A study on the cycle performance of lithium secondary batteries using lithium nickel-cobalt composite oxide and graphite/coke hybrid carbon

10 Wh-class (30650 type) lithium secondary batteries were fabricated using LiNi_0.7Co_0.3O₂ as the positive electrode material and graphite/coke hybrid carbon as the negative electrode material. In our previous work, we found that LiNi_0.7Co_0.3O₂ and graphite/coke hybrid carbon each provide a longer cycle life among several candidates (Kida et al., J. Power Sources 94 (2001) 74; Kida et al., in preparation; Kinoshita et al., J. Power Sources 102 (2001) 284). In this study, the cycle performance of cells using both LiNi_0.7Co_0.3O₂ and graphite/coke hybrid carbon was examined and the deterioration factor of the discharge capacity was investigated during charge/discharge tests. We then focused our interest on the negative electrode and analyzed it using ⁷Li nuclear magnetic resonance (NMR) spectroscopy, X-ray photoelectron spectroscopy (XPS), and electrochemical impedance spectroscopy (EIS). After the discharge capacity of the battery deteriorated to 70% of the rated capacity after 2000 cycles, the graphite/coke hybrid carbon showed 91% of initial discharge capacity. When the solid electrolyte interface (SEI) (LiF, Li₂CO₃ and polymers) (E. Peled, J. Electrochem. Soc. 126 (1979) 2047) on the carbon negative electrode became thicker in the charge/discharge cycle test, the impedance was considered to have increased. This suggests that the deterioration of the graphite/coke hybrid carbon material is not so large, but that the production of the SEI on the negative electrode and impedance change of the negative electrode are factors of the capacity fade.     

Improvement of structural stability and electrochemical activity of a cathode material LiNi0.7Co0.3O2 by chlorine doping

In the process of Li⁺ intercalation-deintercalation, electron removal is accompanied simultaneously. Oxygen was found to compensate electron removal both in theoretical calculations and practical experiments. Chlorine addition to LiNi_0.7Co_0.3O₂ was expected to exchange electrons in that Cl⁻ was easier to lose electrons than O²⁻. LiNi_0.7Co_0.3O_2−xCl_x was identified as a pure hexagonal lattice of α-NaFeO₂ type by X-ray diffraction. X-ray photoelectron spectroscopy was used to analyze the influence of chlorine substitution on the oxidation state of transition-metal ions. Charge-discharge experiments and cyclic voltammetry confirmed that chlorine addition was an effective way to improve reversible capacity and structural stability in cycles.     

Effect of ZnO modification on the performance of LiNi0.5Co0.25Mn0.25O2 cathode material

ZnO was coated on LiNi_0.5Co_0.25Mn_0.25O₂ cathode (positive electrode) material for lithium ion battery via sol–gel method to improve the performance of LiNi_0.5Co_0.25Mn_0.25O₂. The X-ray diffraction (XRD) results indicated that the lattice structure of LiNi_0.5Co_0.25Mn_0.25O₂ was not changed distinctly after surface coating and part of Zn²⁺ might dope into the lattice of the material. Energy dispersive spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS) proved that ZnO existed on the surface of LiNi_0.5Co_0.25Mn_0.25O₂. Charge and discharge tests showed that the cycle performance and rate capability were improved by ZnO coating, however, the initial capacity decreased dramatically with increasing the amount of ZnO. Differential scanning calorimetry (DSC) results showed that thermal stability of the materials was improved. The XPS spectra after charge–discharge cycles showed that ZnO coated on LiNi_0.5Co_0.25Mn_0.25O₂ promoted the decomposition of the electrolyte at the early stage of charge–discharge cycle to form more stable SEI layer, and it also can scavenge the free acidic HF species from the electrolyte. The electrochemical impedance spectroscopy (EIS) results showed ZnO coating could suppress the augment of charge transfer resistance upon cycling.     

