On the effectiveness of the addition of milkweed floss fibers on processing and mechanical properties of PLA biocomposites

This study aimed at investigating the reinforcement effect of milkweed (MW) floss, a smooth and homogeneous natural fiber with a wide hollow lumen, on bio-based polymer composites. First, MW floss was thoroughly characterized in terms of morphology, surface roughness, and tensile and thermal resistance. Then, MW floss was compared to flax fibers, one of the most widely used natural fibers in the composite industry. Subsequently, bio-based composites made of polylactic acid (PLA) and 1 wt% MW floss were produced by injection molding and compared to composites reinforced with 1 wt% of flax fibers. Finally, thermal behavior, mechanical properties, and impact resistance of composites were determined. Results showed that MW floss, with respect to flax fibers, exhibits lower tensile modulus, ultimate tensile strength, surface roughness as well as a shorter critical length. Nonetheless, and despite the lower intrinsic properties of MW floss, UTS and impact resistance of MW/PLA composites were found to be 60% and 15% higher than those of Flax/PLA composites, respectively. In addition, micrographs of MW/PLA interface revealed a lack of adhesion in MW/PLA, which should be overcome by surface treatment in upcoming work.     

Physical and mechanical properties of kenaf/flax hybrid composites

This research investigates the physical and mechanical properties of hybrid composites made of epoxy reinforced by kenaf and flax natural fibers to investigate the hybridization influences of the composites. Pure and hybrid composites were fabricated using bi-directional kenaf and flax fabrics at different stacking sequences utilizing the vacuum-assisted resin infusion method. The pure and hybrid composites' physical properties, such as density, fiber volume fraction (FVF), water absorption capacity, and dimensional stability, were measured. The tests of tensile, flexural, interlaminar shear and fracture toughness (Mode II) were examined to determine the mechanical properties. The results revealed that density remained unchanged for the hybrid compared to pure kenaf/epoxy composites. The tensile, flexural, and interlaminar shear performance of flax/epoxy composite is improved by an increment of kenaf FVF in hybrid composites. The stacking sequence significantly affected the mechanical properties of hybrid composites. The highest tensile strength (59.8 MPa) was obtained for FK2 (alternative sequence of flax and kenaf fibers). However, FK3 (flax fiber located on the outer surfaces) had the highest interlaminar shear strength (12.5 MPa) and fracture toughness (3302.3 J/m²) among all tested hybrid composites. The highest water resistance was achieved for FK5 with the lowest thickness swelling.     

Flax fiber‐reinforced polylactide stereocomplex composites with enhanced heat resistance and mechanical properties

Polylactide stereocomplex (sc‐PLA) prepared by blending equivalent proportion of poly(l ‐lactic acid)/poly(d ‐lactic acid) (PLLA/PDLA) and its composites reinforced with 10, 20, and 30% flax fibers were fabricated by melt compounding and followed by injection molding. The mechanical properties, crystallinity, cross‐section morphology, and heat resistance of sc‐PLA and flax/sc‐PLA composites were compared. The results showed that homocrystallites (hc) and stereocomplex crystallites (sc) were formed simultaneously in sc‐PLA and its composites, with a melting temperature at ∼170 and ∼210°C, respectively. The crystallinity and sc content of composite increased with the increasing content of the flax fibers. The sc content of 30% flax/sc‐PLA composite could reach 98.4%, 32% higher than that of sc‐PLA (66.4%). When compared with nonblended PLLA, heat resistance of sc‐PLA increased slightly, but at the expense of mechanical properties. By the addition of flax fibers, the mechanical properties of flax/sc‐PLA composite improved significantly. The highest tensile strength, Young's modulus, and notched Izod impact strength of flax/sc‐PLA composite were 52.90 MPa, 6.42 GPa, and 5.27 kJ/m², respectively, improved by 54, 132, and 343% when compared with sc‐PLA. Moreover, the heat resistance of composite was also improved greatly by reinforcing with flax fibers. The Vicat softening temperature of 30% flax/sc‐PLA composite could achieve 162.5°C, nearly 100°C higher than that of PLLA. POLYM. COMPOS., 38:472–478, 2017. © 2015 Society of Plastics Engineers     

