首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 15 毫秒
1.
The effect of sliding velocity and load on the friction and wear of Cu-steel pairs was studied. Elasto-hydrodynamic (EHL), mixed (ML) and boundary lubrication (BL) regions were analyzed using the Stribeck curve. The lubrication number of Schipper, Z, was used in the analysis of the Stribeck curve. Steady friction states were observed in the mixed EHL and BL regions, however two types of the ML region are revealed. The first type is the stable ML range. The second one is the range of unstable friction and wear when a decrease of the lubricant film leads to abrupt change of all controlled parameters. It was found that a transition to the unstable ML region occurs within a narrow range of Z parameter. Wear modes in the lubrication regions were studied. Deformation hardening in the lubricant regimes is discussed.  相似文献   

2.
Friction and wear of copper rubbed with lubrication in wide range of loads and sliding velocities were studied. The results of friction and wear experiments are presented as the Stribeck curve where the boundary lubrication (BL), mixed (ML) and elasto-hydrodynamic lubrication (EHL) regions are considered. The structural state of subsurface layers in different lubricant regions is studied by X-ray photoelectron spectroscopy, optical, transmission and scanning microscopy analysis. Dislocation density of dislocations in EHL and BL lubricant regimes was determined. Nanohardness at thin surface layers rubbed under different lubricant regimes is compared. The dominant friction and wear mechanisms in different lubrications regions are discussed.  相似文献   

3.
Recently, friction and wear behaviour of Copper (Cu)–steel pairs rubbed under different lubrication conditions were studied. The Stribeck curve was used to identify the different regimes of friction of copper with different virgin grain sizes: the elasto-hydrodynamic lubrication (EHL), mixed lubrication and boundary lubrication (BL) regimes. The aim of this work is the detailed analysis of the damage evolution under friction in the EHL and mixed EHL regions. The effects of load on the friction and the wear and damage mechanisms have been studied. The surfaces of Cu samples before and after friction have been analysed using SEM and AFM techniques as well as roughness and hardness measurements. It was shown that the mechanisms of damage and failure of Cu samples under friction in the EHL region are similar to the damage and failure mechanisms in Very High Cycle Fatigue. Friction in the EHL region is accompanied by initiation and coalescence of pores and microcracks. The effects of the coalescence of pores and microcracks observed in the EHL region are enlarged with a subsequent loading in the mixed EHL region. The effect of the loading rate on the transition from the EHL to BL region has been studied. It was shown that decreasing the loading rate increases significantly the load of the transition from the EHL to BL region. The pore and microcrack coalescence remain as the dominant damage mechanism under friction in the mixed EHL region with the low loading rate, while a lot of ploughing tracks and large delaminated regions appeared on the surface of Cu sample after friction with the higher loading rate.  相似文献   

4.
In the present work, the effect of grain size on the friction and wear behavior of a copper (Cu) samples under different lubricant conditions was studied. The structural evolution of Cu subsurface layers under friction in different lubricant conditions was considered. All friction tests were conducted under laboratory conditions using a block-on-ring rig. The effects of sliding velocity and load on the friction coefficient and wear rate of Cu with different grain size (1, 30, and 60 μm) were analyzed. The Cu samples with the average grain size of 1 μm were obtained due to severe plastic deformation (SPD) by equal channel angular pressing (ECAP). The Stribeck curves for Cu samples with different virgin grain sizes were considered. Elasto-hydrodynamic lubrication (EHL) and boundary lubrication (BL) regions were mainly studied in the present work. Similar Stribeck curves were found out for Cu samples with different virgin grain size. A load of the transition from the EHL to BL region was increased with a decrease of the grain size. While the friction coefficients were similar in the EHL and BL regions for the samples with different grain sizes, the wear rate was increased remarkably with an increase the virgin grain size. Flow localization during friction in the BL region led to formation of the vortex structure in subsurface layers. Based on the dependence of the microhardness upon the depth, the degree of hardening (H) was evaluated. A correlation between the coefficient of wear and the deformation hardening of Cu samples with different virgin grain sizes was revealed. In order to take into account the effect of the grain size and to predict the Stribeck curve, a parameter, K, as the ratio between hardness of tested and annealed samples, was incorporated into the lubricant number. The theoretical values of the Stribeck curve calculated for preliminary deformed Cu samples (d = 1 μm) and annealed samples (d = 60 μm) were well coincided with the experimental results.  相似文献   

