Simple and Low-Cost Vanadyl Oxalate as Hole Transporting Layer Enables Efficient Organic Solar Cells

Organic solar cells (OSCs) with the conventional configuration usually use polyethylenedioxythiophene:polystyrene sulfonate (PEDOT:PSS) as the hole-transporting layer (HTL); however, its acidity tends to affect the performance and long-term stability of the devices. Therefore, replacing PEDOT:PSS with other more stable HTLs is essential for realizing the practical applications of OSCs. To achieve this goal, a simple and low-cost vanadyl oxalate (VOC₂O₄) is identified as a HTL to facilitate high power conversion efficiencies (PCEs), good stability, and high thickness tolerance to be achieved in OSCs. The VOC₂O₄ thin film can be easily prepared by spin-coating from its aqueous solution onto ITO/glass substrate and thermally annealed at 100 °C to exhibit high transmittance, conductivity, and work function. It can be applied as a robust HTL with wide processing conditions, especially after being heated at 200 °C and treated with UV-ozone (UVO) to afford a very high PCE of 18.94% in OSCs. This value is among the highest PCEs obtained for binary OSCs. In addition, the derived OSCs exhibit high thickness tolerance and better stability than those based on PEDOT:PSS as HTL. These results reveal that VOC₂O₄ is an excellent HTL for OSCs, having great potential for large-area device applications.     

High efficiency arrays of polymer solar cells fabricated by spray‐coating in air

We present bulk heterojunction organic solar cells fabricated by spray‐casting both the PEDOT:PSS hole‐transport layer (HTL) and active PBDTTT‐EFT:PC₇₁BM layers in air. Devices were fabricated in a (6 × 6) array across a large‐area substrate (25 cm²) with each pixel having an active area of 6.45 mm². We show that the film uniformity and operational homogeneity of the devices are excellent. The champion device with spray cast active layer on spin cast PEDOT:PSS had an power conversion efficiency (PCE) of 8.75%, and the best device with spray cast active layer and PEDOT:PSS had a PCE of 8.06%. The impacts of air and light exposure of the active layer on device performance are investigated and found to be detrimental. Copyright © 2015 John Wiley & Sons, Ltd.     

Layer by layer characterisation of the degradation process in PCDTBT:PC71BM based normal architecture polymer solar cells

This work demonstrates the stability and degradation of OSCs based on poly[N-9′-heptadecanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′ benzothiadiazole)] (PCDTBT): (6,6)-Phenyl C₇₁ butyric acid methyl ester (PC₇₁BM) photoactive blend layers as a function of ageing time in air. Analysis of the stability and degradation process for the OSCs was conducted under ambient air by using current-voltage (I-V) measurements and x-ray photoelectron spectroscopy (XPS). The interface between photoactive layer and HTL (PEDOT:PSS) was also investigated. Device stability was investigated by calculating decay in power conversion efficiency (PCE) as a function of ageing time in the air. The PCE of devices decrease from 5.17 to 3.61% in one week of fabrication, which is attributed to indium and oxygen migration into the PEDOT:PSS and PCDTBT:PC₇₁BM layer. Further, after aging for 1000 h, XPS spectra confirm the significant diffusion of oxygen into the HTL and photoactive layer which increased from 3.0 and 23.3% to 20.4 and 35.7% in photoactive layer and HTL, respectively. Similarly, the indium content reached to 17.9% on PEDOT:PSS surface and 0.4% on PCDTBT:PC₇₁BM surface in 1000 h. Core-level spectra of active layer indicate the oxidation of carbon atoms in the fullerene cage, oxidation of nitrogen present in the polymer matrix and formation of In₂O₃ due to indium diffusion. We also observed a steady fall in the optical absorption of the active layer during ageing in ambient air and it reduced to 76.5% of initial value in 1000 h. On the basis of these experimental results, we discussed key parameters that account for the degradation process and stability of OSCs in order to improve the device performance.     

