Phase equilibria in the Tl<Subscript>5</Subscript>Te<Subscript>3</Subscript>–Tl<Subscript>9</Subscript>BiTe<Subscript>6</Subscript>–Tl<Subscript>9</Subscript>TbTe<Subscript>6</Subscript> system

Phase equilibria in the Tl₅Te₃–Tl₉BiTe₆–Tl₉TbTe₆ system have been studied using differential thermal analysis, X-ray diffraction, and microhardness measurements. We have mapped out a number of vertical sections, the 760-K isothermal section of its phase diagram, and projections of its liquidus and solidus surfaces. The composition dependences of lattice parameters and microhardness have been obtained. The system has been shown to contain a continuous series of solid solutions, which crystallize in a tetragonal structure (Tl₅Te₃ type, sp. gr. I4/mcm).     

BaFe<Subscript>12</Subscript>O<Subscript>19</Subscript> films produced from BaFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/α-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> heterostructures

BaFe₁₂O₁₉ hexaferrite films have been produced on thermally oxidized single-crystal silicon (SiO₂/Si) substrates by sequential ion-beam sputtering of BaFe₂O₄ and α-Fe₂O₃ targets in an argon-oxygen atmosphere. Their crystal structure has been studied, and the origin of the impurity phases forming during heat treatment has been identified. The results show that heat treatment may lead to the formation of eutectic melts. As a result, the hexaferrite films may contain spherulites.     

Dielectric and piezoelectric properties of Bi<Subscript>0·5</Subscript>(Na<Subscript>0·82</Subscript>K<Subscript>0·18</Subscript>)<Subscript>0·5</Subscript> TiO<Subscript>3</Subscript>-LiSbO<Subscript>3</Subscript> lead-free piezoelectric ceramics

The (1−x)Bi_0·5(Na_0·82K_0·18)_0·5TiO_3−x LiSbO₃ (x = 0−0·03) lead-free piezoelectric ceramics were fabricated by a conventional solid-state reaction method and the effect of LiSbO₃ addition on microstructure and electrical properties of the ceramics was investigated. The results of XRD measurement show that Li⁺ and Sb⁵⁺ diffuse into the Bi_0·5(Na_0·82K_0·18)_0·5TiO₃ lattices to form a solid solution with a pure perovskite structure. The LiSbO₃ addition has no remarkable effect on the crystal structure. However, a significant change in grain size took place. Simultaneously, with increasing amount of LiSbO₃, the temperature for a antiferroelectric to paraelectric phase transition clearly increases. The piezoelectric constant d ₃₃ and the electromechanical coupling factor k _p show an obvious improvement by adding small amount of LiSbO₃, which shows optimum values of d ₃₃ = 175 pC/N and k _p = 0·36 at x = 0·01.     

Structural investigation of V<Subscript>2</Subscript>O<Subscript>5</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript>–K<Subscript>2</Subscript>O glass system with antibacterial potential

The xV₂O(1?x)[0.8 P₂O₅ ? 0.2 K₂O] glass system with 0 ≤ x ≤ 50 mol% was prepared and the structural changes induced in these glasses by increasing the vanadium oxide content were investigated by IR and ESR spectroscopies. The dual behaviour role of V₂O₅ oxide, as network modifier (for x ≤ 10 mol%) and the network former (x ≥ 20 mol%), as a consequence of phosphate network depolymerization and P–O–V and V–O–V linkages appearance was also highlighted. The antibacterial effect of the glasses with x ≤ 20 mol% V₂O₅ content was tested by optical density (OD) measurements. A linear correlation between the amount of vanadium and the antibacterial effect was evidenced.     

Phase equilibria in the Tl<Subscript>2</Subscript>Te–Tl<Subscript>5</Subscript>Te<Subscript>3</Subscript>–Tl<Subscript>9</Subscript>TbTe<Subscript>6</Subscript> system

The Tl₂Te–Tl₅Te₃–Tl₉TbTe₆ system has been studied using differential thermal analysis, X-ray diffraction, and microhardness measurements. We have mapped out a number of vertical sections, the 680 K isothermal section of its phase diagram, and projections of its polythermal projections of its liquidus and solidus surfaces. The field of solid solutions with the Tl₅Te₃ structure (δ-phase) has been shown to account for more than 90% of the area of the composition triangle. Tl₂Te-based solid solutions (α-phase) exist in a narrow composition region.     

