考虑输入饱和的近空间飞行器姿态容错控制

针对近空间飞行器姿态控制中出现的执行器故障,输入饱和与外部干扰等问题,设计了一种基于二阶滑模干扰观测器和辅助系统的鲁棒容错跟踪控制方法.首先,将系统不确定,外部扰动和执行器故障作为复合干扰,设计super-twisting二阶滑模干扰观测器对其进行估计.然后为解决输入饱和问题构造了辅助分析系统,并借助backstepping方法,设计姿态容错跟踪控制器.利用Lyapunov方法,严格证明了所有闭环系统信号的收敛性.最后将所设计的控制方法应用于近空间飞行器姿态控制中,仿真结果验证了该控制方法的有效性.     

输入受限四旋翼飞行器的模糊自适应动态面轨迹跟踪控制

针对输入受限条件下四旋翼飞行器的轨迹跟踪控制问题,考虑系统存在模型动态不确定和未知外界干扰的情况,提出一种模糊自适应动态面轨迹跟踪控制方法.该方法设计干扰观测器估计位置模型中复合扰动项,利用模糊系统逼近姿态模型中不确定项和外界干扰,并引入双曲正切函数和辅助系统处理输入受限问题,结合反演法和动态面技术设计轨迹跟踪控制器,以降低控制算法的复杂性,最后选取李雅普诺夫函数证明闭环系统所有信号一致最终有界.应用大疆M100飞行器模型进行仿真验证,结果表明所设计的控制器能够有效处理模型动态不确定和未知外界干扰问题,避免飞行器工作过程中因输入饱和导致执行器失效现象,精确地完成轨迹跟踪控制任务.     

考虑执行器性能约束的刚体航天器鲁棒姿态跟踪控制

针对存在模型不确定性、外界干扰力矩和执行器性能受限等约束条件下的刚体航天器姿态跟踪控制问题进行研究,并基于滑模控制、反步控制、自适应控制、辅助系统和动态面控制等方法设计相应的鲁棒姿态跟踪控制算法.利用自适应控制实现了对具有多项式形式上界函数的系统未知不确定性进行在线估计和补偿;通过建立描述执行器动态特性的低通滤波模型,并结合辅助系统方法,以确保执行器输出控制力矩的幅值及其变化率均满足一定的饱和约束;通过引入动态面控制法,避免期望虚拟控制信号的一阶导数项直接出现在控制器中,简化了闭环姿态跟踪控制器的设计形式.最后,通过数值仿真验证了所提出控制算法的有效性和可行性.     

一类输入受限的不确定非仿射非线性系统二阶动态terminal 滑模控制

针对一类输入受限的不确定非仿射非线性系统跟踪控制问题, 提出一种二阶动态terminal 滑模控制策略. 在不损失模型精度, 并考虑系统输入饱和受限的前提下, 给出一种适用于全局的不确定非仿射非线性系统近似方法. 提出小波小脑模型干扰观测器设计方法, 实现复合扰动的有效逼近. 构造辅助系统分析输入饱和对跟踪误差的影响. 通过构造基于PI 滑模面的terminal 二阶滑模面, 给出二阶动态terminal 滑模控制器设计过程, 克服了传统滑模的抖振问题. 仿真结果验证了所提出方法的有效性.

     

基于反步滑模算法的无人机姿态鲁棒控制系统设计

针对传统无人机姿态鲁棒控制系统易受到外部干扰影响,无法精准控制姿态角、左侧舵面角和右侧舵面角,导致系统不稳定的问题,设计了基于反步滑模算法的无人机姿态鲁棒控制系统;使用TMS320F28335芯片的串级PID控制器,控制无人机中央处理机;选择MS-S3型伺服驱动器保证电机高速运动时的高转矩运行;使用STM32f407VGT6型号姿态控制器,控制旋翼姿态;在软件流程设计过程中,构建无人机动力学模型,引入反步滑模算法构建考虑姿态角动态方程,选择Lyapunov函数计算误差变量,设计滑模控制律,借助Visual C++6.0实现软件程序编写,完成无人机姿态鲁棒控制系统设计;由实验结果可知,在时间为5 s时,该系统姿态角达到6°、左侧舵面达到0.40°、右侧舵面角达到0.20°,与实际控制结果一致,具有精准控制效果。     

