余热驱动的有机朗肯循环-复叠式制冷系统?分析

针对余热的有效利用,建立了有机朗肯循环-复叠式制冷系统的热力学模型,其中:有机朗肯循环系统分别采用R123、R1234ze、R245fa、R600a、RC318、R141b等六种工质;复叠式制冷系统分别采用R22/R23、R404/R23、R290/R744、R717/R744等四种工质对。选择系统?效率作为性能评价指标,运用热力学第二定律研究系统运行参数对系统?效率的影响,分析了系统各部件的?损失,并指出了能量利用的薄弱环节,提出了有效提高系统性能的建议,为系统的优化提供参考。结果表明,对系统?效率而言,R141b和R717/R744是最佳工质。系统主要部件按?损失大小依次为凝汽器、膨胀机、高温级冷凝器、发生器、高温级压缩机、低温级蒸发器、蒸发冷凝器。尽可能提高压缩机的等熵效率,优化设计换热器的结构,减小传热温差,才能减少不可逆损失,提高换热器的?效率。     

R245fa有机朗肯循环余热发电系统火用分析

以低品位热能驱动的有机朗肯循环发电系统,是实现将低品位热能转变为电能,进而提高热力系统总体热效率,降低污染排放的有效途径之一。本文建立了低品位热能发电系统火用分析模型,对以R245fa为工质的温度低于383.15 K的低品位热能有机朗肯循环余热发电系统进行了火用分析,得到了各环节的能量转换效率并确定了对系统性能影响最大的环节;通过改变蒸发器和冷凝器的压降和传热系数值,分析了主要换热设备的设计和运行性能参数对系统火用效率、热效率和发电量的影响趋势,提出了低品位热能发电系统的优化方向。     

烟气驱动复叠式非共沸工质有机朗肯循环系统㶲分析

通过构建复叠式非共沸工质有机朗肯循环系统模型,并采用■分析方法,研究了系统■效率随工质摩尔组分的变化规律以及不同摩尔组分下,系统各部件■损失分布情况。研究结果表明:受蒸发器泡点温度与高温级蒸发器夹点位置影响,当高温级循环工质环戊烷摩尔分数为0.8,低温级循环工质异丁烷摩尔分数为0.1时,系统■效率取得最大值48.56%,比采用纯工质时相对提高了3.83%;且采用非共沸工质后,排烟损失、高温级蒸发器■损失、低温级冷凝器■损失均有显著降低。     

中温地热能驱动的跨临界有机朗肯-蒸气压缩制冷系统的火用分析

建立中温地热能驱动跨临界有机朗肯−蒸气压缩制冷系统的火用分析热力学模型,采用R143a作为系统循环工质,探讨膨胀机入口压力、地热流体进口温度、冷凝温度、蒸发温度对火用效率的影响规律,分析系统各个部件的火用损失。计算结果表明：合理的膨胀机入口压力应该小于1.8倍临界压力;存在最佳的地热流体进口温度使得系统的火用效率最大;降低冷凝温度和提高蒸发温度都可以提高?效率,但需要增加换热器等效换热面积作为代价;冷凝器、发生器、膨胀机、节流阀、压缩机、蒸发器、工质泵的火用损失依次降低;随着地热流体进口温度升高,冷凝器及发生器的火用损失所占的比例增大,其它部件的火用损失对应的比例则降低。本文可以为跨临界有机朗肯−蒸气压缩制冷系统的设计提供依据。     

甘孜地热发电能量分析与火用分析

本文对四川甘孜的一口地热井进行能量分析和?分析,参考该井地热水的温度115℃,采取的发电方式有单级闪蒸系统、预热有机朗肯系统、闪蒸有机朗肯联合系统。结果表明,闪蒸朗肯系统的?效率最高（47.81%）,预热朗肯系统次之（46.31%）,单级闪蒸系统最低（42.83%）。对于有机朗肯循环,发生器的影响因子及?损均为最大;而闪蒸部分,闪蒸罐的影响因子最高,但闪蒸朗肯系统将其?损减少64.8%,低于汽轮机。计算结果显示,提高闪蒸/发生温度能够提高效率、减少?损,而闪蒸朗肯系统中发生温度有较好的优化性能。综上所述,闪蒸有机朗肯联合系统具有最大的净功率（360.8 kW）和最高的?效率,而且尾水温度最低,热效率适中,适合用于中低温地热发电。     