5.
Friction Reduction in Mixed Lubrication   总被引:1,自引:0,他引:1  
Minimization of frictional losses in the drivetrain of heavy-duty vehicles is important from both consumer satisfaction and environmental perspectives. Approaches to friction reduction in these components can be evaluated using simulation-based investigations. However, nearly all drivetrain components operate in the mixed lubrication regime which is difficult to model because both hydrodynamic lubrication and surface contact are significant and therefore, the total friction consists of hydrodynamic friction due to lubricant shearing and boundary film friction at asperity contact locations. Recent advances in simulation methods for mixed elastohydrodynamic lubrication (EHL) have enabled improved virtual design tools, such as those developed by Zhu and Hu and further improved by Liu et al. Here, these simulation tools are used to evaluate friction reduction and predict the effects on a mixed EHL interface under severe operating conditions. Three practical means of friction reduction are discussed based on the experimentally validated mixed lubrication friction model and its predictions made for representative, sample cases.  相似文献   

6.
界面滑移条件下点接触Stribeck曲线的实验研究   总被引:4,自引:0,他引:4  
采用高黏度聚异丁烯润滑油,在光学弹流实验机上考察球-盘接触纯滑条件下的摩擦因数随卷吸速度和载荷的变化。结果表明,随着卷吸速度的增加,球-盘接触副进入弹流润滑并向流体动压润滑转变的过程中,摩擦因数并不像传统的Stribeck曲线一样,随着卷吸速度的增加而单调增加,而是呈现先上升、后下降、再上升的趋势,其中摩擦因数下降时的起始速度大致为凹陷出现的速度,摩擦因数再上升时的速度大致是润滑进入动压润滑的速度。初步论证界面滑移为产生上述波动的主要原因。  相似文献   

7.
硅油润滑对莫来石基陶瓷摩擦磨损性能的影响研究   总被引:1,自引:1,他引:0  
莫来石基陶瓷具有一系列优异的性能,其在摩擦学领域中的应用越来越广泛。本文研究了硅油润滑对该类陶瓷摩擦磨损性能的影响规律。研究结果表明,硅油可明显地降低莫来石基陶瓷的摩擦系数和磨损率,但却使摩擦系数在稳定阶段的波动幅度增加。硅油润滑条件下,莫来石基陶瓷的磨损机理主要是微观断裂和磨料磨损。  相似文献   

8.
Abstract

A one-dimensional elstohydrodynamic mixed lubrication wear and friction model is developed. The model can predict the effects of surface roughness, asperity contact, temperature-pressure-viscosity on wear, lubrication, and friction of the piston rings and cylinder liner. Wear is predicted based on the surface asperity contact pressure. The cylinder bore wear and the ring pack friction during an engine break-in are simulated and compared with the experimental results. The influence of cylinder wall temperature and surface roughness on friction and wear is investigated. The ring pack friction due to oil viscous shearing and asperity contact is found to reach its minimum at a certain oil temperature.  相似文献   

