwaves increase the polymerization rate by lowering the activation energy. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1450–1456, 2004     

Synthesis and Characterization of Biodegradable Poly(ε‐caprolactone)‐Polyglycolide‐Poly(ethylene glycol) Monomethyl Ether Random Copolymer

Summary: Poly(ε‐caprolactone)‐polyglycolide‐poly(ethylene glycol) monomethyl ether random copolymers were synthesized from ε‐caprolactone (ε‐CL), glycolide (GA) and poly(ethylene glycol) monomethyl ether (MPEG) using stannous octoate as catalyst at 160 °C by bulk polymerization. The copolymers with different composition were synthesized by adjusting the weight ration of reaction mixture. The resultant copolymer with a weight ratio (10:15:75) of MPEG2000, GA, and CL was characterized by IR, ¹H NMR, GPC and DSC. The new biodegradable copolymer has potential for medical applications since it is combined with properties of PCL, PGA and MPEG.

     

Melt electrospinning writing of three‐dimensional star poly(ϵ‐caprolactone) scaffolds

In the last decade, the melt‐electrospinning technique has gained attention for the production of highly porous microfibrous tissue engineering scaffolds. The possibility of processing polymers without the use of organic solvents is one of the main advantages over solution electrospinning. In this study, computer‐controlled melt‐electrospinning of a commercial poly(?‐caprolactone) and of two batches with different molecular weights of a three‐arm star poly(?‐caprolactone) by means of a screw‐extruder‐based additive manufacturing system is reported. Experimental parameters such as processing temperature, extrusion flow rate and applied voltage were studied and optimized in order to obtain non‐woven meshes with uniform fibre morphology. Applying the optimized parameters, three‐dimensional scaffolds were produced using a layer‐by‐layer approach (0 ? 90° lay‐down pattern). © 2013 Society of Chemical Industry     

Thermoresponsive poly(ϵ‐caprolactone)‐graft‐poly(N‐isopropylacrylamide) graft copolymers prepared by a combination of ring‐opening polymerization and sequential azide–alkyne click chemistry

A straightforward strategy is described to synthesize poly(?‐caprolactone)‐graft‐poly(N‐isopropylacrylamide) (PCL‐g‐PNIPAAm) amphiphilic graft copolymers consisting of potentially biodegradable polyester backbones and thermoresponsive grafting chains. PCL with pendent chlorides was prepared by ring‐opening polymerization, followed by conversion of the pendent chlorides to azides. Alkyne‐terminated PNIPAAm was synthesized by atom transfer radial polymerization. Then, the alkyne end‐functionalized PNIPAAm was grafted onto the PCL backbone by a copper‐catalyzed azide–alkyne cycloaddition. PCL‐g‐PNIPAAm graft copolymers self‐assembled into spherical micelles comprised of PCL cores and PNIPAAm coronas. The critical micelle concentrations of the graft copolymers were in the range 7.8–18.2 mg L^?1, depending on copolymer composition. Mean hydrodynamic diameters of micelles were in the range 65–135 nm, which increased as the length of grafting chains grew. PCL‐g‐PNIPAAm micelles were thermosensitive and aggregated upon heating. © 2014 Society of Chemical Industry     

Ring‐banded spherulites in poly(ϵ‐caprolactone) blended with hydroxyethyl cellulose acetate as an indication for partial miscibility

The morphologies of poly(?‐caprolactone) (PCL) blends with hydroxyethyl cellulose acetate (HECA), a thermotropic liquid crystalline polymer (TLCP), were investigated by optical microscopy. It is demonstrated that when the pure PCL is crystallized from the melt, a spherulitic morphology arises with distinct Maltese crosses. With the addition of the HECA, the spherulites of the PCL/HECA blends show not only the Maltese crosses but also distinct extinction rings (i.e., a ring‐banded spherulitic morphology). The average periodic distance of the extinction rings decreases drastically with the increase of the HECA content from 0.5 to 5 wt % in the mixture, whereas it decreases only slightly with the further increase of HECA. The periodicity of extinction rings is also influenced by the crystallization temperature. The formation of the ring‐banded spherulites of PCL in PCL/HECA blends is explained in terms of stress‐induced twisted lamellar crystallization and used as an indication of the molecular solubility of the HECA in the PCL. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1681–1686, 2001     

Synthesis and characterization of fullerene grafted poly(ε‐caprolactone)

The fullerene grafted poly(ε‐caprolactone) (PCL) was successfully synthesized with a graft efficiency of 80%. The fullerene moieties grafted onto the PCL chain aggregate into 1–2 μm particles so that a physical pseudo‐network is formed. Because of the existence of the network structure, the fullerene grafted PCL film can retain its shape at much higher temperatures than that of pure PCL film, as observed in dynamic mechanical tests. It shows a hydrophobic gelling behavior in chloroform solution. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008