Influence of solvent on the poly (acrylic acid)-oligo-(ethylene glycol) polymer gel electrolyte and the performance of quasi-solid-state dye-sensitized solar cells

The influence of solvents on the property of poly (acrylic acid)-oligo-(ethylene glycol) polymer gel electrolyte and photovoltaic performance of quasi-solid-state dye-sensitized solar cells (DSSCs) were investigated. Solvents or mixed solvents with large donor number enhance the liquid electrolyte absorbency, which further influences the ionic conductivity of polymer gel electrolyte. A polymer gel electrolyte with ionic conductivity of 4.45 mS cm⁻¹ was obtained by using poly (acrylic acid)-oligo-(ethylene glycol) as polymer matrix, and absorbing 30 vol.% N-methyl pyrrolidone and 70 vol.% γ-butyrolactone with 0.5 M NaI and 0.05 M I₂. By using this polymer gel electrolyte coupling with 0.4 M pyridine additive, a quasi-solid-state dye-sensitized solar cell with conversion efficiency of 4.74% was obtained under irradiation of 100 mW cm⁻² (AM 1.5).     

Gel polymer electrolyte based on poly(acrylonitrile-co-styrene) and a novel organic iodide salt for quasi-solid state dye-sensitized solar cell

A gel polymer electrolyte based on poly(acrylonitrile-co-styrene) as polymer matrix and N-methyl pyridine iodide salt as I⁻ source was prepared. Controlling the concentration of polymer matrix of poly(acrylonitrile-co-styrene) at 17.5 wt.%, mixing the binary organic solvents mixture ethylene carbonate and propylene carbonate with 6:4 (w/w), and the concentration of N-methyl pyridine iodide and iodine with 0.5 and 0.05 M, respectively, the gel polymer electrolyte attains the maximum ionic conductivity (at 30 °C) of 4.63 mS cm⁻¹. Based on the gel polymer electrolyte, a quasi-solid state dye-sensitized solar cell was fabricated and its overall energy conversion efficiency of light-to-electricity of 3.10% was achieved under irradiation of 100 mW cm⁻².     

New highly proton-conducting membrane poly(vinylpyrrolidone)(PVP) modified poly(vinyl alcohol)/2-acrylamido-2-methyl-1-propanesulfonic acid (PVA-PAMPS) for low temperature direct methanol fuel cells (DMFCs)

A new type of chemically cross-linked polymer blend membranes consisting of poly(vinyl alcohol) (PVA), 2-acrylamido-2-methyl-1-propanesulfonic acid (PAMPS) and poly(vinylpyrrolidone) (PVP) have been prepared and evaluated as proton conducting polymer electrolytes. The proton conductivity (σ) of the membranes was investigated as a function of cross-linking time, blending composition, water content and ion exchange capacity (IEC). Membranes were also characterized by FT-IR spectroscopy, thermogravimetric analysis (TGA), and the differential scanning calorimetry (DSC). Membrane swelling decreased with cross-linking time, accompanied by an improvement in mechanical properties and a small decrease in proton conductivity due to the reduced water absorption. The membranes attained 0.088 S cm⁻¹ of the proton conductivity and 1.63 mequiv g⁻¹ of IEC at 25±2 °C for a polymer composition PVA-PAMPS-PVP being 1:1:0.5 in mass, and a methanol permeability of 6.1×10⁻⁷ cm² s⁻¹, which showed a comparable proton conductivity to Nafion 117, but only one third of Nafion 117 methanol permeability under the same measuring conditions. The membranes displayed a relatively high oxidative durability without weight loss of the membranes (e.g. 100 h in 3% H₂O₂ solution and 20 h in 10% H₂O₂ solution at 60 °C). PVP, as a modifier, was found to play a crucial role in improving the above membrane performances.     