空气源热泵空调系统节能分析

节能的分析及优化已不仅仅是能的量的问题，而是能的质与量的综合评价的问题。采用yong分析方法得出空气源热泵空调系统的能耗分布，明确系统yong损失较大的环节。从yong分析得知：压缩机的yong损失占机组能耗的20．5％，冷凝器的yong损失接近总能耗的30％。由此提出了空气源热泵空调系统的节能措施，即应该选用高效率的压缩机，采用强化传热措施，提高传热系数，减小传热温差，同时还应注意改善热泵机组的周围环境，使系统yong损失最小，yong效率最大，实现空气源热泵空调系统的节能优化.     

Experimental investigation of a scroll expander for an organic Rankine cycle

This paper presents experimental investigation of the performance of an organic Rankine cycle (ORC) with scroll expander which utilizes renewable, process and waste heats. An ORC test bench is built with a scroll expander‐generator unit modified from a refrigeration compressor‐electrical drive unit. A detailed experimental investigation within the test bench is performed with the organic working fluid R134a. The results show that scroll expander can effectively be used in low‐power ORC to generate mechanical work or electricity from low‐temperature thermal sources (e.g. 80–200 °C, respectively). The experiments are performed under fixed intake conditions into the expander. The pressure ratio and the load connected to the expander‐generator unit were varied. It is found that an optimum pressure ratio and an optimum angular speed co‐exist. When operating optimally, the expander's isentropic efficiency is the highest. The optimum angular speed is around 171 rad/s which corresponds to a generated voltage of 18.6 V. The optimum pressure ratio is about 4. The isentropic efficiency at optimum operation is found in the range of 0.5 to 0.64, depending on the intake conditions. The volumetric efficiency overpasses 0.9 at optimum operation and degrades significantly if the load is increased over the optimum load. A regenerative ORC equipped with the studied expender‐generator unit that operates under 120 °C heat source and has an air cooled condenser generates 920 W net power with efficiencies of 8.5% energetically and 35% exergetically. Copyright © 2014 John Wiley & Sons, Ltd.     

太阳能喷射式制冷功冷联供系统

以太阳能为驱动热源,基于喷射式制冷和ORC,构建一种太阳能喷射式制冷功冷联供系统,该系统分为太阳能集热子系统和功冷联供子系统两部分。以R161为功冷联供子系统循环工质,通过Matlab建立该系统热力学模型,对其性能进行模拟,在设计工况下该系统制冷量为2.893 kW,净输出功为1.594 kW,功冷联供子系统制冷效率为12.47%,发电效率为6.87%,效率为41.45%。通过分析可知,该系统损占比较大的部件依次为太阳能集热器（73.3%）、发生器（12.14%）、蒸发器（5.03%）和透平（4.81%）。考虑到实际过程,分别研究系统内部参数改变和外部环境参数改变,对系统的影响,发现高低压发生器的温升由利于系统性能的提升,同时环境温度的升高以及太阳辐照度的提升均可改善集热器效率,从而提升系统性能。     

Exergy analysis of a coal‐based 210 MW thermal power plant

In the present work, exergy analysis of a coal‐based thermal power plant is done using the design data from a 210 MW thermal power plant under operation in India. The entire plant cycle is split up into three zones for the analysis: (1) only the turbo‐generator with its inlets and outlets, (2) turbo‐generator, condenser, feed pumps and the regenerative heaters, (3) the entire cycle with boiler, turbo‐generator, condenser, feed pumps, regenerative heaters and the plant auxiliaries. It helps to find out the contributions of different parts of the plant towards exergy destruction. The exergy efficiency is calculated using the operating data from the plant at different conditions, viz. at different loads, different condenser pressures, with and without regenerative heaters and with different settings of the turbine governing. The load variation is studied with the data at 100, 75, 60 and 40% of full load. Effects of two different condenser pressures, i.e. 76 and 89 mmHg (abs.), are studied. Effect of regeneration on exergy efficiency is studied by successively removing the high pressure regenerative heaters out of operation. The turbine governing system has been kept at constant pressure and sliding pressure modes to study their effects. It is observed that the major source of irreversibility in the power cycle is the boiler, which contributes to an exergy destruction of the order of 60%. Part load operation increases the irreversibilities in the cycle and the effect is more pronounced with the reduction of the load. Increase in the condenser back pressure decreases the exergy efficiency. Successive withdrawal of the high pressure heaters show a gradual increment in the exergy efficiency for the control volume excluding the boiler, while a decrease in exergy efficiency when the whole plant including the boiler is considered. Keeping the main steam pressure before the turbine control valves in sliding mode improves the exergy efficiencies in case of part load operation. Copyright © 2006 John Wiley & Sons, Ltd.     