High-damping and high-rigidity composites of Al<Subscript>2</Subscript>TiO<Subscript>5</Subscript>–MgTi<Subscript>2</Subscript>O<Subscript>5</Subscript> ceramics and acrylic resin

High-damping materials are widely used in engineering fields. In order to increase the precision of vibration control to different levels, high-damping materials with high-rigidity are required. This study attempts to develop a new high-damping high-rigidity material using ductile ceramics based on the Al₂TiO₅–MgTi₂O₅ system, which has many continuous microcracks along the grain boundaries. Ductile ceramics have high internal friction (Q ⁻¹ = 0.01–0.037), but very low rigidity (<10 GPa). The rigidity of Al₂TiO₅–MgTi₂O₅ ceramics was improved by combining them with a polymer such as acrylic resin. The Young’s modulus and internal friction of the composites of Al₂TiO₅–MgTi₂O₅ ceramics and acrylic resin are investigated. They show high-damping capacity (Q ⁻¹ = 0.03–0.04) with high rigidity (E = 50–60 GPa), and their properties depend on those of the polymer. Thus, the composites fabricated using the above method can serve as high-damping high-rigidity materials.     

Chemical interaction of InAs,InSb, GaAs,and GaSb with (NH<Subscript>4</Subscript>)<Subscript>2</Subscript>Cr<Subscript>2</Subscript>O<Subscript>7</Subscript>–HBr–C<Subscript>4</Subscript>H<Subscript>6</Subscript>O<Subscript>6</Subscript> etching solutions

This paper presents results on the kinetics and mechanism of the physicochemical interaction of InAs, InSb, GaAs, and GaSb semiconductor surfaces with (NH₄)₂Cr₂O₇–HBr–C₄H₆O₆ etching solutions under reproducible hydrodynamic conditions in the case of laminar etchant flow over a substrate. We have identified regions of polishing and nonpolishing solutions and evaluated the apparent activation energy of the process. The surface morphology of the crystals has been examined by microstructural analysis after chemical etching. The results demonstrate that the presence of C₄H₆O₆ in etchants helps to reduce the overall reaction rate and extend the region of polishing solutions.     

Evaluation of CaO–SiO<Subscript>2</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript>–Na<Subscript>2</Subscript>O–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> bioglass-ceramics for hyperthermia application

Magnetic bioglass ceramics (MBC) are being considered for use as thermoseeds in hyperthermia treatment of cancer. While the bioactivity in MBCs is attributed to the formation of the bone minerals such as crystalline apatite, wollastonite, etc. in a physiological environment, the magnetic property arises from the magnetite [Fe₃O₄] present in these implant materials. A new set of bioglasses with compositions 41CaO · (52 ? x)SiO₂ · 4P₂O₅  · xFe₂O₃ · 3Na₂O (2 ≤ x ≤ 10 mol% Fe₂O₃) have been prepared by melt quenching method. The as-quenched glasses were then heat treated at 1050°C for 3 h to obtain the glass-ceramics. The structure and microstructure of the samples were characterized using X-ray diffraction and microscopy techniques. X-ray diffraction data revealed the presence of magnetite in the heat treated samples with x ≥ 2 mol% Fe₂O₃. Room temperature magnetic property of the heat treated samples was investigated using a Vibrating Sample Magnetometer. Field scans up to 20 kOe revealed that the glass ceramic samples had a high saturation magnetization and low coercivity. Room temperature hysteresis cycles were also recorded at 500 Oe to ascertain the magnetic properties at clinically amenable field strengths. The area under the magnetic hysteresis loop is a measure of the heat generated by the MBC. The coercivity of the samples is another important factor for hyperthermia applications. The area under the loop increases with an increase in Fe₂O₃ molar concentration and the. coercivity decreases with an increase in Fe₂O₃ molar concentration The evolution of magnetic properties in these MBCs as a function of Fe₂O₃ molar concentration is discussed and correlated with the amount of magnetite present in them.     

