Flow development in a gas-solids downer fluidized bed

The development of gas and solids flow structure was studied in a 9.5 m high and 0.10 m diameter, gas-solids cocurrent downflow circulating fluidized bed (downer). Local solids concentration and particle velocity were measured using two separate optical fibre probes at different radial positions on several axial levels along the downer. The results show that the flow development is significantly influenced by the operating conditions. For most of the conditions under which the experiments were conducted, the gas-solids flow reaches its fully developed zone within 3 to 8 m away from the entrance. On the other hand, the development zone can extend as long as the downer itself, under certain conditions. When the solids circulation rate is over 100 kg/m²s, an increasing solids circulation rate largely extends the length of radial flow development. It is found that the flow developments in the core and at the wall are not quite simultaneous. For solids concentration, the core develops more quickly at low gas velocities and the wall region develops faster at high gas velocities. For particle velocity, higher gas velocity speeds up the development of the wall region but does not significantly affect the development of the core region. The wall region is much more sensitive to the change of superficial gas velocity than the core region. At high superficial gas velocities (> 7 m/s), a “semi-dead” region is observed in the fully developed zone adjacent to the wall where the dilute solids are moving at a very low velocity.     

大型快速流化床内颗粒浓度和速度分布的实验研究

采用压力巡检仪和光纤测量仪,对直径300 mm的快速流化床反应器内气固两相流动特性进行了研究,考察了操作条件对快速床轴、径向催化剂颗粒浓度、颗粒速度、筛分分布等的影响. 结果表明,当操作气速提高到2.0~2.6 m/s,相应的催化剂循环强度在60~160 kg/(m2×s),床层密度可保持在50~650 kg/m3;催化剂颗粒浓度在径向上呈中心低、边壁高的不均匀分布,轴向上各径向位置在颗粒加速区逐渐降低、在充分发展区趋于稳定、随表观气速增大或催化剂循环强度减小而减小,且径向均匀性变好,在r/R<0.7的中心区域趋于一致;颗粒速度在径向上呈中心高、边壁低的抛物线形分布,且随操作气速增大或催化剂循环强度增大而更加明显.     

Position and velocity of a large particle in a gas/solid riser using the radioactive particle tracking technique

The flow behavior of the solids phase in the fully developed region of a laboratory-scale circulating fluidized bed riser was studied using an assembly of sixteen NaI detectors to determine the position of a 500 μm radioactive particle, 100 times/s. The particle location was inferred from the number of γ-rays recorded by the assembly. The knowledge of the instantaneous positions enabled the determination of the instantaneous and mean velocity fields. Tests were conducted in a 0.082 m diameter, 7 m tall riser using 150 μm silica sand particles. Data were obtained at a gas superficial velocity of 4 m/s and solids mass fluxes from 23 to 75 kg/m²·s. Radial profiles of axial particle velocity showed that the solids velocity decreased with increasing solids circulation rates. Correspondingly, turbulent particle velocities and solids dispersion coefficient in the longitudinal direction were found to decrease as the solids circulation rate increased. The cross-sectional area where, on average, solids downflow took place, increased with increasing solids circulation rate.     

循环流化床提升管中颗粒速度的径向分布及其沿轴向的发展

采用5光纤速度探头对f100mm?5.1m循环床提升管8个高度截面上11个径向位置的局部颗粒速度进行了实验测试,并采用径向不均匀指数(RNI)对颗粒速度径向分布的不均匀性及其沿轴向的变化进行了定量描述。研究结果表明:在高气速、高颗粒循环量操作时,操作条件对颗粒上升速度和下降速度的径向分布的影响在加速段和充分发展段呈现出不同的规律;颗粒上升速度和下降速度沿轴向的变化在核心区和边壁区也表现出不同的趋势。当颗粒循环速率大于200 kgm-2s-1时,颗粒的加速段长度大大延长,以至于大于提升管的高度(15.1m)。颗粒速度径向分布的不均匀性沿轴向是逐渐增大的,并且与截面平均颗粒速度存在很强的相关性。     

