High temperature deformation behaviour of MoSi2 and WSi2 single crystals

High temperature deformation behaviour of MoSi₂ and WSi₂ single crystals, which both oriented near 001 and near 100, have been studied by compression tests over the temperature range of 1100 to 1500° C in a high vacuum of less than 6×10^–4 Pa. At elevated temperatures, several per cent compression deformation is possible in both MoSi₂ and WSi₂. Slips on {110 and {013 planes, the dislocation with the direction of Burgers vector 331 and the stacking fault on {110 plane are observed in both deformed MoSi₂ and WSi₂. In MoSi₂, the 0.2% offset stress of the sample oriented <001> is higher than that of the sample oriented <100>. The higher strength of the sample oriented <001> is related to the higher CRSS for the main slip plane of it. The reverse orientation dependence of the strength in WSi₂ is also correlated with the difference in CRSS on {110 and {013 planes, which shows the opposite result to MoSi₂. The higher CRSS on {110 plane in WSi₂ compared to that on {013 may be caused by the formation of a large number of stacking faults on {110 plane.     

Limits on Superconductivity in Nanoparticles and Nanowires

Recent experimental results are consistent with the prediction that superconductivity is suppressed in aluminum nanoparticles which are so small (10 nm diameter) that the electronic energy level spacing exceeds the superconducting energy gap in bulk material. Very recent experiments on nanowires (diameter 5–10 nm, length 150 nm) of MoGe indicate that a dissipative phase transition between superconducting and normal behavior occurs when the normal resistance of the wire equals the superconducting quantum resistance h/4e² 6.5 k.     

Sol-gel prepared Ni-alumina composite materials

The sol-gel method has been utilized for the preparation of dense, homogeneous ceramic-metal composites with up to 50% Ni in Al₂O₂. Examination by SEM and TEM shows that the materials consist of micrometre-size Al₂O₃ with metallic Ni in isolated regions from 50 m down to nanometre size. The density ranges from 97% (10% Ni) to 74% (50% Ni) of the theoretical number. The hardness decreases from 18 GPa for pure alumina to 10 GPa for alumina containing 50% Ni. The fracture toughness increases significantly from K _1c=3–4 MPa m^1/2 to K _1c=8.5 MPa m^1/2. The elastic and shear moduli decrease from E=400 GPa and G=160 GPa for pure alumina to E=320 GPa and G=135 GPa when containing 50% Ni. The electrical resistivity is 10⁶m with 10 to 40% Ni but decreases drastically at 50% Ni content.     

Measurement of the thermomechanical coefficient in confined normal liquid3He

The thermomechanical coefficient P/T has been measured for liquid³He from 2–20 mK. The temperature difference was established across³He in a porous plug with 90 nm pore diameter. The coefficient was 5 kPa K^–1 and only weakly temperature dependent; in terms of the heat capacity per unit volume, the coefficient varies from 4C at 2 mK to C at 20 mK.     

Particle size control of 1,3,5-triamino-2,4,6-trinitrobenzene by recrystallization from DMSO

Batches of up to 46g of the insensitive explosive 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) have been recrystallized from DMSO in an effort to prepare larger particle-size material for recycling previously-used TATB and also for use in special formulations. The first part of the study investigated the conditions required to shift the particle-size distribution maximum from 50–70 m to several hundred micrometres in diameter. Distributions peaking at 200–246 m were successfully produced by varying the cooldown rate and degree of agitation during cooling. The second part of the study emphasized regeneration of the standard 50–70 m distribution from submicron size (ultrafine TATB) particles. The distributions peaking at 76–88 m, 27–31 m, and 15–17 m, successfully bracketed the target particle sizes, were grown by changing the degree of solution saturation. The choice of saturation temperature for the TATB/DMSO solution was based on earlier small-scale recrystallization and solubility work.     

