Spray chilling of lamb carcasses

Two spray-chilling treatments were developed to improve appearance and reduce weight loss during lamb chilling. Rates of cooling and weight loss and meat quality were compared to conventionally chilled carcasses.

The first treatment was an intermittent spray during the first 3 h of chilling. The second consisted of only two sprays at 2 h and 10 h post mortem. The conventional control was a two-stage process, with air at 10°C and 1 m/s up to 10 h post mortem, followed by air at 0°C and 1 m/s for a further 14 h.

Both treatments significantly reduced weight loss at 24 h post mortem compared to conventional, from 2·20% to 0·86% and 1·20%, respectively. During a further 4 days storage, the savings were maintained, with weight losses being 3·97%, 2·97% and 3·19%, respectively.

There were small (<1 h) but significantly reductions in the cooling times of spray-chilled loins and legs, attributed to sustained evaporative cooling of the continually wetted surfaces.

No effects on texture or drip loss and only slight effects on surface lean and fat colour were found. Variation in texture between animals within treatments was far greater than between treatments and could not be accounted for by variations in cooling rates.     

The influence of high post-mortem temperature and differing ultimate pH on the course of rigor and ageing in pig Longissimus dorsi muscle

This study was performed in order to assess the effect of temperature and differing ultimate pH (pH_u, 24 h post mortem) on the development of rigor mortis in pig Longissimus dorsi muscle. The rigor development (isometric tension and shortening) was measured continuously during the first 24 h post mortem, using an apparatus wherein muscle strips were held at constant temperatures of 12 or 35°C. pH_u was manipulated by adrenaline injections preslaughter.

The rates of pH fall, adenosine triphosphate (ATP) and creatine phosphate (CP) breakdown were markedly increased at 35°C compared to 12°C. For both temperatures, no delay phase was observed with regard to the development of shortening. Rigor resulted in higher maximum isometric tension and shortening and in shorter time needed to reach maximum values at 35°C than at 12°C. The results are discussed in connection with pH, ATP and CP data. The extent of ageing from 2 to 4 days post mortem, estimated through myofibrillar length determinations, was higher for 12°C than for 35°C.

pH_u affected significantly most of the traits under study, but its effect depended in some cases upon the rigor temperature. At 12°C, the traits related to the kinetics of rigor development were significantly affected by pH_u, but this was not the case at 35°C. Maximum isometric tension was significantly related to pH_u at 35°C (r = 0·86, P < 0·001), but such a relationship was not found at 12°C. Myofibrillar lengths were significantly affected by pH_u, but in an opposite manner from one temperature to another. A positive relationship was found at 12°C and a negative one at 35°C.

These results illustrate the importance of the interaction between the extent of pH fall and temperature with regard to post-mortem changes in pig muscle.     

Prediction of fluid losses from pork using subjective and objective paleness

Meat paleness in pork Longissimus dorsi (LD) 1 day post-mortem (p-m) was measured subjectively using Japanese Pork Colour Scores (JPCS) and objectively using a Colormet fibre-optic (FO) meat probe (400–700 nm). Water-holding capacity (WHC), fluid loss during thin-slicing, and drip loss were measured in unfrozen and in frozen and thawed (FT) samples. FT caused a decrease in WHC, and an increase in slicing and drip loss (P < 0·001). FO interactance (i) was correlated (P < 0·01) with unfrozen WHC (R = 0·55), with FT WHC (r = −0·45 at 440 nm), with FT slicing loss (R = 0·81), with unfrozen drip loss (R = 0·66), and with FT drip loss (R = 0·61). Objective measurements proved that the development of pork paleness takes several days p-m and that paleness is increased by FT. Where fluid losses were predictable from paleness, the FO probe was superior to subjective evaluation by JPCS.     

Identification of halothane genotypes by calcium accumulation and their meat quality using live pigs

The three halothane genotypes (NN, Nn, and nm) were identified by measuring the capacity for Ca²⁺ accumulation by sarcoplasmic reticulum in whole muscle homogenate preparations of M. longissimus dorsi with a Ca²⁺ specific electrode at 35°C. Significant differences (P < 0·001) in deterioration (%) of Ca²⁺ accumulation, 12% for NN, 35% for Nn, and 81% for nn pigs, were observed after ageing the whole muscle homogenate preparations for 24 h in ice.

