Catalytic reduction of NH4NO3 by NO: Effects of solid acids and implications for low temperature DeNOx processes

Ammonium nitrate is thermally stable below 250 °C and could potentially deactivate low temperature NO_x reduction catalysts by blocking active sites. It is shown that NO reduces neat NH₄NO₃ above its 170 °C melting point, while acidic solids catalyze this reaction even at temperatures below 100 °C. NO₂, a product of the reduction, can dimerize and then dissociate in molten NH₄NO₃ to NO⁺ + NO₃⁻, and may be stabilized within the melt as either an adduct or as HNO₂ formed from the hydrolysis of NO⁺ or N₂O₄. The other product of reduction, NH₄NO₂, readily decomposes at ≤100 °C to N₂ and H₂O, the desired end products of DeNO_x catalysis. A mechanism for the acid catalyzed reduction of NH₄NO₃ by NO is proposed, with HNO₃ as an intermediate. These findings indicate that the use of acidic catalysts or promoters in DeNO_x systems could help mitigate catalyst deactivation at low operating temperatures (<150 °C).     

Application of NOX storage/release materials based on alkali-earth oxides supported on Al2O3 for high-temperature diesel soot oxidation

Alkali-earth oxides and nitrates supported on alumina were studied as model systems for NO_X storage/release. Their impact on the high-temperature soot oxidation has been investigated. The stability of surface nitrates and temperature of NO_X release increase parallel to the basicity of the cation. The presence of soot decreases the temperature of NO_X release. The storage capacity depends on the several factors, such as basicity, dispersion of the cation, and pre-treating conditions. Adsorption of NO with O₂ at 200 °C leads to the formation of surface nitrates that mainly exist as ionic nitrates. Stored nitrates contribute to the soot oxidation and assist to lower the temperature of soot oxidation up to almost 100 °C. In the presence of only NO_X storage material the efficiency of NO_X utilization is, however, quite low, around 30%. Therefore, the presence of an oxidation catalyst is essential to increase the efficiency of NO_X utilization for soot oxidation up to 140% and selectivity towards CO₂. A combination of oxidation catalyst with NO_X storage materials enables to lower the temperature of soot oxidation more than 100 °C for the Sr- and Ca-based systems.     

Dynamics and selectivity of NOx reduction in NOx storage catalytic monolith

Several nitrogen compounds can be produced during the regeneration phase in periodically operated NO_x storage and reduction catalyst (NSRC) for conversion of automobile exhaust gases. Besides the main product N₂, also NO, N₂O, and NH₃ can be formed, depending on the regeneration phase length, temperature, and gas composition. This contribution focuses on experimental evaluation of the NO_x reduction dynamics and selectivity towards the main products (NO, N₂ and NH₃) within the short rich phase, and consequent development of the corresponding global reaction-kinetic model. An industrial NSRC monolith sample of PtRh/Ba/CeO₂/ -Al₂O₃ type is employed in nearly isothermal laboratory micro-reactor. The oxygen and NO_x storage/reduction experiments are performed in the temperature range 100–500 °C in the presence of CO₂ and H₂O, using H₂, CO and C₃H₆ as the reducing agents.The spatially distributed NSRC model developed earlier is extended by the following reactions: NH₃ is formed by the reaction of H₂ with NO_x and it can further react with oxygen and NO_x deposited on the catalyst surface, producing N₂. Considering this scheme with ammonia as an active intermediate of the NO_x reduction, a good agreement with experiments is obtained in terms of the NO_x reduction dynamics and selectivity. A reduction front travelling in the flow direction along the reactor is predicted, with the NH₃ maximum on the moving boundary. When the front reaches the reactor outlet, the NH₃ peak is observed in the exhaust gas. It is assumed that the ammonia formation during the NO_x reduction by CO and HCs at higher temperatures proceed via the water gas shift and steam reforming reactions producing hydrogen. It is further demonstrated that oxygen storage effects influence the dynamics of the stored NO_x reduction. The temperature dependences of the outlet ammonia peak delay and the selectivity towards NH₃ are correlated with the effective oxygen and NO_x storage capacity.     

Influence of the Type of Reducing Agent (H2, CO, C3H6 and C3H8) on the Reduction of Stored NOX in a Pt/BaO/Al2O3 Model Catalyst

In this investigation, a comparative study for a NO _X storage catalytic system was performed focusing on the parameters that affect the reduction by using different reductants (H₂, CO, C₃H₆ and C₃H₈) and different temperatures (350, 250 and 150 °C), for a Pt/BaO/Al₂O₃ catalyst. Transient experiments show that H₂ and CO are highly efficient reductants compared to C₃H₆ which is somewhat less efficient. H₂ shows a significant reduction effect at relatively low temperature (150 °C) but with a low storage capacity. We find that C₃H₈does not show any NO _X reduction ability for NO _X stored in Pt/BaO/Al₂O₃ at any of the temperatures. The formation of ammonia and nitrous oxide is also discussed.     

