Oxygen diffusion into polystyrene–bentonite films

A simple fluorescence technique is proposed for the measurement of the diffusion coefficient of oxygen into polystyrene–clay composite films. The composite films were prepared from the mixture of surfactant-free pyrene (P)-labeled polystyrene latexes (PS) and modified bentonite (MNaLB) at various compositions at room temperature. These films were annealed at 200 °C above the glass transition (T_g) temperature of polystyrene for 10 min. Oxygen diffusion into the films was monitored with steady state fluorescence (SSF) measurements. Measurements were performed at room temperature for different film compositions (0, 5, 10, 20, 30, 50 and 60 mass% modified bentonite) films to evaluate the effect of MNaLB content on oxygen diffusion. The diffusion coefficient, D of oxygen was determined by the fluorescence quenching method by assuming Fickian transport and increased from 7.4 × 10^− 10 to 26.9 × 10^− 10 cm² s^− 1 with increasing MNaLB content. This increase in D value was explained by formation of microvoids in the film. These voids are large enough to contribute to the penetration of oxygen molecules through the films. The montmorillonite content did not affect the quenching rate constant, k_q and mutual diffusion coefficient, D_m values.     

Spatial variability of transport parameters in the Boom Clay

Several transport parameters (as hydraulic conductivity K, apparent diffusion coefficient D_p and diffusion accessible porosity η of HTO and iodide) have been intensively measured in the laboratory on high-quality cores taken at the Mol-1 borehole of the Mol site, in Belgium. The borehole was cored in 1997 from about 145 to 325 m depth, including the whole thickness of the Boom Formation, a Tertiary clay situated between 186 and 288 m depth (ground level), and part of the surrounding layers.The hydraulic conductivity measurements confirm the low permeability of the Boom Clay. An upper 90-m-thick clay layer within this formation can be considered as homogeneous with respect to the hydraulic conductivity. The vertical hydraulic conductivity K_v (i.e. K perpendicular to the bedding) is in the order of magnitude of 10⁻¹² m s⁻¹ and the average is 2.3×10⁻¹² m s⁻¹. This layer comprises from top to bottom the “Transition Zone”, the Putte Member, the Terhagen Member and the top of the Belsele-Waas Member of the Boom Formation. The 12 m at the base of the Formation, which corresponds to the lower part of the Belsele-Waas Member is characterised by larger K_v values (ranging between 10⁻¹¹ and 9×10⁻¹¹ m s⁻¹).The same thick clay layer can also be considered as homogeneous, regarding the values of the apparent diffusion coefficient and the diffusion accessible porosity η of tritiated water (HTO) and iodide. The average value of the diffusion accessible porosity is 0.37±0.03 for HTO and 0.16±0.02 for iodide. The apparent diffusion coefficient varies from 1.1×10⁻¹⁰ to 5.5×10⁻¹⁰ m² s⁻¹ for HTO and from 9.1×10⁻¹¹ to 5.2×10⁻¹⁰ m² s⁻¹ for iodide.     

Electrochemical behaviour of N-acetyl-l-cysteine on gold electrode—A tentative reaction mechanism

The electrochemical behaviour of N-acetyl-l-cysteine (NAC) has been investigated by linear and cyclic voltammetry on gold electrode at room temperature. The results showed two oxidation peaks under acid and neutral conditions and only one in basic medium. For each oxidation, as many electron was exchanged as proton. The influence of both the concentration and the potential scan rate on the peak currents highlighted a diffusion-controlled phenomenon for the first peak and an adsorption-limited reaction rate for the second one. The diffusion coefficient of NAC in solution and the surface concentration of the adsorbed species at pH 3 and 7 were close to 2 × 10⁻⁴ to 2 × 10⁻⁵ cm² s⁻¹ and 6 × 10⁻⁹ to 6 × 10⁻¹⁰ mol cm⁻², respectively. Film transfer experiments resulted in an irreversible adsorption of NAC on gold electrode, and the formation of a self-assembled monolayer (SAM).     

