Temperature dependence of the band structure of 3<Emphasis Type="Italic">C</Emphasis>, 2<Emphasis Type="Italic">H</Emphasis>, 4<Emphasis Type="Italic">H</Emphasis>, and 6<Emphasis Type="Italic">H</Emphasis> SiC polytypes

The temperature dependences of significant energy extrema at the high-symmetry points Γ, X, L, K, M, A, and H of the Brillouin zone in the cubic and hexagonal modifications of SiC, as well as the energies of the main interband transitions at these points, were calculated for the first time by the empirical-pseudopotential method. The effect of the temperature dependence of the electron-phonon interaction on the crystal band structure was taken into account via the Debye-Waller factors, and the contribution of the linear expansion of the lattice was accounted for via the temperature dependence of the linear-expansion coefficient. The special features of the temperature dependences of the energy levels and of energies of the interband and intraband transitions are analyzed in detail. The results of the calculations are in good agreement with the known experimental data on the characteristics of SiC-based p-n structures operating in the breakdown mode. For example, the temperature coefficient of the energy of the X_1c–X_3c transition, which is responsible for the narrow violet band in the breakdown-electroluminescence spectra of reverse-biased p-n junctions, was found to be significantly smaller than the temperature coefficients for the interband transitions (from the conduction to valence band). This fact is quite consistent with the experimental curve of the temperature coefficient of the emission spectrum, which has a minimum in the same wavelength range.     

High-efficiency LEDs based on <Emphasis Type="Italic">n</Emphasis>-GaSb/<Emphasis Type="Italic">p</Emphasis>-GaSb/<Emphasis Type="Italic">n</Emphasis>-GaInAsSb/<Emphasis Type="Italic">P</Emphasis>-AlGaAsSb type-II thyristor heterostructures

A new type of light-emitting diodes (LEDs), a high-efficiency device based on an n-GaSb/p-GaSb/n-GaInAsSb/P-AlGaAsSb thyristor heterostructure, with the maximum emission intensity at wavelength λ = 1.95 μm, has been suggested and its electrical and luminescent characteristics have been studied. It is shown that the effective radiative recombination in the thyristor structure in the n-type GaInAsSb active region is provided by double-sided injection of holes from the neighboring p-type regions. The maximum internal quantum efficiency of 77% was achieved in the structure under study in the pulsed mode. The average optical power was as high as 2.5 mW, and the peak power in the pulsed mode was 71 mW, which exceeded by a factor of 2.9 the power obtained with a standard n-GaSb/n-GaInAsSb/P-AlGaAsSb LED operating in the same spectral range. The approach suggested will make it possible to improve LED parameters in the entire mid-IR spectral range (2–5 μm).     

3<Emphasis Type="Italic">C</Emphasis>-SiC <Emphasis Type="Italic">p-n</Emphasis> structures grown by sublimation on 6<Emphasis Type="Italic">H</Emphasis>-SiC substrates

Sublimation epitaxy in a vacuum has been employed to grow n-and p-type 3C-SiC layers on 6H-SiC substrates. Diodes have been fabricated on the basis of the p-n structure obtained, and their parameters have been studied by measuring their current-voltage and capacitance-voltage characteristics and by applying the DLTS and electroluminescence methods. It is shown that the characteristics of the diodes studied are close to those of diodes based on bulk 3C-SiC. A conclusion is made that sublimation epitaxy can be used to fabricate 3C-SiC p-n structures on substrates of other silicon carbide polytypes.     

Low-Power FPGA-Implementation of <Emphasis Type="Italic">atan</Emphasis>(<Emphasis Type="Italic">Y</Emphasis>/<Emphasis Type="Italic">X</Emphasis>) Using Look-Up Table Methods for Communication Applications

This paper presents an architecture for the computation of the atan(Y/X) operation suitable for broadband communication applications where a throughput of 20 MHz is required. The architecture takes advantage of embedded hard-cores of the FPGA device to achieve lower power consumption with respect to an atan(Y/X) operator based on CORDIC algorithm or conventional LUT-based methods. The proposed architecture can compute the atan(Y/X) with a latency of two clock cycles and its power consumption is 49% lower than a CORDIC or 46% lower than multipartite approach.

