Organic Thin Film Transistors Based on Highly Dipolar Donor–Acceptor Polymethine Dyes

Organic thin film transistors (OTFTs) of a series of twenty dipolar donor–acceptor‐substituted polymethine dyes (D–A dyes, dipole moments from 3–15 D) are investigated. The employed merocyanine dyes contain a dimethine bridge that is substituted with 1‐alkyl‐3,3‐dimethylindolin‐2‐ylidene (“Fischer base”), 3‐alkyl‐2,3‐dihydrobenzothiazol‐2‐ylidene or 1,3‐benzodithiole‐2‐ylidene, respectively, as electron‐donating unit and various acceptor heterocycles. These studies show that thin films formed by these D–A dyes upon deposition in high vacuum are all composed of antiparallel π‐stacked dimers. However, they are either amorphous, discontinuous or highly crystalline due to the interplay between molecule‐substrate and dimer–dimer interactions. With the help of single crystal X‐ray analysis, out‐of‐plane X‐ray studies (XRD), selected area electron diffraction (SAED), and atomic force microscopy (AFM), a correlation between the molecular structure, film ordering, and hole charge transport ability can be established. The mobility values are compared to Bässler's disorder charge transport theory and a film growth mechanism is proposed based on DFT calculations and single crystal structures. The results show that with carefully adjusted bulky substituents and high dipolarity an intimate centrosymmetric packing with a slipped, but tight π‐stacking arrangement could be realized. This provides two‐dimensional percolation pathways for holes and ultimately results in charge carrier mobilities up to 0.18 cm² V^?1 s^?1.     

Biocompatible D–A Semiconducting Polymer Nanoparticle with Light‐Harvesting Unit for Highly Effective Photoacoustic Imaging Guided Photothermal Therapy

The development of nanotheranostic agents that integrate diagnosis and therapy for effective personalized precision medicine has obtained tremendous attention in the past few decades. In this report, biocompatible electron donor–acceptor conjugated semiconducting polymer nanoparticles (PPor‐PEG NPs) with light‐harvesting unit is prepared and developed for highly effective photoacoustic imaging guided photothermal therapy. To the best of our knowledge, it is the first time that the concept of light‐harvesting unit is exploited for enhancing the photoacoustic signal and photothermal energy conversion in polymer‐based theranostic agent. Combined with additional merits including donor–acceptor pair to favor electron transfer and fluorescence quenching effect after NP formation, the photothermal conversion efficiency of the PPor‐PEG NPs is determined to be 62.3%, which is the highest value among reported polymer NPs. Moreover, the as‐prepared PPor‐PEG NP not only exhibits a remarkable cell‐killing ability but also achieves 100% tumor elimination, demonstrating its excellent photothermal therapeutic efficacy. Finally, the as‐prepared water‐dispersible PPor‐PEG NPs show good biocompatibility and biosafety, making them a promising candidate for future clinical applications in cancer theranostics.     

Manipulation of the Open‐Circuit Voltage of Organic Solar Cells by Desymmetrization of the Structure of Acceptor–Donor–Acceptor Molecules

The synthesis of acceptor–donor–acceptor (A–D–A) molecules based on a septithiophene chain with terminal electron acceptor groups is reported. Using a dicyanovinyl‐ (DCV) substituted molecule as reference, another symmetrical A–D–A donor containing thiobarbituric (TB) groups is synthesized and these two acceptor groups are combined to produce the unsymmetrical A–D–A′ compound. The electronic properties of the donors are analyzed by cyclic voltammetry and UV‐Vis absorption spectroscopy and their photovoltaic properties are characterized on bilayer planar heterojunction cells that include spun‐cast donor films and vacuum‐deposited C₆₀ as acceptor. Optical and electrochemical data show that replacement of DCV by TB leads to a small increase of the HOMO level and to a larger decrease of the LUMO, which result in a reduced band‐gap. The desymmetrized compound presents the lowest oxidation potential in solution but the highest oxidation onset in the solid state, which leads to a significant increase of the open‐circuit voltage of the resulting solar cells.     