Novel coated graphite electrode for the selective determination of Gd(III) in rocks and waste water samples

A novel gadolinium selective coated graphite electrode based on 2,6-bis-[1-{N-cyanopropyl,N-(2-methylpridyl)}aminoethyl]pyridine [P] is described. The best performance was exhibited by the electrode having membrane composition P:NaTPB:PVC:NPOE as 8:4:30:58 (%, w/w). The electrode demonstrates excellent potentiometric characteristics towards gadolinium ion over several interfering ions. The electrode exhibited a Nernstian response to Gd³⁺ ion over a wide concentration range 2.8 × 10⁻⁷ to 5.0 × 10⁻² M with a detection limit (6.3 ± 0.1) × 10⁻⁸ M and slope 19.6 ± 0.1 mV decade⁻¹ of a_Gd³⁺. Furthermore, it showed a fast response time (12 s) and can be used for 2.5 months without significant divergence in its characteristics. Noticeably, the electrode can tolerate the concentration of different surfactants up to 1.0 × 10⁻⁴ M and can be used successfully in 30% (v/v) ethanol media and 10% (v/v) methanol and acetonitrile water mixture. The useful pH range of this sensor is 2.0 to 8.0. It is sufficiently selective and can be used for the determination of Gd³⁺ ions in waste water and rock samples. It also serves as a good indicator in the potentiometric titration of GdCl₃ with EDTA.     

Preparation and electrochemical properties of functionalized ionic liquid self-assembled modified graphite electrode

A modified graphite electrode with functionalized ionic liquid (IL) pyridinium derivative of β-cyclodextrin ([CDbPy]BF₄) was prepared by layer-by-layer self-assembly technique. With ferrocene as probe, the characterization of the (CDIL/PDDA)_n/GE SAMs in the solution of phosphate (PBS, pH 7.0) was investigated by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and chronocoulometry. The electrochemical behavior of p-chloronitrobenzene (p-CNB) at the modified electrode was studied. It was found that the modified electrode could catalyze the reduction of p-CNB and made the cathode peak move about 100 mV in positive direction in the solution of 0.1 mol/L PBS (pH 7.0). Differential pulse voltammetry (DPV) was applied to the determination of p-CNB in waste water with satisfactory results. The detection limit and the linear range of the concentration of p-CNB to the reduction peak current were 8.0 × 10⁻⁸ mol/L and 3.0 × 10⁻⁷–1.0 × 10⁻⁵ mol/L, respectively.     

Development and applications of quaternary ammonium (QA) membrane electrodes in pharmaceutical preparation and in bioavailability of Prostaglandin E1 and Deoxycholate

The two novel ion-pairs (PB-TPB and NB-TPB) of quaternary ammonium drugs; propantheline bromide (PB), N,N-Diisopropyl-N-methyl-N-[2-(xanthen-9ylcarbonyloxy)ethyl] ammonium bromide and neostigmine bromide (NB), 3-(dimethylcarbamoyloxy) phenyl]-trimethylazanium have been synthesized, respectively and incorporated in poly (vinyl chloride)-based membrane electrodes for the quantification of propantheline bromide and neostigmine bromide in different pharmaceutical preparations. The influences of membrane compositions on the potentiometric responses of membrane electrodes have been found to substantially improve the performance characteristics. The best performance was reported with membranes having composition (w/w) of PB-TPB or NB-TPB (6%): PVC (34%): o-NPOE (60%). The proposed electrodes exhibit nernstian response in the concentration ranges of 2.1 × 10⁻⁷ M to 1.0 × 10⁻² M and 4.4 × 10⁻⁷ M to 1.0 × 10⁻² M with detection limit of 1.5 × 10⁻⁷ M and 3.3 × 10⁻⁷ M, respectively. Both the membrane electrodes perform satisfactorily over pH ranges of (3.5–7.5 and 4.0–7.0) with fast response times (11 s and 13 s), respectively. These drugs (PB and NB) were further utilized as different ion-pairs of Prostaglandin E₁ (PGE₁) and Deoxycholate (DOC) in poly (vinyl chloride)-based membrane electrodes for the determination of bioavailability of Prostaglandin E₁ and Deoxycholate in plasma of different patients.     