Synthesis and electrochemical properties of lithium methacrylate-based self-doped gel polymer electrolytes

In this study, a strategy for synthesizing lithium methacrylate (LiMA)-based self-doped gel polymer electrolytes was described and the electrochemical properties were investigated by impedance spectroscopy and linear sweep voltammetry. LiMA was found to dissolve in ethylene carbonate (EC)/diethyl carbonate (DEC) (3/7, v/v) solvent after complexing with boron trifluoride (BF₃). This was achieved by lowering the ionic interactions between the methacrylic anion and lithium cation. As a result, gel polymer electrolytes consisting of BF₃-LiMA complexes and poly(ethylene glycol) diacrylate were successfully synthesized by radical polymerization in an EC/DEC liquid electrolyte. The FT-IR and AC impedance measurements revealed that the incorporation of BF₃ into the gel polymer electrolytes increases the solubility of LiMA and the ionic conductivity by enhancing the ion disassociations. Despite the self-doped nature of the LiMA salt, an ionic conductivity value of 3.0 × 10⁻⁵ S cm⁻¹ was achieved at 25 °C in the gel polymer electrolyte with 49 wt% of polymer content. Furthermore, linear sweep voltammetry measurements showed that the electrochemical stability of the gel polymer electrolyte was around 5.0 V at 25 °C.     

Anhydrous proton conducting polymer electrolytes based on poly(vinylphosphonic acid)-heterocycle composite material

The development of anhydrous proton conducting membrane is important for the operation of polymer electrolyte membrane fuel cell (PEMFC) at intermediate temperature (100-200 °C). In this study, we have investigated the acid-base hybrid materials by mixing of strong phosphonic acid polymer of poly(vinylphosphonic acid) (PVPA) with the high proton-exchange capacity and organic base of heterocycle, such as imidazole (Im), pyrazole (Py), or 1-methylimidazole (MeIm). As a result, PVPA-heterocycle composite material showed the high proton conductivity of approximately 10⁻³ S cm⁻¹ at 150 °C under anhydrous condition. In particular, PVPA-89 mol% Im composite material showed the highest proton conductivity of 7×10⁻³ S cm⁻¹ at 150 °C under anhydrous condition. Additionally, the fuel cell test of PVPA-89 mol% Im composite material using a dry H₂/O₂ showed the power density of approximately 10 mW cm⁻² at 80 °C under anhydrous conditions. These acid-base anhydrous proton conducting materials without the existence of water molecules might be possibly used for a polymer electrolyte membrane at intermediate temperature operations under anhydrous or extremely low humidity conditions.     

Preparation of poly(acrylonitrile-butyl acrylate) gel electrolyte for lithium-ion batteries

Poly(acrylonitrile-butyl acrylate) gel polymer electrolyte was prepared for lithium ion batteries. The preparation started with synthesis of poly(acrylonitrile-butyl acrylate) by radical emulsion polymerization, followed by phase inversion to produce microporous membrane. Then, the microporous gel polymer electrolytes (MGPEs) was prepared with the microporous membrane and LiPF₆ in ethylene carbonate/diethyl carbonate. The dry microporous membrane showed a fracture strength as high as 18.98 MPa. As-prepared gel polymer electrolytes presented ionic conductivity in excess of 3.0 × 10⁻³ S cm⁻¹ at ambient temperature and a decomposition voltage over 6.6 V. The results showed that the as-prepared gel polymer electrolytes were promising materials for Li-ion batteries.     

Composite polyether electrolytes with a poly(styrenesulfonate) lithium salt and Lewis acid type additive

A poly(styrenesulfonate) lithium salt was tested as a single-ion conductor in a poly(ethylene oxide)/poly(ethylene glycol) dimethyl ether matrix. Impedance spectroscopy and voltage step polarization were used to characterize the composite electrolytes. A specific conductivity of about 7×10⁻⁸ S cm⁻¹ was evaluated at 70 °C. The very low conductivity was attributed to the poor solubility of Li⁺ in the polymer matrix. AlCl₃ was added to the polymer electrolyte to increase the salt dissolution. The addition of the Lewis acid strongly increases the conductivity and a specific conductivity of about 4×10⁻⁶ S cm⁻¹ was measured at 20 °C. For temperature lower than 60 °C, the specific conductivity dependence with increasing temperature follows an Arrhenius-type behavior. An activation energy of about 55.6 kJ mol⁻¹ was calculated. A very similar activation energy (60.3 kJ mol⁻¹) was found for the charge transfer resistance. The transport properties of the polymer electrolyte were tested by applying a d.c. voltage step to a symmetrical lithium cell. The current at the applied voltage decreased with time. The decrease was related to an increase in the cell resistance due to the continuous growth of a passivation layer on the lithium surface.     

