Preparation,characterization, engine combustion and emission characteristics of rapeseed oil based hybrid fuels

In this study, hybrid fuels consisting of rapeseed oil/diesel blend, 1% aqueous ethanol and a surfactant (oleic acid/1-butanol mixture) were prepared and tested as a fuel in a direct injection (DI) diesel engine. The main fuel properties such as the density, viscosity and lower heating value (LHV) of these fuels were measured, and the engine performance, combustion and exhaust emissions were investigated and compared with that of diesel fuel. The experimental results showed that the viscosity and density of the hybrid fuels were decreased and close to that of diesel fuel with the increase of ethanol volume fraction up to 30%. The start of combustion was later than that of diesel fuel and the peak cylinder pressure, peak pressure rise rate and peak heat release rate were higher than those of diesel fuel. The brake specific fuel consumption (BSFC) of hybrid fuels was increased with the volume fraction of ethanol and higher than that of diesel. The brake specific energy consumption (BSEC) was almost identical for all test fuels. The smoke emissions were lower than those for diesel fuel at high engine loads, the NO_x emissions were almost similar to those of diesel fuel, but CO and HC emissions were higher, especially at low engine loads.     

Performance and emissions characteristics of Jatropha oil (preheated and blends) in a direct injection compression ignition engine

The scarce and rapidly depleting conventional petroleum resources have promoted research for alternative fuels for internal combustion engines. Among various possible options, fuels derived from triglycerides (vegetable oils/animal fats) present promising “greener” substitutes for fossil fuels. Vegetable oils, due to their agricultural origin, are able to reduce net CO₂ emissions to the atmosphere along with import substitution of petroleum products. However, several operational and durability problems of using straight vegetable oils in diesel engines reported in the literature, which are because of their higher viscosity and low volatility compared to mineral diesel fuel.In the present research, experiments were designed to study the effect of reducing Jatropha oil’s viscosity by increasing the fuel temperature (using waste heat of the exhaust gases) and thereby eliminating its effect on combustion and emission characteristics of the engine. Experiments were also conducted using various blends of Jatropha oil with mineral diesel to study the effect of reduced blend viscosity on emissions and performance of diesel engine. A single cylinder, four stroke, constant speed, water cooled, direct injection diesel engine typically used in agricultural sector was used for the experiments. The acquired data were analyzed for various parameters such as thermal efficiency, brake specific fuel consumption (BSFC), smoke opacity, CO₂, CO and HC emissions. While operating the engine on Jatropha oil (preheated and blends), performance and emission parameters were found to be very close to mineral diesel for lower blend concentrations. However, for higher blend concentrations, performance and emissions were observed to be marginally inferior.     

Performance,emission and combustion characteristics of a variable compression ratio engine using methyl esters of waste cooking oil and diesel blends

The performance, emission and combustion characteristics of a single cylinder four stroke variable compression ratio multi fuel engine when fueled with waste cooking oil methyl ester and its 20%, 40%, 60% and 80% blends with diesel (on a volume basis) are investigated and compared with standard diesel. The suitability of waste cooking oil methyl ester as a biofuel has been established in this study. Bio diesel produced from waste sun flower oil by transesterification process has been used in this study. Experiment has been conducted at a fixed engine speed of 1500 rpm, 50% load and at compression ratios of 18:1, 19:1, 20:1, 21:1 and 22:1. The impact of compression ratio on fuel consumption, combustion pressures and exhaust gas emissions has been investigated and presented. Optimum compression ratio which gives best performance has been identified. The results indicate longer ignition delay, maximum rate of pressure rise, lower heat release rate and higher mass fraction burnt at higher compression ratio for waste cooking oil methyl ester when compared to that of diesel. The brake thermal efficiency at 50% load for waste cooking oil methyl ester blends and diesel has been calculated and the blend B40 is found to give maximum thermal efficiency. The blends when used as fuel results in reduction of carbon monoxide, hydrocarbon and increase in nitrogen oxides emissions.     

