Gas-phase elemental mercury capture by a V2O5/AC catalyst

Gas-phase elemental mercury (Hg⁰) capture by an activated coke (AC) supported V₂O₅ (V₂O₅/AC) catalyst was studied in simulated flue gas and compared with that by the AC. The study on the influences of V₂O₅ loading, temperature, capture time and flue gas components (O₂, SO₂, H₂O and N₂) shows that the Hg⁰ capture capability of V₂O₅/AC is much higher than that of AC. It increases with an increase in V₂O₅ loading and is promoted by O₂, which indicates the important role of V₂O₅ in Hg⁰ oxidation and capture; it is promoted slightly by SO₂ but inhibited by H₂O; it increases with an increase in temperature up to 150 °C when Hg desorption starts. X-ray photoelectron spectroscopy analysis and sequential chemical extraction experiments indicate that the main states of Hg captured on V₂O₅/AC are HgO and HgSO₄. Temperature programmed desorption experiments were also made to understand the stability of the Hg captured.     

Elemental sulfur production through regeneration of a SO2-adsorbed V2O5-CoO/AC in H2

H₂ regeneration of an activated carbon supported vanadium and cobalt oxides (V₂O₅-CoO/AC) catalyst–sorbent used for flue gas SO₂ removal is studied in this paper. Elemental sulfur is produced during the H₂-regeneration when effluent gas of the regeneration is recycled back to the reactor. The regeneration conditions affect the regeneration efficiency and the elemental sulfur yield. The regeneration efficiency is the highest at 330 °C, with SO₂ as the product. The production of elemental sulfur occurs at 350 °C and higher with the highest elemental sulfur yield of 9.8 mg-S/g-Cat. at 380 °C. A lower effluent gas recycle rate is beneficial to elemental sulfur production. Intermittent H₂ feeding strategy can be used to control H₂S concentration in the gas phase and increase the elemental sulfur yield. Two types of reactions occur in the regeneration, reduction of sulfuric acid to SO₂ by AC and reduction of SO₂ to elemental sulfur through Claus reaction. H₂S is an intermediate, which is important for elemental sulfur formation and for conversion of CoO to CoS that catalyzes the Claus reaction. The catalyst–sorbent exhibits good stability in SO₂ removal capacity and in elemental sulfur yield.     

Adsorption and oxidation of NH3 over V2O5/AC surface

V₂O₅/AC has been reported to be active for selective catalytic reduction (SCR) of NO with NH₃ at around 200 °C and resistant to SO₂ deactivation. To elucidate its SCR mechanism, adsorption and oxidation of NH₃ over V₂O₅/AC are studied in this paper using TG, MS and DRIFTS techniques. It is found that the adsorption and oxidation of NH₃ take place mainly at VO bond of V₂O₅. A higher V₂O₅ loading results in more NH₃ adsorption on the catalyst. V₂O₅ contains both Brnsted and Lewis acid sites; NH₄⁺ on Brnsted acid sites is less stable and easier to be oxidized than NH₃ on Lewis acid sites. Gaseous O₂ promotes interaction of NH₃ with AC and oxidation of NH₃ over V₂O₅/AC. NH₃ is oxidized into NH₂ and acylamide structures and then to isocyanate species, which is an intermediate for N₂ formation.     

Selective oxidation of methanol to dimethoxymethane over acid-modified V2O5/TiO2 catalysts

Selective oxidation of methanol to dimethoxymethane (DMM) was conducted in a fixed-bed reactor over an acid-modified V₂O₅/TiO₂ catalyst. The influence of the acid modification on its structure, redox and acidic properties, and catalytic performance for methanol oxidation were investigated. The results indicated that the content of vanadia in the catalyst exhibits a vital influence on the dispersion of vanadium species, while the acid modification can enhance its surface acidity. Proper amounts of the acid (W() = 15%) and V₂O₅ (W(V₂O₅) = 15%) components loaded in the acid-modified V₂O₅/TiO₂ catalyst are able to build a bi-functional circumstance that is favorable for the formation of DMM with high activity and selectivity. As a result, for the selective oxidation of methanol, the H₂SO₄-modified V₂O₅/TiO₂ catalyst gives a much higher DMM yield at 150 °C than the unmodified one.     

