锂离子电池正极材料LiNi_1/3Co_1/3Mn_1/3O_2的研究进展

介绍了一种新型的锂离子电池正极材料LiNi1/3Co1／3Mn1／3O2的最新研究状况,描述了材料的晶体及电子结构,以及电化学性能;重点总结了现今国内外制备此材料的几种主要合成方法及研究进展;同时,介绍了不同掺杂元素（Fe、B、Al、Ti）对材料的改性作用。     

Zn掺杂对LiNi_(1/3)Co_(1/3)Mn_(1/3)O_2结构与电化学性能的影响

用溶胶凝胶法制备了Li Ni1/3Co1/3-x Mn1/3Znx O2(x=0,1/24,2/24,4/24)锂离子电池正极材料。由X射线衍射和扫描电镜对其分析结果表明,Zn掺杂不改变Li Ni1/3Co1/3Mn1/3O2的α-Na Fe O2层状结构,当掺杂量达到4/24时,杂相产生。电化学研究表明,当Zn掺杂量为2/24时,Li Ni1/3Co1/3Mn1/3O2首次放电容量由未掺杂的169.2 m Ah·g-1降低为160.1m Ah·g-1,但循环性能明显提高,30次循环后的容量保持率由未掺杂的89.2%升至97%。并且在20、40、60和80 m A·g-1不同的电流密度下继续循环20次后,当再次恢复到20 m A·g-1的电流密度时,放电容量可恢复到150.3 m Ah·g-1。     

LiOH-Li_2CO_3低共熔混合锂盐体系合成LiNi_(1/3)Co_(1/3)Mn_(1/3)O_2

利用低共熔组成的0.24LiCO3-0.76LiOH混合锂盐体系,与钴、镍、锰的球形氢氧化物按1.1:1混合,无需前期球磨,直接经二段控温程序制备出锂离子正极材料LiNi1/3Co1/3Mn1/3O2。X射线衍射分析表明合成的Li(Ni1/3Co1/3Mn1/3)O2结晶度高,具有规整的层状α-NaFeO2结构,扫描电镜显示产物颗粒均匀,振实密度高达2.89g·cm-3,显著高于用单一锂盐制备的同样产品(2.4g·cm-3)。充放电测试表明,材料具有良好的电性能,首次充放电容量为176和166mhA·g-1,循环50次后,材料的电性能没有明显的衰减。     

改性LiNi_(1/3)Co_(1/3)Mn_(1/3)O_2正极材料的合成及其电化学性能

采用固相反应法制备Mg2+掺杂的锂离子电池正极材料LiNil/3Col/3Mnl/3O2,并将Mg2+最佳掺杂量为0.03(摩尔分数)的样品进行CuO复合。通过X射线衍射(XRD)、扫描电镜(SEM)和电池测试系统等手段对制备的LiNil/3Col/3Mnl/3O2样品的结构、形貌及电化学性能进行表征。结果表明:Mg2+掺杂没有改变LiNil/3Col/3Mnl/3O2的层状结构,Mg2+掺杂量为0.03的LiNil/3Col/3Mnl/3-0.03Mg0.03O2材料具有最好的电化学性能和循环性能,在0.2C倍率下,首次放电比容量达158.5 mA·h/g,10次循环后容量保持率为91.2%。添加CuO的LiNil/3Col/3Mnl/3-0.03Mg0.03O2的首次放电容量为167.4 mA·h/g,高电压下达到181.0 mA·h/g;循环10次后,放电比容量为159.4 mA·h/g,容量保持率为95.3%,改性后的放电比容量、循环性能及在高倍率和高电压下的性能均得到改善。     