Characterization of electrode/electrolyte interface using in situ X-ray reflectometry and LiNi0.8Co0.2O2 epitaxial film electrode synthesized by pulsed laser deposition method

An in situ experimental technique was developed for detecting structure changes at the electrode/electrolyte interface of lithium cell using synchrotron X-ray reflectometry and two-dimensional model electrodes with a restricted lattice plane. The electrode was constructed with an epitaxial film of LiNi_0.8Co_0.2O₂ synthesized by the pulsed laser deposition method. The orientation of the epitaxial film depends on the substrate plane; the 2D layer of LiNi_0.8Co_0.2O₂ is parallel to the SrTiO₃ (1 1 1) substrate ((0 0 3)_{LiCo0.2Ni0.8O2}//(1 1 1)SrTiO₃), while the 2D layer is perpendicular to the SrTiO₃ (1 1 0) substrate ((1 1 0)_{LiCo0.2Ni0.8O2}//(1 1 0)SrTiO₃). These films provided an ideal reaction field suitable for detecting structure changes at the electrode/electrolyte interface during the electrochemical reaction. The X-ray reflectometry indicated a formation of a thin-film layer at the LiNi_0.8Co_0.2O₂ (1 1 0)/electrolyte interface during the first charge-discharge cycle, while the LiNi_0.8Co_0.2O₂ (0 0 3) surface showed an increase in the surface roughness without forming the surface thin-film layer. The reaction mechanism at the electrode/electrolyte interface is discussed based on our new experimental technique for lithium batteries.     

Comparison of structure and electrochemistry of Al- and Fe-doped LiNi1/3Co1/3Mn1/3O2

LiNi_1/3Co_1/3−xM_xMn_1/3O₂ (M = Fe and Al; x = 0, 1/20, 1/9 and 1/6) have been synthesized by firing the co-precipitates of metal hydroxides. The impacts of Fe and Al doping on the structure and electrochemical performances of LiNi_1/3Co_1/3Mn_1/3O₂ are compared by means of powder X-ray diffraction (XRD), scanning electron microscopy (SEM), and galvanostatic charge/discharge test as cathode materials for lithium ion batteries. These materials keep the same layered structure as the LiNi_1/3Co_1/3Mn_1/3O₂ host. It is found that Fe- and Al-doped LiNi_1/3Co_1/3Mn_1/3O₂ show different characteristics in lattice parameter and cycling voltage plateau with increasing dopant dose. More interestingly, low Al doping (x < 1/20) improves the structural stability while Fe doping does not have such effect even at low Fe content.     

Synthesis and characterization of abundant Ni-doped LiNixMn2−xO4 (x = 0.1-0.5) powders by spray-drying method

The structure and electrochemical properties of LiNi_xMn_2−xO₄ cathode materials for lithium ion batteries were studied by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscope (TEM), cyclic voltammetry, and galvanostatic charge-discharge tests. The cathodes with different Ni contents (LiNi_xMn_2−xO₄, x = 0.1, 0.2, 0.3, 0.4, and 0.5) were synthesized by a spray-drying method and showed a single-phase spinel structure without any impurity. The amount of Ni has a large effect on the electrochemical characteristics. Capacity values of different voltage ranges (4- and 5-V ranges) change obviously with amount of Ni-doped. Also, the total discharge capacities increase with the Ni content, and all of them have good cycle stability.     

Characterization of yttrium substituted LiNi0.33Mn0.33Co0.33O2 cathode material for lithium secondary cells

