共查询到20条相似文献,搜索用时 609 毫秒
1.
多流中间包导流孔对钢液流动轨迹的影响 总被引:1,自引:0,他引:1
通过采用水模拟试验对多流中间包不同控流形式进行全因素试验,研究并探讨了导流孔不同流向和不同孔径对钢液流动轨迹和多流间差异性的影响;并在工厂对改进前后的导流孔进行对比试验,研究了导流孔对夹杂物行为的影响。研究结果表明:为使钢液能充分利用中间包空间并兼顾钢液向各个出水口流动的均匀性,导流孔应分为主流孔和调节孔。主流孔流向的矢量终点应在内外侧出水口中心垂线的中点,孔径为48~52 mm;调整孔流向的矢量终点应在距纵向包壁前顶点175~220 mm,导流孔面积应在中间包浇注末期仍能保证通钢量的需求。导流孔经改进后钢液在中间包内的停留时间平均增加25%,铸坯中大夹杂物含量减少64.2%;活塞流体积平均增加50%,两流间差异性减小60%,中间包内[wT[O]]降低16.4%。 相似文献
2.
3.
本文结合某水库实例,研究水库导流泄洪洞的设计与施工,对其体的施工设计及施工方法进行详细描述,并对质童控制的要点进行了总结. 相似文献
4.
根据福生水电站冲沙闸佛氏数低消能效果差的特点,采用物理横型试验方法对冲沙闸的泄流能力、水面线、流态、消能效果及对下游河道冲刷影响进行了试验研究,提出了优化后的消耗建筑物型式和结构尺寸,为设计提供了依据. 相似文献
5.
针对某船用锅炉使用重油期间导流罩烧蚀变形,通过拆检分析确认故障点,后续采用新材料重新设计导流罩,更换后运转正常,各项参数符合技术要求。 相似文献
6.
为了提高6流方坯中间包冶金效果,通过中间包水力学模拟试验,研究了导流挡板中导流孔参数对中间包流场特征的影响,并对其进行极差分析,最终确定了导流挡板各参数影响中间包流场特征的主次顺序为:导流孔孔径>倾角>高度.并以此为指导思想,结合CFD数值仿真对导流挡板进行设计.设计方案为:3个导流孔直径分别为93、72、36 mm,位置分别为(220mm,140m m)、(350mm,280m m)、(700 mm,300mm),倾斜角度分别为(21°,15°)、(8°,23°)、(10°,28°).工业试验表明,设置该导流挡板装置可以有效改善钢液流动特性,提高中间包冶金效果. 相似文献
7.
简要介绍了铝及铝型材导流模CAD的开发与应用研究。该系统在中国有色金属总公司“七五”科技攻关项目导流模设计技术研究的基础上,以AutoCAD12.0为平台,应用其开发工具制定而成。采用交互式设计,能够完成从型材图形输入到模具设计图形输出的全过程。整个系统分为若干个模块,各模块间采用磁盘数据文件通讯。 相似文献
8.
以TiAl合金块为原料,利用水冷铜坩埚真空感应熔炼气雾化技术制粉,通过对导流系统和雾化器的优化改进,制备出氧含量低、细粉收率高的球形TiAl合金粉末。结果表明,将导热性好的石墨导流基座和耐冲刷的BN材质陶瓷导流内芯配合使用,既可以保证导流管加热,也可以有效阻止金属熔液的冲刷;螺旋喷管雾化器使雾化点下移,回流区位置远离导流管出口,解决了液柱反流的问题。螺旋分布管能够有效约束雾化气体,动能损失小,能够显著提高细粉收率达20%以上。实验制备的球形TiAl合金粉末流动性为27.7 [s·(50 g)?1],球形度>90%,粉末氧增量小,适用于3D打印和注射成型工艺用粉。 相似文献
9.
10.
11.
自备工业水厂总设计规模3.8×104m3/d,分两期建设,一期规模1.9×104m3/d。净水工艺流程采用折板絮凝池—斜管沉淀池—V型滤池的常规处理工艺。简要介绍了工程主要建、构筑物工艺设计参数、设备配置情况等,并对工艺设计特点及水厂的运行情况进行总结。 相似文献
12.
秦新民 《有色冶金设计与研究》2011,32(3):36-38
信丰县第二水厂水库引水工程设计通过方案比选确定的钢竖管配长杆蝶阀重力流分层取水形式,为一种全新概念取水形式,该取水形式与传统形式相比具有结构简单、造价低、后期生产运行管理方便、维护量小等优点。 相似文献
13.
工程项目的建设周期长,生产要素价格变化频繁,使得工程造价复杂可变。对工程造价的控制与管理贯穿于工程建设的全过程:包括立项决策阶段、设计阶段、工程招标及承发包工程阶段、施工阶段、竣工验收阶段、结算价段和财务决算价段,其中后五个价段均与施工合同有关,所以要做好工程造价控制工作,就必须加强施工合同的管理。 相似文献
14.
15.
介绍了我国城市水污染的现状及其危害情况。提出了城市污水处理发展和建设面临的各种问题。如资金投入问题、标准制定问题、排水管网与污水处理厂的关系等。论述了城市排水管网建设与发展应遵循的原则。遵循分期建设以近为主、远近期相结合的原则,使污染得到控制。 相似文献
16.
Complex construction projects are vulnerable to tipping points. Tipping points are conditions that, when crossed, cause system behaviors to radically change performance. Previous research identified tipping point dynamics as capable of explaining the failure of some nuclear power plant construction projects. These dynamics can also threaten the success of other large, complex construction projects. The current work uses a dynamic project model to test policies for managing tipping point dynamics. The Limerick Unit 2 nuclear power plant project is used to test model usefulness. Sensitivity analysis reveals the rework fraction, strength of subsystem interdependence, and sensitivity of the project to schedule pressure as potential high-leverage points for policy design. The model is used to test policies for managing tipping points that were used to complete the Limerick Unit 2 nuclear power plant after a tipping point threatened project completion. Implications for construction project design and management and research opportunities are discussed. 相似文献
17.
18.
Case Study: Dam Safety during Construction, Lessons of the Overtopping Diversion Works at Aguamilpa Dam 总被引:1,自引:0,他引:1
H. Marengo 《Canadian Metallurgical Quarterly》2006,132(11):1121-1127
A study on risk analysis by overtopping of the diversion works of Aguamilpa Dam in Mexico was carried out to examine the overtopping event of January, 1992. Specifically, this study focuses on the upstream water surface elevation during the flood considering the tunnel discharge actual width and roughness. During this maximum flow event, the upstream cofferdam was overtopped and the discharge tunnels exceeded their maximum hydraulic capacity. The risk analysis was made considering the original hydrologic data (until 1992), the final constructed conditions, to establish a performance function that compares the risk of original deterministic analysis with a probabilistic analysis made in 1992. The study also focuses on practical improvements in the construction stage of tunnels; like lining the floor with hydraulic concrete and shotcrete in vaults and walls, that improves the safety of dams during construction and increases the real return period. The work here is presented as a case study because of the unique large-scale flow conditions that are registered in diversion works of dams. 相似文献
19.
20.
高温熔炉产生烟尘的组成、污染物的组成特点,烟尘设计治理的原理,工艺治理的流程、集烟罩的作用、导流屏的辅助性、治理的主要技术参数,采用活动门提高集烟效果的新方法,利用气箱高压脉冲袋式除尘器治理后,达到排放标准,改善作业环境,满足环境法律法规的要求。 相似文献