Predictions of meat quality in live pigs (n = 34) based on the values for water-holding capacity, assessed as fluid (g/0·5 g wet wt LD), and pH (fluid) by using small biopsy LD samples (Cheah et al. 1993) were performed on all the halothane genotypes. The halothane genotype NN (n = 11) showed a fluid value of 0·37 ± 0·01 and a pH (fluid) value of 6·62 ± 0·03 as compared with 0·61 ± 0·02 and 5·84 ± 0·04, respectively, for the halothane genotype nn (n = 13). The Nn pigs (n = 10) showed fluid (0·49 ± 0·03) and pH (fluid) (6·19 ± 0·11) values between those values observed for the two homozygotes (NN and nn). Predictions of meat quality in live pigs from biopsy LD muscles were confirmed from assessments on post-mortem LD muscles based on pH₁ and fibre optic probe (FOP) measurements.

The extent of deterioration (%) in Ca²⁺ accumulation showed high correlations with fluid (r = −0·861) and pH (fluid) (r = −0·831) in the biopsy LD samples, and with pH₁ (r = 0·663), FOP (r = −0·812), and drip (%) loss (r = −0·777) in the post-mortem LD samples.     

The colour of the adductor muscle as a predictor of pork quality in the loin

The relation between measurements of colour made in the m. adductor (AD) at 45 min or 20 h post mortem and the quality, assessed subjectively in terms of colour and waterholding capacity, of the m. longissimus (LD) in the loin was examined. The study used data from 100 pig carcasses exhibiting a wide range of meat quality from extreme PSE (pale, soft and exudative) to extreme DFD (dark, firm and dry). The subjective assessments were confirmed by objective measures of paleness (reflectance) and waterholding capacity (drip loss in storage) in the LD. Lightness (L^*) measured at 20 h post mortem in the AD was the best potential predictor of loin muscle quality, explaining 59% of the variation in subjective and objective quality measures. Comparable measurements at 45 min post mortem explained between 21% and 44% of the variation. The equation that described the relation between AD Lightness (L^*) and subjectively assessed LD quality was derived. This could be used to transpose the AD L^* values from a population of slaughtered pigs into nominal subjective scores for the LD, allowing the frequency of the five subjective quality groups (extremely DFD, slightly DFD, normal, slightly PSE, and extremely PSE) in the population of carcasses to be defined.     

Objective meat quality measurements of ham: A practical classification method on the slaughterline

Meat quality is one of the principal problems in Spanish dry cured ham productuon. At the experimental level, there are well developed objective instrumental measurements which can be made on the slaughterline and then, by applying the correct statistical treatment, these measurements can be used to classify hams with an acceptable degree of accuracy. These treatments, however, are not easy to apply in the industry.

In this work, 312 pork carcasses were tested at three industrial abbatoirs. Ham meat quality was determined by internal light scattering (FOP), electrical conductivity (EC) and pH measurements in Semimembranosus (SM) muscle at 45 min and 24 h post mortem. The results obtained were: 21 (6.7%) DFD; 168 (53.9%) slightly DFD; 104 (33.3%) normal; 11 (3.5%) slightly PSE; and 8 (2.6%) PSE.

A simplified method has been developed for classifying hams into quality categories, by deriving a theoretical quality value (Q) based on a simple statistical treatment of values for FOP, EC and pH. The multiple linear regression coefficient of Q was R² = 0.85 (P<0.001) with respect to the experimental variables.     

