Thermal shock behavior of nanostructured and conventional Al2O3/13 wt%TiO2 coatings fabricated by plasma spraying

The thermal shock behavior of three kinds of Al₂O₃/13 wt%TiO₂ coatings fabricated by plasma spraying was studied in this paper. One kind of those coatings was derived from conventional fused and crushed feedstock powder available commercially; the other two kinds of coatings were derived from nanostructured agglomerated feedstock powders. These two nano coatings possess moderate pores and pre-existing microcracks, they were composed of fused structure and three-dimensional net or skeleton-like structure. For conventional coatings, the pores and pre-existing cracks were bigger, sharp-point and mostly distributed between splats. Thermal shock tests for the three coatings were performed by water quenching method. Testing result showed the two kinds of nano coatings had much higher thermal shock resistance than the conventional coatings. The improved thermal shock resistance for nano coatings could attribute to their improved microstructure and crack propagation mode. The damage evolution and failure mechanism of coatings was quite different at thermal shock temperature of 650 °C and 850 °C, which was explained by a simple model. Different crack propagating modes in nanostructured and conventional coatings during thermal shock tests were due to their different microstructures in these two kinds coatings. The stress state of coating surfaces during the thermal cycles was also discussed in this paper.     

Deposition of Al2O3-TiO2 Nanostructured Powders by Atmospheric Plasma Spraying

Al₂O₃-13%TiO₂ coatings were deposited on stainless steel substrates from conventional and nanostructured powders using atmospheric plasma spraying (APS). A complete characterization of the feedstock confirmed its nanostructured nature. Coating microstructures and phase compositions were characterized using SEM, TEM, and XRD techniques. The microstructure comprised two clearly differentiated regions. One region, completely fused, consisted mainly of nanometer-sized grains of γ-Al₂O₃ with dissolved Ti⁺⁴. The other region, partly fused, retained the microstructure of the starting powder and was principally made up of submicrometer-sized grains of α-Al₂O₃, as confirmed by TEM. Coating microhardness as well as tribological behavior were determined. Vickers microhardness values of conventional coatings were in average slightly lower than the values for nanostructured coating. The wear resistance of conventional coatings was shown to be lower than that of nanostructured coatings as a consequence of Ti segregation. A correlation between the final properties, the coating microstructure, and the feedstock characteristics is given.     

Effects of critical plasma spray parameter and spray distance on wear resistance of Al2O3-8 wt.%TiO2 coatings plasma-sprayed with nanopowders

Effects of plasma spraying conditions on wear resistance of nanostructured Al₂O₃-8 wt.%TiO₂ coatings plasma-sprayed with nanopowders were investigated in this study. Five kinds of nanostructured coatings were plasma-sprayed on a low-carbon steel substrate by varying critical plasma spray parameter (CPSP) and spray distance. The coatings consisted of fully melted region of γ-Al₂O₃ and partially melted region, and the fraction of the partially melted regions and pores decreased with increasing CPSP or decreasing spray distance. The hardness and wear test results revealed that the hardness of the coatings increased with increasing CPSP or decreasing spray distance, and that the hardness increase generally led to the increase in wear resistance, although the hardness and wear resistance were not correlated in the coating fabricated with the low CPSP. The main wear mechanism was a delamination one in the coatings, but an abrasive wear mode also appeared in the coating fabricated with the low CPSP. According to these wear mechanisms, the improvement of wear resistance in the coating fabricated with the low CPSP could be explained because the improved resistance to fracture due to the presence of partially melted regions might compensate a deleterious effect of the hardness decrease.     

Microstructure, spallation and corrosion of plasma sprayed Al2O3–13%TiO2 coatings

The electrochemical corrosion behaviours of the steel substrates coated with three different plasma sprayed Al₂O₃–13%TiO₂ coatings were studied in this paper. The three kinds of Al₂O₃–13%TiO₂ coatings were conventional ME coating, nanostructured NP coating and NS coating. There were micro cracks, laminar splats and straight columnar grains in ME coating. For the two nanostructured coatings, the laminar microstructure and columnar grains were not obvious. The NP coating had the highest hardness and spallation resistance. Electrochemical corrosion behaviour of the three coatings was mainly investigated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) in aqueous Na₂SO₄ solution.     