Steam resistant CoLa-mordenite catalysts for the SCR of NOx with CH4

The stabilization of Co-mordenite catalysts through lanthanum exchange is reported here. The effect of exchange order and calcination conditions upon the reduction of NO_x to N₂ at 500 °C was tracked during 400 h on a stream containing NO_x, CH₄, O₂ and 10% H₂O. Both the fresh and used catalysts were characterized through TPR, Raman spectroscopy, FTIR spectroscopy using CO as probe molecule, and XPS. These techniques revealed that the CoLa-mordenite catalysts which were not affected by the severe hydrothermal treatment showed no sign of Co or La migration out of the exchange positions. Instead, those that rapidly deactivated showed the formation of cobalt oxides and, in some cases, the migration of the cations to other exchange positions. The presence of exchanged lanthanum seems to preserve the integrity of the zeolite structure preventing the migration of cobalt ions with the subsequent formation of cobalt oxides which favors the reaction of methane with O₂, thus decreasing N₂ production.     

Reduction of NO2 stored in a commercial lean NO x trap at low temperatures

Isothermal storage of NO₂ and subsequent reduction with different reducing agents (H₂, CO or H₂ + CO) in a lean NO _x trap catalyst was tested by Temperature Programmed Desorption (TPD) and Temperature Programmed Reduction (TPR) experiments at temperatures representative of automotive “cold-start” conditions (<200 °C) using a commercial NO _x trap catalyst. Results from the TPR experiments revealed that no reduction of stored NO₂ to N₂ was observed at 100–180 °C, and at 200 °C 10% reduction only of NO₂ to N₂ was measured. A special affinity of H₂ to form NH₃ was observed during the reduction of stored NO₂. The formation of NH₃ increases with increasing amount of stored NO₂ and decreases with increasing storage temperature. Direct relation exists between the amount of adsorbed and/or stored NO₂ and the formation of H₂O and NH₃.     

Methanol interaction with NO2: An attempt to identify intermediate compounds in CH4-SCR of NO with Co/Pd-HFER catalyst

The objective of this work is the study of fundamental common aspects of NO_x catalytic reduction over a Co/Pd-HFER zeolite catalyst, using methanol or methane as reducing agent. Temperature Programmed Surface Reaction (TPSR) studies were performed with reactant mixtures comprising NO₂ and one of the reducing agents.The formation of formaldehyde was detected in both studied reactions (NO₂–CH₄ and NO₂–CH₃OH) in the temperature range between 100 and 220 °C. At higher temperature, when the NO_x reduction process effectively begins, formaldehyde starts to be consumed.Using methanol as reducing agent, nitromethane and nitrosomethane, are detected. At 300 °C these species are consumed and cyanides and iso-cyanides formation occurs. On the contrary, with methane, these last species were not detected; however, there are strong evidences for CH₃NO and CH₃NO₂ formation.Thus, using methanol or methane, similar phenomena were detected. In both cases, common intermediary species seem to play an important role in the NO_x reduction process to N₂.These results suggest that methanol can be considered as a reaction intermediate species in the mechanism of the reduction of NO₂ with methane, over cobalt/palladium-based ferrierite catalysts.     

NOx storage behavior and sulfur-resisting performance of the third-generation NSR catalysts Pt/K/TiO2–ZrO2

The NO_x storage and reduction (NSR) catalysts Pt/K/TiO₂–ZrO₂ were prepared by an impregnation method. The techniques of XRD, NH₃-TPD, CO₂-TPD, H₂-TPR and in situDRIFTS were employed to investigate their NO_x storage behavior and sulfur-resisting performance. It is revealed that the storage capacity and sulfur-resisting ability of these catalysts depend strongly on the calcination temperature of the support. The catalyst with theist support calcined at 500 °C, exhibits the largest specific surface area but the lowest storage capacity. With increasing calcination temperature, the NO_x storage capacity of the catalyst improves greatly, but the sulfur-resisting ability of the catalyst decreases. In situ DRIFTS results show that free nitrate species and bulk sulfates are the main storage and sulfation species, respectively, for all the catalysts studied. The CO₂-TPD results indicate that the decomposition performance of K₂CO₃ is largely determined by the surface property of the TiO₂–ZrO₂ support. The interaction between the surface hydroxyl of the support and K₂CO₃ promotes the decomposition of K₂CO₃ to form –OK groups bound to the support, leading to low NO_x storage capacity but high sulfur-resisting ability, while the interaction between the highly dispersed K₂CO₃ species and Lewis acid sites gives rise to high NO_x storage capacity but decreased sulfur-resisting ability. The optimal calcination temperature of TiO₂–ZrO₂ support is 650 °C.     