Influence of alkali treatment on flax fiber for use as reinforcements in polylactide stereocomplex composites

The flax and equivalent proportion of poly(l ‐lactic acid)/poly(d ‐lactic acid) (PLLA/PDLA) were melt compounded and injection molded to prepare flax‐reinforced polylactide stereocomplex (sc‐PLA) bio‐composite, and the effect of alkali treatment on the structure and properties of flax as well as the flax/sc‐PLA composite was investigated. SEM and FTIR results showed hemicellulose in flax was almost completely removed after alkali treatment and the treated flax (ALK‐flax) bundles were more separated with a cleaner surface than untreated flax (UN‐flax). DSC results showed homo‐crystallites (hc, T_m = 160–170°C) and stereocomplex crystallites (sc, T_m ～210°C) coexisted in sc‐PLA and flax/sc‐PLA composites. Compared with sc‐PLA, the total crystallinity and sc‐crystallinity of flax/sc‐PLA composite increased regardless of whether the flax were treated with alkali, whereas ALK‐flax/sc‐PLA composite showed a little higher crystallinity than UN‐flax/sc‐PLA composite. TGA results confirmed ALK‐flax/sc‐PLA composite had a higher thermal degradation temperature than UN‐flax/sc‐PLA composite. The mechanical tests indicated although the mechanical properties of sc‐PLA increased significantly by reinforcing with flax, the ALK‐flax/sc‐PLA composite showed little lower mechanical properties than UN‐flax/sc‐PLA composite. The alkali treatment of flax had no obvious influence on the Vicat softening temperature (VST) of flax/sc‐PLA composites, a higher heat resistance with VST at ～155°C could be obtained for flax/sc‐PLA composite. POLYM. ENG. SCI., 55:2553–2558, 2015. © 2015 Society of Plastics Engineers     

Effect of short polyethylene terephthalate fibers on properties of ethylene-propylene diene rubber composites

The alteration in some properties of electron beam (EB) cured ethylene-propylene diene rubber (EPDM) reinforced by polyethylene terephthalate (PET) fiber was investigated in this study. Bonding system Resorcinol/Hexamethylenetetramine/Silica (RHS) was used to enhance the fiber/EPDM adhesion and to maintain optimum composite strength properties. Mechanical properties of composites namely; tensile strength, hardness and modulus at 100 % elongation have been enhanced by adding PET fibers and increasing irradiation dose. Moreover, the effect of fiber loading and irradiation dose on the soluble fraction behavior of the composite in benzene was also investigated. The soluble fraction of the composites decreased with increasing the fiber loading and irradiation dose. The extent of fiber alignment and strength of fiber-rubber interface adhesion were analyzed from the anisotropic swelling measurements. In addition, thermal stability of the composites was increased. Besides, the mechanical properties like tensile strength and stiffness were improved by thermal ageing. Scanning electron microscopy (SEM) for the fractured surfaces and Wide- angle X- ray diffraction (WAXD) of the investigated samples confirmed that the adhesion occurred between fibers and EPDM.     

Study on the mechanical and thermal properties of poly(lactic acid)/office waste paper fiber composites

Environment friendly composites with favorable mechanical properties and low water absorption performance were successfully produced from poly(lactic acid) (PLA), office waste paper fiber (OWF), and coupling agents. The perfect sample was easily manufactured by melting–blending and injection molding. The PLA/OWF composites were comparable with other PLA/plant fiber composites, and the results indicated that the PLA/OWF composites show better performance than PLA/wheat straw fiber composites and PLA/bamboo fiber composites. On this basis, influence of modification of OWF on the properties of composites was investigated. The infrared results show that the OWF modification by different coupling agents was successful, and the scanning electron microscopy indicates that prepared composites exhibit good interfacial compatibility due to preferable binding force between fiber and matrix. With addition of 2 wt% γ-(2,3-propylene oxides)propyl trimethylsilane, the composite exhibits high tensile strength of 58.96 MPa, reflecting increase of 14% than the pure PLA. According to the crystallization and melting performance table, OWF can act as nucleating agent to promote the crystallization properties on composites, while the coupling agents have little effect on thermal stability. This article confirmed that the OWF has appropriate properties and is suitable for preparing composite materials and this work provides a novel idea for the utilization of office waste paper.     