HVOF-Sprayed Coatings Engineered from Mixtures of Nanostructured and Submicron Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript> Powders: An Enhanced Wear Performance

In previous studies, it has been demonstrated that nanostructured Al₂O₃-13 wt.%TiO₂ coatings deposited via air plasma spray (APS) exhibit higher wear resistance when compared to that of conventional coatings. This study aimed to verify if high-velocity oxy-fuel (HVOF)-sprayed Al₂O₃-13 wt.%TiO₂ coatings produced using hybrid (nano + submicron) powders could improve even further the already recognized good wear properties of the APS nanostructured coatings. According to the abrasion test results (ASTM G 64), there was an improvement in wear performance by a factor of 8 for the HVOF-sprayed hybrid coating as compared to the best performing APS conventional coating. When comparing both hybrid and conventional HVOF-sprayed coatings, there was an improvement in wear performance by a factor of 4 when using the hybrid material. The results show a significant antiwear improvement provided by the hybrid material. Scanning electron microscopy (SEM) at low/high magnifications showed the distinctive microstructure of the HVOF-sprayed hybrid coating, which helps to explain its excellent wear performance. This article is an invited paper selected from presentations at the 2007 International Thermal Spray Conference and has been expanded from the original presentation. It is simultaneously published in Global Coating Solutions, Proceedings of the 2007 International Thermal Spray Conference, Beijing, China, May 14-16, 2007, Basil R. Marple, Margaret M. Hyland, Yuk-Chiu Lau, Chang-Jiu Li, Rogerio S. Lima, and Ghislain Montavon, Ed., ASM International, Materials Park, OH, 2007.     

Influence of liquid nitrogen quenching on the evolution of metastable phases during plasma spraying of (ZrO2–5 wt.% Y2O3)–20 wt.% Al2O3 coatings

The preparation of nanostructured (ZrO₂–5 wt.% Y₂O₃)–20 wt.% Al₂O₃ coatings by atmospheric plasma spraying of commercially available micron-scale powders is reported. Materials were prepared by means of a standard spraying technique and by using an improved technique that allows for the quenching of the material using liquid nitrogen-cooled substrates. Quenching leads to the controlled formation of metastable phases. The influence of liquid nitrogen cooling on the formation of the metastable phases was studied by X-ray diffraction under a grazing incidence angle of 1°. A significant increase in the amount of the metastable zirconia phase and a more homogeneous composition along the thickness were found compared to the regularly sprayed coatings. All materials were subjected to a thermal treatment for 1 h at 1400 °C to study the evolution of stable phases.     

Preparation and characterization of nanostructured Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-13wt.%TiO<Subscript>2</Subscript> ceramic coatings by plasma spraying

Nanostructured and conventional Al₂O₃-13wt.%TiO₂ ceramic coatings were prepared by plasma spraying with nanostructured agglomerated and conventional powders, respectively. The microstructure and microhardness of the coatings were investigated using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and microhardness measurement. Meanwhile, the friction and wear behaviors were analyzed and compared using a ball-on-disk tribometer. The results show that the conventional coating has lamellar stacking characteristic and has some pores. However, the nanostructured coating shows a bimodal microstructure, which is composed of both fully melted regions and partially melted regions. According to the microstructural difference, the partially melted regions can be divided into liquid-phase sintered regions (a three-dimensional net or skeleton-like structure: Al₂O₃-rich submicron particles embedded in the TiO₂-rich matrix) and solid-phase sintered regions (remained nanoparticles). The microstructural characteristics of the liquid-phase sintered region are formed due to the selective melting of TiO₂ nanoparticles during plasma spraying. On the other hand, the TiO₂ and Al₂O₃ nanoparticles of the solid-phase sintered regions are all unmelted during plasma spraying. Due to the existence of nanostructured microstructures, the nanostructured coating has a higher microhardness, a lower friction coefficient, and a better wear resistance than the conventional coating.     