Excellent sulfur resistance of Pt/BaO/CeO2 lean NOx trap catalysts

In this work, we investigated the NO_x storage behavior of Pt/BaO/CeO₂ catalysts, especially in the presence of SO₂. High surface area CeO₂ (110 m²/g) with a rod like morphology was synthesized and used as a support. The Pt/BaO/CeO₂ sample demonstrated slightly higher NO_x uptake in the entire temperature range studied compared with Pt/BaO/γ-Al₂O₃. More importantly, this ceria-based catalyst showed higher sulfur tolerance than the alumina-based one. The time of complete NO_x uptake was maintained even after exposing the sample to 3 g/L of SO₂. The same sulfur exposure, on the other hand, eliminated the complete NO_x uptake time on the alumina-based NO_x storage catalysts. TEM images show no evidence of either Pt sintering or BaS phase formation during reductive de-sulfation up to 600 °C on the ceria-based catalyst, while the same process over the alumina-based catalyst resulted in both a significant increase in the average Pt cluster size and the agglomeration of a newly formed BaS phase into large crystallites. XPS results revealed the presence of about five times more residual sulfur after reductive de-sulfation at 600 °C on the alumina-based catalysts in comparison with the ceria-based ones. All of these results strongly support that, besides their superior intrinsic NO_x uptake properties, ceria-based catalysts have (a) much higher sulfur tolerance and (b) excellent resistance against Pt sintering when they are compared to the widely used alumina-based catalysts.     

Novel promoting effect of SO2 on the selective catalytic reduction of NOx by ammonia over Co3O4 catalyst

Spinel nano-Co₃O₄ was prepared by solid-state reaction at room temperature and investigated for selective catalytic reduction of NO_x by NH₃ (NH₃-SCR). Although suffering from pore filling and plugging, treatment of this catalyst by SO₂ showed novel promoting effect on NH₃-SCR above 250 °C. Bulk cobalt sulfate was observed over the sulfated Co₃O₄ with XRD, which would be an active component for NH₃-SCR. The sulphated Co₃O₄ catalyst exhibited good resistance to SO₂ (500 ppm, 100 ppm) and 10% H₂O at a space velocity of about 25 000 h⁻¹ at 300 °C, as tested for 12 h.     

NOx adsorption and diesel soot combustion over La2O3 supported catalysts containing K, Rh and Pt

In this work we report results of NOx adsorption and diesel soot combustion on a noble metal promoted K/La₂O₃ catalyst. The fresh-unpromoted solid is a complex mixture of hydroxide and carbonate compounds, but the addition of Rh favors the preferential formation of lanthanum oxycarbonate during the calcination step. K/La₂O₃ adsorbs NOx through the formation of La and K nitrate species when the solid is treated in NO + O₂ between 70 and 490 °C. Nitrates are stable in the same temperature range under helium flow. However, they become unstable at ca. 360 °C when either Rh and/or Pt are present, the effect of Rh being more pronounced. Nitrates decompose under different atmospheres: NO + O₂, He and H₂. The effect of Rh might be to form a thermally unstable complex (Rh–NO⁺) which takes part both in the formation of the nitrates when the catalyst is exposed to NOx and in the nitrates decomposition at higher temperatures. Regarding soot combustion, nitrates react with soot with a temperature of maximun reaction rate of ca. 370 °C, under tight contact conditions. This temperature is not affected by the presence of Rh, which indicates that the stability of nitrates has little effect on their reaction with soot.     

Kinetic modeling of storage and reduction with different reducing agents (CO, H2, and C2 H4) on a Pt–Ba/-Al2O3 catalyst in the presence of CO2 and H2O

In this paper a global reaction kinetic model is used to understand and describe the NO_x storage/reduction process in the presence of CO₂ and H₂O. Experiments have been performed in a packed bed reactor with a Pt–Ba/γ-Al₂O₃ powder catalyst (1 wt% Pt and 30 wt% Ba) with different lean/rich cycle timings at different temperatures (200, 250, and ) and using different reductants (H₂, CO, and C₂H₄). Model simulations and experimental results are compared. H₂O inhibits the NO oxidation capability of the catalyst and no NO₂ formation is observed. The rate of NO storage increases with temperature. The reduction of stored NO with H₂ is complete for all investigated temperatures. At temperatures above , the water gas shift (WGS) reaction takes place and H₂ acts as reductant instead of CO. At , CO and C₂H₄ are not able to completely regenerate the catalyst. At the higher temperatures, C₂H₄ is capable of reducing all the stored NO, although C₂H₄ poisons the Pt sites by carbon decomposition at . The model adequately describes the NO breakthrough profile during 100 min lean exposure as well as the subsequent release and reduction of the stored NO. Further, the model is capable of simulating transient reactor experiments with 240 s lean and 60 s rich cycle timings.     