9.
This article is concerned with an investigation of the tribological performance of magnetorheological (MR) fluids in pure sliding soft-elastohydrodynamic lubrication (EHL) steel/polytetrafluoroethylene (PTFE) point contacts. The lubricating properties of MR fluids were measured in thin film, lubricated conditions using a ball-on-three-plates tribometer and compared to base fluids in the form of Stribeck curves. A range of techniques was employed to interpret the possible mechanisms of friction and wear of dispersed iron microparticles. The friction surfaces were investigated using optical microscopy, environmental scanning electron microscopy (ESEM), X-ray photoelectron spectroscopy, and energy-dispersive spectroscopy (EDS). In all cases investigated, the friction coefficient is found to strongly depend on the viscosity of the lubricant oil. In the case of low-viscosity liquids, iron microparticles are entrapped in the contact and plow the PTFE surfaces resulting in a sensibly constant friction coefficient. For intermediate viscosities, friction decreases at low speeds because of the so-called ??ball-bearing?? effect, and later, friction increases as particles become embedded in the PTFE matrix. Finally, for high-viscosity fluids, iron particles either accumulate around the rubbing zone as a barrier that reduces the supply of oil available to the contact for boundary lubrication or the particles indent PTFE surfaces.  相似文献   

10.
High hardness, high elastic modulus, low friction characteristics, high wear and corrosion resistance, chemical inertness, and thermal stability are factors that make diamond-like carbon (DLC) coatings the subject of many studies. For the same reasons they also seem suitable for use in, amongst others, machine components and cutting tools. While most studies in the literature focus on the influence of coatings on wear and friction in boundary lubrication and pure sliding contacts, few studies can be found concerning rolling and sliding elastohydrodynamic lubrication (EHL) friction, especially in the mixed and full film regime. In this article tests are carried out in a Wedeven Associates Machine tribotester where an uncoated ball and disc pair is compared to the case of coated ball against uncoated disc, coated disc against uncoated ball, and coated disc against coated ball. The tests are conducted at two different temperatures and over a broad range of slide-to-roll ratios and entrainment speeds. The results are presented as friction maps as introduced in previous work (Bj?rling et al. in J Eng Tribol 225(7):671, 2011). Furthermore a numerical simulation model is developed to investigate if there is a possibility that the hard, thin DLC coating is affecting the friction coefficient in an EHL contact due to thermal effects caused by the different thermal properties of the coating compared to the substrate. The experimental results show a reduction in friction coefficient in the full film regime when DLC-coated surfaces are used. The biggest reduction is found when both surfaces are coated, followed by the case when either ball or disc is coated. The thermal simulation model shows a substantial increase of the lubricant film temperature compared to uncoated surfaces when both surfaces are coated with DLC. The reduction in friction coefficient when coating either only the ball or the disc are almost the same, lower than when coating both the surfaces but still higher than the uncoated case. The findings above indicate that it is reasonable to conclude that thermal effects are a likely cause for the decrease in coefficient of friction when operating under full film conditions, and in the mixed lubrication regime when DLC-coated surfaces are used.  相似文献   

11.
多孔UHMWPE软骨材料润滑性能的Stribeck研究   总被引:1,自引:0,他引:1  
采用T-L法制备出仿生多孔UHMWPE材料,测试了其与水的接触角;在不同的摩擦学条件下测试了普通UHMWPE和多孔UHMWPE试样与不锈钢接触时的润滑性能,并利用Stribeck润滑曲线分析了其润滑状态。结果表明:多孔结构能提高UHMWPE的亲水性能;水润滑条件下,普通UHMWPE表面只能形成边界润滑区域;仿生多孔UHM-WPE具有的多孔结构使得在高速低条件下能形成混合润滑区域,降低材料的摩擦磨损行为;牛血清润滑下普通UHM-WPE的润滑情况变化不大,多孔UHMWPE试样的Stribeck曲线谷底较宽,说明比水润滑条件下具有更好的润滑性能。  相似文献   