Polymer electrolytes based on poly(ethylene glycol) dimethyl ether and the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate: Preparation, physico-chemical characterization, and theoretical study

Polymer electrolytes based on poly(ethylene glycol) dimethyl ether (PEGdME) and the ionic liquid (IL) 1-butyl-3-methylimidazolium hexafluorophosphate ([bmim]PF₆) have been prepared and characterized by different techniques. Coordination of the IL by the polymer occurs mainly in the amorphous phase. This finding was correlated with previous theoretical investigations of a similar model for polymer electrolytes based on poly(ethylene oxide), PEO, and IL. It has been obtained ionic conductivity σ ∼ 10⁻³ S cm⁻¹ for the polymer electrolyte with 35 wt% of IL at 100 °C. The same order of magnitude for σ was obtained by molecular dynamics simulation of PEO/IL. This work demonstrates consistency between experimental and theoretical results for polymer electrolytes containing ionic liquids.     

Influence of molecular weight of PEG on the property of polymer gel electrolyte and performance of quasi-solid-state dye-sensitized solar cells

A new kind of polymer gel electrolyte based on poly(acrylic acid)-poly(ethylene glycol) (PAA-PEG) hybrid was synthesized. The factor of molecular weight of PEG in the hybrid plays an important role in determining the liquid electrolyte absorbency of the hybrid and ionic conductivity of the polymer gel electrolyte, sequentially affects the photovoltaic performance of quasi-solid-state dye-sensitized solar cells. Using the hybrid with PEG molecular weight of 20,000, a polymer gel electrolyte with liquid electrolyte absorbency of 6.9 g g⁻¹ and ionic conductivity of 5.35 mS cm⁻¹ was obtained. Based on the polymer gel electrolyte, a quasi-solid-state dye-sensitized solar cell with conversion efficiency of 5.25% was achieved under irradiation of AM 1.5, 100 mW cm⁻².     

Electric double layer capacitors with gelled polymer electrolytes based on poly(ethylene oxide) cured with poly(propylene oxide) diamines

Using a gel electrolyte for electric double layer capacitors usually encountered a drawback of poor contact between the electrolyte and the electrode surface. A gel electrolyte consisting of poly(ethylene oxide) crosslinked with poly(propylene oxide) as a host, propylene carbonate (PC) as a plasticizer, and LiClO₄ as a electrolytic salt was synthesized for double layer capacitors. Diglycidyl ether of bisphenol-A was blended with the polymer precursors to enhance the mechanical properties and increase the internal free volume. This gel electrolyte showed an ionic conductivity as high as 2 × 10⁻³ S cm⁻¹ at 25 °C and was electrochemically stable over a wide potential range (ca. 5 V). By sandwiching this gel-electrolyte film with two activated carbon cloth electrodes (1100 m² g⁻¹ in surface area), we obtained a capacitor with a specific capacitance of 86 F g⁻¹ discharged at 0.5 mA cm⁻², while the capacitance was 82 F g⁻¹ for a capacitor equipped with a liquid electrolyte of 1 M LiClO₄/PC. The capacitance decrease with the current density was less significant for the gel-electrolyte capacitor. We found that the less restricted ion diffusion near the electrolyte/electrode interface led to the smaller overall resistance of the gel-electrolyte capacitor. The high performance of the gel-electrolyte capacitor has demonstrated that the developed polymer network not only facilitated ion motion in the electrolyte bulk phase but also gave an intimate contact with the carbon surface. The side chains of the polymer in the amorphous phase could stretch across the boundary layer at the electrolyte/electrode interface to come into contact with the carbon surface, thus improving transport of Li⁺ ions by the segmental mobility in polymer.     