PEDOT:PSS‐Assisted Exfoliation and Functionalization of 2D Nanosheets for High‐Performance Organic Solar Cells

Here, a facial and scalable method for efficient exfoliation of bulk transition metal dichalcogenides (TMD) and graphite in aqueous solution with poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) to prepare single‐ and few‐layer nanosheets is demonstrated. Importantly, these TMD nanosheets retain the single crystalline characteristic, which is essential for application in organic solar cells (OSCs). The hybrid PEDOT:PSS/WS₂ ink prepared by a simple centrifugation is directly integrated as a hole extraction layer for high‐performance OSCs. Compared with PEDOT:PSS, the PEDOT:PSS/WS₂‐based devices provide a remarkable power conversion efficiency due to the “island” morphology and benzoid–quinoid transition. This study not only demonstrates a novel method for preparing single‐ and few‐layer TMD and graphene nanosheets but also paves a way for their applications without further complicated processing.     

MoO3/Au/MoO3–PEDOT:PSS multilayer electrodes for ITO-free organic solar cells

The effect of the MoO₃–PEDOT:PSS composite layer in the MoO₃/Au/MoO₃–PEDOT:PSS multilayer electrode on the power conversion efficiency of ITO-free organic solar cells (OSCs) was evaluated. The MoO₃ (30 nm)/Au(12 nm)/MoO₃–PEDOT:PSS (30 nm)/PEDOT:PSS structure showed ~7% more optical transmittance than the MoO₃ (30 nm)/Au (12 nm)/MoO₃(30 nm)/PEDOT:PSS structure at 550 nm wavelength. The OSCs using MoO₃/Au/MoO₃–PEDOT:PSS multilayer electrodes as anodes showed a considerable improvement in power conversion efficiency (PCE), from 1.84% to 2.81%, comparable to ITO based OSCs with PCE of 2.89%. This improvement is attributed to the suppression of MoO₃ dissolution by the acidic hole transport layer (HTL) PEDOT:PSS on the MoO₃/Au/MoO₃–PEDOT:PSS multilayer electrode, resulting in high J_sc, V_oc and FF of the OSCs. This composite based multilayer electrode was shown to be a promising replacement in ITO-free flexible optoelectronic devices.     

An ammonia modified PEDOT: PSS for interfacial engineering in inverted planar perovskite solar cells

Poly(3,4-ethylenedioxythiophene)-poly(styrene sulfonate) (PEDOT:PSS) is one of the most widely used hole transport layers (HTL) in inverted perovskite solar cells (PSCs) due to its simple solution-processed ability, high transparency, and conductivity. However, PEDOT:PSS-based devices suffer a lower open-circuit voltage (V_oc) than devices with the conventional structure. To address this issue, we fabricated ammonia-modified PEDOT:PSS films by simply doping PEDOT:PSS solution with different ratio of ammonia. The acidity of PEDOT:PSS can be neutralized by the doped ammonia, which inhibits the ion-exchange reaction between PSS-H and CH₃NH₃I, thus retarding the reduction of the work function for PEDOT:PSS to some extent. As a result, a superior power conversion efficiency (PCE) of 15.5% was obtained for the device based on the ammonia-doped PEDOT:PSS HTL than that of the pristine PEDOT:PSS-based device. We ascribe the PCE enhancement to the increased V_oc and fill factor (FF), which is attributed not only to the better energy-level alignment between the ammonia-modified PEDOT:PSS film and perovskite layer but also to the increased grain size and crystallinity of perovskite film.     