Electronic Structure of Unsaturated V2O5(001) and (100) Surfaces: Ab Initio Density Functional Theory Studies

Vanadium oxides based materials are well known to play an active role as catalysts in many chemical processes of technological importance like for example hydrocarbon oxidation reactions or selective catalytic reduction of NO _x in the presence of ammonia. Usually the (010) surface is pointed out as the most important, however one has to underline that other low-indices surfaces are by far less studied. In the present study the electronic structure of V₂O₅(001) and (100) surfaces are determined by ab initio DFT methods using gradient-corrected RPBE exchange-correlation functional. As models of surface sections different embedded V₁₄O₄₅H₂₀, V₁₄O₄₄H₁₈, and V₂₁O₆₅H₂₅ clusters are considered for the (001) surface and V₁₂O₄₀H₂₀, V₁₄O₄₆H₂₂, V₁₆O₅₂H₂₄ for the (100) surface. Detailed analyses of the electronic structure of each cluster are performed using charge density distributions, Mayer bond orders, electrostatic potential maps, character of frontier orbitals, and density of states (total as well as partial, atom projected). Results of the calculations show that overall negative charge of the surface oxygen sites scales with their coordination independent of the surface orientation. Terminal oxygen O(1) is charged the least negatively while doubly coordinated atoms –O(2) and O^e(2) have charge twice as large. This indicates that bridging (for (001) and (100) netplanes) and edging (only for (001) netplane) oxygen sites are more nucleophilic than terminal vanadyl sites, which becomes important in view of the reactivity of the different sites for surface chemical reactions. Vanadium atoms present at these surfaces are positively charged (electrophilic) and may play a role of electron acceptors. The unsaturated surfaces show a strong tendency to surface relaxation that manifest by large relaxation energies.     

Corrosion mechanisms of Al2O3/MgAl2O4 by V2O5, NiO, Fe2O3 and vanadium slag

The effects of V₂O₅, NiO, Fe₂O₃ and vanadium slag on the corrosion of Al₂O₃ and MgAl₂O₄ have been investigated. The specimens of Al₂O₃ and MgAl₂O₄ with the respective oxides above mentioned were heated at 10 °C/min from room temperature up to three different temperatures: 1400, 1450 and 1500 °C. The corrosion mechanisms of each system were followed by XRD and SEM analyses. The results obtained showed that Al₂O₃ was less affected by the studied oxides than MgAl₂O₄. Alumina was only attacked by NiO forming NiAl₂O₄ spinel, while the MgAl₂O₄ spinel was attacked by V₂O₅ forming MgV₂O₆. It was also observed that Fe₂O₃ and Mg, Ni, V and Fe present in the vanadium slag diffused into Al₂O₃. On the other hand, the Fe₂O₃ and Ca, S, Si, Na, Mg, V and Fe diffused into the MgAl₂O₄ structure. Finally, the results obtained were compared with those predicted by the FactSage software.     

XANES study of polyaniline-V2O5 and sulfonated polyaniline-V2O5 nanocomposites

In this work, two materials for secondary lithium battery cathodes formed by polyaniline-V₂O₅ and sulfonated polyaniline-V₂O₅, which have a higher charge capacity than the V₂O₅ xerogel, were synthesized. X-ray absorption and Fourier transform infrared spectroscopies were employed to analyze the short-range interactions in these materials. Based on these experiments, it was possible to observe significant differences in the symmetry of the VO₅ units, and this was attributed to the intimate contact between V₂O₅ and the polymers, and to some flexibility of the VO₅ square pyramids due to the low range order of the nanocomposites.     

Preparation and characterization of V2O3 micro-crystals via a one-step hydrothermal process

Phase pure V₂O₃ micro-crystals with a hexagonal dipyramid morphology were fabricated for the first time via a facile one-step hydrothermal method. The crystals were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and differential scanning calorimetry (DSC). A hexagonal dipyramid structure of V₂O₃ enclosed by well-grown {012} facets was obtained by hydrothermally reducing VO(acac)₂ precursor with N₂H₄·H₂O at 220 °C for 48 h. The results indicated that V₂O₃ can be well crystallized up to micron size with distinguished facets by only one step hydrothermal treatment. The formation mechanism and morphology evolution for V₂O₃ micro-crystals were discussed. Based on our experiments, the V₂O₃ nuclei formed and grew by a phase transformation through a dissolution–recrystallization process of VOOH, and the formation of the hexagonal dipyramids was ascribed to the specific adsorption of Hacac to the {012} facets restraining the growth in the directions normal to the {012} facets. The present work provides a facile method for preparing phase pure V₂O₃ micro-crystals with hexagonal dipyramid morphology, which can be used as a new powder material for ceramic fabrication.     