Hybrid PAC-submerged membrane system for trace organics removal: I. Adsorption kinetics study of PAC in a bubbled solution

Part I of this study presents a theoretical method combined with experiments to determine the adsorption kinetics of powdered activated carbon (PAC) in the hybrid PAC-submerged membrane (SM) system with air bubbling for trace organics removal. The homogeneous surface diffusion model (HSDM) was applied to describe the kinetics of the adsorbate uptake. The differences between the model solutions and the corresponding experimental results were minimized by means of Levenberg–Marquardt algorithm so that two kinetic parameters D_S and k_f involved in HSDM were obtained simultaneously. The D_S was found to be 1.14 × 10⁻¹⁶ m²/s and the k_f value was correlated with the bubbling rate (Q_b) and carbon dosage (C_c), which are required in the modeling of the hybrid PAC-SM system presented in Part II of this study. The k_f was enhanced from 1.18 × 10⁻⁴ to 4.18 × 10⁻⁴ m/s when the bubbling intensity increased in the intermittent bubbling tests, suggesting that from energy consumption point of view, the high intensity intermittent bubbling is more efficient in improving the liquid film mass transfer than continuous bubbling with the same net bubbling rate.     

Immobilization of horseradish peroxidase on self-assembled (3-mercaptopropyl)trimethoxysilane film: Characterization, direct electrochemistry, redox thermodynamics and biosensing

Highly organized (3-mercaptopropyl)trimethoxysilane (3-MPT) films have been prepared via self-assembled coupled with sol–gel linking technology. Horseradish peroxidase (HRP) is successfully immobilized onto the densely packed three-dimensional (3D) 3-MPT network and the direct electrochemistry of HRP is achieved without any electron mediators or promoters. Redox thermodynamics of HRP on the 3-MPT films, which is obtained from the temperature dependence of the reduction potential, suggests that the positive shift of redox potentials of HRP at the interface of 3-MPT originates from the solvent reorganization effects and conformational change of the polypeptide chain of HRP. Based on the direct electrochemistry and electrocatalytic ability of HRP, a sensitive third-generation amperometric H₂O₂ biosensor is developed with two linear dependence ranges of 5.0 × 10⁻⁷ to 1.0 × 10⁻⁴ and 1.0 × 10⁻⁴ to 2.0 × 10⁻² mol L⁻¹.     

Evaluation of atrazine degradation in UV/FeZSM-5/H2O2 system using factorial experimental design

Degradation of atrazine in model wastewater by UV/FeZSM-5/H₂O₂ system chosen as optimal for application of advanced oxidation process (AOP) has been studied in a batch photo reactor. The statistical study of the process was performed using two-level full factorial experimental design with the three process parameters. Individual parameters and their interaction effects on atrazine degradation were determined and statistical model of process was developed. The optimal operating conditions were established. This approach has also given a broader insight of the processes that were occurring in the reaction system, and it has finally led to simplification in terms of kinetics. Atrazine degradation was described by pseudo-first-order kinetics with observed rate constant k′ = 2 × 10⁻³ s⁻¹.     

Carbon nanotube-supported Pd–ZnO catalyst for hydrogenation of CO2 to methanol

A type of Pd–ZnO catalysts supported on multi-walled carbon nanotubes (MWCNTs) were developed, with excellent performance for CO₂ hydrogenation to methanol. Under reaction conditions of 3.0 MPa and 523 K, the observed turnover-frequency of CO₂ hydrogenation reached 1.15 × 10⁻² s⁻¹ over the 16%Pd_0.1Zn₁/CNTs(h-type). This value was 1.17 and 1.18 times that (0.98 × 10⁻² and 0.97 × 10⁻² s⁻¹) of the 35%Pd_0.1Zn₁/AC and 20%Pd_0.1Zn₁/γ-Al₂O₃ catalysts with the respective optimal Pd_0.1Zn₁-loading. Using the MWCNTs in place of AC or γ-Al₂O₃ as the catalyst support displayed little change in the apparent activation energy for the CO₂ hydrogenation, but led to an increase of surface concentration of the Pd⁰-species in the form of PdZn alloys, a kind of catalytically active Pd⁰-species closely associated with the methanol generation. On the other hand, the MWCNT-supported Pd–ZnO catalyst could reversibly adsorb a greater amount of hydrogen at temperatures ranging from room temperature to 623 K. This unique feature would help to generate a micro-environment with higher concentration of active H-adspecies at the surface of the functioning catalyst, thus increasing the rate of surface hydrogenation reactions. In comparison with the “Parallel-type (p-type)” MWCNTs, the “Herringbone-type (h-type)” MWCNTs possess more active surface (with more dangling bonds), and thus, higher capacity for adsorbing H₂, which make their promoting action more remarkable.     