Printable and Large‐Area Organic Solar Cells Enabled by a Ternary Pseudo‐Planar Heterojunction Strategy

Bulk heterojunction (BHJ) processing technology has had an irreplaceable role in the development of organic solar cells (OSCs) in the past decades due to the significant advantages in achieving high‐power conversion efficiency (PCE). However, the difficulty in exploring and regulating morphology makes it inadequate for upscaling large‐area OSCs. In this work, printable high‐performance ternary devices are fabricated by a pseudo‐planar heterojunction (PPHJ) strategy. The fullerene derivative indene‐C₆₀ bisadduct (ICBA) is incorporated into PM6/IT‐4F system to expand the vertical phase separation and facilitate an obvious PPHJ structure. After the addition of ICBA, the IT‐4F enriches on the surface of active layer, while PM6 is accumulated underneath. Furthermore, it increases the crystallinity of PM6, which facilitates exciton dissociation and charge transfer. Accordingly, 1.05 cm² devices are fabricated by blade‐coating with an enhanced PCE of 14.25% as compared to the BHJ devices (13.73%). The ternary PPHJ strategy provides an effective way to optimize the vertical phase separation of organic semiconductor during scalable printing methods.     

Efficient and Stable Perovskite Solar Cells via Dual Functionalization of Dopamine Semiquinone Radical with Improved Trap Passivation Capabilities

Highly efficient planar heterojunction perovskite solar cells (PVSCs) with dopamine (DA) semiquinone radical modified poly(3,4‐ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) (DA‐PEDOT:PSS) as a hole transporting layer (HTL) were fabricated. A combination of characterization techniques were employed to investigate the effects of DA doping on the electron donating capability of DA‐PEDOT:PSS, perovskite film quality and charge recombination kinetics in the solar cells. Our study shows that DA doping endows the DA‐PEDOT:PSS‐modified PVSCs with a higher radical content and greater perovskite to HTL charge extraction capability. In addition, the DA doping also improves work function of the HTL, increases perovskite film crystallinity, and the amino and hydroxyl groups in DA can interact with the undercoordinated Pb atoms on the perovskite crystal, reducing charge‐recombination rate and increasing charge‐extraction efficiency. Therefore, the DA‐PEDOT:PSS‐modified solar cells outperform those based on PEDOT:PSS, increasing open‐circuit voltage (V _oc) and power conversion efficiency (PCE) to 1.08 V and 18.5%, respectively. Even more importantly, the efficiency of the unencapsulated DA‐PEDOT:PSS‐based PVSCs are well retained with only 20% PCE loss after exposure to air for 250 hours. These in‐depth insights into structure and performance provide clear and novel guidelines for the design of effective HTLs to facilitate the practical application of inverted planar heterojunction PVSCs.     

Simultaneous enhancement of the efficiency and stability of organic solar cells using PEDOT:PSS grafted with a PEGME buffer layer

We report a simple processing method to simultaneously improve the efficiency and stability of organic solar cells (OSCs). Poly(4-styrene sulfonate)-doped poly(3,4-ethylenedioxy-thiophene (PEDOT:PSS), widely used as hole transport layer (HTL) in OSCs, tends to accelerate the degradation of devices because of its hygroscopic and acidic properties. In this regard, we have modified PEDOT:PSS to reduce its hygroscopic and acidic properties through a condensation reaction between PEDOT:PSS and poly(ethylene glycol) methyl ether (PEGME) in order to improve the efficiency and stability of OSCs. As a result, the power conversion efficiency (PCE) increased by 21%, from 2.57% up to 3.11%. A better energy level alignment by the reduced work function of the modified PEDOT:PSS with a highest occupied molecular orbital (HOMO) level of poly(3-hexylthiophene-2,5-diyl) (P3HT) is considered the origin of the improved the efficiency. The half-life of OSCs with PEDOT:PSS modified with PEGME buffer layer also increased up to 3.5 times compared to that of devices with pristine PEDOT:PSS buffer layer.     