Valorization of bio-calcium carbonate based Chamelea gallina shell waste fillers in shape memory polymer composites

In recent years, the focus has been on the use of calcium carbonate-based seashell wastes in the production of new thermoplastic and thermoset polymer materials, paving the way for their use as biofillers in polymeric composites. In this study, it is aimed to obtain a new polymeric composite material by doping Chamelea gallina shells, on polylactic acid (PLA)/polyethylene glycol (PEG) blend. Structural characterization of the obtained PLA/PEG blend/C. gallina composite films was performed with attenuated total reflection infrared spectroscopy (ATR-IR). When the thermal properties of composite materials were examined by thermogravimetric analysis (TGA), it was determined that the thermal stability of polymeric composites increased with the addition of C. gallina. SEM images showed that the polymer blend films, which appeared to have a porous structure, filled the pores with increasing C. gallina ratio. It was observed that the biodegradability of PLA/PEG blend composite films decreased with increasing C. gallina shells addition. However, C. gallina had a positive effect on the swelling and water absorption capacities of polymeric composites. The increase in tensile strength and elongation at break values of PLA/PEG blend/C. gallina composite films with increasing C. gallina means that the mechanical properties of the polymer are improved.     

Mechanical and thermal properties of bamboo fiber reinforced polypropylene/polylactic acid composites for 3D printing

In this article, a kind of degradable composite was prepared from bamboo fiber (BF), poly lactic acid (PLA), and polypropylene (PP). The mechanical and thermal properties were characterized by the universal testing machine, thermogravimetric analysis, differential scanning calorimetry. In order to improve the compability between BF and polymer matrix several modification on the surface of BF were explored and compared. Moreover, a compatibilizer (maleated PP) was applied to further increase compatibility between the fiber and matrix. It is found that the thermal stability of BF/PP/PLA composites decreased with the increase of maleated polypropylene (MAPP) content. When 5% MAPP was used the tensile strength, flexural strength, and impact strength of composites reached 33.73, 47.18 MPa, and 3.15 KJ/m², with an increase by 13, 11.7, and 23.5%, respectively, compared with the composites without MAPP. The improvement of mechanical properties is attributed to the fact that irregular grooves and cracks induced by the modification of BF facilitate the infiltration of polymer into fiber due to the strong capillary effect. Furthermore, BF/PP/PLA composites are potential to be used in 3D printing. POLYM. ENG. SCI., 59:E247–E260, 2019. © 2018 Society of Plastics Engineers     

Synthesis of poly(butylene succinate)/glass fiber composite by irradiation and its biodegradability

A composite was synthesized by irradiation of poly(butylene succinate) (PBS) and glass fiber (GF) in the presence of a polyfunctional monomer, trimethallyl isocyanurate (TMAIC), which accelerates gel formation of the matrix (PBS) in the composite. The highest gel fraction was achieved at 1% concentration of TMAIC at the dose level of 200 kGy compared to other concentrations. Mechanical properties of the composites were highly dependent on the gel fraction of the polymer and volume fraction of glass fiber reinforcement in the composite. Optimal conditions to synthesize a PBS/GF composite reaching maximum value of bending strength were 1% TMAIC, 67% fiber volume fraction, and irradiation dose of 200 kGy. These synthesized PBS/GF composites can be degraded by enzymes produced from the microorganism population in soil. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2122–2127, 2004     