Intrinsically proton-conducting poly(1-vinyl-1,2,4-triazole)/triflic acid blends

In the present work, proton conductivity in a polymer blend comprising proton solvating heterocycles was examined. Poly(1-vinyl-1,2,4-triazole), PVTri was produced by free radical polymerization of 1-vinyl-1,2,4-triazole and then proton-conducting polymer electrolytes were obtained by blending of PVTri with trifluoromethanesulfonic acid, triflic acid (TA). To promote the intrinsic proton conductivity the percent blending ratio was changed from 25% to 150% with respect to polymer repeat unit. The protonation of aromatic heterocyclic rings was proved with Fourier-transform infrared spectroscopy (FT-IR). Thermogravimetry (TG) analysis showed that the samples are thermally stable up to approximately 300 °C. Differential scanning calorimetry (DSC) results illustrated that the samples are homogeneous and their glass transition temperatures are located within 130-160 °C. The surface morphology of the materials were characterized by scanning electron microscopy (SEM). The proton conductivity of the blends increased with triflic acid concentration and the temperature. In the anhydrous state, the proton conductivity of PVTriTA100 is 2.2 × 10⁻⁴ S/cm at 150 °C and that of PVTriTA150 is approximately 0.012 S/cm at 80 °C which is similar to that of hydrated Nafion^®.     

Hybrid proton-conducting membranes for polymer electrolyte fuel cells: Phosphomolybdic acid doped poly(2,5-benzimidazole)—(ABPBI-H3PMo12O40)

The synthesis and characterization of a novel hybrid organic-inorganic material formed by phosphomolybdic acid H₃PMo₁₂O₄₀ (PMo₁₂) and poly(2,5-benzimidazole) (ABPBI) is reported. This material, composed of two proton-conducting components, can be cast in the form of membranes from methanesulfonic acid (MSA) solutions. Upon impregnation with phosphoric acid, the hybrid membranes present higher conductivity than the best ABPBI polymer membranes impregnated in the same conditions. These electrolyte membranes are stable up to 200 °C, and have a proton conductivity of 3 × 10⁻² S cm⁻¹ at 185 °C without humidification. These properties make them very good candidates as membranes for polymer electrolyte membrane fuel cells (PEMFC) at temperatures of 100-200 °C.     

The study on the conductivity and morphology of polyurethaneurea electrolytes based on poly(ethylene glycol) 2000 and LiClO4

Polyurethaneureas (PUU), which were synthesized from 4,4′-diphenylmethane diisocyanate (MDI), poly(ethylene glycol) (PEG, MW=2000), and 3,5-diaminobenzoic acid, were used as the matrix of the polyelectrolytes in this study. Differential scanning calorimetry (DSC), Fourier-transform infrared spectroscopy (FT-IR), and ⁷Li magic angle spinning (MAS) solid-state NMR were used to monitor changes in the morphology of PUU electrolytes corresponding to the concentration of lithium perchlorate (LiClO₄) dopants. The results of DSC and FT-IR indicate the different polymer complexes formed by the interaction of the Li⁺ ions with the different coordination sites of PUU. The ⁷Li MAS solid-state NMR investigation of the PUU electrolytes points out that two different Li⁺ environments exist at lower temperature. The results of DSC and the ⁷Li MAS solid-state NMR show that Li⁺ ions are preferentially coordinated to the ether oxygen of the PEG soft-segment when the salt concentration is below 0.1 mmol LiClO₄(gPUU)⁻¹. Impedance spectroscopy measurements show that the conductivity behavior followed the Arrhenius equation and was influenced by the hard-segment T_g. One of the PUU electrolytes under the investigation has an ionic conductivity as high as 3.0×10⁻⁵ S cm⁻¹ at 30 °C.     