基于干扰观测器的一类不确定非线性系统自适应二阶动态terminal滑模控制

针对一类不确定非线性系统的跟踪控制问题,在考虑建模误差、参数不确定和外部干扰情况下,以其拥有良好的跟踪性能以及强鲁棒性为目标,提出基于回归扰动模糊神经网络干扰观测器(recurrent perturbation fuzzy neural networks disturbance observer,RPFNNDO)的鲁棒自适应二阶动态terminal滑模控制策略.将回归网络、模糊神经网络和sine-cosine扰动函数各自优势相结合,给出一种回归扰动模糊神经网络结构,提出RPFNNDO设计方法,保证干扰估计准确性;构造基于带有指数函数滑模面的二阶快速terminal滑模面,给出其控制器设计过程,避免了滑模到达阶段、传统滑模的抖振问题,采用具有指数收敛的鲁棒项抑制干扰估计误差对系统跟踪性能的影响,利用Lyapunov理论证明闭环系统的稳定性;将该方法应用于混沌陀螺系统同步控制仿真实验,结果表明所提方法的有效性.     

基于滑模控制的折叠翼飞行器辅助机动研究

基于滑模控制策略,研究了折叠翼飞行器辅助机动问题.分析了系统折叠角与气动参数的关系,把机翼折叠角看成额外的控制输入,构造了包含折叠辅助机动的飞行器动力学模型.针对非线性系统,加入混合干扰,设计了非奇异动态终端滑模控制(NDTSMC)器,能够较好地抑制折叠翼飞行器的不确定性,同时完成姿态跟踪控制.仿真结果表明,NDTSMC改善了折叠翼飞行器的控制精度和鲁棒性能,具有较好的抖振消除效果.与传统飞行器相比,加入折叠辅助机动的折叠翼飞行器拥有更高的机动性和抗干扰能力.     

基于自组织小波小脑模型关节控制器的不确定非线性系统鲁棒自适应终端滑模控制

针对一类不确定非线性系统的跟踪控制问题,在考虑建模误差、参数不确定和外部干扰情况下,以良好的跟踪性能及强鲁棒性为目标,提出基于自组织小脑模型(self-organizing wavelet cerebellar model articulation controller,SOWCMAC)的鲁棒自适应积分末端(terminal)滑模控制策略.首先,将小脑模型、自组织神经网络和小波函数各自优势相结合,给出一种SOWCMAC,以保证干扰估计方法具有快速学习能力和更好的泛化能力.其次,设计两种改进的terminal滑模面构造方法,并分别给出各自的收敛时间.然后,基于SOWCMAC和改进的积分terminal滑模面,给出不确定非线性系统鲁棒自适应非奇异terminal控制器的设计过程,其中通过构造自适应鲁棒项抑制干扰估计误差对系统跟踪性能的影响,并利用Lyapunov理论证明闭环系统的稳定性.最后,将该方法应用于近空间飞行器姿态的控制仿真实验,结果表明所提出方法有效性.     

不确定动态系统的执行器故障检测与重构

讨论不确定动态系统的执行器故障检测与重构问题.以滑模观测器为基础,利用状态和输出变换方法与奇异值分解方法相结合对系统进行降阶,提出一种鲁棒故障重构观测器.给出了优化滑模策略,并作了严格论证,保证对系统不确定性具有鲁棒性和跟踪系统状态的收敛性.应用等价输出控制的概念和设计的鲁棒故障重构观测器,获取故障信息并实现执行器故障的检测与重构.最后通过数值仿真验证了该方法的有效性和可靠性.     

多故障并发非线性系统一体化跟踪主动容错控制器设计

针对一类执行器及传感器同时发生故障的非线性系统,综合鲁棒滑模重构观测器及自适应滑模容错控制器设计技术,提出一体化跟踪主动容错控制方案.首先,将系统增维变换为广义系统,运用广义约束逆引入辅助矩阵,采用线性矩阵不等式设计观测器系数矩阵,综合自适应律给出广义鲁棒滑模观测器设计程式;在此基础之上,通过设计鲁棒滑模微分器估计输出向量微分,结合广义鲁棒滑模观测器状态估计结论,实现执行器及传感器故障同时重构.其次,基于故障重构及状态估计结论,提出自适应滑模的跟踪主动容错控制律设计程式.最后,通过开展飞行模拟转台伺服系统数值仿真,检验一体化跟踪主动容错控制器设计方法的有效性.     