耦合流化床提升管内固含率径向分布及沿轴向的发展

针对催化汽油辅助反应器改质降烯烃工艺,结合提升管与流化床的特点,建立了一套提升管与流化床耦合反应器大型冷态实验装置. 在不同操作条件下,采用PV-4A型光纤密度仪测定了提升管内固含率沿径向的分布规律. 结果表明,固含率径向分布整体上呈现中心小、边壁大的环-核结构分布特征;沿轴向向上,各径向位置上的固含率在颗粒加速区逐渐降低,在充分发展区趋于稳定,在颗粒约束返混区又有所升高;各径向位置上的固含率随表观气速增大或颗粒循环强度减小而减小,且均匀性变好;提升管上部流化床内颗粒静床高度只对颗粒约束返混区内固含率径向分布有影响,而对颗粒加速区和充分发展区的固含率径向分布影响较小;当表观气速较低或颗粒循环强度较大时,颗粒约束返混区上部局部固含率最大值出现在无因次半径f=r/R=0.7附近,此时局部无因次固含率es*=es/ 沿轴向在H>5.33 m时不再具有相似性;通过比较径向不均匀指数,得到轴向各区固含率径向分布趋于均匀的程度依次为：充分发展区>颗粒约束返混区>颗粒加速区. 利用实验数据回归出了局部固含率径向分布关联式,其平均相对误差在6%以内.     

液固循环流化床中的颗粒速度场

利用超声多普勒测速仪（UDV）对液固循环流化床中颗粒流场进行了系统的实验研究.实验测定了不同轴向位置处的颗粒速度分布,得到了较完整的颗粒速度场,分析了入口区对流场分布的影响,考察了表观液速和颗粒循环速率等操作条件对颗粒速度场分布特点的影响,并利用各影响因素之间的相互关系对流型和速度的变化进行了分析.     

The influence of distributor structure on the solids distribution and flow development in circulating fluidized beds

The influence of distributor structure on solids distribution is studied in two riser circulating fluidized bed reactors with different distributor structures but similar diameters. Optic fibre probes were used for the measurement of local solids distribution. The axial and radial distribution of solids holdup in the riser with a multi‐tube distributor is more uniform than that with a multi‐orifice distributor. The radial profiles of particle velocity in the riser with the multi‐tube distributor are also more uniform than that with the multi‐orifice distributor. In the riser with the multi‐tube distributor, both gas and particles are distributed more uniformly across the section, so that the flow acceleration is much more uniform and faster. The flow development is much faster and the fully developed region is reached early for the riser with the multi‐tube distributor. The distributor design is an important factor for the design of circulating fluidized bed reactor.     

湍动流化床过渡段固含率分布特征的实验及数值模拟

在湍动流化床中,过渡段对于包括甲醇制烯烃在内的气固催化快反应有着重要的作用。采用PV6D反射型光纤探针对内径95 mm的湍动流化床内过渡段的固含率分布和脉动参数进行了测量,分别考察了表观气速和静床高的影响,并采用修正的基于颗粒动力学的三段曳力双流体模型进行模拟。实验表明,湍动流化床过渡段中固含率的轴向分布呈现S型和指数型两种类型,固含率轴向与径向分布都在过渡段内出现最大梯度,表明过渡段中固体浓度分布比稀相段和密相段更不均匀。表观气速和静床高的变化将导致S型和指数型分布的相互转变,并且对过渡段底部与壁面附近的固体高浓度区影响最为显著。局部固含率脉动概率密度分布表明,在静床高较小时,随着气速的增大,床层下部气含率最大值位置将从中心区移动至环隙区,呈现气含率的双峰型分布。本文提出的修正三段曳力模型考虑了颗粒团聚的影响,对过渡段中分布板影响区之外的固含率分布均能较好地模拟。     