锂离子电池正极材料LiNi_(0.5)Co_(0.5)O_2制备与电化学性能

采用球磨湿混和旋转合成相结合的新工艺制备了锂离子电池正极材料 L i Ni0 .5Co0 .5O2 ,并对材料进行了粒度、化学成分以及电化学性能测试。球磨湿混工艺能将原料混合均匀 ,并能有效地使粒度细化。旋转合成工艺能使混合料在均匀的温度场中进行反应 ,并使反应产物粒度均匀和成分均匀。制备的 L i Ni0 .5Co0 .5O2 为单一的 α- Na Fe O2 层状结构 ,粉末粒度分布范围窄 ,平均粒径约为 8μm～ 10μm。电化学性能测试结果表明 ,在 0 .2 m A/cm2 充放电流密度和 3 .0 V～ 4 .2 V电压范围内 ,首次充电容量为 173 m Ah/g,放电容量为 14 8m Ah/g。循环次数达 3 0次时 ,放电容量还有 12 9m Ah/g,循环稳定性良好。球磨湿混和旋转合成相结合的固相合成新工艺能制备出电化学性能良好的L i Ni0 .5Co0 .5O2 正极材料。     

低冰镍衍生的具有高结构稳定性和快速扩散动力学的钠离子掺杂层状LiNi1/3Co1/3Mn1/3O2正极(英文)

通过共沉淀法合成钠离子(Na⁺)掺杂的高稳定性Li_1-xNa_xNi_1/3Co_1/3Mn_1/3O₂(NCM-Na)正极材料。首先论证采用低冰镍提取镍作为合成材料镍源的可行性。其次,在化学试剂合成的NCM(Ni,Co,Mn)材料中预先引入最优含量的Na⁺,占据部分Li⁺位点,实现具有更低Li⁺/Ni²⁺阳离子混排的稳定结构,从而提高其电化学性能。结果表明,当Na⁺掺杂量为1%(质量分数)(x=0.01)时,获得的NCM-Na正极材料在1C电流密度下,循环100次后容量保持率从76.84%提高至89.21%。特别是在5C大电流密度下,循环200次后,可逆放电比容量依然维持在110 mA·h·g^-1。这为杂原子掺杂耦合材料化冶金开发低成本、高性能锂离子电池三元LiNi_1/3Co_1/...     

快速共沉淀过程pH值对Ni_(0.8)Co_(0.1)Mn_(0.1)(OH)_2及LiNi_(0.8)Co_(0.1)Mn_(0.1)O_2性能的影响

采用快速共沉淀法制备Ni0.8Co0.1Mn0.1(OH)2前驱体,利用前驱体与LiOH.H2O的高温固相反应得到锂离子电池层状正极材料LiNi0.8Co0.1Mn0.1O2,探讨pH值对材料结构和电化学性能的影响。通过X射线衍射(XRD)、扫描电镜(SEM)和电化学测试对合成样品进行表征。结果表明,pH值为11.00~12.00时,合成的Ni0.8Co0.1Mn0.1(OH)2前驱体均无杂相;pH值为11.50时,合成的前驱体制备出的正极材料具有良好的电化学性能,0.1C倍率下首次放电比容量为192.4 mA.h/g;经过40次循环,容量保持率为91.56%。     

锂离子电池正极材料LiNi1/3Co1/3Mn1/3O2的制备及性能研究

采用溶胶-凝胶法制备了锂离子电池正极材料LiNi1/3Co1/3Mn1/3O2,并考察了烧结温度对材料结构、表面形貌和电化学性能的影响.XRD和SEM测试结果表明,900℃下烧结得到的样品是粒径在0.3～0.5 μm范围的球形粒子,具有最佳的阳离子有序度;充放电测试结果表明,其在0.1C倍率下首次放电容量达到148.8...     