LiNi_0.33−xMn_0.33Co_0.33Y_xO₂ materials are synthesized by Y³⁺ substitute of Ni²⁺ to improve the cycling performance and rate capability. The influence of the Y³⁺ doping on the structure and electrochemical properties are investigated by means of X-ray diffraction (XRD), scanning electron microscope (SEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), X-ray photoelectron spectroscopy (XPS) and galvanostatic charge/discharge tests. LiNi_0.33Mn_0.33Co_0.33O₂ exhibits the capacity retentions of 89.9 and 87.8% at 2.0 and 4.0 C after 40 cycles, respectively. After doping, the capacity retentions of LiNi_0.305Mn_0.33Co_0.33Y_0.025O₂ are increased to 97.2 and 95.9% at 2.0 and 4.0 C, respectively. The discharge capacity of LiNi_0.305Mn_0.33Co_0.33Y_0.025O₂ at 5.0 C remains 75.7% of the discharge capacity at 0.2 C, while that of LiNi_0.33Mn_0.33Co_0.33O₂ is only 47.5%. EIS measurement indicates that LiNi_0.305Mn_0.33Co_0.33Y_0.025O₂ electrode has the lower impedance value during cycling. It is considered that the higher capacity retention and superior rate capability of Y-doped samples can be ascribed to the reduced surface film resistance and charge transfer resistance of the electrode during cycling.     

Synthesis of LiNi0.9Co0.1O2 from Li2CO3, NiO or NiCO3, and CoCO3 or Co3O4 and their electrochemical properties

Cathode active materials with a composition of LiNi_0.9Co_0.1O₂ were synthesized by a solid-state reaction method at 850 °C using Li₂CO₃, NiO or NiCO₃, and CoCO₃ or Co₃O₄, as the sources of Li, Ni, and Co, respectively. Electrochemical properties, structure, and microstructure of the synthesized LiNi_0.9Co_0.1O₂ samples were analyzed. The curves of voltage vs. x in Li_xNi_0.9Co_0.1O₂ for the first charge–discharge and the intercalated and deintercalated Li quantity Δx were studied. The destruction of unstable 3b sites and phase transitions were discussed from the first and second charge–discharge curves of voltage vs. x in Li_xNi_0.9Co_0.1O₂. The LiNi_0.9Co_0.1O₂ sample synthesized from Li₂CO₃, NiO, and Co₃O₄ had the largest first discharge capacity (151 mA h/g), with a discharge capacity deterioration rate of −0.8 mA h/g/cycle (that is, a discharge capacity increasing 0.8 mA h/g per cycle).     

Preparation and electrochemical properties of LiCoO2-LiNi0.5Mn0.5O2-Li2MnO3 solid solutions with high Mn contents

The solid solutions LiCoO₂-LiNi_1/2Mn_1/2O₂-Li₂MnO₃ with higher Mn content have been prepared by a spray drying method between 750 and 950 °C and their electrochemical performances have also been characterized. The effects of the Li content on the structure and electrochemical performance of the samples have been studied. It was found that their lattice parameters a, c and V increase with the increase in Ni content and the decrease in Co content. The solid solutions xLiCoO₂-yLiNi_1/2Mn_1/2O₂-(1−x−y)Li₂MnO₃ with x = 0.18, 0.27 and y = 0.2 have the largest discharge capacity, which is more than 200 mAh/g in the voltages of 3.0-4.6 V. It is believed that the optimum Co content x in xLiCoO₂-yLiNi_1/2Mn_1/2O₂-(1−x−y)Li₂MnO₃ is between 0.2 and 0.3 in the charge-discharge voltage range of 3.0-4.6 V. The solid solutions xLiCoO₂-yLiNi_1/2Mn_1/2O₂-(1−x−y)Li₂MnO₃ with x = 0.18-0.36 and y = 0.2 have the excellent cycling performance and the capacity retention attains to almost 100% after 50 cycles. Moreover, it is found that the discharge capacity gradually increases with the increment of cycle number especially in the initial 10 cycles. XRD showed that the layered structure has been kept all the time in 20 cycles, which is perhaps the reason why the sample has the excellent cycling performance.     

