混响室\

在功率平衡法的网络化公式应用中, 精确预知腔内装载物的耦合截面积是关键, 这通常依赖于混响室的实验测定.文中使用平面波角谱概念和蒙特卡罗方法来数值模拟混响室中的电磁环境, 在此基础上, 首次应用基于互易定理的快速全波分析方法提取了理想混响室内靠近理想导电地平面的多导体传输线的平均耦合截面积, 验证了方法的正确性, 并计算了单根裸线传输线、带包层传输线、双绞传输线、传输线附近有导体挡板以及多导体传输线端口的平均耦合截面积.该方法具有计算精度高、仿真速度快、适用范围广的特点.     

多导体传输线高频分布参数分析

多导体传输线高频场线耦合研究是当前电磁兼容研究的重点和难点,而多导体传输线上的耦合响应与线上的高频分布参数紧密相关。由于经典传输线理论中采用准TEM波近似,使其不适用于求解高频分布参数。为此,从基于TLST理论的非均匀多导体传输线高频场耦合模型出发,对多导体传输线高频分布参数进行了研究和分析,计算出多导体传输线上的沿线单位长度高频分布参数,并将其与利用经典传输线理论计算得到的结果进行了比较,对二者的差异进行了分析,最后通过高频场线耦合算例说明了本文高频分布参数计算的正确性。     

多导体传输线的邻近效应和分布参数研究

随着多导体传输线内各导体之间间距的减小, 导体之间的近邻效应对传输线的分布参数和传输特性的影响越来越大.为此, 我们针对三种典型的传输线结构, 分别建立了基于矢势有限元方法分析的多导体传输线的模型, 并分析了近邻效应对磁通密度和分布电感的影响.利用提出的方法计算了同轴传输线的单位长度分布电感, 并将它与采用解析方法得到的结果进行比较来证明该方法的正确性.计算双线传输线在不同间距时的单位长度电感, 与理论分析得到的结果相比较验证了导线间距越小, 近邻效应对单位长度电感的影响越大.最后, 计算考虑了近邻效应的耦合微带线的电感矩阵, 并将它与其他不考虑近邻效应的方法得到的结果相比较, 说明近邻效应对传输线电感矩阵的影响.     

多导体传输线瞬态响应研究

随着多导体传输线内各导体之间间距的减小, 导体之间的近邻效应对传输线的分布参数和传输特性的影响越来越大.为此, 我们针对三种典型的传输线结构, 分别建立了基于矢势有限元方法分析的多导体传输线的模型, 并分析了近邻效应对磁通密度和分布电感的影响.利用提出的方法计算了同轴传输线的单位长度分布电感, 并将它与采用解析方法得到的结果进行比较来证明该方法的正确性.计算双线传输线在不同间距时的单位长度电感, 与理论分析得到的结果相比较验证了导线间距越小, 近邻效应对单位长度电感的影响越大.最后, 计算考虑了近邻效应的耦合微带线的电感矩阵, 并将它与其他不考虑近邻效应的方法得到的结果相比较, 说明近邻效应对传输线电感矩阵的影响.     

一种多导体传输线瞬态响应时间步积分法

针对时域有限差分法分析非均匀有损耗多导体传输线瞬态响应的差分振荡问题,提出一种多导体传输线瞬态响应的时间步积分方法。该方法对不等长非均匀有损多导体传输线建模时,无需对耦合传输线进行解耦,能够较方便地求解耦合状态下的不等长非均匀有损多导体传输线系统。所提方法首先对电波方程中的空间微分算子进行差分离散,然后采用梯形积分法对时间微分算子进行积分,最终得到分析不等长非均匀有损多导体传输线瞬态响应的时间步积分算法。该算法不仅应用于不等长非均匀有损多导体传输线模型进行数值计算和理论分析,并对传输线终端端接线性负载和非线性负载的两种情况进行仿真验证。仿真结果表明该方法是有效的。     

关于“螺旋耦合型慢波结构的研究”一文中导纳的计算

“螺旋耦合型慢波结构的研究”(以下简称为“研究”)一文,利用多导体传输线方法对螺旋耦合型慢波结构进行了理论分析。其中用一个简化公式计算了矩形螺旋线各段导纳与翼片导纳,进而计算了大量的色散和耦合阻抗曲线。大家知道,在多导体传输线分析方法中,导纳的计算对色散和耦合阻抗是十分重要的,尤其是耦合阻抗直接与导纳的大小成反比。通过研究,我们认为该文在计算各段导体的导钠时,假     

MacCormack差分法在非均匀多导体传输线分析中的应用

在将MacCormack差分法引入传输线计算的基础上，给出了无需解耦过程的非均匀多导体传输线时域计算方法。摆脱了电容、电感、电阻、电导矩阵形式的限制。该方法是直接的时-空离散数值方法，具有二阶的计算精度。对电路本身没有任何特殊要求，并且应用过程中不需要复杂的变换，便于程序的编制。数值实验表明，利用该方法编制的通用计算程序，具有比快速傅立叶变换法高得多的效率，可以方便的用于均匀、非均匀耦合多导体传输线的计算。     

不均匀多导体传输线的瞬态分析

针对越来越严重的信号畸变和线间耦合问题,应用时域有限差分法（Finite Difference Time Domain,FDTD）建立了不均匀多导体传输线的仿真模型,并通过MATLAB编程对不均匀多导体传输线两端的电压响应进行了仿真分析.在此基础上,理论说明了各端口瞬态响应的波形特点.结果表明了时域有限差分法用于分析多导体传输系统电磁兼容问题的正确性和有效性,为电磁干扰的预测提供了有价值的参考信息.     

孔缝腔体内传输线负载上最大感应电流的研究

应用多端口网络理论,把孔缝屏蔽腔和腔内传输线一起等效成多天线系统,基于天线的互易定理,提出了快速预测孔缝屏蔽腔内多导体传输线负载上的最大感应电流的方法.由于避免了孔缝屏蔽腔内传输线负载上感应电流的直接全波分析,计算效率显著提高.文中计算了矩形屏蔽机箱上开孔尺寸与形状、机箱大小、传输线在机箱内位置等参数改变下屏蔽机箱内传输线负载上的最大感应电流响应.与直接全波仿真结果比较,验证了方法的有效性.     

三维TEM喇叭天线瞬态辐射的FDTD模拟

本文应用FDTD方法分析放置于无限大理想导体地面上并由同轴线馈电的TEM喇叭天线瞬态辐射问题。对FDTD计算区域中的细导线结构采用网格共形技术进行了特殊处理,同时引入一维传输线模型模拟同轴线馈电以大大减少FDTD的计算空间,并实现了天线与同轴线相互耦合的FDTD方法。数值结果表明本文方法处理瞬态天线辐射问题的有效性。     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.     

Call for Papers

正Wireless Body-area Networks The last decade has witnessed the convergence of three giant worlds:electronics,computer science and telecommunications.The next decade should follow this convergence in most of our activities with the generalization of sensor networks.In particular with the progress in medicine,people live longer and the aging of population will push the development of wireless personal networks     

Call for Papers—Feature Topic,Vol.12,No.7,2015

正Information Centric Networking Information-Centric Networking(ICN) is an emerging direction in Future Internet architecture research,gaining significant tractions among academia and industry.Aiming to replace the conventional host-to-host communication model by a data-centric model,ICN treats data content as the first