A Self-Assembled Vertical-Gradient and Well-Dispersed MXene Structure for Flexible Large-Area Perovskite Modules

Advancing hole transport layers (HTL) to realize large-area, flexible, and high-performance perovskite solar cells (PSCs) is one of the most challenging issues for its commercialization. Here, a self-assembled gradient Ti₃C₂T_x MXene incorporated PEDOT:PSS HTL is demonstrated to achieve high-performance large-area PSCs by establishing half-caramelization-based glucose-induced MXene redistribution. Through this process, the Ti₃C₂T_x MXene nanosheets are spontaneously dispersed and redistributed at the top region of HTL to form the unique gradient distribution structure composed of MXene:Glucose:PEDOT:PSS (MG-PEDOT). These results show that the MG-PEDOT HTL not only offers favorable energy level alignment and efficient charge extraction, but also improves the film quality of perovskite layer featuring enlarged grain size, lower trap density, and longer carrier lifetime. Consequently, the power conversion efficiency (PCE) of the flexible device based on MG-PEDOT HTL is increased by 36% compared to that of pristine PEDOT:PSS HTL. Meanwhile, the flexible perovskite solar minimodule (15 cm² area) using MG-PEDOT HTL achieve a PCE of 17.06%. The encapsulated modules show remarkable long-term storage stability at 85 °C in ambient air (≈90% efficiency retention after 1200 h) and enhanced operational lifetime (≈90% efficiency retention after 200 h). This new approach shows a promising future of the self-assembled HTLs for developing optoelectronic devices.     

Use of the Phen‐NaDPO:Sn(SCN)2 Blend as Electron Transport Layer Results to Consistent Efficiency Improvements in Organic and Hybrid Perovskite Solar Cells

A simple approach that enables a consistent enhancement of the electron extracting properties of the widely used small‐molecule Phen‐NaDPO and its application in organic solar cells (OSCs) is reported. It is shown that addition of minute amounts of the inorganic molecule Sn(SCN)₂ into Phen‐NaDPO improves both the electron transport and its film‐forming properties. Use of Phen‐NaDPO:Sn(SCN)₂ blend as the electron transport layer (ETL) in binary PM6:IT‐4F OSCs leads to a remarkable increase in the cells' power conversion efficiency (PCE) from 12.6% (Phen‐NaDPO) to 13.5% (Phen‐NaDPO:Sn(SCN)₂). Combining the hybrid ETL with the best‐in‐class organic ternary PM6:Y6:PC₇₀BM systems results to a similarly remarkable PCE increase from 14.2% (Phen‐NaDPO) to 15.6% (Phen‐NaDPO:Sn(SCN)₂). The consistent PCE enhancement is attributed to reduced trap‐assisted carrier recombination at the bulk‐heterojunction/ETL interface due to the presence of new energy states formed upon chemical interaction of Phen‐NaDPO with Sn(SCN)₂. The versatility of this hybrid ETL is further demonstrated with its application in perovskite solar cells for which an increase in the PCE from 16.6% to 18.2% is also demonstrated.     

Mitigating Detrimental Effect of Self-Doping Near the Anode in Highly Efficient Organic Solar Cells

Poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) has been one of the most established hole transport layers (HTL) in organic solar cells (OSCs) for several decades. However, the presence of PSS⁻ ions is known to deteriorate device performance via a number of mechanisms including diffusion to the HTL-active layer interface and unwanted local chemical reactions. In this study, it is shown that PSS⁻ ions can also result in local p-doping in the high efficiency donor:non-fullerene acceptor blends – resulting in photocurrent loss. To address these issues, a facile and effective approach is reported to improve the OSC performance through a two-component hole transport layer (HTL) consisting of a self-assembled monolayer of 2PACz ([2-(9H-Carbazol-9-yl)ethyl]phosphonic acid) and PEDOT:PSS. The power conversion efficiency (PCE) of 17.1% using devices with PEDOT:PSS HTL improved to 17.7% when the PEDOT:PSS/2PACz two-component HTL is used. The improved performance is attributed to the overlaid 2PACz layer preventing the formation of an intermixed p-doped PSS⁻ ion rich region (≈5–10 nm) at the bulk heterojunction-HTL contact interface, resulting in decreased recombination losses and improved stability. Moreover, the 2PACz monolayer is also found to reduce electrical shunts that ultimately yield improved performance in large area devices with PCE enhanced from 12.3% to 13.3% in 1 cm² cells.     

