Conjugated Polymers of Intrinsic Microporosity (C‐PIMs)

Conjugated microporous polymers (CMPs) have shown great potential for energy and environmental issues, however, poor solubility and processability of most of these materials limit their applications. Herein, a range of linear conjugated polymers of intrinsic microporosity (C‐PIMs) is reported, combining for the first time the properties of conjugated microporous polymers, such as tunable electronic properties and compositional variation, with those of linear polymers of intrinsic microporosity (PIMs) allowing for solution processability and film formation. These soluble materials have a number of potential applications, for example as components in devices where large, porous interfaces are combined with extended electronic conjugation.     

Enhanced Electrochemical CO2 Reduction of Cu@CuxO Nanoparticles Decorated on 3D Vertical Graphene with Intrinsic sp3‐type Defect

Defective 3D vertical graphene (VG) with a relatively large surface area, high defect density, and increased surface electrons is synthesized via a scalable plasma enhanced chemical vapor deposition method, together with a postsynthesis Ar‐plasma treatment (VG‐Ar). Subsequently, Cu@Cu_xO nanoparticles are deposited onto VG‐Ar (Cu/VG‐Ar) through a galvanostatic pulsed electrodeposition method. These Cu@Cu_xO nanocatalyst systems exhibit a superior electrochemical CO₂ reduction performance when compared to Cu‐based catalysts supported on commercial graphene paper or pristine VG without postsynthesis Ar‐plasma treatment. The Cu/VG‐Ar achieves the highest CO₂ reduction Faradaic efficiency of 60.6% (83.5% of which are attributed to liquid products, i.e., formate, ethanol, and n‐propanol) with a 5.6 mA cm^?2 partial current density at ?1.2 V versus reversible hydrogen electrode (RHE). The improved CO₂ reduction performance of Cu/VG‐Ar originates from the well‐dispersed Cu@Cu_xO nanoparticles deposited on the defective VG‐Ar. The intrinsic carbon defects on VG‐Ar can suppress the hydrogen evolution reaction as well as tune the interaction between VG and Cu@Cu_xO, thus impeding the excessive oxidation of Cu₂O species deposited on VG‐Ar. The defective VG‐Ar and stabilized Cu@Cu_xO enhances CO₂ adsorption and promotes electron transfer to the adsorbed CO₂ and intermediates on the catalyst surface, thus improving the overall CO₂ reduction performance.     

Oxidation‐Resistant and Elastic Mesoporous Carbon with Single‐Layer Graphene Walls

An oxidation‐resistant and elastic mesoporous carbon, graphene mesosponge (GMS), is prepared. GMS has a sponge‐like mesoporous framework (mean pore size is 5.8 nm) consisting mostly of single‐layer graphene walls, which realizes a high electric conductivity and a large surface area (1940 m² g^?1). Moreover, the graphene‐based framework includes only a very small amount of edge sites, thereby achieving much higher stability against oxidation than conventional porous carbons such as carbon blacks and activated carbons. Thus, GMS can simultaneously possess seemingly incompatible properties; the advantages of graphitized carbon materials (high conductivity and high oxidation resistance) and porous carbons (large surface area). These unique features allow GMS to exhibit a sufficient capacitance (125 F g^?1), wide potential window (4 V), and good rate capability as an electrode material for electric double‐layer capacitors utilizing an organic electrolyte. Hence, GMS achieves a high energy density of 59.3 Wh kg^?1 (material mass base), which is more than twice that of commercial materials. Moreover, the continuous graphene framework makes GMS mechanically tough and extremely elastic, and its mean pore size (5.8 nm) can be reversibly compressed down to 0.7 nm by simply applying mechanical force. The sponge‐like elastic property enables an advanced force‐induced adsorption control.     