Core–Satellite Mesoporous Silica–Gold Nanotheranostics for Biological Stimuli Triggered Multimodal Cancer Therapy

A core–satellite nanotheranostic agent with pH‐dependent photothermal properties, pH‐triggered drug release, and H₂O₂‐induced catalytic generation of radical medicine is fabricated to give a selective and effective tumor medicine with three modes of action. The nanocomplex (core–satellite mesoporous silica–gold nanocomposite) consists of amino‐group‐functionalized mesoporous silica nanoparticles (MSN‐NH₂) linked to L‐cysteine‐derivatized gold nanoparticles (AuNPs‐Cys) with bridging ferrous iron (Fe²⁺) ions. The AuNPs‐Cys serve as both removable caps that control drug release (doxorubicin) and stimuli‐responsive agents for selective photothermal therapy. Drug release and photothermal therapy are initiated by the cleavage of Fe²⁺ coordination bonds at low pH and the spontaneous aggregation of the dissociated AuNPs‐Cys. In addition, the Fe²⁺ is able to catalyze the decomposition of hydrogen peroxide abundant in cancer cells by a Fenton‐like reaction to generate high‐concentration hydroxyl radicals (·OH), which then causes cell damage. This system requires two tumor microenvironment conditions (low pH and considerable amounts of H₂O₂) to trigger the three therapeutic actions. In vivo data from mouse models show that a tumor can be completely inhibited after two weeks of treatment with the combined chemo‐photothermal method; the data directly demonstrate the efficiency of the MSN–Fe–AuNPs for tumor therapy.     

Toward the Prediction and Control of Glass Transition Temperature for Donor–Acceptor Polymers

Semiconducting donor–acceptor (D–A) polymers have attracted considerable attention toward the application of organic electronic and optoelectronic devices. However, a rational design rule for making semiconducting polymers with desired thermal and mechanical properties is currently lacking, which greatly limits the development of new polymers for advanced applications. Here, polydiketopyrrolopyrrole (PDPP)‐based D–A polymers with varied alkyl side‐chain lengths and backbone moieties are systematically designed, followed by investigating their thermal and thin film mechanical responses. The experimental results show a reduction in both elastic modulus and glass transition temperature (T_g) with increasing side‐chain length, which is further verified through coarse‐grained molecular dynamics simulations. Informed from experimental results, a mass‐per‐flexible bond model is developed to capture such observation through a linear correlation between T_g and polymer chain flexibility. Using this model, a wide range of backbone T_g over 80 °C and elastic modulus over 400 MPa can be predicted for PDPP‐based polymers. This study highlights the important role of side‐chain structure in influencing the thermomechanical performance of conjugated polymers, and provides an effective strategy to design and predict T_g and elastic modulus of future new D–A polymers.     

Architecture of Conjugated Donor–Acceptor (D–A)‐Type Polymer Films with Cross‐Linked Structures

A series of new donor–acceptor (D–A)‐type semiconducting conjugated polymers (SCPs), which can form cross‐linked structural and supramolecular assembly films by hydrogen‐bonding, is successfully synthesized. The microstructures of supramolecular assembly films are further investigated by X‐ray diffraction (XRD), high‐ resolution transmission electron microscopy (HRTEM), and variable‐temperature Fourier transform infrared (FT‐IR) absorption spectra. As electronic transmission (ET) materials, the SCPs demonstrate superior properties by means of fabricating electron‐only devices with the configuration of ITO/ET (SCPs)/Ca/Al. According to space‐charge‐limited current (SCLC) measurements, fluorine‐containing SCPs exhibit much smaller threshold voltages and much higher electron mobilities than Alq₃. Meanwhile, a significant enhancement for their luminescence properties is verified by the photoluminescence (PL) and electroluminescent (EL) spectra of cross‐linked‐type SCPs, compared to non‐cross‐linked‐type SCPs. The fabricated polymer light‐emitting diodes (PLEDs) with the configuration of ITO/PEDOT:PSS/EML (SCPs)/BCP/LiF/Al are able to emit the color from green to red with moderately low turn‐on voltages. These results suggested that cross‐linked D–A‐type SCP can become a potential candidate as a kind of multifunctional materials applied in the field of optoelectronic devices.     

Significant Improvement of Dye‐Sensitized Solar Cell Performance by Small Structural Modification in π‐Conjugated Donor–Acceptor Dyes

Two donor‐π‐acceptor (D‐π‐A) dyes are synthesized for application in dye‐sensitized solar cells (DSSC). These D‐π‐A sensitizers use triphenylamine as donor, oligothiophene as both donor and π‐bridge, and benzothiadiazole (BTDA)/cyanoacrylic acid as acceptor that can be anchored to the TiO₂ surface. Tuning of the optical and electrochemical properties is observed by the insertion of a phenyl ring between the BTDA and cyanoacrylic acid acceptor units. Density functional theory (DFT) calculations of these sensitizers provide further insight into the molecular geometry and the impact of the additional phenyl group on the photophysical and photovoltaic performance. These dyes are investigated as sensitizers in liquid‐electrolyte‐based dye‐sensitized solar cells. The insertion of an additional phenyl ring shows significant influence on the solar cells' performance leading to an over 6.5 times higher efficiency (η = 8.21%) in DSSCs compared to the sensitizer without phenyl unit (η = 1.24%). Photophysical investigations reveal that the insertion of the phenyl ring blocks the back electron transfer of the charge separated state, thus slowing down recombination processes by over 5 times, while maintaining efficient electron injection from the excited dye into the TiO₂‐photoanode.     