F~-掺杂LiNi_(0.5)Mn_(1.5)O_4材料的制备及性能研究

为改善LiNi_(0.5)Mn_(1.5)O_4的倍率性能和循环性能,采用二步固相法制备了F-掺杂的LiNi_(0.5)Mn_(1.5)O_(4-x)F_x(x=0,0.05,0.1,015,0.2)正极材料,讨论了不同F掺杂量对材料性能的影响。X射线衍射、扫描电镜结果表明,掺杂和未掺杂的正极材料都为单一的尖晶石结构,粒度分布均匀。充放电测试、循环伏安和交流阻抗测试结果表明:当F的掺杂量为x=0.1时(LiNi_(0.5)Mn_(1.5)O_(3.9)F_(0.1))正极材料的性能最好,0.1,0.5,1,2及5C倍率的首次放电比容量依次为129.07,123.59,118.49,114.49和92.57 mAh/g。1C倍率下循环30次,容量保持率仍为98.84%。     

Si4+和F-掺杂对LiNi1/3Co1/3Mn1/3O2结构和电化学性能的影响

以Li2CO3、NiO、Co2O3、MnO2、LiF和SiO2为原料,采用机械力活化固相法制备了Si4+和F-掺杂的锂离子电池正极材料LiNi1/3Co 1/3Mn1/3O2.通过X射线衍射(XRD)、扫描电镜(SEM)和电化学性能测试等技术研究了LiNi1/3Co1/3Mn1/3O2的结构特征、形貌及电化学性能等.结...     

Preparation of LiNi1/3Co1/3Mn1/3O2 cathode materials from spent Li-ion batteries

A recycling process including separation of electrode materials by ultrasonic treatment, acid leaching, Fe-removing, precipitation of cobalt, nickel, manganese and lithium has been applied successfully to recycle spent lithium-ion batteries and to synthesize LiNi1/3Co1/3Mn1/3O2. When ultrasonic treatment with 2-nitroso-4-methylphenol（NMP） at 40 ℃ for 15 min, the electrode materials are separated completely. Above 99% of Co, Ni, Mn and Li, 95% of Fe in the separated electrodes are acid-leached in the optimized conditions of 2 mol/L H2SO4, 1：2 H2O2：H2SO4 （molar ratio）, 70 ℃, 1：10 initial S：L ratio, and l h. 99.5% of Fe and less than 1% of Co, Ni, Mn in the leaching solution can be removed in the conditions of initial pH value 2.0-2.5 adjusted by adding 18% Na2CO3, 90 ℃ and stirring time 3 h. After adjusted to be equal by adding NiSO4, COSO4 and MnSO4 solution, 97.1% of Ni, Co, Mn in the Fe-removing surplus leaching solution can be recovered as Ni1/3Co1/3Mn1/3（OH）2. 94.5% of Li in the surplus filtrate after the deposition of Co, Ni and Mn can be recovered as LiECO3. The LiNi1/3Co1/3Mnl/3O2, prepared from the recovered compounds, is found to have good characteristics of the layered structure and elecrtochemical performance.     

LiNi1/3Co1/3Mn1/3O2和LiNi3/8Co1/4Mn3/8O2纳米纤维的合成与电化学性能

以溶胶前驱体为纺丝液,通过静电纺丝法合成锂离子电池正极材料LiNi1/3Co1/3Mn1/3O2和LiNi3/8Co1/4Mn3/8O2纳米纤维.采用原子力显微镜(AFM)、X射线衍射(XRD)、充放电实验对纳米纤维的形貌、结构和电化学性能进行研究.结果表明,纳米纤维的直径在150～200 nm之间,且具有典型的α-NaFeO2层状结构.LiNi1/3Co1/3Mn1/3O2和LiNi3/8Co1/4Mn3/8O2纳米纤维的首次放电容量均超过170 mAh·g-1,50次循环后容量保持率在90%以上.     

Surface composition and electrochemical behavior of LiNi1/3Co1/3Mn1/3O2 cathode material with copper additive

LiNi_1/3Co_1/3Mn_1/3O₂（NCM） cathode material containing copper was prepared by co-precipitation method.The material was characterized by X-ray photoelectron spectroscopy（XPS） and galvanostatic cycling.XPS data indicate that surface compositions of the samples containing copper are different from the bare NCM.Copper on surface of particles was enriched,while nickel and lithium content was reduced.The electrochemical performance of NCM was affected by the change of surface compositions.Cycling performance charged to the cutoff voltage of 4.6 V was improved by introducing copper into the material.The effects of copper content on electrochemical behaviors of NCM at 4.5 V were discussed.     