Carbide‐Derived Carbons – From Porous Networks to Nanotubes and Graphene

Carbide‐derived carbons (CDCs) are a large family of carbon materials derived from carbide precursors that are transformed into pure carbon via physical (e.g., thermal decomposition) or chemical (e.g., halogenation) processes. Structurally, CDC ranges from amorphous carbon to graphite, carbon nanotubes or graphene. For halogenated carbides, a high level of control over the resulting amorphous porous carbon structure is possible by changing the synthesis conditions and carbide precursor. The large number of resulting carbon structures and their tunability enables a wide range of applications, from tribological coatings for ceramics, or selective sorbents, to gas and electrical energy storage. In particular, the application of CDC in supercapacitors has recently attracted much attention. This review paper summarizes key aspects of CDC synthesis, properties, and applications. It is shown that the CDC structure and properties are sensitive to changes of the synthesis parameters. Understanding of processing–structure–properties relationships facilitates tuning of the carbon material to the requirements of a certain application.     

Graphene: Carbide‐Derived Carbons – From Porous Networks to Nanotubes and Graphene (Adv. Funct. Mater. 5/2011)

Carbide‐derived carbons (CDCs) are a large family of carbon materials derived from carbide precursors that are transformed into pure carbon via physical (e.g., thermal decomposition) or chemical (e.g., halogenation) processes. Structurally, CDC ranges from amorphous carbon to graphite, carbon nanotubes or graphene. For halogenated carbides, a high level of control over the resulting amorphous porous carbon structure is possible by changing the synthesis conditions and carbide precursor. The large number of resulting carbon structures and their tunability enables a wide range of applications, from tribological coatings for ceramics, or selective sorbents, to gas and electrical energy storage. In particular, the application of CDC in supercapacitors has recently attracted much attention. This review paper summarizes key aspects of CDC synthesis, properties, and applications. It is shown that the CDC structure and properties are sensitive to changes of the synthesis parameters. Understanding of processing–structure–properties relationships facilitates tuning of the carbon material to the requirements of a certain application.     

Regulating Top‐Surface Multilayer/Single‐Crystal Graphene Growth by “Gettering” Carbon Diffusion at Backside of the Copper Foil

A unique strategy is reported to constrain the nucleation centers for multilayer graphene (MLG) and, later, single‐crystal graphene domains by gettering carbon source on backside of the flat Cu foil, during chemical vapor deposition. Hitherto, for a flat Cu foil, the top‐surface‐based growth mechanism is emphasized, while overlooking the graphene on the backside. However, the systematic experimental findings indicate a strong correlation between the backside graphene and the nucleation centers on the top‐surface, governed by the carbon diffusion through the bulk Cu. This understanding steers to devise a strategy to mitigate the carbon diffusion to the top‐surface by using a carbon “getter” substrate, such as nickel, on the backside of the Cu foil. Depth profiling of the nickel substrate, along with the density functional theory calculations, verifies the gettering role of the nickel support. The implementation of the backside carbon gettering approach on single‐crystal graphene growth results in lowering the nucleation density by two orders of magnitude. This enables the single‐crystal domains to grow by 6 mm laterally on the untreated Cu foil. Finally, the growth of large‐area polycrystalline single layer graphene, free of unwanted MLG domains, with significantly improved field‐effect mobility of ≈6800 cm² V^?1 s^?1 is demonstrated.     

Ultra‐High Surface Area Nitrogen‐Doped Carbon Aerogels Derived From a Schiff‐Base Porous Organic Polymer Aerogel for CO2 Storage and Supercapacitors