Mechanical and tribological performance of Al2O3-TiO2 coatings elaborated by flame and plasma spraying

Mechanical properties and wear rates of Al₂O₃-13 wt.% TiO₂ (AT-13) and Al₂O₃-43 wt.% TiO₂ (AT-43) coatings obtained by flame and atmospheric plasma spraying were studied. The feed stock was either ceramic cords or powders. Results show that the wear resistance of AT-13 coatings is higher than that of AT-43 and it seems that the effect of hardness on wear resistance is more important than that of toughness. Additionally, it was established that, according to conditions used to elaborate coatings and the sliding tribological test chosen, spray processes do not seem to have an important effect on the wear resistance of these coatings.     

Microstructural characterization of plasma sprayed Al2O3-40 wt.% TiO2 coatings on high density graphite with different post-treatments

Graphite is one of the candidate materials proposed for application in pyrochemical reprocessing plants involving aggressive molten chloride environment. Post treatments are promising techniques for the improvement of properties of thermal spray coatings for different industrial applications. In the present work, the effect of post treatments like vacuum annealing (VA) and laser melting (LM) on the microstructure and chemical modification of plasma sprayed Al₂O₃-40 wt.% TiO₂ coatings over high density (HD) graphite substrates has been investigated. When compared with sprayed coatings (SC), VA coatings showed cluster morphology and LM coatings exhibited homogenous microstructure. On laser melted surfaces networks of cracks were observed. XRD studies showed that the metastable γ-Al₂O₃ phase present in the SC is transformed to stable α-Al₂O₃ after post treatments. In LM coatings Al₂TiO₅ phase was more predominant in contrast to SC and VA coatings. The microhardness enhancement was observed in case of LM coating compared to the VA and SC. Due to elimination of coating defects in LM samples, there is a considerable reduction in the surface roughness.     

Hot corrosion behavior of detonation gun sprayed Cr3C2–NiCr coatings on Ni and Fe-based superalloys in Na2SO4–60% V2O5 environment at 900 °C

The present work investigates the hot corrosion resistance of detonation gun sprayed (D-gun) Cr₃C₂–NiCr coatings on Superni 75, Superni 718 and Superfer 800 H superalloys. The deposited coatings on these superalloy substrates exhibit nearly uniform, adherent and dense microstructure with porosity less than 0.8%. Thermogravimetry technique is used to study the high temperature hot corrosion behavior of bare and Cr₃C₂–NiCr coated superalloys in molten salt environment (Na₂SO₄–60% V₂O₅) at high temperature 900 °C for 100 cycles. The corrosion products of the detonation gun sprayed Cr₃C₂–NiCr coatings on superalloys are analyzed by using XRD, SEM, and FE-SEM/EDAX to reveal their microstructural and compositional features for elucidating the corrosion mechanisms. It is shown that the Cr₃C₂–NiCr coatings on Ni- and Fe-based superalloy substrates are found to be very effective in decreasing the corrosion rate in the given molten salt environment at 900 °C. Particularly, the coating deposited on Superfer 800 H showed a better hot corrosion protection as compared to Superni 75 and Superni 718. The coatings serve as an effective diffusion barrier to preclude the diffusion of oxygen from the environment into the substrate superalloys. It is concluded that the hot corrosion resistance of the D-gun sprayed Cr₃C₂–NiCr coating is due to the formation of desirable microstructural features such as very low porosity, uniform fine grains, and the flat splat structures in the coating.     

Synthesis and characterization of Al2O3-Ce0.5Zr0.5O2 powders prepared by chemical coprecipitation method

Al₂O₃-Ce_0.5Zr_0.5O₂ catalytic powders were synthesized by the coprecipitation (ACZ-C) and mechanical mixing (ACZ-M) methods, respectively. As-synthesized powders were characterized by XRD, Raman spectroscopy, surface area and thermogravimetric analyses. It was found that the mixing extent of Al³⁺ ions affected the phase development, texture and oxygen storage capacity (OSC) of the Ce_0.5Zr_0.5O₂ powder. Single phase of ACZ-C could be maintained without phase separation and inhibit α-Al₂O₃ formation up to 1200 °C. The specific surface area value of ACZ-C (81.5 m²/g) was larger than that of ACZ-M (62.1 m²/g) and Ce_0.5Zr_0.5O₂ (17.1 m²/g) powders, which were calcined at 1000 °C. In comparison with ACZ-C and Al₂O₃, which were calcined at high temperature (900–1200 °C), it was found that the degradation rate of specific surface area of ACZ-C was lower than that of Al₂O₃. ACZ-C sample showed a higher thermal stability to resist phase separation and crystallite growth, which enhanced the oxygen storage capacity property for Ce_0.5Zr_0.5O₂ powders.     