Dye sensitized solar cells with poly(acrylonitrile) based plasticized electrolyte containing MgI2

Polymer electrolytes can be used favorably in photo-electrochemical solar cells. A possible electrolyte for this purpose is a polyacrylonitrile-MgI₂ complex with plasticizers such as ethylene carbonate and propylene carbonate. The best ionic conductivity was obtained for samples containing 60 wt% of MgI₂ salt with respect to the weight of polyacrylonitrile, for example, at 30 °C the conductivity is 1.9 × 10⁻³ S cm⁻¹. The ionic contribution to the conductivity is dominant as shown by dc polarization tests. Furthermore, the glass transition temperature showed a minimum, −103.0 °C, for the sample with the highest conductivity indicating the importance of polymer chain flexibility for the conduction process. Measurements on a fabricated solar cell with this electrolyte exhibited an overall energy conversion efficiency of 0.84%. The short circuit current density, open circuit voltage and fill factor of the cell were 2.04 mA cm⁻², 692 mV and 59.3%, respectively.     

A novel polymeric gel electrolyte systems containing magnesium salt with ionic liquid

A new polymeric gel electrolyte system consisting of poly(ethylene oxide)-modified polymethacrylate (PEO-PMA) with organic ionic liquid dissolving magnesium salt, Mg[(CF₃SO₂)₂N]₂, has been developed. The ionic conductance and electrochemical properties of the gel films were investigated. The obtained gel film was self-standing, transparent and flexible with sufficient mechanical strength. Thermal analysis of the gel film showed that it is homogeneous and amorphous over a wide temperature range. The highest conductivity, ca. 3.5 mS cm⁻¹ at 60 °C, was obtained for the polymeric gel containing 80 wt.% of the liquid component that consists of 80 mol% of EMITFSI (1-ethyl-3-methylimidazolium bis(trofluoromethylsulfonyl)imide) and 20 mol% of Mg[(CF₃SO₂)₂N]₂. The sort of the ionic liquid affected much on the ionic conductivity of the gel. The dc polarization of a Pt/polymeric gel electrolyte/Mg cell proved that the magnesium ion (Mg²⁺) can mobile in the present polymeric gel system.     

Proton conducting polydimethylsiloxane/zirconium oxide hybrid membranes added with phosphotungstic acid

Inorganic polymer based hybrid membranes consisting of zirconium oxide and polydimethylsiloxane (PDMS) have been synthesized by sol-gel processes. The organic/inorganic polymeric hybrid membranes showed thermal stability and flexibility up to 300 °C. The membrane becomes proton conducting polymer electrolyte when added with 12-phosphotungstic acid (PWA). The conductivity of the membranes was measured in the temperature range from room temperature to 150 °C under saturated humidity and a maximum conductivity of 5×10⁻⁵ S cm⁻¹ was obtained at 150 °C.     

Amphiphilic poly(vinyl chloride)-g-poly(oxyethylene methacrylate) graft polymer electrolytes: Interactions, nanostructures and applications to dye-sensitized solar cells

An amphiphilic graft copolymer, i.e. poly(vinyl chloride)-graft-poly(oxyethylene methacrylate) (PVC-g-POEM) comprised of a PVC backbone and POEM side chains was synthesized via atom transfer radical polymerization (ATRP) and complexed with a salt for dye-sensitized solar cell (DSSC) applications. The coordinative interactions and structural changes of polymer electrolytes were investigated using FT-IR spectroscopy, wide angle X-ray scattering (WAXS) and differential scanning calorimetry (DSC). Small angle X-ray scattering (SAXS) and transmission electron microscopy (TEM) revealed that the d-spacing between PVC domains was significantly increased upon the introduction of metal salt, ionic liquid and oligomer, indicating their selective confinement in the hydrophilic POEM domains. The ion-conducting POEM domains were well interconnected, resulting in high ionic conductivity (∼10⁻⁴ S/cm at 25 °C) and energy conversion efficiency (∼5.0% at 100 mW/cm²) in the solid-state.     