小龙潭电厂300MW机组热力系统(火用)分析

应用能量平衡和(火用)分析方法,对小龙潭火力发电厂300MW机组热力系统能量转换过程进行了定量计算,分析了各个单元的能量有效利用及损失情况,指出了损失的主要部位和原因.结果表明:热量损失主要发生在凝汽器单元,凝汽器散失到周围环境中的热量为411.28 MW,占输入热量的51.57%,锅炉单元散失的热量为52.96 MW,占输入热量的6.64%,汽轮机单元散失的热量为20.40 MW,占输入热量的2.56%;(火用)损主要发生在锅炉单元,锅炉、汽轮机和凝汽器单元的(火用)损分别占输入(火用)的67.78%、18.54%和13%;锅炉中燃料燃烧及大温差传热是整个系统不可逆的主要原因;不同工况下每个单元的(火用)损和(火用)效率会随着环境温度适度改变,但同一工况下机组总的(火用)效率不随环境温度变化.     

Exergy Analysis of Electric Vehicle Heat Pump Air Conditioning System with Battery Thermal Management System

The exergy analysis of an electric vehicle heat pump air conditioning system(HPACS) with battery thermal management system was carried out by studying the exergy loss of each component. The results indicate that the compressor is the main source of system exergy loss in all operation conditions. The exergy loss distribution of HPACS is almost the same when the battery thermal management system integrated into the HPACS in cabin and battery mixed cooling mode and the system exergy loss was linear...     

有机工质低温余热发电系统多目标优化设计

针对现有有机朗肯循环单目标优化设计的局限性,从热力性、经济性等多方面对有机工质低温余热发电系统进行多目标优化设计.以系统效率最大和总投资费用最小为目标函数,选取透平进口温度、透平进口压力、余热锅炉节点温差、接近点温差和冷凝器端差等5个关键热力参数作为决策变量,利用非支配解排序遗传算法(NSGA-II)分别对采用R123、R245fa和异丁烷的有机工质余热发电系统进行多目标优化,获得不同工质的多目标优化的最优解集(Pareto最优前沿),并采用理想点辅助法从最优解集中选择出最优解及相应的系统最佳热力参数组合.结果表明:在给定余热条件下,从热力性能和经济性两方面考虑,R245fa是最优的有机工质,从多目标优化的最优解集中选择出的最佳效率为10.37%,最小总投资费用为455.84万元.     

船舶垃圾焚烧炉及柴油动力装置余热综合利用系统

从船舶节能角度出发,提出了一种综合利用船舶垃圾焚烧炉及柴油动力装置余热的回收系统。对系统各部件和工质参数进行计算,为设备设计和选型提供依据;对系统进行?平衡和热平衡计算,系统中锅炉的?损失最大为68.1%,冷凝器的?损失最小为3.17%;对系统进行经济性分析,结果表明系统能量利用率εE提高了3.54%,动力装置有效热效率ηe提高了3.11%,系统获得额外约1300（万元/年）的收益,投资回收期约为1.6年,对该余热回收系统进行投资是切实可行的。     