Yolk–Shell Structured Assembly of Bamboo‐Like Nitrogen‐Doped Carbon Nanotubes Embedded with Co Nanocrystals and Their Application as Cathode Material for Li–S Batteries

Despite their high theoretical specific capacity (1675 mA h g^?1), the practical application of Li–S batteries remains limited because the capacity rapidly degrades through severe dissolution of lithium polysulfide and the rate capability is low because of the low electronic conductivity of sulfur. This paper describes novel hierarchical yolk–shell microspheres comprising 1D bamboo‐like N‐doped carbon nanotubes (CNTs) encapsulating Co nanoparticles (Co@BNCNTs YS microspheres) as efficient cathode hosts for Li–S batteries. The microspheres are produced via a two‐step process that involves generation of the microsphere followed by N‐doped CNTs growth. The hierarchical yolk–shell structure enables efficient sulfur loading and mitigates the dissolution of lithium polysulfides, and metallic Co and N doping improves the chemical affinity of the microspheres with sulfur species. Accordingly, a Co@BNCNTs YS microsphere‐based cathode containing 64 wt% sulfur exhibits a high discharge capacity of 700.2 mA h g^?1 after 400 cycles at a current density of 1 C (based on the mass of sulfur); this corresponds to a good capacity retention of 76% and capacity fading rate of 0.06% per cycle with an excellent rate performance (752 mA h g^?1 at 2.0 C) when applied as cathode hosts for Li–S batteries.     

Bio‐Erasable Intermolecular Donor–Acceptor Interaction of Organic Semiconducting Nanoprobes for Activatable NIR‐II Fluorescence Imaging

Activatable second near‐infrared window (NIR‐II; 1.0–1.7 µm) fluorescence probes that uncage deep‐tissue penetrating fluorescence by disease‐related biomarker stimuli hold great promise for detecting diseases with a poor understanding of the pathology at the molecular level with unprecedented resolution. However, currently, very few activatable NIR‐II fluorescence probes are reported mainly due to the lack of a simple yet general design strategy. Herein, a new and fairly generic design strategy using a bio‐erasable intermolecular donor–acceptor interaction to construct activatable NIR‐II fluorescence probes is reported. An organic semiconducting nanoprobe (SPNP) is constructed through blending a biomarker‐sensitive organic semiconducting non‐fullerene acceptor (3,9‐bis(2‐methylene‐(3‐(1,1‐dicyanomethylene)‐cyclopentane‐1,3‐dione‐[c]thiophen))‐5,5,11,11‐tetrakis(4‐hexylphenyl)‐dithieno[2,3‐d:2',3'‐d']‐s‐indaceno[1,2‐b:5,6‐b'] dithiophene) (ITTC) (one of electric acceptors in organic solar cells) with a biomarker‐inert semiconducting polymer donor 5‐(4,8‐bis((2‐ethylhexyl)oxy)‐6‐methylbenzo[1,2‐b:4,5‐b']difuran‐2‐yl)‐10‐methylnaphtho[1,2‐c:5,6‐c']bis([1,2,5]thiadiazole) (PDF) in an amphiphilic‐polymer‐coated single nanoparticle to suppress NIR‐II fluorescence of the donor via a intermolecular donor–acceptor interaction. The acceptor ITTC is found to be specifically degraded by hypochlorite (an important biomarker) to erase its acceptor property, thus erasing the intermolecular donor–acceptor interaction and uncaging NIR‐II fluorescence. Consequently, SPNP exhibits a 17.5‐fold higher fluorescence brightness in the hypochlorite‐abnormal inflammation in vivo than in normal tissues. Our bio‐erasable intermolecular donor–acceptor interaction strategy provides simple yet general guidelines to design various biomarker‐activatable NIR‐II fluorescence probes.     