Synthesis and characterization of poly(1-vinyl-3-alkylimidazolium) iodide polymers for quasi-solid electrolytes in dye sensitized solar cells

A series of new poly(1-vinyl-3-alkylimidazolium) iodide polymers with different alkyl derivatives such as methyl, propyl and perflurodecyl have been synthesized. The alkyl substituent influenced some properties such as solubility, thermal stability, glass transition and crystallinity of the polymers. For instance, polymer having the propyl substituent was soluble in solvents of intermediate polarity such as acetonitrile, chloroform and THF, the one with the methyl substituent was only soluble in very polar solvents such as water and methanol and the fluorinated polymer was only soluble in DMF. The alkyl substituent also influenced the thermal stability in the order methyl > propyl > perflurodecyl and all the polymers thermally decomposed between 250 and 400 °C in nitrogen. The poly(1-vinyl-3-alkyl-imidazolium) iodide polymers having propyl and methyl substituents were amorphous polymers showing a glass transition temperature of 43 and 21 °C, respectively; and perflurodecyl polymers were semi-crystalline with a Tm at 153 °C and a Tg at 20 °C, as indicated by differential scanning calorimetry.Polymer electrolytes were formulated as mixtures of the ionic liquid 1-methyl-3-propylimidazolium iodide and the poly(1-vinyl-3-alkylimidazolium) iodide polymers. These polymer electrolytes showed ionic conductivities in the range of 10⁻³ to 10⁻⁷ S/cm at room temperature which strongly depended on the ionic liquid content. Finally, poly(1-vinyl-3-propyl-imidazolium) iodide was used to obtain gel electrolytes by adding it to a typical acetonitrile electrolyte used in dye sensitized solar cells (DSSCs). Solar cells with 1 cm² area prepared using the polymer gel electrolyte yielded a maximum light-to-electricity conversion efficiency of 3.73%.     

Influence of ionic additives NaI/I2 on the properties of polymer gel electrolyte and performance of quasi-solid-state dye-sensitized solar cells

The ionic additives NaI/I₂ in polymer gel electrolyte not only provide cations, but also affect the liquid electrolyte absorbency of the poly(acrylic acid)-poly(ethylene glycol) hybrid, which results in the change of ionic conductivity of polymer gel electrolyte and the photovoltaic performance of quasi-solid-state dye-sensitized solar cell. With the optimized components of liquid electrolyte containing 0.5 M NaI, 0.05 M I₂, 0.4 M pyridine, 70 vol.% γ-butyrolactone and 30 vol.% N-methylpyrrolidone, a 4.74% power conversion efficiency of quasi-solid-state dye-sensitized solar cell was obtained under 100 mW cm⁻² (AM 1.5) irradiation.     

Preparation of a microporous polymer electrolyte based on poly(vinyl chloride)/poly(acrylonitrile-butyl acrylate) blend for Li-ion batteries

Poly(acrylonitrile-co-butyl acrylate) (P(AN-co-BuA))/poly(vinyl chloride) (PVC) blend-based gel polymer electrolyte (BGPE) was prepared for lithium-ion batteries. The P(AN-co-BuA)/PVC BGPE consists of an electrolyte-rich phase, which is mainly composed of P(AN-co-BuA) and liquid electrolyte, acting as a conducting channel and a PVC-rich phase that provides mechanical strength. The dual phase was just simply developed by the difference of miscibility properties in solvent, PC, between P(AN-co-BuA) and PVC. The mechanical strength of this new blend electrolyte was found to be much higher, with a fracture stress as high as 29 MPa in dry membrane and 21 MPa in gel state, than that of a previously reported P(AN-co-BuA)-based gel polymer electrolyte. The blended gel polymer electrolyte showed ionic conductivity of higher than 1.5 × 10⁻³ S cm⁻¹ and electrochemical stability up to at least 4.8 V. The results showed that the as-prepared gel polymer electrolytes were promising materials for lithium-ion batteries.