Effect of pin offset on the mechanical properties of friction stir welded AA 6013 aluminum alloy plates

In this study, AA 6013 aluminum plates were butt‐welded with friction stir welding via pin offset technique. Macrostructural observations revealed that kissing bonds, originated from the broken oxide layers, were found to occur in the welded joints. The fracture location of welded joints after tensile tests was found to be outside the joint area, revealing that kissing bonds which were formed in the stir zone exhibited no detrimental effect on the mechanical properties of joints. Microstructural observations revealed that phases belonging to Mg₂Si, Al₄Cu₂Mg₈Si₇ and Al(MnFe)Si were observed in the x‐ray diffraction pattern of friction stir welded joints. The highest tensile strength with a value of 206 MPa was achieved with the process parameters of 1.5 mm pin offset towards the advancing side and 500 min^?1 tool rotational speed, leading the ratio of tensile strength of joint to ultimate tensile strength of base metal, also known as joint efficiency, to reach 74 %.     

Friction stir welding of dissimilar aluminum alloys AA2219 to AA5083 – Optimization of process parameters using Taguchi technique

The joining of dissimilar Al–Cu alloy AA2219-T87 and Al–Mg alloy AA5083-H321 plates was carried out using friction stir welding (FSW) technique and the process parameters were optimized using Taguchi L₁₆ orthogonal design of experiments. The rotational speed, transverse speed, tool geometry and ratio between tool shoulder diameter and pin diameter were the parameters taken into consideration. The optimum process parameters were determined with reference to tensile strength of the joint. The predicted optimal value of tensile strength was confirmed by conducting the confirmation run using optimum parameters. This study shows that defect free, high efficiency welded joints can be produced using a wide range of process parameters and recommends parameters for producing best joint tensile properties. Analysis of variance showed that the ratio between tool shoulder diameter and pin diameter is the most dominant factor in deciding the joint soundness while pin geometry and welding speed also played significant roles. Microstructural studies revealed that the material placed on the advancing side dominates the nugget region. Hardness studies revealed that the lowest hardness in the weldment occurred in the heat-affected zone on alloy of 5083 side, where tensile failures were observed to take place.     

Effect of welding parameters on microstructure and mechanical properties of friction stir welded joints of AA7039 aluminum alloy

A high strength Al–Zn–Mg alloy AA7039 was friction stir welded by varying welding and rotary speed of the tool in order to investigate the effect of varying welding parameters on microstructure and mechanical properties. The friction stir welding (FSW) process parameters have great influence on heat input per unit length of weld, hence on temperature profile which in turn governs the microstructure and mechanical properties of welded joints. There exits an optimum combination of welding and rotary speed to produce a sound and defect free joint with microstructure that yields maximum mechanical properties. The mechanical properties increase with decreasing welding speed/ increasing rotary speed i.e. with increasing heat input per unit length of welded joint. The high heat input joints fractured from heat affected zone (HAZ) adjacent to thermo-mechanically affected zone (TMAZ) on advancing side while low heat input joints fractured from weld nugget along zigzag line on advancing side.     

Effect of friction stir welding on the microstructure and mechanical properties of AA 6063-T6 aluminum alloy

In this study, AA 6063-T6 alloy plates were joined via friction stir welding using three different pin geometries (i. e., helical threaded, pentagonal and triangular) under various process parameters of tool rotational speed and welding speed. The microstructures and mechanical properties of the various welded joints were investigated. Macro-structural observations revealed that kissing bonds occurred in the welded joints due to fractured oxide layers. X-ray diffraction analysis indicated that the stir zones of the welded joints exhibited phases of Al₈Fe₂Si, Al₅FeSi, and Mg₂Si. In the welded joints, processed using a helical threaded pin, no tunnel-type defect was detected to occur; specimens were fractured outside of the joint region during tensile tests, indicating that the kissing bonds formed in the stir zones did not cause any deterioration in tensile strength or ductility. The welded joints processed using a helical threaded, pentagonal and triangular pin at 500 min⁻¹ tool rotational speed and 80 mm min⁻¹ welding speed exhibited a ductile deformation behavior along with a tensile strength in the range of 153 MPa to 155 MPa.     