12.
短切玻璃纤维增强尼龙材料的摩擦与磨损   总被引:2,自引:0,他引:2  
在环块式磨损试验机上研究了载荷、速度以及润滑介质等因素对自制短切玻璃纤维增强尼龙材料摩擦学行为的影响 ,利用扫描电镜对其磨损机理进行分析。发现 :材料的摩擦系数随载荷的增加而下降 ,达到最小值后 ,又随载荷的增加而持续上升 ,随着速度的增加 ,材料的摩擦系数增加 ;材料的磨损量则随载荷、速度的增加而持续增加 ;材料的磨损以粘着、疲劳为主。在润滑条件下 ,复合材料的摩擦系数大大降低 ;油润滑条件下 ,材料基本无磨损 ,但水润滑条件下 ,材料的磨损量反而比干摩擦条件下大。  相似文献   

13.
The tribological behavior of 30 vol% carbon fiber–reinforced polyetheretherketone (CFRPEEK) against AISI 431 steel under different temperatures of water lubrication was investigated. Friction and wear tests were carried out on a disc-on-disc contact test apparatus under different operating conditions. The results reveal that the lubricant temperature has a significant effect on the friction and wear properties of CFRPEEK sliding against AISI 431 steel. The average friction coefficient and wear rate of CFRPEEK increase with increasing lubricant temperature. However, the wear rate of AISI 431 steel did not have a positive correlation with the wear rate of CFRPEEK under different temperatures of water lubrication. Moreover, the original and worn surfaces of CFRPEEK and AISI 431 steel were imaged by environmental scanning electron microscopy and optical microscopy, respectively. The main tribological mechanisms of CFRPEEK sliding against AISI 431 steel were adhesive wear, and increasing the temperature of the lubricant could accelerate wear.  相似文献   

14.
Greenberg  R.  Halperin  G.  Etsion  I.  Tenne  R. 《Tribology Letters》2004,17(2):179-186
A study of the tribological behavior of nested inorganic fullerene-like (IF) nanoparticles of WS2, as a potential additive to base oils is presented. Friction measurement results obtained from three different test rigs over a wide range of normal loads and sliding velocities are shown. Stribeck curves are used to reveal the lubrication regimes where the IF are most effective. It is found that the addition of IF-WS2 nanoparticles to the base oils results in up to 50% reduction in friction coefficient in the mixed lubrication regime. The mechanism of improved friction and wear behavior with the IF additive is discussed.  相似文献   

15.
In this research investigation, the lubricated wear behavior of leaded α+β brass sliding against stainless steel counterface was studied with the aid of a pin-on-disk apparatus. The main objective of this work was to study the effect of aqueous based environments on the interface and tribological characteristics of this tribosystem, as in several cases the formation of a thin corrosion product layer can act as a lubricating film, decreasing the coefficient of friction of the tribosystem. Thus distilled water and 3.5% NaCl solutions were used as possible lubricants and were then compared with a commercial SAE 80 W lubricant, which is extensively used in many light and heavy-duty, automotive, commercial or industrial applications. From the experimental results obtained, Stribeck curves for each lubricative environment were exacted and analyzed. In addition, by evaluating changes in the coefficient of friction of the tribosystem in accordance with the observed wear mechanisms, the characteristic lubrication regimes (elastodynamic, mixed and boundary) were identified in these curves.  相似文献   

16.
An experimental study is presented to evaluate the influence of anisotropically shaped textures on the behaviour of sliding friction and sensitivity to sliding direction. The plate samples were textured with triangular sloped dimples using an ultrafast laser surface texturing technique. Reciprocating cylinder-on-plate tests were conducted with steel sliding pairs using mineral base oil as a lubricant to compare the tribological performance of reference non-textured specimen and dimpled samples. The dimples were designed with varying converging angles in the transverse yz plane and top-view xy plane. In this study, no dimple was fully covered in the contact area since the dimples size is much larger than the Hertzian line contact width. Stribeck style dynamic friction curves across boundary, mixed and hydrodynamic lubrication regimes were used to determine the benefit or antagonism of texturing. Observation of the directional friction effect of the anisotropic textures indicated that the converging shapes are beneficial for friction reduction, and the dimpled specimens have a lower friction coefficient particular under prevailing boundary lubrication conditions. It was also found that the real contact length variation rate is a major factor controlling the local friction response. The sloped bottoms of the textures produce effective converging wedge action to generate hydrodynamic pressure and contribute to the overall directional friction effects.  相似文献   