Nitrogen‐doped carbon aerogels (NCAs) have received great attention for a wide range of applications, from thermal electronics to waste water purification, heavy metal or gas adsorption, energy storage, and catalyst supports. Herein NCAs are developed via the synthesis of a Schiff‐base porous organic polymer aerogel followed by pyrolysis. By controlling the pyrolysis temperature, the polymer aerogel can be simply converted into porous NCAs with a low bulk density (5 mg cm^?3), high surface area (2356 m² g^?1), and high bulk porosity (70%). The NCAs containing 1.8–5.3 wt% N atoms exhibit remarkable CO₂ uptake capacities (6.1 mmol g^?1 at 273 K and 1 bar, 33.1 mmol g^?1 at 323 K and 30 bar) and high ideal adsorption solution theory selectivity (47.8) at ambient pressure. Supercapacitors fabricated with NCAs display high specific capacitance (300 F g^?1 at 0.5 A g^?1), fast rate (charge to 221 F g^?1 within only 17 s), and high stability (retained >98% capacity after 5000 cycles). Asymmetric supercapacitors assembled with NCAs also show high energy density and power density with maximal values of 30.5 Wh kg^?1 and 7088 W kg^?1, respectively. The outstanding CO₂ uptake and energy storage abilities are attributed to the ultra‐high surface area, N‐doping, conductivity, and rigidity of NCA frameworks.     

Enhanced Interfacial Stability of Hybrid‐Electrolyte Lithium‐Sulfur Batteries with a Layer of Multifunctional Polymer with Intrinsic Nanoporosity

The use of lithium‐ion conductive solid electrolytes offers a promising approach to address the polysulfide shuttle and the lithium‐dendrite problems in lithium‐sulfur (Li‐S) batteries. One critical issue with the development of solid‐electrolyte Li‐S batteries is the electrode–electrolyte interfaces. Herein, a strategic approach is presented by employing a thin layer of a polymer with intrinsic nanoporosity (PIN) on a Li⁺‐ion conductive solid electrolyte, which significantly enhances the ionic interfaces between the electrodes and the solid electrolyte. Among the various types of Li⁺‐ion solid electrolytes, NASICON‐type Li_1+xAl_xTi_2‐x(PO₄)₃ (LATP) offers advantages in terms of Li⁺‐ion conductivity, stability in ambient environment, and practical viability. However, LATP is susceptible to reaction with both the Li‐metal anode and polysulfides in Li‐S batteries due to the presence of easily reducible Ti⁴⁺ ions in it. The coating with a thin layer of PIN presented in this study overcomes the above issues. At the negative‐electrode side, the PIN layer prevents the direct contact of Li‐metal with the LATP solid electrolyte, circumventing the reduction of LATP by Li metal. At the positive electrode side, the PIN layer prevents the migration of polysulfides to the surface of LATP, preventing the reduction of LATP by polysulfides.     

Electrically Heatable Graphene Aerogels as Nanoparticle Supports in Adsorptive Desulfurization and High‐Pressure CO2 Capture

Reduced‐graphene‐oxide (rGO) aerogels provide highly stabilising, multifunctional, porous supports for hydrotalcite‐derived nanoparticles, such as MgAl‐mixed‐metal‐oxides (MgAl‐MMO), in two commercially important sorption applications. Aerogel‐supported MgAl‐MMO nanoparticles show remarkable enhancements in adsorptive desulfurization performance compared to unsupported nanoparticle powders, including substantial increases in organosulfur uptake capacity (>100% increase), sorption kinetics (>30‐fold), and nanoparticle regeneration stability (>3 times). Enhancements in organosulfur capacity are also observed for aerogel‐supported NiAl‐ and CuAl‐metal‐nanoparticles. Importantly, the electrical conductivity of the rGO aerogel network adds completely new functionality by enabling accurate and stable nanoparticle temperature control via direct electrical heating of the graphitic support. Support‐mediated resistive heating allows for thermal nanoparticle recycling at much faster heating rates (>700 °C?min^?1) and substantially reduced energy consumption, compared to conventional, external heating. For the first time, the CO₂ adsorption performance of MgAl‐MMO/rGO hybrid aerogels is assessed under elevated‐temperature and high‐CO₂‐pressure conditions relevant for pre‐combustion carbon capture and hydrogen generation technologies. The total CO₂ capacity of the aerogel‐supported MgAl‐MMO nanoparticles is more than double that of the unsupported nanoparticles and reaches 2.36 mmol·CO₂ g^?1 ads (at p_CO2 = 8 bar, T = 300 °C), outperforming other high‐pressure CO₂ adsorbents.     