Investigation on combustion and emission characteristics of hydrogen-enriched dual-fuel engine operated under waste frying oil biodiesel

Using nonedible waste frying oil (WFO) as biodiesel and hydrogen in the mix composition may partly replace significant quantities of diesel fuel and help reduce fossil fuel reliance. The combination of diesel fuel, waste-fired biodiesel, and hydrogen gas can improve the performance, combustion, and emissions of single-fuel and dual-fuel diesel engines. This may lead to a novel alternative fuel mix pattern and modification for diesel engines, which is the research gap. Although there has been some research on waste-fired biodiesel and hydrogen gas-powered dual-fuel engines with the goal of partly replacing fossil fuels to a larger degree, there has been very little progress in this area. As a result, the current research effort focuses on using diesel fuel (100%, 30%, and 60%), waste-fired biodiesel (at 100%, 70%, and 40%), and hydrogen gas as fuel sources (5 and 10 liters per minute [LPM]). According to the current experiment, it was perceived in both dual-fuel and single-fuel modes. Under duel-fuel mode, the engine results for WFOB70D30 + H10 fuel blend had higher 4.2% (brake thermal efficiency [BTE]), 19.72% (oxides of nitrogen [NO_x]), and 9.09% (ignition delay [ID]) with a minimal range of (in-cylinder pressure, MFB, volumetric efficiency and heat release rate [HRR]) and a dropped rate of 4.34% (brake-specific energy consumption [BSEC]), 33.33% (carbon monoxide [CO]), 39.28% (hydrocarbons [HC]), 9.43% (smoke), and 6.97% (combustion duration [CD]) related to diesel fuel at peak load. However, single-fuel powered diesel engines provide minimal performance for the WFOB40D60 fuel blend with (11.32% lower BTE and 2.04% higher BSEC) and minimal rate of combustion (lower cylinder pressure, 2.12% minimal CD, 14.72% higher ID, minimal HRR combustion, volumetric efficiency, and MFB). Emitted fewer emissions (9.09% less CO, 4.87% less HC, 0.92% higher NO_x, and 1.69% more smoke) than diesel fuel at peak load. Therefore, it was concluded that adding 10 LPM of hydrogen gas to the biodiesel under a dual-fuel condition leads to better combustion, better performance, and less pollution than the single-fuel mode of operation.     

Synergistic effect of hydrogen and waste lubricating oil on the performance and emissions of a compression ignition engine

The demand for energy is increasing every year. For a long time, fossil fuels have been used to satiate this energy demand. However, using hydrocarbon-based fossil fuels has led to an enormous rise of carbon dioxide levels in the atmosphere resulting in global warming. It is therefore necessary to look for alternatives to fossil fuels. The research carried out till date have shown biomass and waste-derived fuels as plausible alternatives to fossil fuels. The biomass feedstock includes jatropha oil, Karanja oil, cottonseed oil, and hemp oil among others and wastes include used cooking oil, used engine oil, used tire and used plastics etc. In this study, the authors aim to explore waste lubrication oil as a fuel for the diesel engine. The used lubrication oil was pyrolyzed and diesel-like fuel with 80% conversion efficiency was obtained. A blend of the fuel and diesel in the ratio of 80:20 on volume basis was prepared. Engine experiments at various load conditions was carried out with the blend. As compared to diesel, a 2% increase in thermal efficiency, 6.3%, 16.1% and 13.6% decrease in smoke, CO and HC emissions & 3.2% and 1.8% increase in NOx and CO₂ emission were observed at full load with the blend. With an aim to further improve the engine performance and reduce the overall emissions from the engine exhaust, a zero-carbon fuel namely gaseous hydrogen was inducted in the intake manifold. The flow rate of hydrogen was varied from 3 to 12 Litres per minute (LPM). As compared to diesel, at maximum hydrogen flow rate the thermal efficiency increased by 12.2%. HC, CO and smoke emissions decreased by 42.4%, 51.6% and 16.8%, whereas NOx emissions increased by 22%. The study shows that the combination of pyrolyzed waste lubricant and hydrogen were found to be suitable as a fuel for an unmodified diesel engine. Such fuel combination can be used for stationary applications such as power backups.     