Modeling of SO2 removal in fabric filter

Fabric filters are involved in most semi-dry flue gas desulfurization process and represent ability of SO₂ removal. SO₂ removal efficiency in fabric filter after a semi-dry scrubber is investigated. Experimental results showed that SO₂ inlet concentration has little effect on SO₂ removal efficiency, SO₂ removal efficiency increases as flue gas inlet temperature increases and relative humidity affects SO₂ removal efficiency significantly. The kinetic model based on shrinking core theory has been presented. It is found that, in the beginning, when calcium hydroxide conversion ratio is less than 0.3, SO₂ removal process is mainly controlled by chemical reaction (Model-2); and when calcium hydroxide conversion ratio is greater than 0.3, SO₂ diffusion through product layer is rate limiting (Model-3). The experimental results in fabric filter are successfully correlated by Model-3.     

Enhancement of the visible light photocatalytic performance of C-doped TiO2 by loading with V2O5

V₂O₅ was loaded on the surface of C-doped TiO₂ (C-TiO₂) by incipient wetness impregnation in order to enhance the visible light photocatalytic performance. The physicochemical properties of the C-TiO₂/V₂O₅ composite were characterized by XRD, Raman, TEM, XPS, UV–vis diffuse reflectance spectra, and PL in detail. The result indicated that a heterojunction between C-TiO₂ and V₂O₅ was formed and the separation of excited electron–hole pairs on C-TiO₂/V₂O₅ is greatly promoted. Thus, this composite photocatalyst exhibited enhanced visible light photocatalytic activity in degradation of gas-phase toluene compared with the pristine C-TiO₂.     

Effect of ceria on the structure and catalytic activity of V2O5/TiO2–ZrO2 for oxidehydrogenation of ethylbenzene to styrene utilizing CO2 as soft oxidant

The present study was undertaken to investigate the influence of ceria on the physicochemical and catalytic properties of V₂O₅/TiO₂–ZrO₂ for oxidative dehydrogenation of ethylbenzene to styrene utilizing CO₂ as a soft oxidant. Monolayer equivalents of ceria, vanadia and ceria–vanadia combination over TiO₂–ZrO₂ (TZ) support were impregnated by a coprecipitation and wet impregnation methods. Synthesized catalysts were characterized by using X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy, temperature programmed reduction, transmission electron microscopy and BET surface area methods. The XRD profiles of 550 °C calcined samples revealed amorphous nature of the materials. Upon increasing calcination temperature to 750 °C, in addition to ZrTiO₄ peaks, few other lines due to ZrV₂O₇ and CeVO₄ were observed. The XPS V 2p results revealed the existence of V⁴⁺ and V⁵⁺ species at 550 and 750 °C calcinations temperatures, respectively. TEM analysis suggested the presence of nanosized (<7 nm) particles with narrow range distribution. Raman measurements confirmed the formation ZrTiO₄ under high temperature treatments. TPR measurements suggested a facile reduction of CeO₂–V₂O₅/TZ sample. Among various samples evaluated, the CeO₂–V₂O₅/TZ sample exhibited highest conversion and nearly 100% product selectivity. In particular, the addition of ceria to V₂O₅/TZ suppressed the coke deposition and allowed a stable and high catalytic activity.     

SO2 oxidation over the V2O5/TiO2 SCR catalyst

The effects of V₂O₅ loading of the V₂O₅/TiO₂ SCR catalyst on SO₂ oxidation activity were examined by infrared spectroscopy (DRIFT) and SO₂ oxidation measurement. Vanadium oxide added to the catalyst was found to be well dispersed over the TiO₂ carrier until covered with monolayer V₂O₅. The rate of SO₂ oxidation increased almost linearly with V₂O₅ loading below the monolayer capacity and attained saturation with further increase. The hydroxyl groups bonded to vanadium atoms, V–OH, might be altered by SO₂ oxidation. Both V=O and V–OH groups are likely involved in the adsorption and desorption of SO₂ and SO₃.     