Equal-channel angular pressing of an Al-6061 metal matrix composite

An Al-6061 metal matrix composite, reinforced with 10 vol % Al₂O₃ particulates, was subjected to equal-channel angular (ECA) pressing at room temperature to a total strain of 5. It is shown that the intense plastic straining introduced by ECA pressing reduces the grain size from 35 m to 1 m and this leads to an increase in the microhardness measured at room temperature. Inspection revealed some limit cracking of the larger Al₂O₃ particulates as a consequence of the ECA pressing. Tensile testing after ECA pressing gave a maximum ductility of 235% at a temperature of 853 K when testing at strain rates from 10^–4 to 10^–3 s^–1. It is suggested that high strain rate superplasticity is not achieved in this material after ECA pressing due to the presence of relatively large Al₂O₃ particulates.     

On crystal alignment in polycrystalline YBCO materials based on TEM observation

Previously, we have observed that parallel lattice fringes show up regularly in MTG samples, indicative of good alignment of unit cells in strips of size 100 nm × a few times 100 nm. We have prepared films ( 80 nm) for TEM observation using YBCO material fabricated by the conventional solid-state reaction method in order to study the crystal texture in a length scale from a few 100 nm down to 3 Å. Parallel lattice fringes are observed to stretch across a cross-section 0.3×0.5 m². Cross lattice fringes intersecting at 90° and 45° are observed as rare events. This result suggests that the degree of alignment in the crystal texture is higher than expected inside a grain of size a few m.     

Microstructure-property studies in friction-stir welded, Thixomolded magnesium alloy AM60

Thixomolded magnesium alloy AM60 plates joined by friction-stir welding were observed to be as strong or stronger than the unwelded base material. The thixotropic microstructures of the as-molded plates consisted of either 3% or 18% primary solid fraction of -Mg globules (45 m average size) in a eutectic mixture consisting of -Mg grains (10 m) surrounded by Mg₁₇Al₁₂ intermetallic grains in the -Mg grain boundaries (having an average size of 1–2 m). This complex, composite microstructure became a homogeneous (Mg + 6% Al)), recrystallized, equiaxed grain (10–15 m) microstructure in the weld zone.     

CO/pH2: A Molecular Thermometer

We utilize reversible temperature dependent changes in the IR absorption spectrum of CO molecules isolated in solid parahydrogen (pH₂) to probe bulk temperature changes during rapid vapor deposition. The intensity of a well resolved feature near 2135 cm^–1 increases monotonically with temperature over the 2 to 5 K range. The thermally populated initial state of this transition lies 12 K above the CO/pH₂ ground state. During the deposition of 100 ppm CO/pH₂ samples, we detect temperature gradients 10 K/cm in 0.1 cm-thick samples subjected to heat loads 10 mW/cm². The resulting estimated thermal conductivity (TC) is 3(±2) mW/cm-K, averaged over the 2 to 5 K region. This value is 1000 times lower than the TC of single crystal solid pH₂, and 10 times lower than previously measured for pH₂ solids doped with 100 ppm concentrations of heavy impurities [Manzhelii, Gorodilov, and Krivchikov, Low Temp. Phys. 22, 131 (1996)]. We attribute this abnormally low TC to the known mixed fcc/hcp structure of the rapid vapor deposited solids.     

Microstructure and hardness of as-cast in situ TiB short fibre reinforced Ti-6Al matrix composites

XD^TM technique has been successfully used to prepare TiB short fibre reinforced Ti-6Al matrix composites. Macrostructure and microstructure have been observed by optical microscopy and SEM in order to study the influence of cooling rate on the morphology, size and distribution of TiB. Due to the cooling rate, there exist three kinds of macrostructure: fine grain zone, columnar grain zone and coarse equiaxed grain zone, corresponding to the cooling rate of 100–500 K/s, 20–50 K/s and less than 10 K/s respectively. In the fine grain zone, TiB distributes randomly in matrix with main rod morphology with 3 m in width and 50 m in length. In the columnar and coarse grain zone, a colony structure was observed in which TiB distributes with a special orientation direction with matrix. A lamellar TiB with up to 50 m width and 200 m length was also formed. It was indicated that the decreasing of the cooling rate changes the morphology of TiB from rod to lamellar shape, and markedly increase the length and aspect ration of TiB, from 50 m to 200 m and from about 15 to 200, respectively. TEM results show that the rod TiB has a hexagonal cross section. Vickers hardness testing shows a little reinforcement geometry dependence, but the average hardness of 484 MPa is much higher than that of unreinforced matrix alloy.     