LiNi<Subscript>0.4</Subscript>Co<Subscript>0.3</Subscript>Mn<Subscript>0.3</Subscript>O<Subscript>2</Subscript> thin film electrode by aerosol deposition

LiNi_0.4Co_0.3Mn_0.3O₂ thin film electrodes are fabricated from LiNi_0.4Co_0.3Mn_0.3O₂ raw powder at room temperature without pretreatments using aerosol deposition that is much faster and easier than conventional methods such as vaporization, pulsed laser deposition, and sputtering. The LiNi_0.4Co_0.3Mn_0.3O₂ thin film is composed of fine grains maintaining the crystal structure of the LiNi_0.4Co_0.3Mn_0.3O₂ raw powder. In the cyclic voltammogram, the LiNi_0.4Co_0.3Mn_0.3O₂ thin film electrode shows a 3.9-V anodic peak and a 3.6-V cathodic peak. The initial discharge capacity is 44.6 μAh/cm², and reversible behavior is observed in charge-discharge profiles. Based on the results, the aerosol deposition method is believed to be a potential candidate for the fabrication of thin film electrodes.     

Modeling the impedance versus voltage characteristics of LiNi0.8Co0.15Al0.05O2

The power-delivery capability of lithium-ion cells based on LiNi_0.8Co_0.15Al_0.05O₂-based positive electrodes shows a significant dependence on the cell's state-of-charge. One reason for this behavior is the variation of the positive electrode's impedance with the oxide's lithium content. In this article, an electrochemical model based on concentrated solution porous electrode theory is used to model impedance data obtained on LiNi_0.8Co_0.15Al_0.05O₂-based positive electrodes charged to potentials ranging from 3.55 to 4.55 V versus Li. The parameters obtained from model fits include the exchange-current density and Li-ion diffusion coefficients in the oxide. The variations in these parameters with oxide potential are correlated with structural changes in the material observed during Li-ion intercalation-deintercalation reactions.     

Improved electrochemical properties of Li1+x(Ni0.3Co0.4Mn0.3)O2−δ (x = 0, 0.03 and 0.06) with lithium excess composition prepared by a spray drying method

Layered Li_1+x(Ni_0.3Co_0.4Mn_0.3)O_2−δ (x = 0, 0.03 and 0.06) materials were synthesized through the different calcination times using the spray-dried precursor with the molar ratio of Li/Me = 1.25 (Me = transition metals). The physical and electrochemical properties of the lithium excess and the stoichiometric materials were examined using XRD, AAS, BET and galvanostatic electrochemical method. As results, the lithium excess Li_1.06(Ni_0.3Co_0.4Mn_0.3)O_2−δ could show better electrochemical properties, such as discharge capacity, capacity retention and C rate ability, than those of the stoichiometric Li_1.00(Ni_0.3Co_0.4Mn_0.3)O_2−δ. In this paper, the effect of excess lithium on the electrochemical properties of Li_1+x(Ni_0.3Co_0.4Mn_0.3)O_2−δ materials will be discussed based on the experimental results of ex situ X-ray diffraction, transmission electron microscopy (TEM) and galvanostatic intermittent titration technique (GITT)     

Preparation and characterization of partially substituted LiMyMn2−yO4 (M=Ni, Co, Fe) spinel cathodes for Li-ion batteries

The electrochemical and thermal behaviors of the spinels-LiMn₂O₄, LiCo_1/6Mn_11/6O₄, LiFe_1/6Mn_11/6O₄, and LiNi_1/6Mn_11/6O₄ were studied using electrochemical and thermochemical techniques. The electrochemical techniques included cyclic voltammetry, charge-discharge cycling of 2016 coin cells and diffusion coefficient measurements using Galvanostatic Intermittent Titration Technique. Better capacity retention was observed for the substituted spinels (0.11% loss per cycle for LiCo_1/6Mn_11/6O₄; 0.3% loss per cycle for LiFe_1/6Mn_11/6O₄; and 0.2% loss per cycle for LiNi_1/6Mn_11/6O₄) than for the lithium manganese dioxide spinel (1.6% loss per cycle for first ten cycles, 0.9% loss per cycle for 33 cycles) during 33 cycles. The Differential Scanning Calorimetry results showed that the cobalt substituted spinel has better thermal stability than the lithium manganese oxide and other substituted spinels.     