输入有约束时的飞翼布局无人机姿态控制

针对大展弦比飞翼布局无人机的刚体运动与弹性运动耦合动力学模型,研究了输入有约束时的无人机姿态控制问题,提出了一种采用扩张状态观测器的反步滑模控制方法.首先,采用扩张状态观测器实时估计气动弹性模态和外界未知干扰的影响,并引入跟踪微分器避免了控制律中项数膨胀问题.然后,针对飞翼布局无人机多操纵面的配置和输入约束,给出了基于LMI的在线舵面分配算法.最后,针对指令滤波和输入约束情况下控制指令的滞后问题,设计了辅助补偿器对控制指令进行补偿.根据Lyapunov稳定性理论证明了该控制方法能够保证姿态跟踪误差收敛至有界,仿真表明存在复合干扰和输入约束时该方法具有良好的姿态跟踪性能.     

Robust Fault‐Tolerant Control of Launch Vehicle Via GPI Observer and Integral Sliding Mode Control

A robust fault‐tolerant attitude control scheme is proposed for a launch vehicle (LV) in the presence of unknown external disturbances, mismodeling dynamics, actuator faults, and actuator's constraints. The input‐output representation is employed to describe the rotational dynamics of LV rendering three independently decoupled second order single‐input‐single‐output (SISO) systems. In the differential algebraic framework, general proportional integral (GPI) observers are used for the estimations of the states and of the generalized disturbances, which include internal perturbations, external disturbances, and unknown actuator failures. In order to avoid the defects of the conventional sliding surface, a new nonlinear integral sliding manifold is introduced for the robust fault‐tolerant sliding mode controller design. The stability of the GPI observer and that of the closed‐loop system are guaranteed by Lyapunov's indirect and direct methods, respectively. The convincing numerical simulation results demonstrate the proposed control scheme is with high attitude tracking performance in the presence of various disturbances, actuator faults, and actuator constraints.     

Robust attitude tracking control for a rigid spacecraft under input delays and actuator errors

Attitude control of a rigid spacecraft under input delays, disturbances, parameter uncertainties, actuator errors, and constraints is a challenging problem. In this paper, these problems are considered simultaneously, and a robust control approach to attitude tracking of a rigid spacecraft is exploited. The design methodology is based on three steps: (1) compensating input delays by using the backstepping technique, (2) design of a disturbance observer for the delayed system by using the super-twisting algorithm to estimate unknown internal and external disturbances, then adding a feedforward compensation law based on the estimated signal to the backstepping controller to attenuate the effects of disturbances, (3) employing a robust least-square scheme to map the specified control command on the redundant actuators in the presence of actuator error, including actuator magnitude deviation and misalignment, with regard to actuator amplitude and rate constraints. The effectiveness of the proposed algorithm is shown by various numerical simulations.     

Reaction wheel fault‐tolerant finite‐time control for spacecraft attitude tracking without unwinding

This article proposes fault‐tolerant finite‐time attitude tracking control of a rigid spacecraft actuated by four reaction wheels without unwinding problem in the presence of external disturbances, uncertain inertia parameter, and actuator faults. First, a novel antiunwinding finite‐time attitude tracking control law is derived with a designed control signal which works within a known actuator‐magnitude constraint using a continuous nonsingular fast terminal sliding mode (NFTSM) concept. Second, a finite‐time disturbance observer (FTDO) is introduced to estimate a lumped disturbance due to external disturbances, uncertain inertia parameter, actuator faults, and input saturation. Third, a composite controller is developed which consists of a feedback control based on the continuous NFTSM method and compensation term based on the FTDO. The global finite‐time stability is proved using Lyapunov stability theory. Moreover, the singularity and unwinding phenomenon are avoided. Simulation results are conducted under actuator constraints in the presence of external disturbances, inertia uncertainty, and actuator faults and results are illustrated to show the effectiveness of the proposed method. In addition, to show the superiority of the proposed control method over the recently reported control methods, comparative analysis is also presented.     