Heat transfer study in a pilot-plant scale bubble column

The effects of superficial gas velocity on heat transfer coefficient and its time-averaged radial profiles along the bed height have been investigated in a pilot-plant scale bubble column of 0.44 m diameter using air-water system. Notable differences were observed in heat transfer coefficients along the bed axial locations particularly between the sparger (Z/D = 0.28) and the fully developed flow (Z/D = 4.8) regions. In the fully developed flow region larger heat transfer coefficient values were obtained compared to those in the sparger region. About 14-22% increase in heat transfer coefficients measured in the fully developed flow region has been observed compared to those measured in the distributor region when the superficial gas velocity increases from 0.05 to 0.45 m/s. The heat transfer coefficients in the column center for all the conditions studied are about 9-13% larger than those near the wall region. It has been noted that in the fully developed flow region, the axial variation of the heat transfer coefficients was not significant.     

Hydrodynamic modeling of a circulating fluidized bed

Hydrodynamics plays a crucial role in defining the performance of circulating fluidized beds (CFB). The numerical simulation of CFBs is very important in the prediction of its flow behavior. From this point of view, in the present study a dynamic two dimensional model is developed considering the hydrodynamic behavior of CFB. In the modeling, the CFB riser is analyzed in two regions: The bottom zone in turbulent fluidization regime is modeled in detail as two-phase flow which is subdivided into a solid-free bubble phase and a solid-laden emulsion phase. In the upper zone core-annulus solids flow structure is established. Simulation model takes into account the axial and radial distribution of voidage, velocity and pressure drop for gas and solid phase, and solids volume fraction and particle size distribution for solid phase. The model results are compared with and validated against atmospheric cold bed CFB units' experimental data given in the literature for axial and radial distribution of void fraction, solids volume fraction and particle velocity, total pressure drop along the bed height and radial solids flux. Ranges of experimental data used in comparisons are as follows: bed diameter from 0.05-0.418 m, bed height from 5-18 m, mean particle diameter from 67-520 μm, particle density from 1398 to 2620 kg/m³, mass fluxes from 21.3 to 300 kg/m²s and gas superficial velocities from 2.52-9.1 m/s.As a result of sensitivity analysis, the variation in mean particle diameter and superficial velocity, does affect the pressure especially in the core region and it does not affect considerably the pressure in the annulus region. Radial pressure profile is getting flatter in the core region as the mean particle diameter increases. Similar results can be obtained for lower superficial velocities. It has also been found that the contribution to the total pressure drop by gas and solids friction components is negligibly small when compared to the acceleration and solids hydrodynamic head components. At the bottom of the riser, in the core region the acceleration component of the pressure drop in total pressure drop changes from 0.65% to 0.28% from the riser center to the core-annulus interface, respectively; within the annulus region the acceleration component in total pressure drop changes from 0.22% to 0.11% radially from the core-annulus interface to the riser wall. On the other hand, the acceleration component weakens as it moves upwards in the riser decreasing to 1% in both regions at the top of the riser which is an important indicator of the fact that hydrodynamic head of solids is the most important factor in the total pressure drop.     

Solids motion and holdup profiles in liquid fluidized beds

Non-invasive gamma rays-based techniques, computer tomography and computer-aided radioactive particle tracking, were used to measure solid holdup and solid velocity profiles in liquid-solid fluidized beds. The time averaged velocity measurements indicated that multiple circulation cells exist in the column. The solid motion was upward in the center and downward near the walls in the fully developed part of the column. The flow pattern is reversed in the entry region of the column. The solid holdup values increase slightly with the increase in radial position in the fully developed region. The average values of holdup in the column were in agreement with other measurements and with the modified Richardson-Zaki equation. The solids mean velocities and eddy diffusivities increase with increase in liquid superficial velocity, column size, particle size and density. Distributor-type affects the mean velocity and turbulence parameters while the column height has a relatively minor effect. The solids motion and turbulence parameters presented here are useful for validation of CFD models.     