The structure of sea urchin spines, large biogenic single crystals of calcite

Sea urchin spines are porous, single crystal Mg-rich calcite [(Mg, Ca)(CO₃)] with a three dimensional meshwork architecture. The crystallographic orientation of large (10 cm in length) spines from Heterocentrotus trigonarius was determined using the X-ray back-reflection Laue technique; the long axis of all spines is parallel to the 00·1 direction of calcite. The internal structure was studied using SEM and TEM. The macropore structure dominated the SEM images, whereas many small (80 nm) protein occlusions can be observed within the single crystal spines using TEM. The spines appeared crystallographically perfect in the TEM. The bend strengths of a group of spines were also determined and varied between 13 and 41 MPa.     

Widening the Scope of Working of Solid‐State Nd‐Glass Lasers

With the example of the serial model of a pulsed Ndglass laser, it is shown that the use of an unstable resonator with a semireflecting homogeneous exit mirror makes it possible to significantly decrease the laserbeam divergence and increase the uniformity of the radiationintensity distribution in the near zone. We were the first to obtain a laserbeam quality of (40–50) mm·mrad for technological glass lasers and to attain a depth of fusing of of 6.3 mm for steel (aspect ratio 10) for an energy of 23 J. The obtained uniformity of the radiationintensity distribution was estimated at the level of ±10%. The beamquality level attained for the Ndglass laser beam allows us to recommend it for both realization of deepfusion regimes and laser hardening without the use of external integrating optical elements.     

New high permittivity and low loss ceramics in the BaO–TiO2–Nb2O5 composition

New dielectric ceramics with formula BaTi3Nb4O17 and Ba6Ti14Nb2O39 have been prepared and characterized. BaTi3Nb4O17 was densified to 92% of TD after firing at 1310 °C for 4 h. However, Ba6Ti14Nb2O39 fired under optimized conditions (1260 °C for 4 h) showed only 85% TD together with secondary phase. The crystal system of both of the compositions is orthorhombic. The BaTi3Nb4O17 has r56, Qu2100 (at 4.402 GHz), f+86 p.p.m. K-1 and Ba6Ti14Nb2O39 as r50, Qu650 (4.359 GHz) and f+165 p.p.m. K-1. © 1998 Kluwer Academic Publishers     

Hydrothermal Synthesis and Spectroscopic Properties of Crystalline ZnO Powders and Films

Polycrystalline zinc oxide is synthesized under mild hydrothermal conditions (150–250°C). The phase composition, morphology, and pulsed cathodoluminescence (PCL) spectra of ZnO powders, polycrystalline films, and single crystals are studied as a function of synthesis conditions (the nature of the precursor, the type and concentration of the solvent, solution temperature, and the redox potential of the system). The crystallite size in the resultant materials varies from 100 nm to 10 m, depending on the synthesis conditions. The PCL spectra measured under pulsed electron-beam ( 2 ns) or laser (Nd:YAG, fourth harmonic, = 266 nm, 10 ns) excitation show two bands in the UV and visible spectral regions. The intensity ratio between these bands depends on the ZnO preparation conditions. The influence of the precursor and solvent on the PCL spectrum of ZnO is studied. The redox potential of the system is shown to have a strong effect on the luminescent properties of the resultant material.     

The role of Coble creep and interface control in superplastic Sn-Pb alloys

The creep behaviour of superplastic Sn-2 wt% Pb and Sn-38.1 wt % Pb is investigated at temperatures between 298 and 403 K and for grain sizes between 2.5 and 260m. In Sn-2 wt% Pb with grain sizes larger than 50 m, diffusion-controlled Coble creep is found and it is experimentally shown that this type of creep is inhibited in smallgrained specimens. Measurements covering low stresses ( 0.1 MPa) and strain rates ( 10^–10 sec^–1) rule out any explanation which relies on a threshold stress for plastic deformation. The observations are explained by a model in which, at low stresses or small grain sizes, Coble creep is rate-limited not by diffusion of vacancies but by the rate of emission and absorption at the curved dislocations in the grain boundaries which are the ultimate sources and sinks of vacancies.     