Effects of Tilt Angle on the Properties of Dissimilar Friction Stir Welding Copper to Aluminum

In the present investigation, dissimilar materials such as electrolytic tough pitch copper, and aluminum 6061-T651 were welded by friction stir welding technology. Effects of tool tilt angle on the mechanical and metallurgical properties were studied experimentally for dissimilar material systems. In the present study, the tool tilt angle was varied from 0° to 4° with an interval of 1°, while the other parameters such as rotational speed, welding speed, tool pin offset, and workpiece material position were kept constant. Macrostructure analysis, tensile test, macro hardness measurement, scanning electron microscopy, and energy dispersive x-ray spectrographic tests were performed to evaluate the weld properties of dissimilar copper–aluminum joints. The results revealed that a defect free dissimilar copper–aluminum friction stir welding was achieved by tilt angles 2°, 3°, and 4°. The maximum tensile strength was reported to be 117 MPa and the macro hardness was reported to be 181 VH (in the nugget zone) at a tilt angle of 4°. The macro hardness was increased as the tilt angle increases from 0° to 4°. In addition to this, the thermo-mechanically affected zone (at the copper side) was found to be the weakest zone for a dissimilar copper–aluminum friction stir welding system.     

Effect of tool rotational speed and pin profile on microstructure and tensile strength of dissimilar friction stir welded AA5083-H111 and AA6351-T6 aluminum alloys

The relatively new welding process friction stir welding (FSW) was applied in this research work to join 6 mm thick dissimilar aluminum alloys AA5083-H111 and AA6351-T6. The effect of tool rotational speed and pin profile on the microstructure and tensile strength of the joints were studied. Dissimilar joints were made using three different tool rotational speeds of 600 rpm, 950 rpm and 1300 rpm and five different tool pin profiles of straight square (SS), straight hexagon (SH), straight octagon (SO), tapered square (TS), and tapered octagon (TO). Three different regions namely unmixed region, mechanically mixed region and mixed flow region were observed in the weld zone. The tool rotational speed and pin profile considerably influenced the microstructure and tensile strength of the joints. The joint which was fabricated using tool rotational speed of 950 rpm and straight square pin profile yielded highest tensile strength of 273 MPa. The two process parameters affected the joint strength due to variations in material flow behavior, loss of cold work in the HAZ of AA5083 side, dissolution and over aging of precipitates of AA6351 side and formation of macroscopic defects in the weld zone.     

Influence of friction stir welding process and tool parameters on strength properties of AA7075-T6 aluminium alloy joints

The aircraft aluminium alloys generally present low weldability by traditional fusion welding process. The development of the friction stir welding has provided an alternative improved way of satisfactorily producing aluminium joints, in a faster and reliable manner. In this present work, the influence of process and tool parameters on tensile strength properties of AA7075-T₆ joints produced by friction stir welding was analysed. Square butt joints were fabricated by varying process parameters and tool parameters. Strength properties of the joints were evaluated and correlated with the microstructure, microhardness of weld nugget. From this investigation it is found that the joint fabricated at a tool rotational speed of 1400 rpm, welding speed of 60 mm/min, axial force of 8 kN, using the tool with 15 mm shoulder diameter, 5 mm pin diameter, 45 HRc tool hardness yielded higher strength properties compared to other joints.     

Tensile behavior of dissimilar friction stir welded joints of aluminium alloys

The heat treatable aluminium alloy AA2024 is used extensively in the aircraft industry because of its high strength to weight ratio and good ductility. The non-heat treatable aluminium alloy AA5083 possesses medium strength and high ductility and used typically in structural applications, marine, and automotive industries. When compared to fusion welding processes, friction stir welding (FSW) process is an emerging solid state joining process which is best suitable for joining these alloys. The friction stir welding parameters such as tool pin profile, tool rotational speed, welding speed, and tool axial force influence the mechanical properties of the FS welded joints significantly. Dissimilar FS welded joints are fabricated using five different tool pin profiles. Central composite design with four parameters, five levels, and 31 runs is used to conduct the experiments and response surface method (RSM) is employed to develop the model. Mathematical regression models are developed to predict the ultimate tensile strength (UTS) and tensile elongation (TE) of the dissimilar friction stir welded joints of aluminium alloys 2024-T6 and 5083-H321, and they are validated. The effects of the above process parameters and tool pin profile on tensile strength and tensile elongation of dissimilar friction stir welded joints are analysed in detail. Joints fabricated using Tapered Hexagon tool pin profile have the highest tensile strength and tensile elongation, whereas the Straight Cylinder tool pin profile have the lowest tensile strength and tensile elongation. The results are useful to have a better understanding of the effects of process parameters, to fabricate the joints with desired tensile properties, and to automate the FS welding process.     