Variable—Range hopping in Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>-K<Subscript>2</Subscript>B<Subscript>4</Subscript>O<Subscript>7</Subscript> glasses

The dc conductivity of the glasses in the Fe₂O₃-Bi₂O₃-K₂B₄O₇ system was studied at temperatures between 223 and 393 K. At temperatures from 300 to 223 K, T^–1/4 (T is temperature) dependence of the conductivity was found, however, both Mott variable-range hopping and Greaves intermediate range hopping models are found to be applicable. Mott and Greaves parameters analysis gave the density of states at Fermi level N (E_F) = 3.13 × 10²⁰–21.01 × 10²⁰ and 1.93 × 10²¹–16.39 × 10²¹ cm^–3eV^–1 at 240 K, respectively. The variable-range hopping conduction occurred in the temperature range T = 300–223 K, since W_D was found to be large (W_D = 0.08–0.14 eV for these glasses) and dominated the conduction at T < 300 K.     

Highly Oxygen-Permeable NiV<Subscript>2</Subscript>O<Subscript>6</Subscript>–25 wt % V<Subscript>2</Subscript>O<Subscript>5</Subscript> Molten-Oxide Membrane Material

A NiV₂O₆–25 wt % V₂O₅ molten-oxide material has been prepared and characterized, and its transport properties (electrical conductivity, oxygen ion transport number, and oxygen permeability) have been studied in the temperature range 680–700°C. The results demonstrate that the molten-oxide membrane material obtained possesses high selective oxygen permeability (KO₂ = (2.5–5.6) × 10^–10 mol/(cm s) in the range 680–740°C and \(\frac{{{j_{{O_2}}}}}{{{j_{{N_2}}}}}\) ~ 1500) and can be used in separators for the preparation of extrapure oxygen from air.     

Crystal structure of a Np(V) sesquioxalate,Na<Subscript>4</Subscript>(NpO<Subscript>2</Subscript>)<Subscript>2</Subscript>(C<Subscript>2</Subscript>O<Subscript>4</Subscript>)<Subscript>3</Subscript>·2H<Subscript>2</Subscript>O

The crystal structure of a previously unknown Np(V) sesquioxalate, Na₄(NpO₂)₂(C₂O₄)₃·2H₂O was studied. The crystal structure consists of neptunyl(V) cations, sodium cations, oxalate anions, and water molecules of crystallization. Neptunyl(V) cations and oxalate ions form anionic chains [(NpO₂)₂(C₂O₄)₃] _n ^4n? . The coordination polyhedron (CP) of Np (pentagonal bipyramid) contains two apical “yl” oxygen atoms and five equatorial O atoms of three oxalate ions. The CP of Na(1) and Na(2) cations are combined through the common edges into zigzag chains in the [010] direction. Two independent oxalate ions are tridentate and tetradentate ligands.     

Kinetics of Thermal Transformation of Mg<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript> · 8H<Subscript>2</Subscript>O to Mg<Subscript>3</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript>

The kinetics of thermal dehydration of Mg₃(PO₄)₂ · 8H₂O was investigated using thermogravimetry at four different heating rates. The activation energies of the dehydration step of Mg₃(PO₄)₂ · 8H₂O were calculated through the isoconversional Ozawa and Kissinger-Akahira-Sunose (KAS) methods and iterative methods, which were found to be consistent and indicate a single mechanism. The possible conversion function of the dehydration reaction for Mg₃(PO₄)₂ · 8H₂O has been estimated through the Coats and Redfern integral equation, and a better kinetic model such as random nucleation of the “Avrami–Erofeev equation (A _3/2 model)” was found. The thermodynamic functions (ΔH*, ΔG*, and ΔS*) of the dehydration reaction are calculated by the activated complex theory and indicate that it is a non-spontaneous process when the introduction of heat is not connected.     

Preparation and properties of Bi<Subscript>6</Subscript>Ti<Subscript>5</Subscript>WO<Subscript>22</Subscript>: a new phase in the Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>–TiO<Subscript>2</Subscript>–WO<Subscript>3</Subscript> system

In a recent report, the evaluation of the phase relations in the Bi₂O₃–TiO₂–WO₃ ternary system has shown the existence of a new phase with nominal composition close to Bi₆Ti₅WO₂₂. In the present contribution we attempt to prepare this single phase by using a solid state route. Although XRD analyses also show traces of two minority Aurivillius-type phases in the synthesized materials, the crystal structure of the Bi₆Ti₅WO₂₂ phase has been determined by Rietveld analyses revealing a complex structure similar to that of Bi₃(AlSb₂)O₁₁ and PbHoAl₃O₈ related compounds. The electrical response of this new phase was characterized as well. Three peaks are observed in its dielectric response: two of them positioned around 0 °C and can be assigned to this Bi₆Ti₅WO₂₂ structure. The third one rises up to 665 °C and confirms the presence of the Aurivillius-type phases.     