Synthesis and electrochemical performances of LiNi0.6Co0.2Mn0.2O2 cathode materials

LiNi_0.6Co_0.2Mn_0.2O₂ was prepared from LiOH·H₂O and MCO₃ (M=Ni, Co, Mn) by co-precipitation and subsequent heating. XRD, SEM and electrochemical measurements were used to examine the structure, morphology and electrochemical characteristics, respectively. LiNi_0.6Co_0.2Mn_0.2O₂ samples show excellent electrochemical performances. The optimum sintering temperature and sintering time are 850 °C and 20 h, respectively. The LiNi_0.6Co_0.2Mn_0.2O₂ shows the discharge capacity of 148 mA·h/g in the range of 3.0?4.3 V at the first cycle, and the discharge capacity remains 136 mA·h/g after 30 cycles. The carbonate co-precipitation method is suitable for the preparation of LiNi_0.6Co_0.2Mn_0.2O₂ cathode materials with good electrochemical performance for lithium ion batteries.     

Synthesis and characterization of layered Li（Ni1/3Mn1/3CO1/3）O2 cathode materials by spray-drying method

Spherical Li(Ni_(1/3)Mn_(1/3)Co_(1/3))O_2 was prepared via the homogenous precursors produced by solution spray-drying method. The precursors were sintered at different temperatures between 600 and 1 000 ℃ for 10 h. The impacts of different sintering temperatures on the structure and electrochemical performances of Li(Ni_(1/3)Mn_(1/3)Co_(1/3))O_2 were compared by means of X-ray diffractometry(XRD), scanning electron microscopy(SEM), and charge/discharge test as cathode materials for lithium ion batteries. The experimental results show that the spherical morphology of the spray-dried powers maintains during the subsequent heat treatment and the specific capacity increases with rising sintering temperature. When the sintering temperature rises up to 900 ℃ , Li(Ni_(1/3)Mn_(1/3)Co_(1/3))O_2 attains a reversible capacity of 153 mA·h/g between 3.00 and 4.35 V at 0.2C rate with excellent cyclability.     

层状LixNi1/3Mn1/3Co1/3O2阴极材料的结构、电化学与热稳定性

用NO2BF4作为脱锂剂,通过化学反应定量脱去材料中的锂离子,合成出不同嵌锂量的LixNi1/3Mn1/3-Co1/3O2(0≤x≤1)系列材料.通过电感耦合等离子体质谱(ICP-MS)、光电子能谱(XPS)、X射线衍射(XRD)、循环伏安(CV)等方法表征手段发现,当锂脱出量超过总量的49%后,材料的结构、过渡金属的价态、电化学性能等方面都发生显著变化,这些变化中的不可逆因素影响了其首次充放过程的可逆性.结合TPD-MS以及TG分析,结果表明,在脱锂过程中晶格氧的活性增强,更加容易在较低温度下脱出,影响了材料的热稳定性.     

Effects of synthesis conditions on the structural and electrochemical properties of layered LiNi1/3Co1/3Mn1/3O2 cathode material via oxalate co-precipitation method

The uniform layered LiNi1/3Co1/3Mn1/3O2 cathode material for lithium ion batteries was prepared by using (Ni1/3Co1/3Mn1/3)C2O4 as precursor synthesized via oxalate co-precipitation method in air. The effects of calcination temperature and time on the structure and electrochemical properties of the LiNi1/3Co1/3Mn1/3O2 were systemically studied. XRD results revealed that the optimal calcination conditions to prepare the layered LiNi1/3Co1/3Mn1/3O2 were 950°C for 15 h. Electrochemical measurement showed that the sample prepared under the such conditions has the highest initial discharge capacity of 160.8 mAh/g and the smallest irreversible capacity loss of 13.5% as well as stable cycling performance at a constant current density of 30 mA/g between 2.5 and 4.3 V versus Li at room temperature.     