CO2‐Laser‐Induced Growth of Epitaxial Graphene on 6H‐SiC(0001)

The thermal decomposition of SiC surface provides, perhaps, the most promising method for the epitaxial growth of graphene on a material useful in the electronics platform. Currently, efforts are focused on a reliable method for the growth of large‐area, low‐strain epitaxial graphene that is still lacking. Here, a novel method for the fast, single‐step epitaxial growth of large‐area homogeneous graphene film on the surface of SiC(0001) using an infrared CO₂ laser (10.6 μm) as the heating source is reported. Apart from enabling extreme heating and cooling rates, which can control the stacking order of epitaxial graphene, this method is cost‐effective in that it does not necessitate SiC pre‐treatment and/or high vacuum, it operates at low temperature and proceeds in the second time scale, thus providing a green solution to EG fabrication and a means to engineering graphene patterns on SiC by focused laser beams. Uniform, low–strain graphene film is demonstrated by scanning electron microscopy, X‐ray photoelectron spectroscopy, secondary ion‐mass spectroscopy, and Raman spectroscopy. Scalability to industrial level of the method described here appears to be realistic, in view of the high rate of CO₂‐laser‐induced graphene growth and the lack of strict sample–environment conditions.     

Highly Conductive Few‐Layer Graphene/Al2O3 Nanocomposites with Tunable Charge Carrier Type

An ex situ strategy for fabrication of graphene oxide (GO)/metal oxide hybrids without assistance of surfactant is introduced. Guided by this strategy, GO/Al₂O₃ hybrids are fabricated by two kinds of titration methods in which GO and Al₂O₃ colloids are utilized as titrant for hybrids of low and high GO content respectively. After sintered by spark plasma sintering, few‐layer graphene (FG)/Al₂O₃ nanocomposites are obtained and GO is well reduced to FG simultaneously. A percolation threshold as low as 0.38 vol.% is achieved and the electrical conductivity surpasses 10³ Sm^?1 when FG content is only 2.35 vol.% in FG/Al₂O₃ composite, revealing the homogeneous dispersion and high quality of as‐prepared FG. Furthermore, it is found that the charge carrier type changes from p‐ to n‐type as graphene content becomes higher. It is deduced that this conversion is related to the doping effect induced by Al₂O₃ matrix and is thickness‐dependent with respect to FG.     

Improved CO2 Capture from Flue Gas by Basic Sites,Charge Gradients,and Missing Linker Defects on Nickel Face Cubic Centered MOFs

The adsorptive properties of the isoreticular series [Ni₈(OH)₄(H₂O)₂(BDP_X)₆] (H₂BDP_X = 1,4‐bis(pyrazol‐4‐yl)benzene‐4‐X with X = H (1), OH (2), NH₂ (3)) can be enhanced by postsynthetic treatment with an excess of KOH in ethanol. In the case of X = H, NH₂, this treatment leads to partial removal of the organic linkers, deprotonation of coordinated water molecules and introduction of extraframework cations, giving rise to materials of K[Ni₈(OH)₅(EtO)‐(H₂O)₂(BDP_X)_5.5] (1@KOH, 3@KOH) formulation, in which the original framework topology is maintained. By contrast, the same treatment with KOH in the [Ni₈(OH)₄(H₂O)₂(BDP_OH)₆] (2) system, enclosing the more acidic phenol residues, leads to a new material containing a larger fraction of missing linker defects and extra‐framework cations as well as phenolate residues, giving rise to the material K₃[Ni₈(OH)₃(EtO)(H₂O)₆(BDP_O)₅] (2@KOH), which also conserves the original face cubic centered (fcu) topology. It is noteworthy that the introduction of missing linker defects leads to a higher accessible pore volume with a concomitant increased adsorption capacity. Moreover, the creation of coordinatively unsaturated metal centers, charge gradients, and phenolate nucleophilic sites in 2@KOH gives rise to a boosting of CO₂ capture features with increased adsorption heat and adsorption capacity, as proven by the measurement of pulse gas chromatography and breakthrough curve measurements of simulated flue gas.     