Strength and toughness of jade and related natural fibrous materials

Room temperature mechanical properties measured for natural fibrous jade materials with random fibre orientations were similar to strengths (e.g. 100 MPa) and toughnesses,K _IC, (e.g. 3M Pa m^1/2) in other studies. However, nearly three- and five-fold higher values were found respectively for strength and fracture toughness of jade with highly aligned fibres for crack propagation perpendicular to the fibres. Further, the results indicate significantly higher strength and toughness with decreasing fibre diameter and increasing aspect ratio, and an accompanying increase in intrafibre fracture. However, failure was predominantly catastrophic in character for all fibre orientations, indicating some material (i.e. matrix) is necessary for non-catastrophic failure as found in fibre composites.     

Electron diffraction study of superlattices and orientation variants in Ca3SrAl6SO16

Samples having the nominal composition of Ca₃SrAl₆SO₁₆ were sintered at 1380 °C and analysed by electron diffraction. The frequent appearances of forbidden and satellite reflections in this compound imply the presence of a number of basal and nonbasal superlattices so that the microstructure of this cement clinker was characterized by various superstructures including one-, two- and even three-dimensional superstructures along the 0 0 1, 1 1 0, 1 1 2, 1 1 4 or 2 2 1, 0 1 3 and 1 2 3 directions with repeat periods of two or three times of that of basic one, respectively, and intergrowth of these. Various domain structures with 90°, 120° and 48.2°, etc., orientation relationships were also detected in these superstructures and the total number of these orientation variants related to the symmetry elements lost in the process of phase transformation, can be predicted according to the conclusions of Van Tendeloo and Amerlinckx, or they are equal to the number of those unique planes in the matrix.     

The reflection of low energy phonons at the free surface of liquid4He. II. Experiment

Using a heater and bolometer as source and detector, the reflection of a pulsed beam of phonons at the free surface of liquid⁴He at 0.05 K has been measured for angles of incidence between 30 ° and 80 °. The energy distribution of the incident beam was obtained from the theory of phonon decay in the accompanying paper (I). The average incident phonon energy was 0.3 K, corresponding to an effective beam temperature of about 0.1 K. Both heater and bolometer were made from graphite resistor board with a layer of poly aniline fibers to increase the absorptivity for rotons. The angular distribution of the phonons from the heater is quite broad, approximately (cosⁿ +cos^m )/2 with n 0.65 and m 3.4. However, the receiver response has a broad component with n 2.2 and an extraordinarily narrow one with m 106. In agreement with the theory in I, the reflection appears to be specular within the accuracy of the experiment. The reflection coefficient is unity within the experimental error; the weighted mean value is 1.001±0.025. During the experiment, the free surface became contaminated with 0.034 of a monolayer of³He, but no effect from the³He impurity was observed.     

Effect of Air Oxidation on the Thermophysical Properties of a Zirconium Alloy

The results of an experimental study of the effect of air oxidation on the temperature dependence of the heat capacity and normal spectral emissivity (for the wavelength of 0.65 m) of the zirconium alloy E635 (1.3 mass% Sn, 0.3 mass% Fe, 1 mass% Nb) are presented. The subsecond resistive pulse heating technique has been used. The samples were heated in ambient air by single and multiple cyclic pulses.     

The laser surface-alloying of iron with carbon

Observations are reported on the structure of iron, laser surface-alloyed with carbon. Repeated laser surface-melting of iron pre-coated with DAG graphite has produced layers containing up to 6 wt % C, showing fine-scale white iron structures. Eutectic regions (interlamellar spacing 0.5m) have been shown by transmission electron microscopy to consist of Fe₃C + ferrite, the latter having formed by decomposition of austenite during solid state cooling. Regions of fine pearlite (spacing 55 nm) have also been observed. Carbon diffusion into the substrate during alloying produces a zone containing austenite and martensite.