Performance,emission and combustion characteristics of a compression ignition engine operating on neat orange oil

Biomass derived fuels are preferred as alternate fuels for I.C Engines due to their abundant availability and renewable nature. Fuels such as methanol and ethanol have proved to be suitable alternate fuels in the transport sector. In the present work the performance, emission and combustion characteristics of a single cylinder, constant speed, direct injection diesel engine using orange oil as an alternate fuel were studied and the results are compared with the standard diesel fuel operation. Results indicated that the brake thermal efficiency was higher compared to diesel throughout the load spectra. Carbon monoxide (CO) and hydrocarbon (HC) emissions were lower and oxides of nitrogen (NO_x) were higher compared to diesel operation. Peak pressure and heat release rate were found to be higher for orange oil compared to diesel fuel operation.     

Energy,exergy and emission analysis on a DI single cylinder diesel engine using pyrolytic waste plastic oil diesel blend

Depletion of fossil fuels and stringent emission norms focus attention to discover an evitable source of alternative fuel in order to attribute a significant compensation on conventional fuels. Besides, waste management policies encourage the valorization of different wastes for the production of alternative fuels in order to reduce the challenges of waste management. In this context, pyrolysis has become an emerging trend to convert different wastes into alternate fuel and suitable to be used as a substitute fuel for CI engines. The current investigation provides a sustainable and feasible solution for waste plastic management by widening the gap between global plastic production and plastic waste generation. It investigates the performance and emission of a single cylinder DI four stroke diesel engine using waste plastic oil (WPO) derived from pyrolysis of waste plastics using Zeolite-A as catalyst. Engine load tests have been conducted taking waste plastic oil and subsequently a blend of waste plastic oil by 10%, 20%, and 30% in volume proportions with diesel as fuel. The performance of the test engine in terms of brake thermal efficiency is found marginally higher and brake specific fuel consumption comparatively lowest for 20% WPO-diesel blend than pure diesel. The NOx and HC emission is found lower under low load condition and became higher by increasing the load as compared to diesel. Fuel exergy was significantly increasing after blending of WPO with pure diesel, but exergetic efficiency of the blended fuels followed the reverse trend. However, increase in load of the engine improved the exergetic efficiency. The 20% WPO–diesel blended fuel is found suitable to be used as an alternative fuel for diesel engine.     

Use of palm oil-based biofuel in the internal combustion engines: Performance and emissions characteristics

Palm oil (PO) was treated using different methods in order to use and test it as fuel in Compression Ignition (CI) engines. The treatments include PO preheated and preparation of PO/diesel oil blends, using mixtures of PO with waste cooking oil (WCO), which are converted into esters by a transesterification process. The purpose of this study is to evaluate the potential of the palm oil-based biofuels to replace diesel oil in CI engines.Tests were conducted in a single cylinder, four-stroke, air-cooled, direct injection diesel engine (no engine modifications were required). Experiments were initially carried out with diesel oil for providing baseline data. All the tested fuels have a low heating value compared to diesel fuel. A high fraction of PO in diesel fuel decreases the heating value of the blend. The brake thermal efficiency increases for the PO/Diesel blends. HC emissions for all those fuels except for the PO/Diesel blends are found lower, while CO emissions rise for all types of fuels. NO_x emissions are higher at low load, but lower at full load, for the engine fueled with PO and lower both at middle and full load for the engine fueled with the esters.     

A study of the performance,emission and combustion characteristics of a compression ignition engine using methyl ester of paradise oil–eucalyptus oil blends

The significance of this study is the complete replacement of diesel fuel with bio-fuels. For this purpose; bio-fuels, namely, methyl ester of paradise oil and eucalyptus oil were chosen and used as fuel in the form of blends. Various proportions of paradise oil and eucalyptus oil are prepared on a volume basis and used as fuels in a single cylinder, four-stroke DI diesel engine, to study the performance and emission characteristics of these fuels. In the present investigation a methyl ester derived from paradise oil is considered as an ignition improver. The results show a 49% reduction in smoke, 34.5% reduction in HC emissions and a 37% reduction in CO emissions for the Me50–Eu50 blend with a 2.7% increase in NO_x emission at full load. There was a 2.4% increase in brake thermal efficiency for the Me50–Eu50 blend at full load. The combustion characteristics of Me50–Eu50 blend are comparable with those of diesel.     