Heteroatom (N or N‐S)‐Doping Induced Layered and Honeycomb Microstructures of Porous Carbons for CO2 Capture and Energy Applications

Increasing global challenges such as climate change, environmental pollution, and energy shortage have stimulated the worldwide explorations into novel and clean materials for their applications in the capture of carbon dioxide, a major greenhouse gas, and toxic pollutants, energy conversion, and storage. In this study, two microstructured carbons, namely N‐doped pillaring layered carbon (NC) and N, S codoped honeycomb carbon (NSC), have been fabricated through a one‐pot pyrolysis process of a mixture containing glucose, sodium bicarbonate, and urea or thiourea. The heteroatom doping is found to induce tailored microstructures featuring highly interconnected pore frameworks, high sp²‐C ratios, and high surface areas. The formation mechanism of the varying pore frameworks is believed to be hydrogen‐bond interactions. NSC displays a similar CO₂ adsorption capacity (4.7 mmol g^?1 at 0 °C), a better CO₂/N₂ selectivity, and higher activity in oxygen reduction reaction as compared with NC‐3 (the NC sample with the highest N content of 7.3%). NSC favors an efficient four‐electron reduction pathway and presents better methanol tolerance than Pt/C in alkaline media. The porous carbons also exhibit excellent rate performance as supercapacitors.     

An In Situ Simultaneous Reduction‐Hydrolysis Technique for Fabrication of TiO2‐Graphene 2D Sandwich‐Like Hybrid Nanosheets: Graphene‐Promoted Selectivity of Photocatalytic‐Driven Hydrogenation and Coupling of CO2 into Methane and Ethane

A novel, in situ simultaneous reduction‐hydrolysis technique (SRH) is developed for fabrication of TiO₂‐‐graphene hybrid nanosheets in a binary ethylenediamine (En)/H₂O solvent. The SRH technique is based on the mechanism of the simultaneous reduction of graphene oxide (GO) into graphene by En and the formation of TiO₂ nanoparticles through hydrolysis of titanium (IV) (ammonium lactato) dihydroxybis, subsequently in situ loading onto graphene through chemical bonds (Ti–O–C bond) to form 2D sandwich‐like nanostructure. The dispersion of TiO₂ hinders the collapse and restacking of exfoliated sheets of graphene during reduction process. In contrast with prevenient G‐TiO₂ nanocomposites, abundant Ti³⁺ is detected on the surface of TiO₂ of the present hybrid, caused by reducing agent En. The Ti³⁺ sites on the surface can serve as sites for trapping photogenerated electrons to prevent recombination of electron–hole pairs. The high photocatalytic activity of G‐TiO₂ hybrid is confirmed by photocatalytic conversion of CO₂ to valuable hydrocarbons (CH₄ and C₂H₆) in the presence of water vapor. The synergistic effect of the surface‐Ti³⁺ sites and graphene favors the generation of C₂H₆, and the yield of the C₂H₆ increases with the content of incorporated graphene. The work may open a new doorway for new significant application of graphene for selectively catalytic C–C coupling reaction     

One‐Step Hydrothermal Synthesis of 2D Hexagonal Nanoplates of α‐Fe2O3/Graphene Composites with Enhanced Photocatalytic Activity