17.
A lubrication/friction model can be implemented in FEM codes to predict the contact area ratio, friction coefficient and strain distribution in lubricated deep drawing process. In the lubrication analysis, the surface roughness effect on lubrication flow is included by using Wilson and Marsault's average Reynolds equation that is appropriated for mixed lubrication with severe asperity contact. With regard to the asperity contact theory, the well-known flattening effect is considered. Friction is expressed in terms of variables such as lubricant film thickness, sheet roughness, lubricant viscosity, interface pressure, sliding speed, and strain rate. The proposed lubrication/friction model combined with a finite element code of deep drawing process to predict the contact area ratio, friction coefficient and strain distribution. Numerical results showed that the present analysis provides a good agreement with the measured strain distributions.  相似文献   

18.
A deterministic numerical model has been developed for simulation of mixed lubrication in point contacts. The nominal contact area between rough surfaces can be divided into two parts: the regions for hydrodynamic lubrication and asperity contacts (boundary lubrication). In the area where the film thickness approaches zero the Reynolds equation can be modified into a reduced form and the normal pressure in the region of asperity contacts can be thus determined. As a result, a deterministic numerical solution for the mixed lubrication can be obtained through a unite system of equations and the same numerical scheme. In thermal analysis, the solution for a moving point heat source has been integrated numerically to get surface temperature, provided that shear stresses in both regions of hydrodynamic lubrication and asperity contacts have been predetermined. A rheology model based on the limit shear stress of lubricant is proposed while calculating the shear stress, which gives a smooth transition of friction forces between the hydrodynamic and contact regions. The computations prove the model to be a powerful tool to provide deterministic solutions for mixed lubrication over a wide range of film thickness, from full-film to the lubrication with very low lambda ratio, even down to the region where the asperity contact dominates.  相似文献   

19.
A ball-on-flat reciprocating micro-tribometer has been used to measure the friction coefficient between aluminium alloy strip and a steel ball. A relatively small ball and correspondingly low contact load is used to give a contact width of the order of 100 m, closer to asperity contact widths than generally found for this type of test. The effects of load, initial strip surface roughness, lubricants and boundary additives are investigated. It is found that the friction coefficient is significantly reduced by the addition of a lubricant. Observations of the wear tracks and ball surface show that the material transfer from aluminium to the ball is reduced in the presence of the lubricant. The initial friction coefficient is further reduced by the addition of a boundary additive, but the friction coefficient after 8 cycles is unchanged.  相似文献   

20.
The application of surface coatings has been shown to reduce friction in elastohydrodynamic lubrication (EHL), not only in the mixed and boundary regime when asperity interactions occur, but also in the full film regime. Several studies suggest that the full film friction reduction is due to a violation of the no-slip boundary condition and thus slip is taking place between the solid and the liquid. Another hypothesis proposes that the full film friction reduction is due to the low thermal conductivity of diamond-like carbon (DLC) coatings. In this work, two DLC coatings with the same composition, but different thicknesses, are investigated with uncoated steel specimens as a reference, all with the same surface roughness. Friction tests in a ball-on-disk machine show that both coatings reduce friction compared to the uncoated reference case in full film EHL. The thicker coating is significantly more effective at reducing friction than the thinner one at a maximum friction reduction of 41 % compared to 29 % for the thinner coating. Moreover, contact angle measurements, surface energy measurements, and spreading parameter calculations show no statistically significant differences between the two coatings, suggesting that the friction reduction capabilities of coatings in full film EHL cannot be described by solid–liquid interactions alone. The difference in friction reduction between the specimens in this work is mainly attributed to different thermal properties.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号