Experimental investigations on combustion, performance and emissions characteristics of neat karanji biodiesel and its methanol blend in a diesel engine

The increased focus on alternative fuels research in the recent years are mainly driven by escalating crude oil prices, stringent emission norms and the concern on clean environment. The processed form of vegetable oil (biodiesel) has emerged as a potential substitute for diesel fuel on account of its renewable source and lesser emissions. The experimental work reported here has been carried out on a turbocharged, direct injection, multi-cylinder truck diesel engine fitted with mechanical distributor type fuel injection pump using biodiesel-methanol blend and neat karanji oil derived biodiesel under constant speed and varying load conditions without altering injection timings. The results of the experimental investigation indicate that the ignition delay for biodiesel-methanol blend is slightly higher as compared to neat biodiesel and the maximum increase is limited to 1 deg. CA. The maximum rate of pressure rise follow a trend of the ignition delay variations at these operating conditions. However, the peak cylinder pressure and peak energy release rate decreases for biodiesel-methanol blend. In general, a delayed start of combustion and lower combustion duration are observed for biodiesel-methanol blend compared to neat biodiesel fuel. A maximum thermal efficiency increase of 4.2% due to 10% methanol addition in the biodiesel is seen at 80% load and 16.67 s⁻¹ engine speed. The unburnt hydrocarbon and carbon monoxide emissions are slightly higher for the methanol blend compared to neat biodiesel at low load conditions whereas at higher load conditions unburnt hydrocarbon emissions are comparable for the two fuels and carbon monoxide emissions decrease significantly for the methanol blend. A significant reduction in nitric oxide and smoke emissions are observed with the biodiesel-methanol blend investigated.     

Combustion and performance evaluation of a diesel engine fueled with biodiesel produced from soybean crude oil

In this study, the biodiesel produced from soybean crude oil was prepared by a method of alkaline-catalyzed transesterification. The important properties of biodiesel were compared with those of diesel. Diesel and biodiesel were used as fuels in the compression ignition engine, and its performance, emissions and combustion characteristics of the engine were analyzed. The results showed that biodiesel exhibited the similar combustion stages to that of diesel, however, biodiesel showed an earlier start of combustion. At lower engine loads, the peak cylinder pressure, the peak rate of pressure rise and the peak of heat release rate during premixed combustion phase were higher for biodiesel than for diesel. At higher engine loads, the peak cylinder pressure of biodiesel was almost similar to that of diesel, but the peak rate of pressure rise and the peak of heat release rate were lower for biodiesel. The power output of biodiesel was almost identical with that of diesel. The brake specific fuel consumption was higher for biodiesel due to its lower heating value. Biodiesel provided significant reduction in CO, HC, NO_x and smoke under speed characteristic at full engine load. Based on this study, biodiesel can be used as a substitute for diesel in diesel engine.     

A comprehensive study on performance,emission and combustion behavior of a compression ignition engine fuelled with WCO (waste cooking oil) emulsion as fuel

This work aims at evaluating the performance, emission and combustion of a diesel engine fuelled with WCO (waste cooking oil obtained from palm oil) and its emulsion as fuel. A single cylinder water-cooled diesel engine was used. Base data was generated with diesel and neat WCO as fuels. Subsequently, WCO oil was converted into its emulsion and tested. Neat WCO resulted in higher smoke, hydrocarbon and carbon monoxide emissions as compared to neat diesel. Significant reduction in all emission was achieved with the WCO emulsion. Cylinder peak pressure and maximum rate of pressure rise were found to be higher with WCO emulsion as compared to neat WCO mainly at high power outputs. Ignition delay was found as higher with neat WCO and its emulsion. It is concluded that WCO emulsion can be used in diesel engines without any modifications in the engine with superior performance and reduced emissions at high power outputs.     