A delithiated LiNi0.65Co0.25Mn0.10O2 electrode material: A structural, magnetic and electrochemical study

A crystalline LiNi_0.65Co_0.25Mn_0.10O₂ electrode material was synthesized by the combustion method at 900 °C for 1 h. Rietveld refinement shows less than 3% of Li/Ni disorder in the structure. Lithium extraction involves only the Ni²⁺/Ni⁴⁺ redox couple while Co³⁺ and Mn⁴⁺ remain electrochemically inactive. No structural transition was detected during cycling in the whole composition range 0 < x < 1.0. Furthermore, the hexagonal cell volume changes by only 3% when all lithium was removed indicating a good mechanical stability of the studied compound. LiNi_0.65Co_0.25Mn_0.10O₂ has a discharge capacity of 150 mAh/g in the voltage range 2.5-4.5 V, but the best electrochemical performance was obtained with an upper cut-off potential of 4.3 V. Magnetic measurements reveal competing antiferromagnetic and ferromagnetic interactions - varying in strength as a function of lithium content - yielding a low temperature magnetically frustrated state. The evolution of the magnetic properties with lithium content confirms the preferential oxidation of Ni ions compared to Co³⁺ and Mn⁴⁺ during the delithiation process.     

Synthesis and electrochemical properties of submicron LiNi0.8Co0.2O2 by a polymer-pyrolysis method

A polymer-pyrolysis method was used to synthesize LiNi_0.8Co_0.2O₂, which has potential application in lithium ion batteries. The effect of calcination temperature and time on the structure and electrochemical performance of the material was investigated. XRD analysis showed that the powders obtained by calcination at 750 °C for 3 h had the best-ordered hexagonal layer structure. SEM image showed these powders were fine, narrowly distributed with platelet morphology. The charge-discharge tests demonstrated these powders had the best electrochemical properties, with an initial discharge capacity of 189 mAh/g and capacity retention of 95.2% after 50 cycles when cycled at 50 mA/g between 3.0 and 4.3 V. Besides, these powders also had exhibited excellent rate capability.     

Effects of surface modification on the cycling stability of LiNi0.8Co0.2O2 electrodes by CeO2 coating

A high-performance LiNi_0.8Co_0.2O₂ cathode was successfully fabricated by a sol-gel coating of CeO₂ to the surface of the LiNi_0.8Co_0.2O₂ powder and subsequent heat treatment at 700 °C for 5 h. The surface-modified and pristine LiNi_0.8Co_0.2O₂ powders were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), slow rate cyclic voltammogram (CV), and differential scanning calorimetry (DSC). Unlike pristine LiNi_0.8Co_0.2O₂, the CeO₂-coated LiNi_0.8Co_0.2O₂ cathode exhibits no decrease in its original specific capacity of 182 mAh/g (versus lithium metal) and excellent capacity retention (95% of its initial capacity) between 4.5 and 2.8 V after 55 cycles. The results indicate that the surface treatment should be an effective way to improve the comprehensive properties of the cathode materials for lithium ion batteries.     

Cycling-induced stress in lithium ion negative electrodes: LiAl/LiFePO4 and Li4Ti5O12/LiFePO4 cells

In this work, we examined the electrochemical behaviour of lithium ion batteries containing lithium iron phosphate as the positive electrode and systems based on Li-Al or Li-Ti-O as the negative electrode. These two systems differ in their potential versus the redox couple Li⁺/Li and in their morphological changes upon lithium insertion/deinsertion. Under relatively slow charge/discharge regimes, the lithium-aluminium alloys were found to deliver energies as high as 438 Wh kg⁻¹ but could withstand only a few cycles before crumbling, which precludes their use as negative electrodes. Negative electrodes consisting solely of aluminium performed even worse. However, an electrode made from a material with zero-strain associated to lithium introduction/removal such as a lithium titanate spinel exhibited good performance that was slightly dependent on the current rate used. The Li₄Ti₅O₁₂/LiFePO₄ cell provided capacities as high as 150 mAh g⁻¹ under C-rate in the 100th cycle.     