Recombination of charge carriers in the GaAs-based <Emphasis Type="Italic">p</Emphasis>-<Emphasis Type="Italic">i</Emphasis>-<Emphasis Type="Italic">n</Emphasis> diode

It is established that the radiative recombination of charge carriers plays a substantial role in the GaAs-based p-i-n diodes at high densities of the forward current. It is shown experimentally that the diodes operating in microwave integrated circuits intensely emit light in the IR range with wavelengths from 890 to 910 nm. The obtained results indicate the necessity of taking into account the features of recombination processes in the GaAs-based microwave p-i-n diodes.     

Light-Harvesting in <Emphasis Type="Italic">n</Emphasis>-ZnO/<Emphasis Type="Italic">p</Emphasis>-Silicon Heterojunctions

Zinc oxide (ZnO) films were deposited onto Si to form n-ZnO/p-Si heterojunctions. Under the illumination of by both ultraviolet (UV) light and sunlight, obvious photovoltaic behavior was observed. It was found that the conversion efficiency of the heterojunctions increased significantly with increasing thickness of the ZnO film, and the mechanism for light-harvesting in the heterojunctions is discussed. The results suggest that ZnO films may be helpful to increasing the harvesting of UV photons, thus decreasing the thermalization loss of UV energy in Si-based solar cells.     

An ultra-low-power CMOS symmetrical OTA for low-frequency <Emphasis Type="Italic">G</Emphasis><Subscript><Emphasis Type="Italic">m</Emphasis></Subscript>-<Emphasis Type="Italic">C</Emphasis> applications

In this paper an ultra-low-power CMOS symmetrical operational transconductance amplifier (OTA) for low-frequency G _m -C applications in weak inversion is presented. Its common mode input range and its linear input range can be made large using DC shifting and bulk-driven differential pair configuration (without using complex approaches). The symmetrical OTA was successfully verified in a standard CMOS 0.35-μm process. The measurements show an open loop gain of 61 dB and a unit gain frequency of 195 Hz with only 800 mV of power supply voltage and just 40 nW of power consumption. The transconductance is 66 nS, which is suitable for low-frequency G _m -C applications.     

Thin-film polycrystalline <Emphasis Type="Italic">n</Emphasis>-ZnO/<Emphasis Type="Italic">p</Emphasis>-CuO heterojunction

Results of X-ray diffraction and spectral-optical studies of n-ZnO and p-CuO films deposited by gas-discharge sputtering with subsequent annealing are presented. It is shown that, despite the difference in the crystal systems, the polycrystallinity of n-ZnO and p-CuO films enables fabrication of a heterojunction from this pair of materials.     

Electrical Breakdown in Pure <Emphasis Type="Italic">n</Emphasis>- and <Emphasis Type="Italic">p</Emphasis>-Si

The results of calculations of the dependences of the kinetic coefficients of impact ionization and thermal recombination on an electric field in pure silicon are presented. By analogy with germanium, the dependences of the breakdown field Е_br on the material compensation ratio K are calculated. The validity of such calculation is justified in detail. The Е_br(K) curves are presented and compared with experimental data in the weak-compensation region. Matching with experimental results at which satisfactory agreement between theory and experiment is observed is performed.     

Electrical properties of <Emphasis Type="Italic">n-</Emphasis>GaN/<Emphasis Type="Italic">p</Emphasis>-SiC heterojunctions

Epitaxial GaN layers were grown by hydride vapor phase epitaxy (HVPE) on commercial (CREE Inc., USA) p⁺-6H-SiC substrates (Na ? Nd ≈ 7.8 × 10¹⁷ cm^s?3) and n⁺-6H-SiC Lely substrates with a predeposited p⁺-6H-SiC layer. A study of the electrical properties of the n-GaN/p-SiC heterostructures obtained confirmed their fairly good quality and demonstrated that the given combination of growth techniques is promising for fabrication of bipolar and FET transistors based on the n-GaN/p-SiC heterojunctions.     

