共查询到20条相似文献,搜索用时 93 毫秒
1.
一种廉价的基于霍尔元件的电机转速测量装置的实现 总被引:7,自引:1,他引:6
李娟 《仪表技术与传感器》2002,(1):36-37
介绍了一种廉价的转速测量装置,包括用霍尔传感器和磁钢构成的脉冲发生器,与单片机的接口电路和倍频电路以及所采用的测速算法。 相似文献
2.
基于高速单片机和复杂可编程逻辑器件(CPLD)设计了一种具有霍尔位置传感器接口电路、电流采样电路以及编码器接口电路的无刷直流电机伺服控制器.该控制器可以实现无刷直流电机的有位置传感器控制和无位置传感器控制.以霍尔位置传感器的位置信号作为电机的换向信号并对该信号进行六倍频处理作为速度反馈,从而实现对电机的转速控制,给出了该控制系统的硬件结构设计和软件流程设计.试验结果表明:该无刷直流电机控制系统能够较好地实现电机的转速控制,为电机控制系统的设计提供了新思路. 相似文献
3.
在石油化工等领域各种液体的液位或界位测量是一种常见的测量,基于各种测量原理所开发的传感器也比较多样。根据应用场合要求不同,各种传感器又各有优缺点。采用开关型霍尔元件,按照一定的规则进行排列,设计了一种测量液位与界位的传感器。该传感器主要由带磁铁的移动浮子和固定不动的霍尔元件检测阵列两大部分组成,磁铁固定在浮子上,浮子与界位同步移动,使磁铁在霍尔元件检测阵列表面移动,霍尔元件检测阵列输出的脉冲信号数量与磁铁移动距离(界位移动距离)成正比。还分析了这种传感器的测量精度,给出了具体的处理电路。 相似文献
4.
严俊康 《仪表技术与传感器》1991,(1):37-38,10
本文介绍了使用单片机8035组成最小基本系统,加上少量接口电路和传感器制成的数字转速表。该表接收霍尔元件UGS3020T测得的转速脉冲,经单片机数字处理后,在输出口显示瞬时转速。 相似文献
5.
6.
7.
基于霍尔传感器工作原理,设计了柴油机低温起动系统的霍尔型起动电压、电流、转速传感器及其信号处理电路;利用新型的柴油机低温起动试验方案,进行了低温起动电压、起动电流、起动转速的性能试验,结果表明:最大低温起动电流达到680 A,起动电压大于8.6 V,起动平均转速为280 rad/min,性能完全满足柴油机低温起动系统要求。同时也验证了霍尔传感器能够准确测试柴油机低温起动系统的起动电压、电流和转速信号。 相似文献
8.
针对干簧管液位传感器的诸多缺点,构思了一种利用开关式霍尔片作为传感元件的液位测量传感器;霍尔式液位传感器的测量原理、测量电路进行了介绍;传感器的分辨率进行了讨论,最后通过实验数据分析对传感器进行了可行性验证。 相似文献
9.
10.
基于单片机的电机转速测量系统的设计 总被引:2,自引:0,他引:2
为了研制简单可靠的直流电机测速装置,提出了基于单片机和集成芯片设计电机转速测量系统的方案.介绍了霍尔传感器测速的工作原理,设计了系统的硬件电路和软件.该系统以AT89S51单片机为核心,主要包括电源模块、按键模块、转速测量电路模块和显示模块等,通过将脉冲信号送入单片机系统进行计数运算,并将转速测量结果显示在LED上.运行试验表明,系统结构简单,工作稳定可靠,满足电机的测速要求. 相似文献
11.
The demagnetizing current I
dc is measured in different areas of an electromagnet-article magnetic circuit at the moment of zero crossing of the magnetic
flux as the gap between the electromagnet and article changes. The weaker dependence of the I
dce magnitude measured in close proximity to the article on the gap width and the possibility of using the parameter in measuring
the coercive force of the article with an attachable transducer (in particular, with a Hall sensor) are demonstrated. 相似文献
12.