Non-destructive prediction of selected quality attributes of beef by near-infrared reflectance spectroscopy between 750 and 1098 nm

Heifers (n = 70) were slaughtered and hung conventionally in an industrial meat plant. Near infrared (NIR) spectroscopy was studied for its ability to predict selected meat quality attributes, i.e. Warner-Bratzler shear force (WBSF), sensory tenderness, texture, flavour and acceptability. Freshly cut steaks (2.5 cm thick) were taken from the longissimus dorsi (LD) muscle at 1, 2, 7 and 14 days post mortem for NIR analysis. Other samples (also 2.5 cm thick) were taken at 2, 7 and 14 days post mortem, vacuum-packaged in plastic bags and stored at −20 °C for WBSF measurement and sensory analysis. Heifers were slaughtered in two groups; between slaughterings, replacement of the spectrophotometer lamp and lamp assembly was necessitated by a bulb failure. Using principal component regression (PCR), correlation coefficients of 0.82 and 0.73 were obtained for the prediction of WBSF in sample sets 1 and 2, respectively. On merging both sample sets, this value was lowered slightly (r = 0.61). Correlation coefficients obtained for the prediction of tenderness, texture, flavour and acceptability were 0.67, 0.53, 0.51 and 0.46 respectively (set 1); 0.72, 0.71, 0.45 and 0.67 (set 2); 0.53, 0.54, 0.24 and 0.42 (combined sets).     

Objective assessment of pork quality

Several objective methods for estimating pork quality were studied: internal light scattering (FOP), electrical conductivity (EC), pH, colour, water holding capacity (WHC), soluble proteins (SP), pigment content, intramuscular fat (i.m. fat), and moisture. The measurements were made on the Semimembranosus and Longissimus thoracis at 45 min and 24 h post mortem in some cases and on the Semimembranosus in others.

Most of the measurements are significantly different between normal, PSE and DFD quality categories.

There is a good correlation between pH values in both muscles: pH₄₅SM-pH₄₅LT (r=0.74) and pH₂₄SM-pH₂₄LT (r=0.71). At 45 min the correlation of EC with FOP and pH was r=0.56 and r=0.48 respectively. Lower correlations were found in other parameters.

The results from principal component analysis (PCA) showed that the three first components explained 60.3% of the total variation and the most important variables for the first PC were pH₄₅ and EC₄₅.     

Comparison between two statistical models for prediction of turkey breast meat colour

The aims of the present study were: (1) to determine the relevant objective measurements which could express visual assessment of turkey meat colour; and (2) to use these variables for the early prediction of the colour development of turkey breast meat.

The colour of the meat was assessed subjectively by an expert at a processing plant at 24 hr post mortem, using a four-category scale (score a: light-pale meat, score b: light pink meat or normal meat, score c: dark meat, score d: very dark meat).

Objective measurements included meat pH, temperature, dielectric loss factor, pigment concentration, L^* (lightness), a^* (redness) and b^* (yellowness) colour coordinates determined at different times post mortem.

Colour coordinates and pH were chosen as relevant variables when measured at 1 and 4 hr post mortem and were used in prediction models. Linear analysis (canonical discriminant analysis) showed that the efficiency of prediction was 15%. A non-linear analysis (neural network) gave better prediction; the colour of the meat being correctly predicted for 70% of the muscles.     

Drip loss of case-ready meat and of premium cuts and their associations with earlier measured sample drip loss, meat quality and carcass traits in pigs