Robust Design of Dual‐Phasic Carbon Cathode for Lithium–Oxygen Batteries

Given that the performance of a lithium–oxygen battery (LOB) is determined by the electrochemical reactions occurring on the cathode, the development of advanced cathode nanoarchitectures is of great importance for the realization of high‐energy‐density, reversible LOBs. Herein, a robust cathode design is proposed for LOBs based on a dual‐phasic carbon nanoarchitecture. The cathode is composed of an interwoven network of porous metal–organic framework (MOF) derived carbon (MOF‐C) and conductive carbon nanotubes (CNTs). The dual‐phasic nanoarchitecture incorporates the advantages of both components: MOF‐C provides a large surface area for the oxygen reactions and a large pore volume for Li₂O₂ storage, and CNTs provide facile pathways for electron and O₂ transport as well as additional void spaces for Li₂O₂ accommodation. It is demonstrated that the synergistic nanoarchitecturing of the dual‐phasic MOF‐C/CNT material results in promising electrochemical performance of LOBs, as evidenced by a high discharge capacity of ≈10 050 mAh g^?1 and a stable cycling performance over 75 cycles.     

Camouflaging Nanoparticles with Brain Metastatic Tumor Cell Membranes: A New Strategy to Traverse Blood–Brain Barrier for Imaging and Therapy of Brain Tumors

Glioblastoma multiforme is one of the most fatal intracranial tumors with no effective treatment. The drug concentration in tumor sites is usually insufficient to reach therapeutic levels, due to poor blood–brain‐barrier (BBB) permeability and short biological half‐life. Inspired by the proneness of those malignant tumors to brain metastasis, a brain metastatic tumor cell membrane‐coated nanocarrier with core–shell structure is constructed to cross BBB for imaging and photothermal therapy of early brain tumors. The cell membranes as the shell are extracted from different metastatic tumor cells, which endow the nanoparticles with BBB‐crossing ability and long circulation. Indocyanine green (ICG)‐loaded polymeric nanoparticle as the core allows fluorescence imaging and phototherapy of brain tumors. The as‐prepared biomimetic nanoparticles display superb BBB penetration and effective suppression of tumor growth. These findings suggest the biomimetic nanotechnology provides a new insight for the design of BBB‐crossing nanomaterials and is promising to treat brain diseases.     

Sole Chemical Confinement of Polysulfides on Nonporous Nitrogen/Oxygen Dual‐Doped Carbon at the Kilogram Scale for Lithium–Sulfur Batteries

The exploration of inexpensive, facile, and large‐scale methods to prepare carbon scaffolds for high sulfur loadings is crucial for the advancement of Li–S batteries (LSBs). Herein, the authors report a new nitrogen and oxygen in situ dual‐doped nonporous carbonaceous material (NONPCM) that is composed of a myriad of graphene‐analogous particles. Importantly, NONPCM could be fabricated on a kilogram scale via inexpensive and green hydrothermal‐carbonization‐combined methods. Many active sites on the NONPCM surface are accessible for the efficient surface‐chemistry confinement of guest sulfur and its discharge product; this confinement is exclusive of physical entrapment, considering the low surface area. Electrochemical examination demonstrates excellent cycle stability and rate performance of the NONPCM (K)/S composite, even with a sulfur loading of 80 or 90 wt%. Hence, the scaffolds for LSBs exhibit potential for industrialization through further optimization and expansion of the present synthesis.     

Design of Hierarchical NiCo@NiCo Layered Double Hydroxide Core–Shell Structured Nanotube Array for High‐Performance Flexible All‐Solid‐State Battery‐Type Supercapacitors

A novel hierarchical nanotube array (NTA) with a massive layered top and discretely separated nanotubes in a core–shell structure, that is, nickel–cobalt metallic core and nickel–cobalt layered double hydroxide shell (Ni?Co@Ni?Co LDH), is grown on carbon fiber cloth (CFC) by template‐assisted electrodeposition for high‐performance supercapacitor application. The synthesized Ni?Co@Ni?Co LDH NTAs/CFC shows high capacitance of 2200 F g^?1 at a current density of 5 A g^?1, while 98.8% of its initial capacitance is retained after 5000 cycles. When the current density is increased from 1 to 20 A g^?1, the capacitance loss is less than 20%, demonstrating excellent rate capability. A highly flexible all‐solid‐state battery‐type supercapacitor is successfully fabricated with Ni?Co LDH NTAs/CFC as the positive electrode and electrospun carbon fibers/CFC as the negative electrode, showing a maximum specific capacitance of 319 F g^?1, a high energy density of 100 W h kg^?1 at 1.5 kW kg^?1, and good cycling stability (98.6% after 3000 cycles). These fascinating electrochemical properties are resulted from the novel structure of electrode materials and synergistic contributions from the two electrodes, showing great potential for energy storage applications.