GAS-SOLIDS FLOW PATTERNS IN A CONCURRENT DOWNFLOW FAST FLUIDIZED BED(CDFFB)

Radial profiles of solid concentration and velocity for concurrent downward gas-solid suspension in a140mm inside diameter fast fluidized bed were investigated.The influence of gas velocity,solid circulating rateand axial position on radial profiles of solid concentration and particle velocity has been examined.It hasbeen found that an annular region of high solid concentration exists at r/R=0.94.At both the center and wallregion,the solid concentration and the particle velocities are relatively low.The shape of radial solid con-centration profile curves is mainly dependent on the cross-section averaged voidage,and the shape of radialparticle velocity profile is mainly affected by the gas velocity and cross-section averaged voidage.Based on the radial profiles of solid concentration and particle velocity,the solid mass flux profile and thenonuniformity of solids flow are discussed in this paper.It is shown that solids flow in CDFFB is much moreuniform than that in UFFB.     

Solids behaviour in a gas-solid two-phase mixture flowing through a packed particle bed

This paper reports the solids behaviour in a dilute gas-solid two-phase mixture flowing through a packed bed. The positron emission particle tracking (PEPT) technique was used in the work, which allowed investigation of three-dimensional solids motion at the single suspended particle level. Processing of the data gave solids velocity, the residence time of suspended particles, bed tortuosity in terms of solids motion, as well as solids occupancy in the cross-section of the packed bed. The results suggest that the wall effect on the motion of suspended particles is limited to approximately one packed particle diameter under the conditions of this work. Both the average axial and radial velocities of suspended particles, normalised by the superficial gas velocity, change periodically with radial position, but the periodicity does not correspond exactly to the packed particle diameter. The peak and trough values of the average axial velocity of the suspended particles in the bulk region are, respectively, ∼25% and ∼15% of the superficial gas velocity under the conditions of this work and the superficial gas velocity shows little effect. The peak and trough values of the average radial velocity of the suspended particles in the bulk region are, respectively, +5% (positive) and -5% (negative) of the superficial gas velocity. The results of the residence time and tortuosity of the suspended particles show an approximately Gaussian distribution with the peak residence time and tortuosity increasing with decreasing superficial gas velocity. The occupancy data suggest that particles spend more time in an annular region close to the wall, indicating a non-uniform particle distribution across the packed bed cross-section.     

提升管-流化床耦合反应器颗粒约束返混区的流动特性及约束作用分析

针对催化汽油辅助反应器改质降烯烃工艺,在一套提升管-流化床耦合反应器大型冷态实验装置上,系统研究了提升管出口段的颗粒流动特性,通过定义约束指数R_i（R_i为颗粒约束返混区实际截面平均固含率与理论截面平均固含率之比）定量反映提升管出口分布器及流化床层的约束作用。结果表明,与常规提升管相比,耦合反应器提升管出口存在一个颗粒约束返混区,其长度主要受表观气速、颗粒循环强度及上部流化床内颗粒静床高度影响;由于出口设置了倒锥形分布器,使得颗粒约束返混区靠近提升管出口区域在表观气速较低和颗粒循环强度较大时,局部固含率最大值出现在量纲 1半径Φ＝0.7处;颗粒约束返混区的约束指数在靠近出口的过程中逐渐增大,气固流动受到分布器及上部流化床层的约束作用亦逐渐增强。     

Comparative Study of Flow Structure in Circulating Fluidized Bed Risers with FCC and Sand Particles

The combined influences of particle properties and nozzle gas distributor design on the axial and radial flow structure in two 100 mm i.d., 15.1 m and 10.5 m long risers with FCC and sand particles were investigated by measuring the axial pressure gradient profiles, and the axial and radial profiles of solids concentration. The results show that the nozzle gas distributor design has significant effects on the axial and radial flow structure for the FCC and sand particles. At lower superficial gas velocity of less than 8.0 m/s, the upward gas‐solid flow of the sand particles decelerates in various degrees with the disappearing of the nozzle gas distributor effect. The upward gas‐solid flow of the FCC particles, however, occurs without noticeable deceleration within the range of this study. In the acceleration section, the radial distributions of the local solids concentration of the FCC particles are more uniform than those of sand particles under the same operating conditions; while in the fully developed zone, the sand particles have a more uniform radial distribution than the FCC particles. The gas‐solid flow is first developed in the center region, and then extends towards the wall. The overall flow development in the riser mainly depends on the local gas‐solid flow in the wall region.     