Electrical properties of <Emphasis Type="Italic">n</Emphasis>-ZnO/<Emphasis Type="Italic">p</Emphasis>-CuO heterostructures

The n-ZnO/p-CuO heterostructure is prepared, and its I-V characteristic is measured. It is shown that the heterostructure conductivity is primarily determined by the CuO layer and the n-ZnO/p-CuO heterojunction itself.     

Electrodeposition of <Emphasis Type="Italic">p</Emphasis>-Type Sb<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Te<Subscript><Emphasis Type="Italic">y</Emphasis></Subscript> Thermoelectric Films

Thermoelectric Sb _x Te _y films were potentiostatically electrodeposited in aqueous nitric acid electrolyte solutions containing different concentrations of TeO₂. Stoichiometric Sb _x Te _y films were obtained by applying a voltage of −0.15 V versus saturated calomel electrode (SCE) using a solution consisting of 2.4 mM TeO₂, 0.8 mM Sb₂O₃, 33 mM tartaric acid, and 1 M HNO₃. The nearly stoichiometric Sb₂Te₃ films had a rhombohedral structure, R[`3]m R\bar{3}m , with a preferred orientation along the (015) direction. The films had hole concentration of 5.8 × 10¹⁸/cm³ and exhibited mobility of 54.8 cm²/Vs. A more negative potential resulted in higher Sb content in the deposited Sb _x Te _y films. Furthermore, it was observed that the hole concentration and mobility decreased with increasingly negative deposition potential, and eventually showed insulating properties, possibly due to increased defect formation. The absolute value of the Seebeck coefficient of the as-deposited Sb₂Te₃ thin film at room temperature was 118 μV/K.     

A DLTS study of 4<Emphasis Type="Italic">H</Emphasis>-SiC-based <Emphasis Type="Italic">p</Emphasis>-<Emphasis Type="Italic">n</Emphasis> junctions fabricated by boron implantation

Deep-level transient spectroscopy (DLTS) has been used to study p-n junctions fabricated by implantation of boron into epitaxial 4H-SiC films with n-type conductivity and the donor concentration (8–9) × 10¹⁴ cm⁻³. A DLTS signal anomalous in sign is observed; this signal is related to recharging of deep compensating boron-involved centers in the n-type region near the metallurgical boundary of the p-n junction.     

High-temperature nuclear-detector arrays based on 4 <Emphasis Type="Italic">H</Emphasis>-SiC ion-implantation-doped <Emphasis Type="Italic">p</Emphasis><Superscript>+</Superscript>-<Emphasis Type="Italic">n</Emphasis> junctions

Results obtained in a study of spectrometric characteristics of arrays of four detectors based on 4H-SiC ion-implantation-doped p ⁺-n junctions in the temperature range 25–140 °C are reported for the first time. The junctions were fabricated by ion implantation of aluminum into epitaxial 4H-SiC layers of thickness ≤45 μm, grown by chemical vapor deposition with uncompensated donor concentration N _d ? N _a = (4–6) × 10¹⁴ cm^?3. The structural features of the ion-implantation-doped p ⁺-layers were studied by secondary-ion mass spectrometry, transmission electron microscopy, and Rutherford backscattering spectroscopy in the channeling mode. Parameters of the diode arrays were determined by testing in air with natural-decay alpha particles with an energy of 3.76 MeV. The previously obtained data for similar single detectors were experimentally confirmed: the basic characteristics of the detector arrays, the charge collection efficiency and energy resolution, are improved as the working temperature increases.     

Implementation of a field programmable gate array for wireless control of a <Emphasis Type="Italic">lab</Emphasis>-<Emphasis Type="Italic">on</Emphasis>-<Emphasis Type="Italic">a</Emphasis>-<Emphasis Type="Italic">robot</Emphasis>

We report the design of a digital system to wirelessly control microchip capillary electrophoresis (CE) equipment and a mobile unit for chemical analysis. The digital system consists of an embedded processor designed for digital control, decoding and applying of wirelessly-transmitted test parameters, data acquisition, and mobility control. The design is implemented on a field programmable gate array (FPGA) and its development board interfaces with four digital-to-analog converters on a newly-designed 3-channel high voltage power supply, electrochemical detector, wireless modems for communications with a base unit, mobile platform motor controllers, GPS sensor, and an air micropump. The FPGA allows for all the interfacing hardware to perform CE and transmission of the data acquired from the interfacing electrochemical detector. The work described herein extends the utilization of microchip capillary electrophoresis to include remotely controlled field applications.     