There has been significant progress in the field of semiconductor photocatalysis, but it is still a challenge to fabricate low‐cost and high‐activity photocatalysts because of safety issues and non‐secondary pollution to the environment. Here, 2D hexagonal nanoplates of α‐Fe₂O₃/graphene composites with relatively good distribution are synthesized for the first time using a simple, one‐step, template‐free, hydrothermal method that achieves the effective reduction of the graphene oxide (GO) to graphene and intimate and large contact interfaces of the α‐Fe₂O₃ nanoplates with graphene. The α‐Fe₂O₃/graphene composites showed significantly enhancement in the photocatalytic activity compared with the pure α‐Fe₂O₃ nanoplates. At an optimal ratio of 5 wt% graphene, 98% of Rhodamine (RhB) is decomposed with 20 min of irradiation, and the rate constant of the composites is almost four times higher than that of pure α‐Fe₂O₃ nanoplates. The decisive factors in improving the photocatalytic performance are the intimate and large contact interfaces between 2D hexagonal α‐Fe₂O₃ nanoplates and graphene, in addition to the high electron withdrawing/storing ability and the highconductivity of reduced graphene oxide (RGO) formed during the hydrothermal reaction. The effective charge transfer from α‐Fe₂O₃ nanoplates to graphene sheets is demonstrated by the significant weakening of photoluminescence in α‐Fe₂O₃/graphene composites.     

Hydrogen Selective NH2‐MIL‐53(Al) MOF Membranes with High Permeability

Hydrogen‐based energy is a promising renewable and clean resource. Thus, hydrogen selective microporous membranes with high performance and high stability are demanded. Novel NH₂‐MIL‐53(Al) membranes are evaluated for hydrogen separation for this goal. Continuous NH₂‐MIL‐53(Al) membranes have been prepared successfully on macroporous glass frit discs assisted with colloidal seeds. The gas sorption ability of NH₂‐MIL‐53(Al) materials is studied by gas adsorption measurement. The isosteric heats of adsorption in a sequence of CO₂ > N₂ > CH₄ ≈ H₂ indicates different interactions between NH₂‐MIL‐53(Al) framework and these gases. As‐prepared membranes are measured by single and binary gas permeation at different temperatures. The results of singe gas permeation show a decreasing permeance in an order of H₂ > CH₄ > N₂ > CO₂, suggesting that the diffusion and adsorption properties make significant contributions in the gas permeation through the membrane. In binary gas permeation, the NH₂‐MIL‐53(Al) membrane shows high selectivity for H₂ with separation factors of 20.7, 23.9 and 30.9 at room temperature (288 K) for H₂ over CH₄, N₂ and CO₂, respectively. In comparison to single gas permeation, a slightly higher separation factor is obtained due to the competitive adsorption effect between the gases in the porous MOF membrane. Additionally, the NH₂‐MIL‐53(Al) membrane exhibits very high permeance for H₂ in the mixtures separation (above 1.5 × 10^?6 mol m^?2 s^?1 Pa^?1) due to its large cavity, resulting in a very high separation power. The details of the temperature effect on the permeances of H₂ over other gases are investigated from 288 to 353 K. The supported NH₂‐MIL‐53(Al) membranes with high hydrogen separation power possess high stability, resistance to cracking, temperature cycling and show high reproducibility, necessary for the potential application to hydrogen recycling.     

Flexible Solid‐State Supercapacitors with Enhanced Performance from Hierarchically Graphene Nanocomposite Electrodes and Ionic Liquid Incorporated Gel Polymer Electrolyte

High energy density, durability, and flexibility of supercapacitors are required urgently for the next generation of wearable and portable electronic devices. Herein, a novel strategy is introduced to boost the energy density of flexible soild‐state supercapacitors via rational design of hierarchically graphene nanocomposite (GNC) electrode material and employing an ionic liquid gel polymer electrolyte. The hierarchical graphene nanocomposite consisting of graphene and polyaniline‐derived carbon is synthesized as an electrode material via a scalable process. The meso/microporous graphene nanocomposites exhibit a high specific capacitance of 176 F g^?1 at 0.5 A g^?1 in the ionic liquid 1‐ethyl‐3‐methylimidazolium tetrafluoroborate (EMIBF₄) with a wide voltage window of 3.5 V, good rate capability of 80.7% in the range of 0.5–10 A g^?1 and excellent stability over 10 000 cycles, which is attributed to the superior conductivity (7246 S m^?1), and quite large specific surface area (2416 m² g^?1) as well as hierarchical meso/micropores distribution of the electrode materials. Furthermore, flexible solid‐state supercapacitor devices based on the GNC electrodes and gel polymer electrolyte film are assembled, which offer high specific capacitance of 180 F g^?1 at 1 A g^?1, large energy density of 75 Wh Kg^?1, and remarkable flexible performance under consecutive bending conditions.     