Adaptive fuzzy fault-tolerant attitude control of spacecraft

This paper investigates the attitude control of spacecraft in the presence of unknown mass moment of inertia matrix, external disturbances, actuator failures, and control input constraints. A robust adaptive controller is proposed with the utilization of fuzzy logic and backstepping techniques. The unit quaternion is employed to describe the attitude of spacecraft for global representation without singularities. The system uncertainty is estimated by introducing a fuzzy logic system. The adaptive mechanism has only two parameters to be adapted on-line because the adaptive law of the proposed controller is derived from the norm of the weight matrix. The stability of the closed-loop system is guaranteed by Lyapunov direct approach. Results of numerical simulations state that the proposed controller is successful in achieving high attitude performance in the presence of parametric uncertainties, external disturbances, actuator failures, and control input constraints.     

Guidance Laws With Input Constraints and Actuator Failures

A novel three‐dimensional fault‐tolerant control guidance law is proposed for interception of maneuvering targets in the presence of external disturbances, actuator failures, and control input constraints. The input‐to‐state stability (ISS) method is introduced to design the fault‐tolerant control guidance law to guarantee robust tracking of a maneuvering target. Then, a saturated fault‐tolerant control guidance law is constructed using a modified saturation function to ensure the resulting control signal will never incur input constraints, and the convergence to a small neighborhood of origin is ensured in theory. Simulation results show that the presented approach is effective in achieving a successful interception against target maneuvers, external disturbances, actuator failures, and control input constraints.     

具有输入输出约束的无人直升机预设性能安全跟踪控制

针对无人直升机姿态与高度系统存在未知外部干扰、输入饱和、姿态与高度约束等问题, 本文提出一种具 有输入输出约束的预设性能安全跟踪控制方法. 首先, 针对无人直升机的姿态与高度约束, 通过设计一类边界保护 算法, 构建了新的安全期望跟踪信号. 为了保证系统对于安全期望跟踪信号的跟踪性能, 将预设性能函数与边界保 护算法进行结合, 并对跟踪误差进行转换. 针对系统的输入饱和现象, 使用Sigmoid函数进行逼近; 同时, 针对饱和函 数的逼近误差与未知外部干扰构成的复合干扰, 采用参数自适应方法对其上界进行逼近. 然后, 结合反步控制方法 设计了安全跟踪控制器, 并通过Lyapunov稳定性理论证明了闭环系统所有信号的收敛性, 保证了无人直升机的安全 跟踪性能. 最终, 通过数值仿真验证了所提控制方法的有效性.     

反步自适应滑模变结构的小卫星姿态鲁棒容错控制

针对小卫星在轨运行中存在输入饱和、干扰力矩与执行器故障的姿态跟踪控制问题,提出了一种反步自适应滑模变结构鲁棒容错控制方法。该方法将反步控制和滑模控制相结合,利用自适应算法估计执行器有效因子最小值和干扰上界,避免了对故障的检测与隔离,实现了输入饱和、干扰和故障对系统稳定性影响的抑制。基于Lyapunov方法从理论上证明了闭环系统的稳定性;将该方法用于小卫星的状态跟踪控制,仿真结果表明该控制器能有效处理姿态控制时输入饱和受限的约束,对部分失效和偏差型故障具有较强的容错能力,并具有一定鲁棒性。     

Robust nonlinear MPC without terminal constraint for tracking changing setpoints in the presence of non-additive unknown disturbance

This paper develops a novel robust tracking model predictive control (MPC) without terminal constraint for discrete-time nonlinear systems capable to deal with changing setpoints and unknown non-additive bounded disturbances. The MPC scheme without terminal constraint avoids difficult computations for the terminal region and is thus simpler to design and implement. However, the existence of disturbances and/or sudden changes in a setpoint may lead to feasibility and stability issues in this method. In contrast to previous works that considered changing setpoints and/or additive slowly varying disturbance, the proposed method is able to deal with changing setpoints and non-additive non-slowly varying disturbance. The key idea is the addition of tightened input and state (tracking error) constraints as new constraints to the tracking MPC scheme without terminal constraints based on artificial references. In the proposed method, the optimal tracking error converges asymptotically to the invariant set for tracking, and the perturbed system tracking error remains in a variable size tube around the optimal tracking error. Closed-loop input-to-state stability and recursive feasibility of the optimization problem for any piece-wise constant setpoint and non-additive disturbance are guaranteed by tightening input and state constraints as well as weighting the terminal cost function by an appropriate stabilizing weighting factor. The simulation results of the satellite attitude control system are provided to demonstrate the efficiency of the proposed predictive controller.