Electrical properties of V2O5–WO3/TiO2 EUROCAT catalysts evidence for redox process in selective catalytic reduction (SCR) deNOx reaction

Electrical conductivity measurements on EUROCAT V₂O₅–WO₃/TiO₂ catalyst and on its precursor without vanadia were performed at 300°C under pure oxygen to characterize the samples, under NO and under NH₃ to determine the mode of reactivity of these reactants and under two reaction mixtures ((i) 2000 ppm NO + 2000 ppm NH₃ without O₂, and (ii) 2000 ppm NO + 2000 ppm NH₃ + 500 ppm O₂) to put in evidence redox processes in SCR deNO_x reaction.It was first demonstrated that titania support contains certain amounts of dissolved W⁶⁺ and V⁵⁺ ions, whose dissolution in the lattice of titania creates an n-type doping effect. Electrical conductivity revealed that the so-called reference pure titania monolith was highly doped by heterovalent cations whose valency was higher than +4. Subsequent chemical analyses revealed that so-called pure titania reference catalyst was actually the WO₃/TiO₂ precursor of V₂O₅–WO₃/TiO₂ EUROCAT catalyst. It contained an average amount of 0.37 at.% W⁶⁺dissolved in titania, i.e. 1.07 × 10²⁰ W⁶⁺ cations dissolved/cm³ of titania. For the fresh catalyst, the mean amounts of W⁶⁺ and V⁵⁺ ions dissolved in titania were found to be equal to 1.07 × 10²⁰ and 4.47 × 10²⁰ cm⁻³, respectively. For the used catalyst, the mean amounts of W⁶⁺ and V⁵⁺ ions dissolved were found to be equal to 1.07 × 10²⁰ and 7.42 × 10²⁰ cm⁻³, respectively. Since fresh and used catalysts have similar compositions and similar catalytic behaviours, the only manifestation of ageing was a supplementary progressive dissolution of 2.9 × 10²⁰ additional V⁵⁺ cations in titania.After a prompt removal of oxygen, it appeared that NO alone has an electron acceptor character, linked to its possible ionosorption as NO⁻ and to the filling of anionic vacancies, mostly present on vanadia. Ammonia had a strong reducing behaviour with the formation of singly ionized vacancies. A subsequent introduction of NO indicated a donor character of this molecule, in opposition to its first adsorption. This was ascribed to its reaction with previously adsorbed ammonia strongly bound to acidic sites. Under NO + NH₃ reaction mixture in the absence of oxygen, the increase of electrical conductivity was ascribed to the formation of anionic vacancies, mainly on vanadia, created by dehydroxylation and dehydration of the surface. These anionic vacancies were initially subsequently filled by the oxygen atom of NO. N^o atoms, resulting from the dissociation of NO and from ammonia dehydrogenation, recombined into dinitrogen molecules. The reaction corresponded to

Full-size image

. In the presence of oxygen, NO did not exhibit anymore its electron acceptor character, since the filling of anionic vacancies was performed by oxygen from the gas phase. NO reacted directly with ammonia strongly bound on acidic sites. A tentative redox mechanism was proposed for both cases.     

Solubilities of actinides in a domestic groundwater and a bentonite porewater calculated by using PHREEQC

This study presents the solubilities and speciations of actinides, calculated by the PHREEQC (V.2) code in a granitic groundwater and a Ca-bentonite porewater under a reducing condition. The respective solubilities for the amorphous U, Am, Th, Np and Pu compounds in the groundwater were 2.2 × 10⁻⁵, 1.2 × 10⁻⁷, 3.1 × 10⁻⁹, 3.4 × 10⁻⁹ and 6.3 × 10⁻¹¹ mole/L, and these values are comparable to the results calculated by the MUGREM and EQ3/6 codes. The major dissolved species for U, Am, Th, Np and Pu were UO₂(OH)₃⁻, Am(OH)₂⁺, Th(OH)₄(aq), Np(OH)₃CO₃⁻ and Pu(OH)₃CO₃⁻, respectively. However, carbonate complex ions were anticipated as the major species in the porewater except for thorium due to an increase of the carbonate concentration and a decrease of the pH.     