Structure and electrochemical characterization of LiNi<Subscript>0.3</Subscript>Co<Subscript>0.3</Subscript>Mn<Subscript>0.3</Subscript>Fe<Subscript>0.1</Subscript>O<Subscript>2</Subscript> cathode for lithium secondary battery

A lithium insertion material having the composition LiNi_0.3Co_0.3Mn_0.3Fe_0.1O₂ was synthesized by simple sol-gel method. The structural and electrochemical properties of the sample were investigated using X-ray diffraction spectroscopy (XRD) and the galvanostatic charge-discharge method. Rietvelt analysis of the XRD patterns shows that this compound can be classified as α-NaFeO₂ structure type (R3m; a=2.8689(5) Å and 14.296(5) Å in hexagonal setting). Rietvelt fitting shows that a relatively large amount of Fe and Ni ion occupy the Li layer (3a site) and a relatively large amount of Li occupies the transition metal layer (3b site). LiNi_0.3Co_0.3Mn_0.3Fe_0.1O₂ when cycled in the voltage range 4.3–2.8 V gives an initial discharge capacity of 120 mAh/g, and stable cycling performance. LiNi_0.3Co_0.3Mn_0.3Fe_0.1O₂ in the voltage range 2.8–4.5 V has a discharge capacity of 140 mAh/g, and exhibits a significant loss in capacity during cycling. Ex-situ XRD measurements were performed to study the structure changes of the samples after cycling between 2.8–4.3 V and 2.8–4.5 V for 20 cycles. The XRD and electrochemical results suggested that cation mixing in this layered structure oxide could be causing degradation of the cell capacity.     

A simple and effective method to synthesize layered LiNi0.8Co0.1Mn0.1O2 cathode materials for lithium ion battery

Nanocrystalline materials of Ni_0.8Co_0.1Mn_0.1(OH)₂ are successfully synthesized by fast co-precipitation method. The crystalline structure and morphology of the precursors and LiNi_0.8Co_0.1Mn_0.1O₂ materials are characterized by XRD, SEM and Rietveld refinement analyses. It is found that the nanocrystalline phase and low crystallinity of Ni_0.8Co_0.1Mn_0.1(OH)₂ could help achieve its uniform mixing with lithium source, and further attribute to highly ordered layered LiNi_0.8Co_0.1Mn_0.1O₂ with low cation mixing degree. Electrochemical studies confirm that the LiNi_0.8Co_0.1Mn_0.1O₂ exhibits a good electrochemical property with initial discharge specific capacity of 192.4 mAh g^− 1 at a current density of 18 mA g^− 1, and the capacity retention after 40 cycles is 91.56%. This method is a simple and effective method to synthesize cathode material.     

Aging characteristics of high-power lithium-ion cells with LiNi0.8Co0.15Al0.05O2 and Li4/3Ti5/3O4 electrodes

The impedance rise that results from the accelerated aging of high-power lithium-ion cells containing LiNi_0.8Co_0.15Al_0.05O₂-based positive and graphite-based negative electrodes is dominated by contributions from the positive electrode. Data from various diagnostic experiments have indicated that a general degradation of the ionic pathway, apparently caused by surface film formation on the oxide particles, produces the positive electrode interface rise. One mechanistic hypothesis postulates that these surface films are components of the negative electrode solid electrolyte interphase (SEI) layer that migrate through the electrolyte and separator and subsequently coat the positive electrode. This hypothesis is examined in this article by subjecting cells with LiNi_0.8Co_0.15Al_0.05O₂-based positive and Li_4/3Ti_5/3O₄-based negative electrodes to accelerated aging. The impedance rise in these cells was observed to be almost entirely from the positive electrode. Because reduction products are not expected on the 1.55 V Li_4/3Ti_5/3O₄ electrode, the positive electrode impedance cannot be attributed to the migration of SEI-type fragments from the negative electrode. It follows then that the impedance rise results from mechanisms that are “intrinsic” to the positive electrode.