Sorption‐Enhanced Mixed Matrix Membranes with Facilitated Hydrogen Transport for Hydrogen Purification and CO2 Capture

Mixed matrix membranes (MMMs) comprising size‐sieving fillers dispersed in polymers exhibit diffusivity selectivity and may surpass the upper bound for gas separation, but their performance is limited by defects at the polymer/filler interface. Herein, a fundamentally different approach employing a highly sorptive filler that is inherently less sensitive to interfacial defects is reported. Palladium nanoparticles with extremely high H₂ sorption are dispersed in polybenzimidazole at loadings near the percolation threshold, which increases both H₂ permeability and H₂/CO₂ selectivity. Performance of these MMMs surpasses the state‐of‐the‐art upper bound for H₂/CO₂ separation with polymer‐based membranes. The success of these sorption‐enhanced MMMs for H₂/CO₂ separation may launch a new research paradigm that taps the enormous knowledge of affinities between gases and nanomaterials to design MMMs for a wide variety of gas separations.     

Array of Single‐Walled Carbon Nanotube Intrajunction Devices Fabricated via Type Conversion by Partial Coating with β‐Nicotinamide Adenine Dinucleotide

The fabrication of aligned single‐walled, carbon nanotube (SWCNT) intratube junction devices by partially coating pristine SWCNTs with a β‐nicotinamide adenine dinucleotide (NADH) solution and subsequent annealing at 150 °C is reported. Gate‐bias‐dependent rectification behavior is observed with a rectification ratio of >10³ at ±1 V. A comparative study with p–n‐junction devices of randomly networked SWCNTs confirms the advantage of using aligned SWCNTs with substantially better rectifying characteristics due to the selective removal of metallic tubes by electrical breakdown. The gate dependence of the intratube p–n‐junction in the forward and backward directions is attributed to the difference in the shift of the Fermi levels (forward bias) and the enhanced direct tunneling (reverse bias), as suggested by band‐diagram modeling. This work suggests a potential application of aligned SWCNT intratube p–n‐junction devices in the future of nanoelectronic circuits.     

Enhanced Performance of I2‐Free Solid‐State Dye‐Sensitized Solar Cells with Conductive Polymer up to 6.8%

An iodine‐free solid‐state dye‐sensitized solar cell (ssDSSC) is reported here, with 6.8% energy conversion efficiency—one of the highest yet reported for N719 dye—as a result of enhanced light harvesting from the increased transmittance of an organized mesoporous TiO₂ interfacial layer and the good hole conductivity of the solid‐state‐polymerized material. The organized mesoporous TiO₂ (OM‐TiO₂) interfacial layer is prepared on large‐area substrates by a sol‐gel process, and is confirmed by scanning electron microscopy (SEM) and grazing incidence small‐angle X‐ray scattering (GISAXS). A 550‐nm‐thick OM‐TiO₂ film coated on fluorine‐doped tin oxide (FTO) glass is highly transparent, resulting in transmittance increases of 8 and 4% compared to those of the bare FTO and conventional compact TiO₂ film on FTO, respectively. The high cell performance is achieved through careful control of the electrode/hole transport material (HTM) and nanocrystalline TiO₂/conductive glass interfaces, which affect the interfacial resistance of the cell. Furthermore, the transparent OM‐TiO₂ film, with its high porosity and good connectivity, exhibits improved cell performance due to increased transmittance in the visible light region, decreased interfacial resistance ( Ω ), and enhanced electron lifetime ( τ ). The cell performance also depends on the conductivity of HTMs, which indicates that both highly conductive HTM and the transparent OM‐TiO₂ film interface are crucial for obtaining high‐energy conversion efficiencies in I₂‐free ssDSSCs.