TiO2-V2O5纳米纤维光催化氧化烟气中的Hg0

对静电纺丝法制备的TiO₂和TiO₂-V₂O₅纳米纤维进行光催化脱除模拟烟气中Hg⁰的研究。对纳米纤维进行了SEM、TEM、XRD、BET和UV-Vis检测。结果表明TiO₂-V₂O₅纳米纤维为锐钛矿,V₂O₅高度分散在TiO₂中。纤维直径在200 nm左右,由粒径为10 nm左右的微粒组成。掺杂V₂O₅后,纤维的吸光范围扩大,在可见光范围内的吸光度比纯TiO₂时有了很大提高。实验研究了不同光照条件、V₂O₅的掺杂量和循环次数对脱汞的影响,分析了TiO₂-V₂O₅催化脱汞的机理。当V₂O₅的质量含量为3%时,TiO₂-V₂O₅在可见光下的脱汞率可达到66%,比纯TiO₂时的7%有了显著提高;纤维的脱汞性能稳定,多次循环后紫外光和可见光下的脱汞率仍分别保持在80%和65%左右。电子的跃迁和电子、空穴的快速分离是TiO₂-V₂O₅在可见光下脱汞率提高的主要原因。     

Electrochemical properties of microwave irradiated synthesis of poly(3,4-ethylenedioxythiophene)/V2O5 nanocomposites as cathode materials for rechargeable lithium batteries

A series of poly(3,4-ethylenedioxythiophene) (PEDOT)/V₂O₅ nanocomposites are prepared via the redox intercalative polymerization reaction of 3,4-ethylenedioxythiophene (EDOT) monomer and crystalline V₂O₅ within 10 min by using rapid 2.45 GHz microwave irradiation with full power (800 W). The unique properties of the resultant nanocomposites are investigated by various characterization techniques using powder XRD, TGA/DTA and four-point probe conductivity analysis supports the intercalation of polymer nanosheet between V₂O₅ layers leading to enhanced bi-dimensionality. X-ray photoelectron spectroscopy analysis clearly shows the presence of mixed valent V⁴⁺/V⁵⁺ in the V₂O₅ framework after the redox intercalative polymerization which also confirms charge transfer from the polymer to the V₂O₅ framework. The application potential of these composites as cathode materials in rechargeable lithium batteries is also demonstrated by the electrochemical intercalation of lithium into the PEDOT/V₂O₅ nanocomposites, where an enhancement in the discharge capacity (370 mAh/g) is observed compared to that of crystalline V₂O₅.     

Activity and characterization of Rh/Al2O3 and Rh-Na/Al2O3 catalysts for the SCR of NO with CO in the presence of SO2 and HCl

SO₂ and HCl are major pollutants emitted from waste incineration processes. Both pollutants are difficult to remove completely and can enter the catalytic reactor. In this work, the effects of SO₂ and HCl on the performance of Rh/Al₂O₃ and Rh-Na/Al₂O₃ catalysts for NO removal were investigated in simulated waste incineration conditions. The characterizations of the catalysts were analyzed by BET, SEM/EDS, XRD, and ESCA. Experimental results indicated the 1%Rh/Al₂O₃ catalyst was significantly deactivated for NO and CO conversions when SO₂ and HCl coexisted in the flue gas. The addition of between 2 and 10 wt.% Na promoted the activity of the 1%Rh/Al₂O₃ catalyst for NO removal, but decreased the CO oxidation and BET surface area. The catalytic activity for NO removal was inhibited by HCl as a result of the formation of RhCl₃. Adding Na to the Rh/Al₂O₃ catalyst decreased the inhibition of SO₂ because of the formation of Na₂SO₄, which was observed in the XRD and ESCA analyses. SEM mapping/EDS showed that more S was residual on the surface of the Rh-Na/Al₂O₃ catalyst than Cl.     