Synthesis of thorn-like Ca<Subscript>2</Subscript>B<Subscript>2</Subscript>O<Subscript>5</Subscript>·H<Subscript>2</Subscript>O by hydrothermal method

Thorn-like polycrystalline Ca₂B₂O₅·H₂O microspheres with nano-sized slices were synthesized using boric acid and calcium hydroxide as reactants by a facile catalyst-free hydrothermal method at low temperature. The products were characterized by means of X-ray powder diffraction (XRD) and scanning electron microscopy (SEM). The XRD pattern reveals that the Ca₂B₂O₅·H₂O is a monoclinic phase polycrystalline with cell parameters a = 0·6702, b = 0·5419 and c = 0·3558 nm. SEM also reveals that the monoclinic phase polycrystalline are thorn-like microspheres composed of many flakes with an average thickness of <100 nm. Possible reaction and growth mechanism were also discussed.     

Structural investigations of V<Subscript>2</Subscript>O<Subscript>5</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript>–CaO glass system by FT-IR and EPR spectroscopies

xV₂O₅·(100 − x)[0.7P₂O₅·0.3CaO] glass system was obtained for 0 ≤ x ≤ 35 mol% V₂O₅. In order to obtain information regarding their structure, several techniques such as X-Ray diffraction, FT-IR, and EPR spectroscopies were used. X-Ray diffraction patterns of investigated samples are characteristic of vitreous solids. FT-IR spectra of 0.7P₂O₅·0.3CaO glass matrix and its deconvolution show the presence in the glass structure of all structural units characteristic to P₂O₅. Their number are increasing for x ≤ 3 mol% V₂O₅ then, for higher content of vanadium ions, the number of phosphate structural units are decreasing leading to a depolymerization of the structure. The structural units characteristic to V₂O₅ were not evidenced but their contribution to the glass structure can be clearly observed. EPR revealed a well resolved hyperfine structure (hfs) typical for vanadyl ions in a C_4v symmetry for x ≤ 3 mol% V₂O₅. For 5 < x < 20 mol% V₂O₅ the spectra show a superposition of two EPR signals one due to a hfs structure and another consisting of a broad line typical for associated V⁴⁺–V⁴⁺ ions. For x ≥ 20 mol% V₂O₅ only the broad line can be observed. The composition dependence of the line-width suggests the presence of dipole–dipole interaction between vanadium ions up to x ≤ 5 mol% V₂O₅ and superexchange interactions between vanadium ions for x > 5 mol% V₂O₅.     

Ca<Subscript>4</Subscript>La<Subscript>2</Subscript>Ti<Subscript>5</Subscript>O<Subscript>17</Subscript>: a novel low loss dielectric ceramics in the CaO–La<Subscript>2</Subscript>O<Subscript>3</Subscript>–TiO<Subscript>2 </Subscript>system

A novel low loss dielectric material Ca₄La₂Ti₅O₁₇ was prepared by solid state ceramic route. The structure and microstructure of the Ca₄La₂Ti₅O₁₇ ceramics was investigated using XRD, SEM and EDX techniques. XRD result showed cubic perovskite like structure for Ca₄La₂Ti₅O₁₇ ceramics. The ceramics were sintered in the temperature range of 1,450–1575 °C. The microwave dielectric properties of the material were investigated using a network analyzer in the frequency range of 3–6 GHz. The variation in microwave dielectric properties of the Ca₄La₂Ti₅O₁₇ ceramics with sintering temperature was correlated with bulk density of the material. Ca₄La₂Ti₅O₁₇ has ε_r of 73, Q_uxf of 16,000 at 3.3 GHz, and τ_f of 127 ppm/°C at the optimized sintering temperature of 1,550 °C/4h.     

Fabrication of Yb<Subscript>2</Subscript>O<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript>–SiO<Subscript>2</Subscript> Optical Fibers with a Perfect Step-Index Profile by the MCVD Process

An all-vapor phase MCVD process has been proposed for the fabrication of fiber preforms with a Yb₂O₃–Al₂O₃–P₂O₅–SiO₂ multicomponent glass core. We have investigated the tubular preform collapse into a rod and demonstrated approaches capable of preventing P₂O₅ losses in the central part of the core during the collapse process. Preforms with a flat, perfect step-index profile have been fabricated.     