Al_2O_3/MoS_2复合涂层的制备及摩擦磨损性能

以大气等离子喷涂工艺制备的Al_2O_3陶瓷涂层为模板,利用陶瓷涂层中存在的孔隙和微裂纹,采用水热反应在其内部原位合成具有润滑特性的MoS_2,制备出Al_2O_3/MoS_2的复合涂层。结果表明,通过水热反应在陶瓷涂层原有的微观缺陷中成功合成了MoS_2,合成的MoS_2固体粉末呈类球形状,并且这球状的粉末是由纳米片层状的MoS_2搭建组成的。摩擦试验结果表明,与纯Al_2O_3涂层相比,复合涂层中由于MoS_2润滑膜的形成,其摩擦因数和磨损率都显著降低,且载荷越大,复合涂层的摩擦性能越好。     

Comparison of the structure and wear resistance of Al2O3-13 wt.%TiO2 coatings made by GSP and WSP plasma process with two different powders

The goal of this study is to compare two Atmospheric Plasma Spraying (APS) systems for elaborating alumina/titania coatings with good wear resistance. Both torches used were a common d.c. current Gas-Stabilized Plasma gun (GSP) with argon and hydrogen as plasma forming gases, and a Water-Stabilized high-throughput Plasma gun (WSP) working with water as plasma forming substance. The feedstock were either cladded alumina/titania powder or a mixture of conventional fused and crushed Al₂O₃ powder with agglomerated TiO₂ nanometric particles, the resulting mean size in both cases being about 50 µm. Feedstock material phases were α-alumina and anatase titanium dioxide and the composition of both powders was 13 wt.% of TiO₂ in Al₂O₃. Coatings obtained were analyzed by scanning electron microscopy (SEM). They presented lamellar structures with titania uniformly distributed in the alumina matrix, for both spray techniques. X-ray diffraction showed that anatase phase of titania was converted into rutile phase. The wear resistance tested by slurry abrasion (SAR) has shown that the best coating was that obtained with cladded powder sprayed by GSP process. This finding matched with the highest microhardness of this coating (Vickers indentation). It is worth noting that with these two relatively dissimilar torches similar results were obtained for the wear resistance of alumina-13 wt.% titania coating.     

Synthesis and characterization of Y3Al5O12 and ZrO2-Y2O3 thermal barrier coatings by combustion spray pyrolysis

Y₃Al₅O₁₂ and ZrO₂-Y₂O₃ (8 mol% YSZ) coatings for potential application as thermal barrier coatings were prepared by combustion spray pyrolysis. Thermal cycling of as deposited coatings on stainless steel and FeCrAlY bond coat substrates was carried out at 1000 °C and 1200 °C to determine the thermal fatigue response. Structural and morphological studies on Y₃Al₅O₁₂ and 8 mol% YSZ coatings before and after thermal cycling have been carried out. It has been noted that the coatings on FeCrAlY substrates remain intact after 50 cycles between room temperature and 1200 °C, whereas the coatings on stainless steel show some minor damage such as peeling off near the periphery after 50 cycles at 1000 °C. Thermal diffusivity values of Y₃Al₅O₁₂ and 8 mol% YSZ films were measured by using photo thermal deflection spectroscopy and the values are lower than those of coatings produced by conventional techniques such as EBPVD and APS.     