Drip loss of 374 samples taken from porcine M. longissimus dorsi and M. semimembranosus was measured by using the “bag method” (BM), EZ-DripLoss (EZ-DL) from premium cuts (PC) and in retail tray (case-ready meat; CRM). This provided a comparison between these methods and their relationships to other meat quality and carcass traits. Samples were prepared at 24 h post-mortem (pm) and were measured 24 and 48 h after preparation (at 48 and 72 h pm) using the BM and after 48 h (at 72 h pm) with the EZ-DL and PC. Drip loss of meat kept in retail trays was measured after 7 days (CRM₇) and daily within a week (CRM_1–7). Average drip loss was 1.80% and 3.10% using the BM after 24 and 48 h, respectively. EZ-DL and CRM₇ showed higher drip losses of 4.71% and 4.00%. Daily loss of CRM_1–7 showed a concavely shaped curve and increased from 1.57% to 5.64% after 7 days. High correlations were obtained between drip loss of CRM₇ and BM (r = 0.88) or the EZ-DL (r = 0.91). The development of drip loss in case-ready meat fitted by linear-quadratic regression (y = 0.439 + 1.245x − 0.072x²) showed that high drip loss measured earlier by bag and EZ-DripLoss methods was highly associated with a high intercept (r = 0.63–0.72), a high linear increase (r = 0.77–0.81), but larger decrease in increments (r = −0.82 to −0.86) during weekly stored meat in retail trays as supplied at consumer level. Because the positive linear regression coefficient was substantially higher than the negative quadratic regression coefficient, the development of drip loss is mainly dependent on the initial drip loss. Therefore, animals with high drip loss within 72 h post-mortem also showed undesirable high drip loss curves over the entire retail period. Relationships between drip loss and other meat quality traits were similar for BM, EZ-DL and CRM₇. Of these the correlation between pH₂₄ and drip loss was highest with r = −0.54, −0.49 and −0.47 for BM, EZ-DL and CRMH₇, respectively. Interestingly, a correlation of r = −0.35 between blood pH value and CRML₇ was obtained. Carcass traits such as loin, ham, shoulder, belly weight or loin eye area showed only marginal correlations to drip loss. In conclusion, EZ-DL was the most appropriate method to predict drip loss of case-ready meat in retail trays and its development during a 7 day storage period.     

The relationship of muscle fibre size to tenderness of beef

Steaks were removed from loins of beef carcasses at 1, 3, 6 or 14 days post mortem for fragmentation index (MFI), Warner-Bratzler Shear Force (SF) and sensory panel tenderness evaluation. Also, after 1 day of storage, samples were removed for histological observations. Greatest improvement in tenderness, SF and MFI occurred within the first 6 days of storage. Sensory panel tenderness was correlated (P < 0·01) with SF and MFI. Average muscle fibre size was correlated (P < 0·01) with tenderness and SF at days 1 and 3, but not at days 6 and 14. Evidently, muscle fibre size is important to tenderness prior to post-mortem storage of meat and proteolysis, but becomes less of a factor in tenderness after 6 days of storage.     

The effects of spray and blast-chilling on carcass shrinkage and pork muscle quality

Combinations of blast- and spray-chilling of pork carcasses were compared to spray-chilling at conventional chilling temperatures with regard to carcass shrinkage during chilling and pork muscle quality. In experiment 1, pork sides were spray-chilled at 1°C for the first 10 h (40 spray cycles of 60-s duration every 15 min) of cooling or blast-chilled at −20°C for 1, 2 or 3 h followed by spray-chilling for 9, 8 or 7 h duration, respectively. All pork sides were then chilled to 24 h post mortem at 1°C. Experiment 2 followed the same procedures as experiment 1, except that −40°C was used as the blast-chill temperature.

Carcass shrinkage was similar for all treatments in experiment 1 at 24 h ranging from 0·5–0·7 g 100 g⁻¹. Blast/spray-chilling increased the rate of chilling and reduced the rate of post-mortem pH decline in two muscles (longissimus thoracis, LT and semimembranosus, SM) compared to the combined conventional/spray-chill treatment. Carcasses that were blast-chilled for 3 h had LT muscles that were darker with a higher protein solubility, less drip loss, shorter lengths and higher shear values compared to those from carcasses in the conventional/spray-chill treatment. In experiment 2, carcasses blast-chilled for 3 h at −40°C recorded a weight gain at 24 h of 0·4 g 100 g⁻¹, compared to a weight loss in all other treatments (0·2–0·4 g 100 g⁻¹). Muscle colour was darker in both the LT and SM of carcasses blast-chilled for 3 h at −40°C compared to carcasses from the conventional/spray-chill treatment, but most other measurements of muscle quality showed an inconsistent response to chilling treatment.     