Selective catalytic reduction of NOX with ammonia over Mn-Ce-OX/TiO2-carbon nanotube composites

Mn-Ce-O_X catalysts loaded on TiO₂-carbonaceous materials were prepared by sol-gel method. Selective catalytic reduction of NO_X was conducted in a fixed-bed flow-reactor over catalysts coated on aluminum plates. A de-NO_X efficiency of more than 90% was obtained over the Mn-Ce-O_X/TiO₂-carbon nanotubes (CNTs) catalyst between 75 °C and 225 °C under a gas hourly space velocity (GHSV) of ~ 36,000 h⁻¹. This activity improvement is attributed to the increase of the BET surface area, and the occurrence of reaction between adsorbed NO_X and NH₃. Moreover, the de-NO_X efficiency was increased to 99.6% by adding 250 ppm SO₂ between 100 °C and 250 °C.     

NO decomposition and reduction on Pt/Al2O3 powder and monolith catalysts using the TAP reactor

A systematic study over Pt/Al₂O₃ powder and monolith catalysts is carried out using temporal analysis of products (TAP) to elucidate the transient kinetics of NO decomposition and NO reduction with H₂. NO pulsing and NO–H₂ pump-probe experiments demonstrate the effect of catalyst temperature, NO–H₂ pulse delay time and H₂/NO ratio on N₂, N₂O and NH₃ selectivity. At lower temperature (150 °C) decomposition of NO is negligible in the absence of H₂, indicating that N–O bond scission is rate limiting. At higher temperature NO decomposition occurs readily on reduced Pt but the rate is inhibited by surface oxygen as reaction occurs. The reduction of NO by a limiting amount of H₂ at lower temperature indicates the reaction of surface NO with H adatoms to form N adatoms, which react with adsorbed NO to form N₂O or recombine to form N₂. In excess H₂, higher temperatures and longer delay times favor the production of N₂. The longer delay enables NO decomposition on reduced Pt with the role of H₂ being a scavenger of surface oxygen. Lower temperatures and shorter delay times are favorable for ammonia production. The sensitive dependence on delay time indicates that the fate of adsorbed NO depends on the concentration of vacant sites for NO bond scission, necessary for N₂ formation, and of surface hydrogen, necessary for hydrogenation to ammonia. A mechanistic-based microkinetic model is proposed that accounts for the experimental observations. The TAP experiments with the monolith catalyst show an improved signal due to the reduction of transport restrictions caused by the powder. The improved signal holds promise for quantitative TAP studies for kinetic parameters estimation and model discrimination.     

Enhancement of oxygen storage capacity by reductive treatment of Al2O3 and CeO2–ZrO2 solid solution nanocomposite

Oxygen storage capacity (OSC) of CeO₂–ZrO₂ solid solution, Ce_xZr_(1−x)O₄, is one of the most contributing factors to control the performance of an automotive catalyst. To improve the OSC, heat treatments were employed on a nanoscaled composite of Al₂O₃ and CeZrO₄ (ACZ). Reductive treatments from 700 to 1000 °C significantly improved the complete oxygen storage capacity (OSC-c) of ACZ. In particular, the OSC-c measured at 300 °C reached the theoretical maximum with a sufficient specific surface area (SSA) (35 m²/g) after reductive treatment at 1000 °C. The introduced Al₂O₃ facilitated the regular rearrangement of Ce and Zr ions in CeZrO₄ as well as helped in maintaining the sufficient SSA. Reductive treatments also enhanced the oxygen release rate (OSC-r); however, the OSC-r variation against the evaluation temperature and the reduction temperature differed from that of OSC-c. OSC-r measured below 200 °C reached its maximum against the reduction temperature at 800 °C, while those evaluated at 300 °C increased with the reduction temperature in the same manner as OSC-c.     