The optimisation of process parameters for friction stir spot-welded AA3003-H12 aluminium alloy using a Taguchi orthogonal array

The aim of the present work is to optimise the welding parameters for friction stir spot welded non-heat-treatable AA3003-H12 aluminium alloy sheets using a Taguchi orthogonal array. The welding parameters, such as the tool rotational speed, tool plunge depth and dwell time, were determined according to the Taguchi orthogonal table L9 using a randomised approach. The optimum welding parameters for the peak tensile shear load of the joints were predicted, and the individual importance of each parameter on the tensile shear load of the friction stir spot weld was evaluated by examining the signal-to-noise ratio and analysis of variance (ANOVA) results. The optimum levels of the plunge depth, dwell time and tool rotational speed were found to be 4.8 mm, 2 s and 1500 rpm, respectively. The ANOVA results indicated that the tool plunge depth has the higher statistical effect with 69.26% on the tensile shear load, followed by the dwell time and rotational speed. The tensile shear load of the friction stir spot welding (FSSW) joints increased with increasing plunge depth. Additionally, examination of the weld cross-sections, microhardness tests and fracture characterisation of the selected friction spot welded joints were conducted to understand the better performance of the joints. All the fractures of the joints during tensile testing occurred at stir zone (SZ), where the bonded section was minimum. The tensile shear load and tensile deformation of the FSSW joints increased linearly with increasing the bonded size. The finer grain size in the SZ led to the higher hardness, which resulted in higher fracture strength. When the tensile shear load of the joints increased approximately 3-fold, the failure energy absorption of the joints increased approximately 15-fold.     

Eccentric-weave FSW between Cu and AA 6061-T6 with reinforced Graphene nanoparticles

This study deals with the retrofication of micro- and macrostructural defects in joining aluminum and copper alloy using eccentric weave friction stir welding. In addition, graphene nanoparticles were added to strengthen the weldments. Welding experiments were conducted with two types of stir tool as (normal and offset pin) in linear and eccentric weave pattern. Results from this study reveal the possibility of tool tribology on eccentric stirring with tool pin offset producing a very minimal wear of 5?µm in comparison to other patterns of weld; defects on microscopic and macroscopic view of the weldments prove the existence of fragmental cracks in eccentric welding, and mechanical properties viz. yield strength of 187?MPa, ultimate tensile strength of 217?MPa, and elongation of 10% were found for the eccentric weave welded joints. This reveals the achievement of robust welded joints in the aluminum and copper alloys by eccentric weave welding with pin offset.     

6061铝合金无倾角搅拌摩擦焊工艺及性能

目的 为了适应空间曲面构件的搅拌摩擦焊,开展6061铝合金无倾角搅拌摩擦焊工艺及性能的研究。方法 采用无倾角搅拌摩擦焊用的搅拌头,对5 mm厚6061-T6铝合金板材进行试验,研究焊缝成形及接头力学性能,并分析接头组织特征。结果 零倾角搅拌摩擦焊接头从组织上可区分为5个不同区域：焊核区(WNZ)、热力影响区(TMAZ)、热影响区(HAZ)、轴肩影响区(SAZ)和母材(BM);随着搅拌头转速增加,焊缝宽度和焊核尺寸均先变大后变小;随焊接速度增加,焊缝宽度和焊核尺寸均逐渐变小;当焊接速度固定时,随搅拌头转速增加,接头拉伸强度先增加后减小;当搅拌头转速固定时,随焊接速度增加,接头拉伸强度逐渐增大。结论 采用无倾角搅拌摩擦焊接方法,能够实现对5 mm厚6061-T6铝合金板材的有效焊接。     