The effect of mixed nanoadditive‐blended diesel–water emulsion on the performance,combustion, and emission characteristics of a DI diesel engine

The present paper examines the impact of mixed nanoadditive (Al₂O₃ and ZnO) incorporated diesel–water emulsion on the combustion, performance, and emission of a single‐cylinder diesel engine under varying load conditions. The test fuels consist of constant fuel ratio of 88% diesel, 10% water, and 2% surfactant. Also, different concentrations of mixed nanoadditives—50 ppm, 100 ppm, and 150 ppm—are added to the test fuel. The ultrasonicator bath is employed for agitation or stirring of test fuels. The test results indicate that the mixed nanoadditives in diesel–water emulsion improve combustion characteristics, brake thermal efficiency, and brake‐specific fuel consumption, whereas the maximum improvement is achieved at full load. It is also determined from the test results that the nanoadditive‐blended test fuel showed a noticeable decrement in CO, NO_x, and hydrocarbon emissions as compared with neat diesel. The optimum results are obtained for D88S2W10ZA150 blend. Owing to the higher surface‐to‐volume ratio, enhanced atomization rate, high catalytic behavior, and shortened ignition delay are possible reasons to improve diesel engine working characteristics.     

柴油机掺烧不同比例生物柴油的试验研究

将体积分数为10%2、0%、30%的生物柴油掺混到柴油里组成3种混合燃料,并连同纯柴油共4种燃料,在一台四缸增压中冷柴油机上进行性能、燃烧和排放特性的试验研究.结果表明,柴油机燃用生物柴油与柴油混合燃料的折合油耗率与燃用纯柴油时基本相当;燃用混合燃料的缸内最大爆发压力和压力升高率较低,着火时刻较晚;混合燃料的NOx和碳烟排放与燃用纯柴油时相比均有不同程度的降低,但混合燃料的HC和CO排放只是在1 500r/min时才较纯柴油低,当转速在2 300 r/min时,混合燃料的HC和CO排放更高.     

Performance and emission characteristics of diesel fuel produced from waste plastic oil obtained by catalytic pyrolysis of waste polypropylene

Waste plastic oil derived from kaoline catalyzed pyrolysis of waste polypropylene is blended with diesel fuel, tested as an alternative fuel in a diesel engine, and its performance characteristics are analyzed and compared with diesel fuel operation. It is observed that the engine could operate with maximum 50% waste plastic oil blended diesel. An engine showed better performance up to 30% blend, but beyond 50% blend it gave a vibration. The results showed a stable performance with brake thermal efficiency similar to that of diesel and its value is higher up to 80% of full load. All emissions are considerably higher than that of the diesel baseline especially at high load and blend.     

正丁醇/柴油发动机燃烧排放特性及喷油、燃烧室形状影响

针对某型号直喷柴油机,建立了该柴油机中单缸完整燃烧室及气道三维模型,使用三维计算流体力学(computational fluid dynamics,CFD)分析软件CONVERGE对其进行模拟计算,研究了正丁醇掺混比例对柴油机燃烧排放的影响。结果表明:随着正丁醇掺混比例的提高,峰值缸压、滞燃期和燃烧速度均呈递增趋势,碳烟及CO排放量逐渐减少,NO_x排放量小幅增加。为了进一步改善缸内燃烧情况和降低污染物排放,对正丁醇掺混时喷油策略、燃烧室几何形状的综合影响进行了研究,结果表明:掺混时多次喷油及采用合适的燃烧室模型可以有效改善掺混后缸内油气混合情况,增加缸内湍动能强度,进一步降低碳烟排放量。与纯柴油工况对比,掺混并采用多次喷油策略后碳烟排放明显下降,且通过掺混能够有效简化喷油策略,但弱化了燃烧室形状对碳烟排放量的影响。     

Experimental investigation on diesel engine with diestrol-water micro emulsions

Experiments were conducted on a single cylinder direct injection diesel engine using diesel, biodiesel and biodiesel-diesel-ethanol (diestrol) water micro emulsion fuels to investigate the performance, emission and combustion characteristics of the engine under different load conditions at a constant speed of 1500 rpm. The results indicated that biodiesel and micro emulsion fuels had a higher brake specific fuel consumption (BSFC) than that of diesel. A slight improvement in the brake specific energy consumption (BSEC) was observed for micro emulsion fuels. The brake thermal efficiency of biodiesel and micro emulsion fuels were comparable to that of diesel. The emission characteristics like carbon monoxide (CO), carbon dioxide (CO₂), unburnt hydrocarbon (UHC), nitric oxide (NO) and smoke emissions for biodiesel and micro emulsion fuels were lower than diesel fuel at all load conditions. The cylinder gas pressure of micro emulsion fuels was lower than diesel at low loads but it became almost identical to diesel at medium and full load conditions. The heat release rate for micro emulsion fuels was higher than biodiesel and diesel fuels for all loads. Biodiesel showed shorter ignition delay for the entire load range and the longer ignition delay observed for micro emulsion fuels.     