Photodegradation of tetrahalobisphenol-A (X = Cl, Br) flame retardants and delineation of factors affecting the process

The photoassisted degradation (HPLC-UV absorption), dehalogenation (HPLC-IC) and mineralization (TOC decay) of the flame retardants tetrabromobisphenol-A (TBBPA) and tetrachlorobisphenol-A (TCBPA) were examined in UV-irradiated alkaline aqueous TiO₂ dispersions (pH 12), and for comparison the parent bisphenol-A (BPA, an endocrine disruptor) in pH 4–12 aqueous media to assess which factor impact most on the photodegradative process. Complete degradation (2.7–2.8 × 10⁻² min⁻¹) and dehalogenation (1.8 × 10⁻² min⁻¹) of TBBPA and TCBPA occurred within 2 h of UV irradiation, whereas only 45–60% mineralization (2.3–2.7 × 10⁻³ min⁻¹) was complete within 5 h for the flame retardants at pH 12 and ca. 80% for the parent BPA. Factors examined in the pH range 4–12 that impact the degradation of BPA were the point of zero charge of TiO₂ particles (pH_pzc; electrophoretic method), particle or aggregate sizes of TiO₂ (light scattering), and the relative number of OH radicals (as DMPO–OH adducts; ESR spectroscopy) produced in the UV-irradiated dispersion. Dynamics of BPA degradation (2.0–2.4 × 10⁻² min⁻¹) were pH-independent and independent of particle/aggregate size, but did correlate with the number of OH radicals, at least at pHs 4 to 8–9, after which the rates decreased somewhat at pH > 9 with decreasing adsorption owing to Coulombic repulsive forces between the very negative TiO₂ surface and the anionic forms of BPA (pK_as ca. 9.6–11.3), even though the number of OH radicals continued to increase at the higher pHs.     

Application of silica gel as an effective modifier for the voltammetric determination of dopamine in the presence of ascorbic acid and uric acid

Amorphous silica gel modified carbon paste electrode (CPE) offers substantial improvements in voltammetric sensitivity and selectivity towards determination of dopamine (DA). Cyclic voltammetry of Fe(CN)₆^3−/4− as a negatively charged probe revealed that the surface of the silica gel modified carbon paste electrode had a high density of negative charge at pH 8.0. Therefore, the modified electrode adsorbed DA (pK_a = 8.9) and enhanced its voltammetric response while repulsed ascorbic acid (AA) (pK_a = 4.2) and uric acid (UA) (pK_a = 5.4) and inhibited their interfering effects. The influence of various experimental parameters including percent of silica gel in the CPE, pH of solution, and accumulation time and potentials, on the voltammetric response of DA was investigated. At the optimum conditions, the analytical curve was linear for dopamine concentrations from 2.0 × 10⁻⁷ to 1.0 × 10⁻⁶ mol L⁻¹ and 2.0 × 10⁻⁶ to 1.5 × 10⁻⁴ mol L⁻¹ with a detection limit (3σ) of 4.8 × 10⁻⁸ mol L⁻¹. The prepared electrode was used for determination of DA spiked into DA injection and human serum samples, and very good recovery results were obtained over a wide concentration range of DA.     

Thermal stability of Mesoporous SBA-15 and Sn-SBA-15 Molecular Sieves: An in situ HTXRD study

