共查询到20条相似文献,搜索用时 31 毫秒
1.
以DK7725型快走丝线切割机为例,对快走丝线切割机加工中出现的断丝问题,按照加工过程归类分析了断丝原因,并从机床及工艺方面提出了相应的解决措施。 相似文献
2.
由于铝的熔化热和汽化热低,当使用快走丝线切割机加工铝合金时,易产生熔化反应,加工表面粗糙,产生的电蚀物粘附在钼丝上,使导电块早期磨损,并在钼丝与工件间产生非正常火花放电,在导电块表面上切割出细沟槽,引起夹丝、断丝现象。通过改进切割工艺及试验,得到了提高加工稳定性及切割面质量的措施和方法。 相似文献
3.
针对高速走丝线切割机床加工中常见的断丝现象,详细分析了导致电极丝断丝的6大因素,并提出了相应的预防措施和解决办法,减少断丝几率,有效地提高加工精度、加工效率和表面质量. 相似文献
4.
5.
6.
7.
8.
9.
低速走丝线切割加工的断丝分析与处理 总被引:1,自引:1,他引:0
由于低速走丝线切割机是采取电极丝单向连续运行的方式完成加工过程的 ,因此即使电极丝发生损耗 ,也能持续地予以补充 ,保证加工的高精度和持续性。且低速走丝线切割机采用CNC智能控制 ,在一定条件下 ,可以实现无人监控加工 ,不间断生产。但断丝却会成为这些优势的障碍 ,解决此问题也就十分必要。解决断丝 ,就是要很好地控制加工时的放电状态 ,对有直接影响的主要因素 ,如人员、设备、材质等一一考虑 ,分析对待。1 断丝的机床因素控制与改善对于断丝 ,一般的认识是电极丝的抗拉强度太低而引起 ,其实并非完全由于抗拉强度太低 ,电极丝的… 相似文献
10.
11.
12.
13.
14.
15.
16.
17.
18.
With preheating wire by resistance heat, laser hot wire welding improves process stability and wire deposition efficiency, which gives broad potential applications in sugracing and narrow gap welding. It is a critical issue to control the temperature of preheated wire in this process. The temperature which is so high that the wire fuses outside molten pool or so low that the wire cannot melt timely in the molten pool, results in poor wire transfer stability and bad weld formation. This paper is purposed to calculate the wire temperature for the prediction of wire transfer behavior under various welding parameters. A heat conduction model is set up. Heat sources of the wire include resistance heat and reflected laser, and the heat source of molten pool is laser. The calculated temperature of wire part outside the molten pool is verified by infrared ratio temperature measurement. The calculated temperature of wire part in the molten pool is verified by measurement of the molten pool size. Analyzing the wire temperature and welding process observed by the high speed video imaging, the temperature criteria of wire transfer behaviors are obtained. Thus, numerical simulation of the wire temperature can be used to predict wire transfer behaviors in laser hot wire welding. 相似文献
19.
焊丝送丝性能与表面状态关系研究 总被引:1,自引:0,他引:1
自动焊过程中,焊丝送丝性能是影响焊接接头质量的关键因素,论文以与焊丝送丝性能密切相关的焊丝表面状态为研究对象,以焊丝表面平坦面所占比例LD/LT及平坦面宽度偏离率KY描述焊丝表面状态,结合送丝性能与表面状态的关系,提出评价焊丝送丝性能的判据:焊丝表面平坦面所占比例LD/LT处在合理范围0.50~0.88,且KY小于30%时送丝性能优良,大于40%时送丝性能很差.对典型焊丝表面状态及其参数进行分析,并通过实际焊接过程送丝速度的稳定性评价焊丝送丝性能,验证所述判据的适用性. 相似文献