压水堆核电机组热力系统炯损分布的矩阵算法

基于火（用）分析法和矩阵算法,建立了压水堆核电机组热力系统的通用火（用）损分布矩阵方程,并以某900MW压水堆核电机组为例进行了计算分析,得到了额定工况下热力系统及设备的焖损分布规律．结果表明：反应堆的焖损失最大,占核能总火（用）的50．85％,其次为汽轮发电机、蒸汽发生器和凝汽器,分别占核能总火（用）的6．17％、3．2％和2．55％;矩阵方程较常规火（用）分析法具有构造简单、矩阵元素填写法则简便、物理意义明确和规律性强等优点;利用该方程便于开发出相应的计算程序,进而为核电机组节能潜力挖掘和故障诊断提供依据．     

SECOND LAW ANALYSIS OF A SOLAR THERMAL POWER SYSTEM

This communication presents second law analysis based on exergy concept for a solar thermal power system. Basic energy and exergy analysis for the system components (viz. parabolic trough collector/receiver and Rankine heat engine etc.) are carried out for evaluating the energy and exergy losses as well as exergetic efficiency for typical solar thermal power system under given operating conditions. Relevant energy flow and exergy flow diagrams are drawn to show the various thermodynamic and thermal losses. It is found that the main energy loss takes place at the condenser of the heat engine part whereas the exergy analysis shows that the collector-receiver assembly is the part where the losses are maximum. The analysis and results can be used for evaluating the component irreversibilities which can also explain the deviation between the actual efficiency and ideal efficiency of solar thermal power system.     

Energy,exergy and exergo-environmental impact assessment of a solid oxide fuel cell coupled with absorption chiller & cascaded closed loop ORC for multi-generation

A novel solid oxide fuel cell (SOFC) multigeneration system fueled by biogas derived from agricultural waste (maize silage) is designed and analyzed from the view point of energy and exergy analysis. The system is proposed in order to limit the greenhouse gas emissions as it uses a renewable energy source as a fuel. Electricity, domestic hot water, hydrogen and cooling load are produced simultaneously by the system. The system includes a solid oxide fuel cell; which is the primary mover, a biogas digester subsystem, a cascaded closed loop organic Rankine cycle, a single effect LiBr-water absorption refrigeration cycle, and a proton exchange membrane electrolyzer subsystem. The proposed cascaded closed-loop ORC cycle is considered as one of the advanced heat recovery technologies that significantly improve thermal efficiency of integrated systems. The thermal performance of the proposed system is observed to be higher in comparison to the simple ORC and the recuperated ORC cycles. The integration of a splitter to govern the flue gas separation ratio is also introduced in this study to cater for particular needs/demands. The separation ratio can be used to vary the cooling load or the additional power supplied by the ORC to the system. It is deduced that net electrical power, cooling load, heating capacity of the domestic hot water and total energy and exergy efficiency are 789.7 kW, 317.3 kW, 65.75 kW, 69.86% and 47.4% respectively under integral design conditions. Using a parametric approach, the effects of main parameters on the output of the device are analyzed. Current density is an important parameter for system performance. Increasing the current density leads to increased power produced by the system, decreased exergy efficiency in the system and increased energy efficiency. After-burner, air and fuel heat exchangers are observed to have the highest exergy destruction rates. Lower current density values are desirable for better exergy-based sustainability from the exergetic environmental impact assessment. Higher current density values have negative effect on the environment.     

An examination of exergy destruction in organic Rankine cycles

The exergy topological method is used to present a quantitative estimation of the exergy destroyed in an organic Rankine cycle (ORC) operating on R113. A detailed roadmap of exergy flow is presented using an exergy wheel, and this visual representation clearly depicts the exergy accounting associated with each thermodynamic process. The analysis indicates that the evaporator accounts for maximum exergy destroyed in the ORC and the process responsible for this is the heat transfer across a finite temperature difference. In addition, the results confirm the thermodynamic superiority of the regenerative ORC over the basic ORC since regenerative heating helps offset a significant amount of exergy destroyed in the evaporator, thereby resulting in a thermodynamically more efficient process. Parameters such as thermodynamic influence coefficient and degree of thermodynamic perfection are identified as useful design metrics to assist exergy‐based design of devices. This paper also examines the impact of operating parameters such as evaporator pressure and inlet temperature of the hot gases entering the evaporator on ORC performance. It is shown that exergy destruction decreases with increasing evaporator pressure and decreasing turbine inlet temperatures. Finally, the analysis reveals the potential of the exergy topological methodology as a robust technique to identify the magnitude of irreversibilities associated with real thermodynamic processes in practical thermal systems. Copyright © 2008 John Wiley & Sons, Ltd.     