相同氧含量醇类混合燃料燃烧和排放特性差异研究

对一台4缸发动机燃用相同氧浓度的不同醇类混合燃料进行了试验研究,以对比不同三元燃料柴油机在相同转速不同负荷情况下的燃烧特性和常规排放的差异。试验结果表明:甲醇混合燃料在醇类混合燃料中获得最高的燃烧压力,而丁醇混合燃料的热释放率最高。与普通柴油相比,戊醇混合燃料在不同混合物中具有相对最佳的CO和未燃碳氢排放,甲醇混合燃料可获得最优的氮氧化物排放;乙醇混合燃料减小颗粒物效果明显,最大可以减少22.4%～55.6%的颗粒物数量浓度和3.4%～12.8%的颗粒物粒径,其中乙醇混合燃料的核态颗粒物和聚集态颗粒物排放量也最低,戊醇混合燃料达到最高(除高负荷外)。     

A study on the performance and emission of a diesel engine fueled with Jatropha biodiesel oil and its blends

Biodiesel either in neat form or as a mixture with diesel fuel is widely investigated to solve the twin problem of depletion of fossil fuels and environmental degradation. The main objective of the present study is to compare performance, emission and combustion characteristics of biodiesel derived from non edible Jatropha oil in a dual fuel diesel engine with base line results of diesel fuel. The performance parameters evaluated were: brake thermal efficiency, brake specific fuel consumption, power output. As a part of combustion study, in-cylinder pressure, rate of pressure rise and heat release rates were evaluated. The emission parameters such as carbon monoxide, carbon dioxide, un-burnt hydrocarbon, oxides of nitrogen and smoke opacity with the different fuels were also measured and compared with base line results. The different properties of Jatropha oil after transestrification were within acceptable limits of standards as set by many countries. The brake thermal efficiency of Jatropha methyl ester and its blends with diesel were lower than diesel and brake specific energy consumption was found to be higher. However, HC, CO and CO₂ and smoke were found to be lower with Jatropha biodiesel fuel. NO_x emissions on Jatropha biodiesel and its blend were higher than Diesel. The results from the experiments suggest that biodiesel derived from non edible oil like Jatropha could be a good substitute to diesel fuel in diesel engine in the near future as far as decentralized energy production is concerned. In view of comparable engine performance and reduction in most of the engine emissions, it can be concluded and biodiesel derived from Jatropha and its blends could be used in a conventional diesel engine without any modification.     

Studies on the effect of hydrogen induction on performance,emission and combustion behaviour of a WCO emulsion based dual fuel engine

This paper aims at studying the effect of hydrogen induction on engine performance, emission and combustion behaviour of a diesel engine fuelled with the emulsion of used palm oil (called as WCO-waste cooking oil) as pilot fuel and hydrogen as primary fuel. A single cylinder water-cooled direct injection diesel engine was tested at 100% and 40% loads. Results were compared with neat diesel, neat WCO and WCO emulsion at both loads in single fuel operation. WCO emulsion in single fuel mode indicated improvement in performance and reduction in all emissions as compared to neat WCO. Dual fuel operation with hydrogen induction further reduced the emissions of smoke HC and CO with WCO as pilot fuel at all power outputs. However, hydrogen induction resulted in reduced thermal efficiency at 40% load. WCO emulsion showed higher ignition delay as compared to neat WCO. Dual fuel operation with hydrogen induction increased the ignition delay further. Heat release pattern showed higher premixed combustion rate with hydrogen induction mainly at high power outputs. Premixed combustion rate became very high at higher rates of hydrogen admission mainly at high power output. In general, hydrogen induction showed superior performance at high power output and inferior performance at low power output with WCO emulsion as injected fuel.