Use of the Tecpro Pork Quality Meter for assessing meat quality on the slaughterline

Conductivity measurements made with the Tecpro Pork Quality Meter at either 45 min or about 20 h post mortem on 224 pig cacassees which exhibited a wide range of raw meat quality were moderately correlated with initial pH (pH(45); r = 0.54 and 0.62) but less well correlated with reflectance (r = 0.32 and 0.37), drip loss (r = 0.34 and 0.47 and other objective measures of meat quality in the M. Longissimus dorsi. Measurements did not allow differentiation between normal and dark, firm, dry (DFD) meat but were of some value in identifying carcasses producing potentially pole, soft, exudative (PSE) meat. In the UK they would be more useful for monitoring meat quality in large groups or populations of pigs, than for categorising individual carcasses for grading on technological purposes.     

Impact of salt, phosphate and temperature on the effect of a transglutaminase (F XIIIa) on the texture of restructured meat

The effect of the transglutaminase F XIIIa on texture parameters was analysed in meat model systems simulating a restructured meat product. Porcine M. longissimus dorsi at normal ultimate pH was obtained 2 days post mortem from pigs slaughtered at approx. 100 kg liveweight. The F XIIIa product used was a recombinant protein produced by fermentation of Saccharomyces cereviciae. In raw minced meat F XIIIa increased cohesion, hardness and elasticity when a time-temperature heat treatment of 37 °C and 90 min was used during processing, while processing at 10 °C for 23 h caused only minor texture changes. Salt and phosphate addition together with F XIIIa resulted in a remarkable increase in binding properties. Thus, the texture parameters increased particularly at salt levels between 2 and 4% and a phosphate level of 0.2%. Binding of meat pieces containing 0.2% phosphate, 1% salt and F XIIIa as 0.4% active enzyme to substrate showed significant effect on the tensile strength compared to the samples without F XIIIa, however, color deterioration of the product was observed when adding F XIIIa.     

Colour of normal and high pH beef heated to different temperatures as related to oxygenation

The effects of oxygenation and thermal treatment (internal temperature, T_i: 45, 60, 75°C) on the colour and some colour related physical and biochemical properties of beef longissimus dorsi (LD) muscle, both normal (pH_u5.6) and DFD (pH_u>6.6), were studied. The colour components (L^*, a^*, b^* values) for the raw and heated LD, both before and after oxygenation, were instrumentally and sensorily evaluated. The colour of raw and heated (60°C) DFD beef before and after oxygenation differed significantly from the normal meat and contained more native muscle pigment (TMP). pH also influenced the depth of the oxygenated layer, specific activity of cytochrome c oxidase (SACCO) and the amount of oxygen consumed. An increase in internal temperature was usually accompanied by a lower SACCO and a significant decrease of TMP, as well as a change of all colour parameters. Oxygenation of the raw and heated slices (except at 75°C) of both types of meat led to higher L^*, a^* and b^* values.     

Meat quality characteristics of springbok (Antidorcas marsupialis). 1: Physical meat attributes as influenced by age, gender and production region

Springbok is the most extensively cropped game species in South Africa. The effects of age (adult, sub-adult, lamb), gender and production region on the physical attributes (pH₂₄, cooking and drip loss, Warner Bratzler shear force and colour) were determined using samples of the M. longissimus dorsi (LD) muscles of 166 springbok. Stressed animals had a higher (P < 0.05) pH₂₄ (6.3 ± 0.07), as observed in the meat originating from the Caledon region. This meat had lower (P < 0.05) cooking loss (27.2 ± 0.62%) and drip loss (1.8 ± 0.08%) values in comparison to meat originating from the other regions. Inverse correlations were noted between pH₂₄ and drip loss (r = −0.26, P < 0.01) and cooking loss (r = −0.42, P < 0.001). Shear force values (kg/1.27 cm diameter) correlated positively (r = 0.25, P < 0.01) with pH₂₄. Age-related effects on tenderness were small in comparison with pH₂₄ effects. CIELab colorimetric values were typical of game meat and venison (L^* < 40, high a^* and low b^* values). It was noted that pH₂₄ correlated negatively (r = −0.51, P < 0.001) and positively (r = 0.33, P < 0.001) with the hue-angle and the chroma value of colour, respectively. Springbok originating from Caledon had a significantly (P < 0.05) higher a^* value, indicating meat to be more red with higher colour saturation.     