Low-temperature firing and microwave dielectric properties of 16CaO–9Li2O–12Sm2O3–63TiO2 ceramics with V2O5 addition

The sintering behaviors and microwave dielectric properties of the 16CaO–9Li₂O–12Sm₂O₃–63TiO₂ (abbreviated CLST) ceramics with different amounts of V₂O₅ addition had been investigated in this paper. The sintering temperature of the CLST ceramic had been efficiently decreased by nearly 100 °C. No secondary phase was observed in the CLST ceramics and complete solid solution of the complex perovskite phase was confirmed. The CLST ceramics with small amounts of V₂O₅ addition could be well sintered at 1200 °C for 3 h without much degradation in the microwave dielectric properties. Especially, the 0.75 wt.% V₂O₅-doped ceramics sintered at 1200 °C for 3 h have optimum microwave dielectric properties of Kr = 100.4, Q × f = 5600 GHz, and TCF = 7 ppm/°C. Obviously, V₂O₅ could be a suitable sintering aid that improves densification and microwave dielectric properties of the CLST ceramics.     

Low cost coal-based carbons for combined SO2 and NO removal from exhaust gas

The aim of this paper is to show how a cheap carbonaceous material such as low rank coal-based carbon (or char) can be used in the combined SO₂/NO removal from exhaust gas at the linear gas velocity used in commercial systems (0.12 m s⁻¹). Char is produced from carbonization and optionally activated with steam. This char is used in a first step to abate the SO₂ concentration at the following conditions: 100 °C, space velocity of 3600 h⁻¹, 6% O₂, 10% H₂O, 1000 ppmv SO₂, 1000 ppmv NO and N₂ as remainder. In a second step, when the SO₂ concentration in the flue gas is low, NO is reduced to N₂ and steam at the following experimental conditions: 150 °C, space velocity of 900 h⁻¹, 6% O₂, 10% H₂O, 0-500 ppmv SO₂, 1000 ppmv NO, 1000 ppmv NH₃ and N₂ as remainder.It has been shown that the presence of NO has no effect on SO₂ abatement during the first step of combined SO₂/NO removal system and that low SO₂ inlet concentration has a negligible effect on NO reduction in the second step. Moreover, this char can be thermally regenerated after use for various cycles without loss of activity. On the other hand, this regenerated char shows the highest NO removal activity (compared to parent chars, either carbonized or steam activated) which can be attributed to the activating effect of the sulfuric acid formed during the first step of the combined SO₂/NO removal system.     

Mixed oxides Ca2Fe2O5 and Ca2Co2O5 as anode materials for Li-ion batteries

The electrochemical performance of mixed oxides, Ca₂Fe₂O₅ and Ca₂Co₂O₅ for use in Li-ion batteries was studied with Li as the counter electrode. The compounds were prepared and characterized by X-ray diffraction and SEM. Ca₂Fe₂O₅ showed a reversible capacity of 226 mAh/g at the 14th cycle and retained 183 mAh/g at the end of 50 cycles at 60 mA/g in the voltage window 0.005-2.5 V. A reversible capacity in the range, 365-380 mAh/g, which is stable up to 50 charge-discharge cycles is exhibited by Ca₂Co₂O₅ in the voltage window, 0.005-3.0 V and at 60 mA/g. This corresponds to recycleable moles of Li of 3.9±0.1 (theoretical: 4.0). Significant improvement in the cycling performance and attainable reversible capacity were noted for Ca₂Co₂O₅ on cycling to an upper cut-off voltage of 3.0 V as compared to 2.5 V. Coulombic efficiency for both compounds is >98%. Electrochemical impedance spectroscopy (EIS) data clearly indicate the reversible formation/decomposition of polymeric surface film on the electrode surface of Ca₂Co₂O₅ in the voltage window, 0.005-3.0 V. Cyclic voltammetry results compliment the galvanostatic cycling data.     

Absorption of polarized X-rays by V2O5-based cathodes for lithium batteries: an application

Vanadium pentoxide materials prepared through sol-gel processes (xerogel, aerogel and aerogel-like) act as excellent intercalation hosts for lithium as well as for polyvalent cations. The large lithium insertion capacity of these materials makes them attractive for use as cathodes in high capacity lithium batteries. This paper describes the utility of X-Ray absorption spectroscopy (XAS) for the investigation of gel-based V₂O₅ materials. In particular, X-ray near edge structure (XANES) and polarized EXAFS experiments are highlighted.