Highly ordered SBA-15 and Sn-SBA-15 mesoporous molecular sieves with Si/Sn = 80, 60, 40 and 10 have been prepared through direct synthesis route under milder acidic conditions, which were used for the in situ high temperature X-ray diffraction (HTXRD) studies in the temperature range 298–1573 K for the first time in the literature. SBA-15 is found to be thermally stable up to 1473 K and appearance of α-cristobalite was observed at 1573 K also supported by the thermogravimetric (TG) data. A strong negative thermal expansion was observed on heating from 298 to 1573 K (α_a = −4.3 × 10⁻⁶ K⁻¹). Sn containing samples (Si/Sn = 80 and 60) showed a positive thermal expansion (6.75 × 10⁻⁶ K⁻¹ and 9.04 × 10⁻⁶ K⁻¹, respectively). On the other hand, the samples with Si/Sn = 40 and 10 showed a strong negative thermal expansion (−4.12 × 10⁻⁶ K⁻¹ and −7.56 × 10⁻⁶ K⁻¹) similar to SBA-15. The linear thermal expansion coefficient varied in the order: Si/Sn = 60 > 80 > 40 > 0 > 10. Sn⁴⁺ ions exhibit both tetrahedral and octahedral coordination depending upon the location of these ions either on the walls of the silica (Si/Sn = 80 and 60) or in the corona region of the structure (Si/Sn = 40 and 10), respectively. The thermal decomposition of the samples (TG data) is correlated to the thermal expansion behavior (HTXRD data). The decomposition behavior of template ions located within the pores is strongly influenced by the presence of Sn in the framework and a ‘soft’ interaction probably exists between the template ions and the Sn sites.     

Urea release rate from a scoop of coated pure urea beads: Unified extreme analysis

Urea release from a scoop of coated beads in a given volume of a well stirred liquid has been investigated analytically and experimentally. A method for determining the fractional cumulative release and fractional release rate curves for the scoop without knowing particle number and radii is presented. The representative D/K_b for a scoop of urea beads spray coated with ethyl cellulose is near 3.5 × 10⁻⁸ cm²/s, and that with cellulose acetate phthalate is near 7 × 10⁻⁸ cm²/s.     

Amperometric detection of hydrogen peroxide at nano-nickel oxide/thionine and celestine blue nanocomposite-modified glassy carbon electrodes

A simple procedure was developed to prepare a glassy carbon (GC) electrode modified with nickel oxide (NiOx) nanoparticles and water-soluble dyes. By immersing the GC/NiOx modified electrode into thionine (TH) or celestine blue (CB) solutions for a short period of time (5–120 s), a thin film of the proposed molecules was immobilized onto the electrode surface. The modified electrodes showed stable and a well-defined redox couples at a wide pH range (2–12), with surface confined characteristics. In comparison to usual methods for the immobilization of dye molecules, such as electropolymerization or adsorption on the surface of preanodized electrodes, the electrochemical reversibility and stability of these modified electrodes have been improved. The surface coverage and heterogeneous electron transfer rate constants (k_s) of thionin and celestin blue immobilized on a NiOx-GC electrode were approximately 3.5 × 10⁻¹⁰ mol cm⁻², 6.12 s⁻¹, 5.9 × 10⁻¹⁰ mol cm⁻² and 6.58 s⁻¹, respectively. The results clearly show the high loading ability of the NiOx nanoparticles and great facilitation of the electron transfer between the immobilized TH, CB and NiOx nanoparticles. The modified electrodes show excellent electrocatalytic activity toward hydrogen peroxide reduction at a reduced overpotential. The catalytic rate constants for hydrogen peroxide reduction at GC/NiOx/CB and GC/NiOx/TH were 7.96 (±0.2) × 10³ M⁻¹ s⁻¹ and 5.5 (±0.2) × 10³ M⁻¹ s⁻¹, respectively. The detection limit, sensitivity and linear concentration range for hydrogen peroxide detection were 1.67 μM, 4.14 nA μM⁻¹ nA μM⁻¹ and 5 μM to 20 mM, and 0.36 μM, 7.62 nA μM⁻¹, and 1 μM to 10 mM for the GC/NiOx/TH and GC/NiOx/CB modified electrodes, respectively. Compared to other modified electrodes, these modified electrodes have many advantages, such as remarkable catalytic activity, good reproducibility, simple preparation procedures and long-term stabilities of signal responses during hydrogen peroxide reduction.     