Friction Stir Weldabilities of AA1050-H24 and AA6061-T6 Aluminum Alloys

The friction stir weldabilities of the strain-hardened AA1050-H24 and precipitate-hardened AA6061-T6 aluminum alloys were examined to reveal the effects of material properties on the friction stir welding behavior. The experimental results are obtlained. (1) For AA1050-H24, the weld can possess smoother surface ripples; there is no elliptical weld nugget in the weld; there is no discernible interface between the stir zone and the thermomechanically affected zone; and the internal defect of the weld looks like a long crack and is located in the lower part of the weld. (2) For AA6061-T6, the weld usually possesses slightly rougher surface ripples; an elliptical weld nugget clearly exists in the weld; there are discernible interfaces among the weld nugget, thermomechanically affected zone and heat affected zone; and the internal defect of the weld is similar to that of the AA1050-H24 weld. (3) The effective range of welding parameters for AA1050-H24 is narrow, while the one for AA6061-T6 is very wide. (4) T     

Analysis of dissimilar friction stir welding process for tensile properties of EN AW 2024 and EN AW 5083

The objective of the present study is to analyze the effect of dissimilar friction stir welding process parameters associated with the tool pin profile. Nine different welding experiments were conducted on EN AW 2024 and EN AW 5083 plates. Each of the welded joints was exposed to metallurgical and mechanical tests to determine the effect of the parameters on the welded joint's strength and characteristics. The welding responses or characteristics were analyzed using the statistical tools, grey relational analysis and analysis of variance. Thus, the contribution of each parameter to the process response (ultimate tensile strength and percentage of elongation) was analyzed, and an optimal welding condition was determined. The results of metallurgical analyses showed that the defective joints were mostly in the welded joints fabricated with a conical threaded pin, and the shape of the stir zone was affected by the pin profile and tool rotational speed. The metallurgical results were consistent with the tensile test results. Statistical analyses showed that the most effective parameter on the welded joint strength and elongation is tool rotational speed with 70.3 %. While the tool pin profile affects the stir zone shape, the strength and elongation are not affected. The effect of welding speed (5.6 %) is not significant on strength and elongation.     

Mechanical properties of friction stir butt‐welded Al‐5086 H32 plate

Al‐5086 H32 plates with a thickness of 3 mm were friction stir butt‐welded using different welding speeds at a tool rotational speed of 1600 rpm. The effect of welding speed on the weld performance of the joints was investigated by conducting optical microscopy, microhardness measurements and mechanical tests (i.e. tensile and bend tests). The effect of heat input during friction stir welding on the microstructure, and thus mechanical properties, of cold‐rolled Al‐ 5086 plates was also determined. The experimental results indicated that the maximum tensile strength of the joints, which is about 75 % that of the base plate, was obtained with a traverse speed of 200 mm/min at the tool rotational speed used, e.g. 1600 rpm, and the maximum bending angle of the joints can reach 180^o. The maximum ductility performance of the joints was, on the other hand, relatively low, e.g. about 20 %. These results are not unexpected due to the loss of the cold‐work strengthening in the weld region as a result of the heat input during welding, and thus the confined plasticity within the stirred zone owing to strength undermatching. Higher joint performances can also be achieved by increasing the penetration depth of the stirring probe in butt‐friction stir welding of Al‐5086 H32 plates.     

Microstructure and XRD analysis of FSW joints for copper T2/aluminium 5A06 dissimilar materials

Copper (T2) and aluminium alloy (5A06) were welded by friction stir welding (FSW). The microstructure, mechanical properties and phase constituents of FSW joints were studied by metallography, tensile testing machine and X-ray diffraction. The results indicated that the high quality weld joint could be obtained when tool rotational speed is 950 rpm, and travel speed is 150 mm/min. The maximum value of tensile strength is about 296 MPa. The metal Cu and Al close to copper side in the weld nugget (WN) zone showed a lamellar alternating structure characteristic. However, a mixed structure characteristic of Cu and Al existed in the aluminium side of weld nugget (WN) zone. There were no new Cu-Al intermetallic compounds in the weld nugget zone.     

Hybrid fuzzy-grey-Taguchi based multi weld quality optimization of Al/Cu dissimilar friction stir welded joints

Nowadays aluminum alloys substitute copper in various applications for weight reduction and cost savings. This paper presents fuzzy-grey Taguchi technique for optimization of friction stir welding condition with seven weld quality attributes of dissimilar Al/Cu joints with the minimum number of experiments for effective productivity and product quality. Taguchi's L₁₆ orthogonal array was used to conduct the experiments. Fuzzy inference system was adapted to convert the multi quality characteristics into an equivalent single quality parameter which was optimized by Taguchi approach. Four parameters namely, rotational speed of the tool, welding speed, plunging depth and tool pin offset were varied in four levels for investigating the effects on the process output like tensile strength, compressive strength, percentage of elongation, bending angle, weld bead thickness and average hardness at the nugget zone. The hardness profile is consistent with the variation of the structure within the nugget zone (NZ). Confirmation experiment was conducted using predicted optimum parameter setting and it showed that the proposed approach could efficiently optimize weld quality parameters. The microstructural analyses were also performed for all the zones of the joints at both Al and Cu sides. It revealed the finer grain size at the NZ compared to the base material due to dynamic recrystallization.     