Variation in post-mortem rate of glycolyis does not necessarily affect drip loss of non-stimulated veal

In this study the effect of the rate of post mortem pH fall on the water-holding capacity of meat from moderately chilled veal carcasses was investigated. Also the relationship between muscle protein denaturation and drip loss of veal was examined. Three groups of 10 Friesian Holstein male veal calves each were selected on the basis of their pH in M. longissimus thoracis et lumborum (LTL) at 3 hr post mortem (pH₃): (1) fast pH-fall, pH₃ < 6.2; (2) intermediate pH-fall, 6.5 < pH₃ < 6.6; (3) slow pH-fall, pH₃ > 6.7. After 48 hr of chilling the LTL was excised from the carcass and sampled for determination of drip loss, filter paper wetness, sarcomere length, protein solubility and transmission value. Differences in pH₃ were not associated with differences in drip loss, filter paper wetness or differences in protein denaturation. It is suggested that at the relatively high veal carcass chilling rate the effect of rate of pH-fall on protein denaturation and thus on drip loss is negligible. Drip loss of veal was highly correlated with both solubility of sarcoplasmic (r = −0.67; p < 0.001) and total muscle protein (r = −0.54; p < 0.01) and with transmission values (r = 0.66; p < 0.001). These results indicate that protein denaturation measurements may be a good predictor for drip loss of veal.     

Enthalpy-Entropy compensation in food vapor adsorption

Enthalpy-entropy compensation was analysed for sorption isotherms of potatoes, macadamia nuts, apricots, figs, currants, prunes and raisins. Plots of (ΔH_dif)_T vs (ΔS_dif)_T for potatoes and macadamia nuts presented two isokinetic temperatures: T_B1 = 272.0 ± 57.7 K (− 1 °C) for potatoes, T_B1 = 265.0 ± 18.8 K (− 8 °C) for macadamia nuts and T_B2 = 382.5 ± 7.3 K (109.5 °C) for both products. The first isokinetic temperature (T_B1) appeared only at the upper portion of the temperature range tested (50, 60 and 70 °C for potatoes and 50 and 60 °C for macadamia nuts). The two isokinetic temperatures observed for potatoes and macadamia nuts suggested that during the initial stages at low a_w T_B1 is controlled by changes in the entropy of water, whereas the second isokinetic temperature (T_B2) is considered to be enthalpy-controlled. Dried fruits presented only one isokinetic curve T_B = 315.7 ± 3.5 K (42.7 °C), for raisins, currants and figs (75.2–82.3% d.b. sugars) and T_B = 317.7 ± 4.6 K (44.7 °C) for prunes and apricots (51.5–54.5% d.b. sugars), indicating an enthalpy-controlled adsorption process for the whole range of moisture contents covered.     

The use of muscle protein solubility measurements to assess pig lean meat quality

The relationships between sarcoplasmic, myofibrillar and total soluble protein (sarcoplasmic + myofibrillar) concentrations, and subjective (colour-structure score) and objective (drip loss and reflectance) measures of lean meat quality were determined using 100 samples of M. Longissimus dorsi that showed a wide range of quality. There was good agreement between the subjective and objective assessments of quality. Overall, the concentration of soluble sarcoplasmic proteins showed the highest correlations with quality assessments. The relationships with total soluble protein were poorer and were least good with myofibrillar protein concentration. Sarcoplasmic protein concentration was also the best potential predictor of meat quality when pale, soft, exudative (PSE) muscles were excluded from the sample. However, if dark, firm, dry (DFD) muscles were excluded instead, the concentration of total soluble protein was as good as, or better than, sarcoplasmic protein as a potential predictor of quality, particularly muscle reflectance.     

P(y)-a parameter for meat quality

The P_y is a parameter which assesses the integrity of the cell membranes. It is a direct indicator for the volume fraction of cells surrounded by insulating cell membranes. The P_y has been shown to correlate well with meat quality parameters like the drip loss or pH. It is a useful parameter for the discrimination between normal suited meat and PSE meat. The measurement is instantaneous and nondestructive. Due to aging of meat, P_y depends on the time post mortem. It shows the highest significance between 4 and 24 h p.m.