Role of spontaneous polarization in the formation of <Emphasis Type="Italic">NH</Emphasis>-SiC/3<Emphasis Type="Italic">C</Emphasis>-SiC/<Emphasis Type="Italic">NH</Emphasis>-SiC structures based on silicon carbide polytypes

The effect of the electrostatic field caused by spontaneous polarization in hexagonal plates of a heterostructure based on NH-SiC/3C-SiC/NH-SiC silicon carbide polytypes on relative positions of energy bands is considered. It was shown that the asymmetry arising in the system is associated with the superposition of polarization and contact fields.     

Differential capacitance of a <Emphasis Type="Italic">p</Emphasis><Superscript>+</Superscript>-<Emphasis Type="Italic">p</Emphasis> junction

The differential capacitance of a p ⁺-p junction formed by charge redistribution near the junction, has been investigated taking into account the electric field in the quasi-neutral p region. The dependence of the capacitance and current of the p ⁺-p junction on its voltage is obtained. It is shown that a change in the sign of the p ⁺-p-junction capacitance with an increase in the injection level is caused by a decrease in the bipolar drift mobility in the p-type region. It is also demonstrated that a change in the sign of the p ⁺-p-junction capacitance with an increase in the reverse voltage determines the charge reduction near the junction, as the increase in the negative charge of acceptor ions predominates over the increase in the positive charge of holes.     

Comparison of <Emphasis Type="Italic">p</Emphasis>-cycles and <Emphasis Type="Italic">p</Emphasis>-trees in a unified mathematical framework

As high-speed networks grow in capacity, network protection becomes increasingly important. Recently, following interest in p-cycle protection, the related concept of p-trees has also been studied. In one line of work, a so-called “hierarchical tree” approach is studied and compared to p-cycles on some points. Some of the qualitative conclusions drawn, however, apply only to p-cycle designs consisting of a single Hamiltonian p-cycle. There are other confounding factors in the comparison between the two, such as the fact that, while the tree-based approach is not 100% restorable, p-cycles are. The tree and p-cycle networks are also designed by highly dissimilar methods. In addition, the claims regarding hierarchical trees seem to contradict earlier work, which found pre-planned trees to be significantly less capacity-efficient than p-cycles. These contradictory findings need to be resolved; a correct understanding of how these two architectures rank in terms of capacity efficiency is a basic issue of network science in this field. We therefore revisit the question in a definitive and novel way in which a unified optimal design framework compares minimum capacity, 100% restorable p-tree and p-cycle network designs. Results confirm the significantly higher capacity efficiency of p-cycles. Supporting discussion provides intuitive appreciation of why this is so, and the unified design framework contributes a further theoretical appreciation of how pre-planned trees and pre-connected cycles are related. In a novel further experiment we use the common optimal design model to study p-cycle/p-tree hybrid designs. This experiment answers the question “To what extent can a selection of trees compliment a cycle-based design, or vice-versa?” The results demonstrate the intrinsic merit of cycles over trees for pre-planned protection.     

Spectral photosensitivity of <Emphasis Type="Italic">a</Emphasis>-SiGe:H/<Emphasis Type="Italic">c</Emphasis>-Si heterostructures

Characteristics of a-SiGe:H/c-Si heterostructures produced by rapid plasma-chemical low-frequency (55 kHz) deposition are studied. High photosensitivity of a-SiGe:H films is established. The spectral position of the maximum of photosensitivity of a a-SiGe:H/c-Si heterostructure can be varied from 830 to 920 nm by increasing the content of germanium in an a-SiGe:H alloy and decreasing its band gap.