Friction stir welding of dissimilar materials between AA6061 and AA7075 Al alloys effects of process parameters

Dissimilar AA6061 and AA7075 alloy have been friction stir welded with a variety of different process parameters. In particular, the effects of materials position and welding speed on the material flow, microstructure, microhardness distribution and tensile property of the joints were investigated. It was revealed that the material mixing is much more effective when AA6061 alloy was located on the advancing side and multiple vortexes centers formed vertically in the nugget. Three distinct zones with different extents of materials intercalations were identified and the formation mechanism of the three zones was then discussed. Grain refinement was observed in all three layers across the nugget zone with smaller grains in AA7075 Al layers. All the obtained joints fractured in the heat-affected zone on the AA6061 Al side during tensile testing, which corresponds very well to the minimum values in microhardness profiles. It was found that the tensile strength of the dissimilar joints increases with decreasing heat input. The highest joint strength was obtained when welding was conducted with highest welding speed and AA6061 Al plates were fixed on the advancing side. To facilitate the interpretation, the temperature history profiles in the HAZ and at zones close to TMAZ were also measured using thermocouple and simulated using a three-dimensional computational model.     

Predicting tensile strength,hardness and corrosion rate of friction stir welded AA6061-T6 aluminium alloy joints

AA6061-T₆ aluminium alloy (Al–Mg–Si alloy) has gathered wide acceptance in the fabrication of light weight structures requiring high strength-to-weight ratio and good corrosion resistance. The friction stir welding (FSW) process and tool parameters play major role in deciding the joint characteristics. In this research, the tensile strength and hardness along with the corrosion rate of friction-stir-butt welded joints of AA6061-T₆ aluminium alloy were investigated. The relationships between the FSW parameters (rotational speed, welding speed, axial force, shoulder diameter, pin diameter and tool hardness) and the responses (tensile strength, hardness and corrosion rate) were established. The optimal welding conditions to maximize the tensile strength and minimize the corrosion rate were identified and reported here.     

Influence of tool geometry and process parameters on macrostructure and static strength in friction stir spot welded polyethylene sheets

The effect of important welding parameters and tool properties that are effective on static strength in friction stir spot welds of polyethylene sheets were studied. Six different tool pin profiles (straight cylindrical, tapered cylindrical, threaded cylindrical, triangular, square and hexagonal) with different shoulder geometries, different pin length, pin angle and concavity angle were used to fabricate the joints. The tool rotational speed, tool plunge depth and dwell time were determined welding parameters. All the welding operations were done at the room temperature. Welding force and welding zone material temperature measurements were also done. Lap-shear tests were carried out to find the weld static strength. Weld cross section appearance observations were also done. From the experiments, the effect of pin profile, pin length, pin angle, dwell time and tool rotational speed on friction stir spot welding formation and weld strength was determined.     

Effect of welding parameters on microstructure and mechanical properties of AA7075‐T6 friction stir welded joints

The effects of advancing speed and rotational speed on the microstructure and the mechanical properties of friction stir welded 7075‐T6 aluminium alloy sheets were studied. The fatigue strength of sound joints was measured and compared to tensile testing results. Macrographs and microhardness maps were carried out to reveal the microstructure transformations. Fractographic observations were made to identify the failure mechanisms. The effects of welding parameters on the fatigue strength are discussed in terms of welding pitch k (mm/rev) and heat input (J/mm). At a high welding pitch, crack initiation at the root of the circular grooves left by the tool on the weld surface is the most detrimental failure mechanism. As the size and the depth of the grooves are related to the welding pitch, the fatigue strength increases when the welding pitch is reduced. However, when the heat input is excessive, the failure is caused by sub‐surface defects produced after abnormal stirring and/or by softening of the heat‐affected zone. Lateral lips on the weld surface edges also have an effect on the fatigue strength for intermediate welding pitch values.