LiNi0.7Co0.15Mn0.15O2 microspheres as high-performance cathode materials for lithium-ion batteries

Advanced uniform LiNi0.7Co0.15Mn0.15O2 microspheres were successfully synthesized and examined as cathode materials for lithium-ion batteries. The structure,morphology, and electrochemical performance of LiNi0.7-Co0.15Mn0.15O2 calcined at different temperatures ranging from 650 to 900 °C were systematically investigated. The XRD results show that the material has a well-ordered layered structure with small amount of cation mixing. A distinct spherical morphology of the obtained powders prepared at different temperatures can be seen from the SEM images. The as-synthesized LiNi0.7Co0.15Mn0.15O2 powders have a very high-tap density of about 2.37 g·cm^-3. Among all the samples,the sample calcined at 750 °C exhibits the best electrochemical performance with an initial discharge capacity of185.2 mAh·g^-1（3.0–4.3 V, 0.2C rate） and capacity retention〉94.77 %after50cycles.Moreover,thismaterialshowshighspecific capacity and good cycling stability. The LiNi0.7-Co0.15Mn0.15O2 microspheres with high-specific capacity and high-tap density are promising to use as cathode materials for next-generation high-energy-density lithium-ion batteries.     

Synthesis of LiNi1/3CO1/3Mn1/3O2 cathode material via oxalate precursor

Using oxalic acid and stoichiometrically mixed solution of NiCl2, CoCl2, and MnCl2 as starting materials, the triple oxalate precursor of nickel, cobalt, and manganese was synthesized by liquid-phase co-precipitation method. And then the LiNi1/3Co1/3Mn1/3O2 cathode materials for Li-ion battery were prepared from the precursor and LiOH-H2O by solid-state reaction. The precursor and LiNi1/3Co1/3Mn1/3O2 were characterized by chemical analysis, XRD, EDX, SEM and TG-DTA. The results show that the composition of precursor is Ni1/3Co1/3Mn1/3C2O4·2H2O. The product LiNi1/3Co1/3Mn1/3O2, in which nickel, cobalt and manganese are uniformly distributed, is well crystallized with a-NaFeO2 layered structure. Sintering temperature has a remarkable influence on the electrochemical performance of obtained samples. LiNi1/3Co1/3Mn1/3O2 synthesized at 900 ℃ has the best electrochemical properties. At 0.1C rate, its first specific discharge capacity is 159.7 mA·h/g in the voltage range of 2.75-4.30 V and 196.9 mA·h/g in the voltage range of 2.75-4.50 V; at 2C rate, its specific discharge capacity is 121.8 mA·h/g and still 119.7 mA·h/g after 40 cycles. The capacity retention ratio is 98.27%.     

球形LiNi1/3Co1/3Mn1/3O2的合成及其电化学性能

以化学共沉淀法制备的球形Ni1/3Co1/3Mn1/3CO3为前驱体合成了球形LiNi1/3Co1/3Mn1/3O2,研究LiNi1/3Co1/3Mn1/3O2合成工艺对产物形貌的影响.结果表明直接以前驱体Ni1/3Co1/3Mn1/3CO3与Li2CO3反应合成的LiNi1/3Co1/3Mn1/3O2的一次颗粒较大,以前驱体分解后的氧化物与Li2CO3反应合成的LiNi1/3Co1/3Mn1/3O2的一次颗粒相对细小;合成的LiNi1/3Co1/3Mn1/3O2均为具有层状结构的纯相物质;球形正极材料LiNi1/3Co1/3Mn1/3O2充放电过程中存在一个材料活化的过程,在前10周期充放电时,电池容量处于增加的状态;在2.7～4.3 V的电压范围内1 C倍率下电池的放电比容量达到149 mA·h/g,0.2 C倍率下为158 mA·h/g,经50次循环后容量无衰减.