Study of LiNi0.5Mn1.5O4 synthesized via a chloride-ammonia co-precipitation method: Electrochemical performance, diffusion coefficient and capacity loss mechanism

LiNi_0.5Mn_1.5O₄ powders are prepared via a new co-precipitation method. In this method, chloride salts are used as precursors and ammonia as a precipitator. The impurity of chlorine can be removed via a thermal decomposition of NH₄Cl in the subsequent calcination. X-ray diffraction pattern reveals that the final product is a pure spinel phase of LiNi_0.5Mn_1.5O₄. Scanning electron microscopy shows that the powders have an octahedron shape with a particle size of about 2 μm. Electrochemical test shows that the LiNi_0.5Mn_1.5O₄ powders exhibit an excellent cycling performance and after 300 cycles, the capacity retention is 83%. The lithium diffusion coefficient is measured to be 5.94 × 10⁻¹¹ cm² s⁻¹ at 4.1 V, 4.35 × 10⁻¹⁰ cm² s⁻¹ at 4.75 V and 7.0 × 10⁻¹⁰ cm² s⁻¹ at 4.86 V. The mechanism of capacity loss is also explored. After 300 cycles, the cell parameter ‘a’ decreases by 0.54% for the quenched sample (LiNi_0.5Mn_1.5O_4−δ) and by 0.42% for the annealed sample (LiNi_0.5Mn_1.5O₄). Besides, it is the first time to identify experimentally that the Ni and Mn ions dissolved in the electrolyte can be further deposited on the surface of anode.     

Electrochemical performance of Li3V2(PO4)3/C cathode material using a novel carbon source

Polyethylene glycol (PEG, mean molecular weight of 10,000) has been used to prepare a Li₃V₂(PO₄)₃/C cathode material by a simple solid-state reaction. The Raman spectra shows that the coating carbon has a good structure with a low I_D/I_G ratio. The images of SEM and TEM show that the carbon is dispersed between the Li₃V₂(PO₄)₃ particles, which improves the electrical contact between the corresponding particles. The electronic conductivity of Li₃V₂(PO₄)₃/C composite is 7.0 × 10⁻¹ S/cm, increased by seven orders of magnitude compared with the pristine Li₃V₂(PO₄)₃ (2.3 × 10⁻⁸ S/cm). At a low discharge rate of 0.28C, the sample presents a high discharge capacity of 131.2 mAh/g, almost achieving the theoretical capacity (132 mAh/g) for the reversible cycling of two lithium. After 500 cycles, the discharge capacity is 123.9 mAh/g with only 5.6% fading of the initial specific capacity. The Li₃V₂(PO₄)₃/C material also exhibits an excellent rate capability with high discharge capacities of 115.2 mAh/g at 1C and 106.4 mAh/g at 5C.     

High-performance Li4Ti5−xVxO12 (0 ≤ x ≤ 0.3) as an anode material for secondary lithium-ion battery

Powders of spinel Li₄Ti_5−xV_xO₁₂ (0 ≤ x ≤ 0.3) were successfully synthesized by solid-state method. The structure and properties of Li₄Ti_5−xV_xO₁₂ (0 ≤ x ≤ 0.3) were examined by X-ray diffraction (XRD), Raman spectroscopy (RS), scanning electronic microscope (SEM), galvanostatic charge–discharge test and cyclic voltammetry (CV). XRD shows that the V⁵⁺ can partially replace Ti⁴⁺ and Li⁺ in the spinel and the doping V⁵⁺ ion does almost not affect the lattice parameter of Li₄Ti₅O₁₂. Raman spectra indicate that the Raman bands corresponding to the Li–O and Ti–O vibrations have a blue shift due to the doping vanadium ions, respectively. SEM exhibits that Li₄Ti_5−xV_xO₁₂ (0.05 ≤ x ≤ 0.25) samples have a relative uniform morphology with narrow size distribution. Charge–discharge test reveals that Li₄Ti_4.95V_0.05O₁₂ has the highest initial discharge capacity and cycling performance among all samples cycled between 1.0 and 2.0 V; Li₄Ti_4.9V_0.1O₁₂ has the highest initial discharge capacity and cycling performance among all samples cycled between 0.0 and 2.0 V or between 0.5 and 2.0 V. This excellent cycling capability is mainly due to the doping vanadium. CV reveals that electrolyte starts to decompose irreversibly below 1.0 V, and SEI film of Li₄Ti₅O₁₂ was formed at 0.7 V in the first discharge process; the Li₄Ti_4.9V_0.1O₁₂ sample has a good reversibility and its structure is very advantageous for the transportation of lithium-ions.