Phase equilibria in the system “CaAl<Subscript>2</Subscript>Si<Subscript>3</Subscript>O<Subscript>10</Subscript>”-Na<Subscript>2</Subscript>Al<Subscript>2</Subscript>Si<Subscript>3</Subscript>O<Subscript>10</Subscript>-H<Subscript>2</Subscript>O

The phase equilibria in the “CaAl₂Si₃O₁₀”-Na₂Al₂Si₃O₁₀-H₂O system are analyzed using structural and thermal analysis data, and the ideal gonnardite structure is modeled. The results suggest that, to ensure a better correlation with the structures of the zeolites in this series, a new structural model of the gonnardite-based solid solution must be selected, with the structure rotated through 45° about the c axis in the ab plane.     

Synthesis and study of structural,dielectric, magnetic and magnetoelectric properties of K<Subscript>0.5</Subscript>Na<Subscript>0.5</Subscript>NbO<Subscript>3</Subscript>–CoMn<Subscript>0.2</Subscript>Fe<Subscript>1.8</Subscript>O<Subscript>4</Subscript> composites

Magnetoelectric (ME) composites consisting of K_0.5Na_0.5NbO₃ (KNN) as ferroelectric phase and CoMn_0.2Fe_1.8O₄ (CMFO) as ferrite phase with general formula (x) CoMn_0.2Fe_1.8O₄–(1???x) K_0.5Na_0.5NbO₃ (x?=?10, 20, 30, 40 and 50 wt%) were synthesized using solid state reaction method. X-ray diffraction analysis asserts the existence of component phases including spinel phase of CMFO and orthorhombic phase of KNN. Field emission scanning electron microscopy has been used for studying the morphology and calculation of average grain size. The temperature dependent dielectric properties including dielectric constant (\(\varepsilon ^{\prime}\)) and dielectric loss (tan δ) at different frequencies has been studied and both are found to increase with incorporation of CMFO. Magnetic hysteresis loops have been measured at temperatures of 300 and 5 K. Variation of magnetization versus temperature has been studied in field cooled and zero field cooled modes. Polarization versus electric field (P–E) hysteresis loops are obtained at room temperature indicating presence of ferroelectric ordering in the composites at room temperature. The remnant polarization (2P_r) and coercive field (2E_c) are found to decrease linearly with incorporation of CMFO. ME voltage coefficient (α_ME) has been measured. The maximum value of α_ME is found to be 5.941 mV/cm-Oe for 10% CMFO–90% KNN bulk composite.     

Synthesis of CaO–SiO<Subscript>2</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript> mesoporous bioactive glasses with high P<Subscript>2</Subscript>O<Subscript>5</Subscript> content by evaporation induced self assembly process

Mesoporous bioactive glasses (MBGs) of the CaO–SiO₂–P₂O₅ system containing relatively high P₂O₅ contents (10–30 mol%) were prepared from a sol–gel. An evaporation-induced self-assembly (EISA) technique was used with poly(ethylene oxide)-block–poly(propylene oxide)-block–poly(ethylene oxide) (EO₂₀–PO₇₀–EO₂₀, P123) acting as a template. The structural, morphological and textural properties of MBGs were investigated by small-angle X-ray diffraction (SAXRD), transmission electron microscopy (TEM), Fourier transform infrared (FTIR) spectroscopy and a N₂ sorption/desorption technique. SAXRD and TEM results display the reduced long-range ordering of mesopores with increasing P₂O₅ content. N₂ sorption/desorption analysis shows that all three samples exhibit a type IV isotherm with type H1 hysteresis loops, characteristic of independent cylindrical slim pore channels and this material has a Barret–Joyner–Halenda (BJH) model pore size of ~4 nm and BET specific surface area ~430 m²/g. NMR results indicate a more condensed framework for samples with 30 mol% P₂O₅ than samples with 10 mol% P₂O₅. For in vitro bioactivity tests where samples were soaked in simulated body fluid (SBF), samples with 30 mol% P₂O₅ showed higher crystallinity than those with lower P₂O₅ contents Silicon concentration increased in SBF solution during the soaking period, which indicates MBGs can be degradable in SBF solution.