基于PLC的双恒压供水控制系统设计 总被引:4,自引:0,他引:4
该双恒压供水控制系统是以PLC控制为核心,变频调速技术为基础,并结合压力传感器、变频器、水泵、继电器、接触器等组成。在此系统中,PLC将压力设定值与测量值的偏差经PID运算后得到的控制量作用到变频器,从而通过变频器控制水泵的转速调节管网的压力,实现恒压供水的目的。 相似文献
13.
为解决传统齿轮齿距相对测量方法中存在的测量头直线进给和齿轮旋转速度同步困难的缺陷,提出一种基于微机和高速数据采集系统的齿轮齿距测量方法.通过增加霍尔开关获取齿轮转动速度,采用自适应控制技术实时调整测头进给时间间隔,从而实现了测量时间间隔与齿轮转动速度的智能化同步,并取得满意的效果. 相似文献
14.
介绍了采用集成传感器的工程机械液压系统检测仪的设计思想及硬、软件设计技术。阐述了温度、压力和流量三种参数测量电路的特点,提出并实现了三位一体的传感器设计,软件设计中采用了分频算法和非线性校正等技术。使用结果表明,该检测仪可以准确地测量液压系统参数,诊断液压系统的故障。 相似文献
15.
16.
基于DS18B20的数字式温度计设计 总被引:1,自引:0,他引:1
设计了以单片机STC89C52RC作为主控制器的数字式温度计.采用单线总线数字式温度传感器DS18B20采集环境温度,采用4位LED数码管显示.系统主要由主控制器、测温电路和显示电路组成,结合EDA软件仿真技术和在线编程技术实现温度的实时采集和显示,并通过硬件电路的验证.整个系统电路简单,测温准确,性能稳定. 相似文献
17.
为给自由涡轮转速装置的定检提供参考,设计了微型自由涡轮转速测试仪.硬件设计包括霍尔集成传感器、信号放大电路、单片机和液晶显示器四个模块;软件设计包括定时器TO的中断服务、计数器T1的脉冲计数和液晶的驱动三个模块.基于Proteus平台并利用模拟的霍尔脉冲信号对设计进行了仿真.结果表明.测试仪的软硬件设计正确. 相似文献
18.
The possibility of using Hall effect devices for measuring strong pulsed magnetic fields is studied. The Hall effect devices
with a∼10-mV/T sensitivity, based on 1- to 3-μm-thick n-type InAs polycrystalline films with a 103-cm2/(Vs) electron mobility and ∼1018-cm-3 concentration, are used. It is established that the Hall effect voltage of these devices is a linear function of the field
in magnetic fields with an induction of up to 56 T, and they are suitable for measuring unipolar strong pulsed magnetic fields
at induction variation rates of up to ~105T/s. It is necessary to use more sensitive Hall effect devices to obtain higher signal-to-noise ratios for rapidly measuring
alternating fields. 相似文献
19.
In dynamic testing of structures, rotational frequency response functions have been less utilized than its linear counterparts because no suitable moment generators and sensors for measuring moments and rotational motions are available. In this paper, a method and a new transducer for measuring point rotational impedance of structure is reported. The transducer contains two PZT bimorph cantilevers symmetrically attached to a solid base which is affixed to the measuring point of test structure. When the bimorph cantilevers are excited to vibrate out of phase with ac power, the transducer exerts a sinusoidal moment to the structure. To let the transducer measure rotational impedance simultaneously, a transducer model called “transduction matrix” is exploited. The matrix quantitatively relates the input voltage and current and the output moment and rotational velocity. Once the matrix is identified via tests and/or numerical simulation, the mechanical impedance at the output port can be evaluated from the electrical impedance measured at the input port of the transducer. To validate, the rotational impedance at a point of a beam was detected by the transducer and calculated by a finite element model. Comparisons of the results show that the proposed transducer fulfills the aimed measurement accurately. 相似文献