Exergetical analysis of organic flash cycle with two-phase expander for recovery of finite thermal reservoirs

In this work exergetical performance analysis is carried out based on the second law of thermodynamics for organic flash cycle（OFC） using a two-phase expander instead of throttle expansion in order to recover efficiently finite thermal reservoirs.The exergy destructions（anergies） at various components of the system are theoretically investigated as well as the exergy efficiency.Results show that the anergy of heat exchanger or two-phase expander decreases while the anergy of throttle valve increases with increasing flash temperature,and the exergy efficiency has an optimum value with respect to the flash temperature.Under the optimal conditions with respect to the flash temperature,exergy efficiency increases with the heating temperature and the component having the largest exergy destruction varies with the flash temperature or heating temperature.     

Energy,exergy and exergoeconomic analysis of a steam power plant: A case study

The objective of this paper is to perform the energy, exergy and exergoeconomic analysis for the Hamedan steam power plant. In the first part of the paper, the exergy destruction and exergy loss of each component of this power plant is estimated. Moreover, the effects of the load variations and ambient temperature are calculated in order to obtain a good insight into this analysis. The exergy efficiencies of the boiler, turbine, pump, heaters and the condenser are estimated at different ambient temperatures. The results show that energy losses have mainly occurred in the condenser where 306.9 MW is lost to the environment while only 67.63 MW has been lost from the boiler. Nevertheless, the irreversibility rate of the boiler is higher than the irreversibility rates of the other components. It is due to the fact that the combustion reaction and its high temperature are the most significant sources of exergy destruction in the boiler system, which can be reduced by preheating the combustion air and reducing the air–fuel ratio. When the ambient temperature is increased from 5 to 24°C, the irreversibility rate of the boiler, turbine, feed water heaters, pumps and the total irreversibility rate of the plant are increased. In addition, as the load varies from 125 to 250 MW (i.e. full load) the exergy efficiency of the boiler and turbine, condenser and heaters are increased due to the fact that the power plant is designed for the full load. In the second part of the paper, the exergoeconomic analysis is done for each component of the power plant in order to calculate the cost of exergy destruction. The results show that the boiler has the highest cost of exergy destruction. In addition, an optimization procedure is developed for that power plant. The results show that by considering the decision variables, the cost of exergy destruction and purchase can be decreased by almost 17.11%. Copyright © 2008 John Wiley & Sons, Ltd.     

Performance comparison and parametric optimization of subcritical Organic Rankine Cycle (ORC) and transcritical power cycle system for low-temperature geothermal power generation

Organic Rankine Cycle (ORC) is a promising technology for converting the low-grade energy to electricity. This paper presents an investigation on the parameter optimization and performance comparison of the fluids in subcritical ORC and transcritical power cycle in low-temperature (i.e. 80–100 °C) binary geothermal power system. The optimization procedure was conducted with a simulation program written in Matlab using five indicators: thermal efficiency, exergy efficiency, recovery efficiency, heat exchanger area per unit power output (APR) and the levelized energy cost (LEC). With the given heat source and heat sink conditions, performances of the working fluids were evaluated and compared under their optimized internal operation parameters. The optimum cycle design and the corresponding operation parameters were provided simultaneously. The results indicate that the choice of working fluid varies the objective function and the value of the optimized operation parameters are not all the same for different indicators. R123 in subcritical ORC system yields the highest thermal efficiency and exergy efficiency of 11.1% and 54.1%, respectively. Although the thermal efficiency and exergy efficiency of R125 in transcritical cycle is 46.4% and 20% lower than that of R123 in subcritical ORC, it provides 20.7% larger recovery efficiency. And the LEC value is relatively low. Moreover, 22032L petroleum is saved and 74,019 kg CO₂ is reduced per year when the LEC value is used as the objective function. In conclusion, R125 in transcritical power cycle shows excellent economic and environmental performance and can maximize utilization of the geothermal. It is preferable for the low-temperature geothermal ORC system. R41 also exhibits favorable performance except for its flammability.