MCC对PLA/PPC复合材料力学性能与热稳定性的影响

以微晶纤维素(MCC)作为改性剂,马来酸酐接枝聚乳酸(PLA g MAH)为界面相容剂,聚乳酸(PLA)、聚碳酸亚丙酯(PPC)为基体,通过熔融共混法制得PLA/PPC/MCC三元复合材料。采用控温拉伸、动态热分析、扫描电子显微镜以及热失重分析等方法研究了MCC对PLA/PPC的力学性能和热稳定性。结果表明,PLA/PPC/MCC三元复合材料的拉伸强度提高了12.7 %,玻璃化转变温度（Tg）提高了9.8 ℃;PLA g MAH的加入可以改善PLA/PPC/MCC三元复合材料的界面性质,从而提高力学性能和热稳定性;当PLA g MAH的添加量为5 %（质量分数,下同）时,三元复合材料在常温下的拉伸强度、弯曲强度和冲击强度分别提高了53.7 %、43.1 %和18.5 %;在60 ℃下三元复合材料的断裂强度提高了80 %;热降解温度以及最大失重温度与PLA/PPC相比分别提高了25.31 ℃和61.83 ℃。     

Tensile properties of plant fibre‐polymer composites in fire

The structural performance of polymer composites reinforced with plant fibres when exposed to fire was experimentally evaluated and compared against an E‐glass fibre laminate. Fire testing under combined one‐sided radiant heating and static tensile loading revealed that flax, jute, or hemp fibre composites experience more rapid thermal softening and fail within much shorter times than the fibreglass laminate, which is indicative of vastly inferior structural performance in fire. The plant fibre composites soften and fail before the onset of thermal decomposition of the plant fibres and polymer matrix, whereas the E‐glass fibres provide the composite with superior tensile properties to higher temperatures and higher applied tensile stresses. The tensile performance of the three types of plant fibre composites in fire was not identical. When exposed to the same radiant heat flux, the flax fibre composite could withstand higher tensile stresses for longer times than the hemp and jute laminates, which showed similar performance.     

PLA/MCC复合材料的制备及其性能

以水稻秸秆经碱解、酸解得到的微晶纤维素(MCC)作为聚乳酸(PLA)的改性材料,通过溶液共混、流延成膜制备了PLA/MCC复合膜,采用傅里叶变换红外光谱仪、差示扫描量热仪、扫描电子显微镜等对其性能进行了表征。结果表明:水稻秸秆中木质素、半纤维素等杂质大部分被有效除去,当NaOH质量分数为5%时,去除率最大,MCC成功制备;当MCC质量分数为8.3%时,可以最大程度改善PLA/MCC复合膜的拉伸性能,MCC与PLA结合最好,而MCC的加入会使复合膜的热稳定性有所降低。     

Biodegradable poly(lactic acid)/poly(butylene succinate)/wood flour composites: Physical and morphological properties

This work sought to improve the toughness and thermal stability of poly(lactic acid) (PLA) by incorporating poly(butylene succinate) (PBS) and wood flour (WF). The PLA/PBS blends showed a PBS‐dose‐dependent increase in the impact strength, elongation at break, degree of crystallinity, and thermal stability compared to the PLA, but the tensile strength, Young's modulus, and flexural strength were all decreased with increasing PBS content. Based on the optimum impact strength and elongation at break, the 70/30 (w/w) PLA/PBS blend was selected for preparing composites with five loadings of WF (5–30 phr). The impact strength, tensile strength, flexural strength, and thermal stability of the PLA/PBS/WF composites decreased with increasing WF content, and the degree of crystallinity was slightly increased compared to the 70/30 (w/w) PLA/PBS blend. Based on differential scanning calorimetry, the inclusion of PBS and WF into PLA did not significantly change the glass transition and melting temperatures of PLA in the PLA/PBS blends and PLA/PBS/WF composites. From the observed cold crystallization temperature of PLA in the samples, it was evident that the degree of crystallinity of PLA in all the blends and composites was higher than that of PLA. The PLA/PBS blend and PLA/PBS/WF composite degraded faster than PLA during three months in natural soil, which was due to the fast degradation rate of PBS. POLYM. COMPOS., 38:2841–2851, 2017. © 2016 Society of Plastics Engineers     