Solution‐Processed Thermally Activated Delayed Fluorescent OLED with High EQE as 31% Using High Triplet Energy Crosslinkable Hole Transport Materials

Solution‐processed organic light‐emitting diodes (OLEDs) with thermally activated delayed fluorescent (TADF) material as emitter have attracted much attention because of their low cost and high performance. However, exciton quench at the interface between the hole injection layer, poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS), and emitting layer (EML) in devices can lead to low device performance. Here, a novel high triplet energy (2.89 eV) and crosslinkable hole‐transporting material grafted with oxetane groups, N,N‐bis(4‐(6‐((3‐ethyloxetan‐3‐yl)methoxy)hexyloxy)phenyl)‐3,5‐di(9H‐carbazol‐9‐yl)benzenamine (Oxe‐DCDPA)), as crosslinked hole transport layer (HTL) into the interface of PEDOT:PSS layer and EML is proposed for prevention of exciton quenching, and among the reported devices with single HTL in solution‐processed TADF‐OLED, the highest external quantum efficiency (EQE)/luminous efficiency (η_L) of 26.1%/94.8 cd A^?1 and 24.0%/74.0 cd A^?1 are achieved for green emission (DACT‐II as emitter) and bluish‐green emission (DMAC‐TRZ as emitter), respectively. Further improvement, using double HTLs, composed of N,N′‐bis(4‐(6‐((3‐ethyloxetan‐3‐yl)methoxy))‐hexylphenyl)‐N,N′‐diphenyl‐4,4′‐diamine with high hole mobility and Oxe‐DCDPA with high triplet energy, leads to the highest EQE/η_L of 30.8%/111.9 cd A^?1 and 27.2%/83.8 cd A^?1 for green emission and bluish‐green emission, respectively. These two devices show the high maximum brightness of 81 100 and 70 000 cd m^?2, respectively.     

Design of Multilayered Nanostructures and Donor–Acceptor Interfaces in Solution‐Processed Thin‐Film Organic Solar Cells

Multilayered polymer thin‐film solar cells have been fabricated by wet processes such as spin‐coating and layer‐by‐layer deposition. Hole‐ and electron‐transporting layers were prepared by spin‐coating with poly(3,4‐ethylenedioxythiophene) oxidized with poly(4‐styrenesulfonate) (PEDOT:PSS) and fullerene (C₆₀), respectively. The light‐harvesting layer of poly‐(p‐phenylenevinylene) (PPV) was fabricated by layer‐by‐layer deposition of the PPV precursor cation and poly(sodium 4‐styrenesulfonate) (PSS). The layer‐by‐layer technique enables us to control the layer thickness with nanometer precision and select the interfacial material at the donor–acceptor heterojunction. Optimizing the layered nanostructures, we obtained the best‐performance device with a triple‐layered structure of PEDOT:PSS|PPV|C₆₀, where the thickness of the PPV layer was 11 nm, comparable to the diffusion length of the PPV singlet exciton. The external quantum efficiency spectrum was maximum (ca. 20%) around the absorption peak of PPV and the internal quantum efficiency was estimated to be as high as ca. 50% from a saturated photocurrent at a reverse bias of ?3 V. The power conversion efficiency of the triple‐layer solar cell was 0.26% under AM1.5G simulated solar illumination with 100 mW cm^?2 in air.     