Lateral flux and velocity of FCC particles in a CFB riser

The radial profiles of the lateral solids mass flux and the lateral solids velocity were determined for FCC particles in a 7 m tall circulating fluidtzed bed riser 0.14 m in diameter by applying a lateral flux probe and electrical capacitance tomography. The external solids mass flux was varied between 148 and 302 kg/(m².s), while the superficial gas velocity was varied between 3.7 and 4.7 m/s. Under these conditions, a dense bottom region and an upper dilute region coexisted in the riser. Lateral fluxes in the dense bottom region reached 100 kg/(m².s) at the wall, but fell to 14 kg/(m².s) at the wall in the upper dilute region. At both axial locations, a net deposition of solids from the core to the annulus occurred, indicating that fully developed flow was never established under these conditions. The lateral fluxes in the bottom region were significantly larger than those found in previous studies. It was further concluded that considering the lateral solids flux to be only a function of solids concentration is an over‐simplification.     

鼓泡塔中气泡尺寸分布和局部气含率研究

在内径为0.38 m的鼓泡塔中采用双电导探针法对不同通气速率下的气泡尺寸分布和局部气含率进行了实验研究,分析了气泡尺寸的概率密度分布。结果表明:气泡尺寸随轴向高度的增加而增大,随径向距离增加而减小;鼓泡塔中气液流动可分为过渡流域和充分发展流域,在过渡流域气含率随轴向高度增加而增大,在充分发展流域气含率趋于均值,径向局部气含率分布呈抛物线型下降。高气速下气泡尺寸概率密度分布比低气速下宽,且随轴向高度的增加分布变宽。     

气固逆流下行流化床中颗粒速度的径向与轴向分布

在内径90 mm、高7 m的逆流下行床冷态实验装置中,研究了气固逆流下行床中循环锅炉灰(dp=300 mm)颗粒速度的径向分布及其沿轴向发展. 结果表明,局部颗粒速度沿径向分布是不均匀的,在完全发展区,颗粒速度中心和边壁低、在r/R=0.85附近颗粒速度最大. 由大量实验数据回归出预测充分发展段局部颗粒速度的关联式,该公式计算值与实验值的平均相对偏差小于±11%. 不同径向位置的局部颗粒速度沿轴向的变化趋势不同,边壁区域(r/R>0.622)颗粒速度沿轴向单调递增,而中心区域(0相似文献   

低密度循环流化床局部颗粒速度的轴径向分布的研究

在高8m,内径186mm的循环流化床中,利用光纤激光多普勒测速仪测量了FCC颗粒的局部速度沿轴径向的分布。实验结果表明:局部颗粒速度沿径向分布是不均匀的,床中心区域分布比较平坦,近壁环形区域分布较陡,颗粒沿轴向运动有较长的加速段。由实验数据回归得到预测低密度循环流化床局部颗粒速度的经验关联式。     

Local solid mixing in gas–solid fluidized beds

Diffusivity of the solid particles in a 152-mm ID gas–solid fluidized bed was determined at different regimes of fluidization. The gas was air at room temperature and atmospheric pressure and the solids were 385 μm sand or 70 μm FCC particles. The experiments were done at superficial gas velocities from 0.5 to 2.8 m/s for sand and 0.44 to 0.9 m/s for FCC (in both bubbling and turbulent regimes). Movement of a tracer was monitored by radioactive particle tracking (RPT) technique. Once the time-position data became available, local axial and radial diffusivity of solids were calculated from these data. Calculated diffusivities are in the range of 3.3×10⁻³ to 5.6×10⁻² m²/s for axial and 2.6×10⁻⁴ to 1.5×10⁻³ m²/s for radial direction. The results show that the diffusivities, both axial and radial, increase with superficial gas velocity and are linearly correlated to the axial solid velocity gradient. Solid diffusivity in a bed of FCC was found to be higher than that of a bed of sand at the same excess superficial gas velocity.