Transient TPSR, DRIFTS-MS and TGA studies of a Pd/ceria-zirconia catalyst in CH4 and NO2 atmospheres

In this study, the parameters governing the activity of Pd/ceria-zirconia catalysts in the selective catalytic reduction (SCR) of NO_x assisted by methane are investigated using a combination of temperature-programmed spectroscopic and thermogravimetric techniques and transient SCR conditions. By DRIFTS of adsorbed CO, it is established that Pd species on Ce_0.2Zr_0.8O₂ are mainly present in cationic form but exhibit high reducibility. As found by temperature-programmed surface reaction (TPSR) in CH₄ + NO₂ atmosphere, the CH₄-SCR reaction is initiated at 280 °C on Pd/Ce_0.2Zr_0.8O₂ and yields almost 100% N₂ above 500 °C. DRIFTS-MS and TGA experiments performed under transient SCR conditions show that DeNO_x activity is due to a surface reaction between some methane oxidation products on reduced Pd sites with ad-N_xO_y species presumably located on the support. The detrimental effect of O₂ on DeNO_x is explained by the promotion of the total combustion of methane assisted by the ceria-zirconia component at the expense of the SCR reaction above 320 °C.     

Reduction of NOx Stored at Low Temperatures on a NOx Adsorbing Catalyst

Isothermal storage and reduction of NO₂ with CO, C₃H₆ and H₂ as reducing agents on a lean NO _x adsorber was investigated by temperature programmed desorption (TPD) and temperature programmed reduction (TPR) studies. The reduction of NO _x was clearly favoured with H₂ as reducing agent. Carbon monoxide and C₃H₆ showed fairly low reduction of NO _x . The NO _x reduction at low temperatures with H₂ as reducing agent was found to be effective, clearly much more effective than for CO.     

NO2 and N2 sorption in MFI films with varying Si/Al and Na/Al ratios

MFI crystals or films with controlled thicknesses and different Si/Al ratios were grown on seeded cordierite monoliths using a clear synthesis mixture with template or a template-free gel. The materials were analyzed by scanning electron microscopy, X-ray diffraction, inductively coupled plasma-atomic emission spectrometry, X-ray photoelectron spectroscopy, thermogravimetric analysis and sorption experiments using N₂ or NO₂ adsorbates. The films were uniformly distributed over the support surface. As expected, the specific monolayer N₂ adsorption capacity (mol/g_zeolite) was constant and independent of film thickness. The specific molar NO₂ adsorption capacity was significantly lower than the specific molar monolayer N₂ adsorption capacity, indicating that NO₂ is adsorbed at specific sites rather than evenly distributed in a monolayer. A number of NO₂ adsorption sites with varying strengths were observed by TPD experiments. At 30 °C, the amount of adsorbed NO₂ in the MFI films increased with increasing Al and Na content as opposed to the N₂ adsorption capacity, which was independent of these parameters. At 200 °C, the adsorbed amount of NO₂ was lower than at 30 °C and apparently independent on Al concentration in the Na-MFI films. These results indicate that different mechanisms are involved in NO₂ adsorption. NO₂ may adsorb weakly on Na⁺ cations and also react with silanol groups and residual water in the zeolite, the latter two results in more strongly bound species. Upon NO₂ adsorption, formation of NO was observed. This work represents the first systematic study of the effects of Al and Na content on NO₂ adsorption in MFI films.     

Effect of pretreatment and regeneration conditions of Ru/γ-Al2O3 catalysts for N2O decomposition and/or reduction in O2-rich atmospheres and in the presence of NOX, SO2 and H2O

The effect of the pretreatment (inert, oxidative, and reducing) of Ru/γ-Al₂O₃ catalyst on its activity and stability in the decomposition of N₂O in the absence or presence of O₂, SO₂, H₂O and NO_X was studied in the present work. Decomposition of pure N₂O was slightly enhanced by the H₂-pretreated catalyst (metallic Ru) compared to the O₂- or He-pretreated ones, owing to a cyclic oxidation–reduction pathway of metallic Ru. The observed decrease of activity by O₂ or H₂O addition was reversible compared to SO₂ which caused a strong, irreversible deactivation of the catalyst, irrespective of the type of pretreatment. This was attributed to the formation of stable sulphates, mainly those on RuO₂ surface, which could only be removed by regeneration under reducing (H₂ in He) atmosphere at temperatures of ca. 500 °C. Oxidative or inert regeneration required very high temperatures (i.e. >700 °C) in order to decompose these sulphates. A method of retaining N₂O conversion activity very high (≥98%) for long reaction times is suggested and is based on frequent and short-time (ca. 10 min) regenerations of the catalyst under reducing atmosphere (ca. 5% H₂ in He). The effect of co-feeding various reducing agents, such as CO or C₃H₆, on the N₂O conversion activity in the presence of O₂, SO₂, H₂O and NO_X is negligible, mainly because they are oxidized at relatively low temperatures in the O₂-rich feeds used in this study.