Moderately reduced graphene oxide/PEDOT:PSS as hole transport layer to fabricate efficient perovskite hybrid solar cells

Graphene oxide (GO) with single layer was moderately reduced at 200 °C for 4 h under N₂. Then the moderately reduced graphene oxide (rGO) water solution was employed as an additive to tune the properties of conventional poly(ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) solution. It's found that the incorporation of rGO into PEDOT:PSS nearly did not change its transparency, hydrophilic property, or the surface roughness. So, the rGO/PEDOT:PSS composite was used as a hole transport layer (HTL) to fabricate perovskite solar cells (PSCs). As a result, PSCs with rGO/PEDOT:PSS as HTL exhibit improved power conversion efficiency than that of PSCs with PEDOT:PSS as HTL. Our findings show that moderately reduced rGO/PEDOT:PSS could be an efficient HTL to improve power conversion efficiency of PSCs.     

Conjugated Small Molecule for Efficient Hole Transport in High‐Performance p‐i‐n Type Perovskite Solar Cells

The π‐conjugated organic small molecule 4,4′‐cyclohexylidenebis[N,N‐bis(4‐methylphenyl) benzenamine] (TAPC) has been explored as an efficient hole transport material to replace poly(3,4‐ethylenedio‐xythiophene):poly(styrenesulfonate) (PEDOT:PSS) in the preparation of p‐i‐n type CH₃NH₃PbI₃ perovskite solar cells. Smooth, uniform, and hydrophobic TAPC hole transport layers can be facilely deposited through solution casting without the need for any dopants. The power conversion efficiency of perovskite solar cells shows very weak TAPC layer thickness dependence across the range from 5 to 90 nm. Thermal annealing enables improved hole conductivity and efficient charge transport through an increase in TAPC crystallinity. The perovskite photoactive layer cast onto thermally annealed TAPC displays large grains and low residual PbI₂, leading to a high charge recombination resistance. After optimization, a stabilized power conversion efficiency of 18.80% is achieved with marginal hysteresis, much higher than the value of 12.90% achieved using PEDOT:PSS. The TAPC‐based devices also demonstrate superior stability compared with the PEDOT:PSS‐based devices when stored in ambient circumstances, with a relatively high humidity ranging from 50 to 85%.     

Tuning Hole Transport Layer Using Urea for High‐Performance Perovskite Solar Cells

Interface engineering is critical to the development of highly efficient perovskite solar cells. Here, urea treatment of hole transport layer (e.g., poly(3,4‐ethylene dioxythiophene):polystyrene sulfonate (PEDOT:PSS)) is reported to effectively tune its morphology, conductivity, and work function for improving the efficiency and stability of inverted MAPbI₃ perovskite solar cells (PSCs). This treatment has significantly increased MAPbI₃ photovoltaic performance to 18.8% for the urea treated PEDOT:PSS PSCs from 14.4% for pristine PEDOT:PSS devices. The use of urea controls phase separation between PEDOT and PSS segments, leading to the formation of a unique fiber‐shaped PEDOT:PSS film morphology with well‐organized charge transport pathways for improved conductivity from 0.2 S cm^?1 for pristine PEDOT:PSS to 12.75 S cm^?1 for 5 wt% urea treated PEDOT:PSS. The urea‐treatment also addresses a general challenge associated with the acidic nature of PEDOT:PSS, leading to a much improved ambient stability of PSCs. In addition, the device hysteresis is significantly minimized by optimizing the urea content in the treatment.     

Solution‐Processed Nickel Oxide Hole Transport Layers in High Efficiency Polymer Photovoltaic Cells