Properties of kenaf fiber/polylactic acid biocomposites plasticized with polyethylene glycol

Biocomposites of kenaf fiber (KF) and polylactic acid (PLA) were prepared by an internal mixer and compression molding. PLA was plasticized with polyethylene glycol (PEG) (10 wt%) and evaluated as the polymer matrix (p‐PLA). Fiber loadings were varied between 0 and 40 wt%. The tensile, dynamic mechanical, and morphological properties and water absorption behavior of these composites were studied. Reinforcing effect of KF was observed when fiber loading exceeded 10 wt% despite of the inferior fiber‐matrix adhesion observed via scanning electron microscopy (SEM). Un‐plasticized PLA/KF composite exhibited higher tensile properties than its plasticized counterpart. Fiber breakage and heavily coated short pulled‐out of fibers were observed from the SEM micrographs of the composite. The presence of PEG might have disturbed the fiber‐matrix interaction between KF and PLA in the plasticized composites. Addition of PEG slightly improved the un‐notched impact strength of the composites. Dynamic mechanical analysis showed that the storage and loss moduli of p‐PLA/KF composites increased with the increase in fiber loading due to increasing restrictions to mobility of the polymer molecules. The tan delta of the composites in contrast showed an opposite trend. p‐PLA and p‐PLA/KF composites exhibited non‐Fickian behavior of water absorption. SEM examination revealed microcracks on p‐PLA and p‐PLA/KF surfaces. POLYM. COMPOS., 31:1213–1222, 2010. © 2009 Society of Plastics Engineers     

Mechanical and thermal characterization of compression moulded polylactic acid natural fiber composites reinforced with hemp and lyocell fibers

This research evaluates the effects of PLA/PP blend ratio and Lyocell/hemp mixture ratio on the morphology, water absorption, mechanical and thermal properties of PLA‐based composites. The composites were fabricated with 30 mass % hemp using compression moulding. As a reference composites made from PP were also studied. Combining of hemp and Lyocell in PLA composite leads to the reduction of moisture absorption and can improve the impact, tensile, flexural properties when compared with PLA/hemp. Composite based on the PLA/PP blend‐matrix could not improve the tensile and flexural properties compared with PLA/hemp, however; the lighter composite with better impact properties was obtained. The crystallization temperature of the PLA‐PP/hemp increased compared with pure PLA. This result was also confirmed by the SEM micrographs. The moisture absorption of PLA‐PP/hemp was higher than PLA/hemp. Based on theoretical analysis of DMTA data, there was favorable adhesion in all composites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40534.     

Preparation of acylated microcrystalline cellulose using olive oil and its reinforcing effect on poly(lactic acid) films for packaging application

A novel poly(lactic acid) (PLA) based composite, reinforced by microcrystalline cellulose (MCC) was prepared. MCC was modified by esterification reaction using olive oil for improving the compatibility with PLA matrix. The acylated microcrystalline cellulose (AMCC) exhibited reduced polarity in comparison to unmodified MCC. AMCC/ PLA composite films were prepared using solvent casting technique. The effects of the MCC surface modification on morphological, mechanical, physical, thermal, biodegradability and barrier properties of the PLA based MCC composites were studied. FTIR analysis confirmed acylation reaction of MCC. Scanning electron microscopy analysis exhibited a uniform distribution of AMCC in PLA matrix. Barrier properties of AMCC based composites were improved as compared to MCC based composites. The tensile strength and tensile modulus of composite films (at 2 wt.% AMCC) were improved about 13% and 35% as much as those of the pure PLA films, respectively. These biodegradable composite films can be a sustainable utilization of olive oil and microcrystalline cellulose in the food packaging application.     

辐照交联中密度聚乙烯中空纤维管的结构与性能

研究了加工条件对辐照交联中密度聚乙烯中空纤维管凝聚态结构和力学性能的影响,特别是辐照剂量与中空纤维管抗拉性能和耐扩张性能的关系,并研究了中空纤维管的交联度、结构、晶形和热性能。结果表明:辐照交联聚乙烯中空纤维管的结构和性能可以通过辐照工艺来调控,辐照剂量升高,中空纤维管的凝胶含量提高,抗拉强度增加。     

Preparation and properties of successive alkali treated completely biodegradable short jute fiber reinforced PLA composites

The natural fiber reinforced biodegradable polymer composites were prepared with short jute fiber as reinforcement in PLA (Poly lactic acid) matrix. The short jute fiber is successively treated with NaOH at various concentrations (5%, 10%, and 15%) and H₂O₂. The composites were prepared with untreated and treated short jute fibers at different weight proportions (up to 25%) in PLA and investigated for mechanical properties. The results showed that the composite with successive alkali treated jute fiber at 10% NaOH and H₂O₂ with 20% fiber loading has shown 18% higher flexural strength than neat PLA and untreated jute/PLA composite. The flexural modulus of the composite at 25% fiber loading was 125% and 110% higher than that of composites with untreated fibers and neat PLA, respectively. The impact strength of composite with untreated fibers at higher fiber weight fraction was 23% high as compared to neat PLA and 26% high compared to composite with treated fibers. The water absorption was more for untreated jute/PLA composite at 25% fiber loading than all other composites. The composite with untreated fibers has high thermal degradation compared with treated fibers but lower than that of pure PLA matrix. The enzymatic environment has increased the rate of degradation of composites as compared to soil burial. Surface morphology of biodegraded surfaces of the composites were studied using SEM method. POLYM. COMPOS., 37:2160–2170, 2016. © 2015 Society of Plastics Engineers     

微晶纤维素/聚乳酸复合材料的性能研究

以微晶纤维素为填充剂,聚乳酸为基体,采用熔融共混法制备PLA/MCC生物降解复合材料。考察了聚甲基丙烯酸甲酯(PMMA)表面处理的微晶纤维素对复合材料性能的影响。结果表明,PMMA包覆MCC增加了弯曲强度。表面改性处理提高了MCC的热稳定性,使其加工温度提高了。     

Physical properties of electron beam irradiated poly(vinyl butyral) composites with carbamate,imidazole, and tetrazolium dye

Films of poly(vinyl butyral) composites with triphenyl tetrazolium chloride dye (TTC) and the antioxidant nickel dibutyl dithiocarbamate (NBC) or 2‐mercaptobenzimidazole (MBI) were prepared by the solution casting method using butyl alcohol as a solvent. The effect of various doses of electron beam irradiation (50–200 kGy) on color response, thermal, and mechanical properties were investigated. The color measurements showed that the films of the different composites possessed a high sensitivity to electron beam irradiation, in which the nearly colorless films were changed to deep red color, which can be easily detected by visual observations. In addition, the change in color depends on irradiation dose and the contents of the TTC dye. Moreover, the presence of the antioxidants NBC or MBI has no effect on the development of color. However, PVB/TTC and PVB/TTC/MBI composites showed high regular change in color as a function of irradiation dose. The thermogravimetric analysis used to study the thermal stability indicated that PVB/TTC composites either before or after electron beam irradiation are thermally more stable than neat PVB polymer. The presence of the antioxidants NBC or MBI offered protection to PVB/TTC composites against decomposition or oxidative degradation resulted from irradiation. Blending unirradiated PVB with TTC dye, mixture of TTC and NBC, and mixture of TTC and MBI reduced the tensile strength by 4, 20, and 17% upon blending, respectively. However, the reduction in tensile strength of the entire composite films (～7% based on the initial value) upon exposure to a dose of 50 kGy is acceptable for practical applications. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4358–4365, 2006