The detailed characterization of solution‐derived nickel (II) oxide (NiO) hole‐transporting layer (HTL) films and their application in high efficiency organic photovoltaic (OPV) cells is reported. The NiO precursor solution is examined in situ to determine the chemical species present. Coordination complexes of monoethanolamine (MEA) with Ni in ethanol thermally decompose to form non‐stoichiometric NiO. Specifically, the [Ni(MEA)₂(OAc)]⁺ ion is found to be the most prevalent species in the precursor solution. The defect‐induced Ni³⁺ ion, which is present in non‐stoichiometric NiO and signifies the p‐type conduction of NiO, as well as the dipolar nickel oxyhydroxide (NiOOH) species are confirmed using X‐ray photoelectron spectroscopy. Bulk heterojunction (BHJ) solar cells with a polymer/fullerene photoactive layer blend composed of poly‐dithienogermole‐thienopyrrolodione (pDTG‐TPD) and [6,6]‐phenyl‐C71‐butyric acid methyl ester (PC₇₁BM) are fabricated using these solution‐processed NiO films. The resulting devices show an average power conversion efficiency (PCE) of 7.8%, which is a 15% improvement over devices utilizing a poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) HTL. The enhancement is due to the optical resonance in the solar cell and the hydrophobicity of NiO, which promotes a more homogeneous donor/acceptor morphology in the active layer at the NiO/BHJ interface. Finally, devices incorporating NiO as a HTL are more stable in air than devices using PEDOT:PSS.     

Efficient Polymer Solar Cells Based on Poly(3‐hexylthiophene):Indene‐C70 Bisadduct with a MoO3 Buffer Layer

Polymer solar cells (PSCs) with poly(3‐hexylthiophene) (P3HT) as a donor, an indene‐C₇₀ bisadduct (IC₇₀BA) as an acceptor, a layer of indium tin oxide modified by MoO₃ as a positive electrode, and Ca/Al as a negative electrode are presented. The photovoltaic performance of the PSCs was optimized by controlling spin‐coating time (solvent annealing time) and thermal annealing, and the effect of the spin‐coating times on absorption spectra, X‐ray diffraction patterns, and transmission electron microscopy images of P3HT/IC₇₀BA blend films were systematically investigated. Optimized PSCs were obtained from P3HT/IC₇₀BA (1:1, w/w), which exhibited a high power conversion efficiency of 6.68%. The excellent performance of the PSCs is attributed to the higher crystallinity of P3HT and better a donor–acceptor interpenetrating network of the active layer prepared under the optimized conditions. In addition, PSCs with a poly(3,4‐ethylenedioxy‐thiophene):poly(styrenesulfonate) (PEDOT:PSS) buffer layer under the same optimized conditions showed a PCE of 6.20%. The results indicate that the MoO₃ buffer layer in the PSCs based on P3HT/IC₇₀BA is superior to that of the PEDOT:PSS buffer layer, not only showing a higher device stability but also resulting in a better photovoltaic performance of the PSCs.     

Versatile Self-Assembled Hole Transport Monolayer Enables Facile Processing Organic Solar Cells over 18% Efficiency with Good Generality

Simplifying solution-processing of bulk-heterojunction (BHJ) organic solar cells (OSCs) via efficient interfacial layers with good generality is in great demand for pushing their large-scale applications. In this study, such a novel and cost-effective self-assembled monolayer (SAM) is reported herein as efficient hole transport layer (HTL) for high efficiency OSCs. The SAM-structured 4-(5,9-dibromo-7H-dibenzo[c,g]carbazol-7-yl)butyl)phosphonic acid (DCB-BPA) enables not only enhanced photon harvesting in the active layer but also minimized nonradiative recombination losses to improve interface charge extraction/transport. As a consequence, high short-circuit current (≈28.07 mA cm⁻²) is achieved for PM6:BTP-eC9 based OSCs to deliver a champion power conversion efficiency of 18.16%, among the highest values for OSCs using small organic HTLs to date. Importantly, good generality of this SAMs is demonstrated for representative high-efficiency BHJ OSCs systems like PM6:Y6 and PM6:PC₆₁BM, outperforming conventional poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate)-based counterparts. Excitingly, the SAM is applicable for large-area HTL processing via immersion method, affording 16.59% efficiency for PM6:BTP-BO-4Cl based OSCs. This study highlights the great potential of engineered SAMs for facile large-scale fabrication of high performance OSCs.