The effect of plasma spray parameters on the cavitation erosion of Al2O3-TiO2 coatings

This paper reports a study of how the choice of plasma spray parameters, used during deposition of Al₂O₃-13%TiO₂ coatings on carbon steel, influences the cavitation erosion properties of such coatings. The parameters studied are the power feeding rate and hydrogen flow rate. The surface and cross section of coatings before and after cavitation were also observed by scanning electron microscopy (SEM). The phases present in the coatings were characterized by X-ray diffraction method (XRD). The microscopic observations were used to study the inter-lamellar connection, porosity, unmelted particles and so on inside the coating. We also measured the roughness, microhardness, adhesion strength and cavitation erosion of the coatings. The XRD results showed that the coating includes different allotropes of Al₂O₃ such as α and γ. The cavitation erosion studies of the coatings were conducted by ultrasonic cavitation testing on the basis of ASTM G32 standard. It was found that cavitation erosion is accelerated around the unmelted particles and porosities. The results reveal that the cavitation resistance of the coating is determined by its microstructure and that increasing discontinuities (inside the coating) reduce its cavitation resistance. We have found that the coating obtained at hydrogen gas flow rate of 16 L/min and powder feeding rate of 20 g/min has the best cavitation resistance.     

Microstructure and mechanical properties of Al2O3-Cr2O3 composite coatings produced by atmospheric plasma spraying

Al₂O₃, Al₂O₃-Cr₂O₃ and Cr₂O₃ coatings were deposited by atmospheric plasma spraying. Phase composition of powders and as-sprayed coatings was determined by X-ray diffraction. Electron probe microanalyzer was employed to investigate the polished and fractured surface morphologies of the coatings. Mechanical properties including microhardness, fracture toughness and bending strength were evaluated. The results indicate that the addition of Cr₂O₃ is conducive to the stabilization of α-Al₂O₃. Compared with the pure Al₂O₃ and Cr₂O₃ coatings, Al₂O₃-Cr₂O₃ composite coatings show lower porosities and denser structures. Heterogeneous nucleation of α-Al₂O₃ occurs over the isostructural Cr₂O₃ lamellae and partial solid solution of Al₂O₃ and Cr₂O₃ might be occurring as well. Furthermore, grain refining and solid solution strengthening facilitate the mechanical property enhancement of Al₂O₃-Cr₂O₃ composite coatings.     

Preparation and spray drying of Al2O3-TiO2 nanoparticle suspensions to obtain nanostructured coatings by APS

Al₂O₃-TiO₂ coatings were deposited on austenitic stainless steel coupons from nanostructured powders by atmospheric plasma spraying (APS). Commercial suspensions of nanosized Al₂O₃ and TiO₂ particles were used as starting materials. Mixtures of these suspensions and of more concentrated suspensions of Al₂O₃ and TiO₂ were then agglomerated into plasma sprayable feedstock. Agglomeration was performed by spray drying, followed by consolidation thermal treatment.These powders were successfully deposited, yielding coatings that were well bonded to the substrates. The coating microstructure thus consisted of semi-molten feedstock agglomerates surrounded by fully molten particles that acted as binders. Agglomerates from suspensions with higher solids contents yielded coatings with lower porosity and fewer semi-molten areas.     

Characterisation and oxidation of LVOF sprayed Al2O3–40%TiO2 coating on superni 601 and superni 718 superalloys at 800 and 900°C

Failure of components due to high temperature oxidation is the major degradation mechanism in boiler and gas turbine industries. Superalloys having superior mechanical properties and creep resistance are used in these applications but lack resistance to oxidation under aggressive environments. Protective coatings are used to improve their oxidation resistance in such applications. In the present investigation, Al₂O₃–40%TiO₂ coating was deposited on superni 718 and superni 601 superalloys by low velocity oxy fuel process. The as sprayed coating was characterised for microhardness, surface roughness, scanning electron microscopy and X-ray diffraction analysis. High temperature oxidation behaviour of Al₂O₃–40%TiO₂ coated and uncoated superni 718 and superni 601 superalloys has been evaluated at the elevated temperatures of 800 and 900°C for total duration of 50 cycles under cyclic conditions. Each cycle consisted of keeping the samples for 1 h at the elevated temperature followed by 20 min cooling in ambient air. Al₂O₃–40TiO₂ coating in the as sprayed condition showed the presence of Al₂O₃–TiO₂, α-Al₂O₃, TiO₂ as the main phases. Al₂O₃–40%TiO₂ coating on superni 718 and superni 601 superalloys has shown a lower oxidation rate as compared to those of uncoated superalloys. However, the oxidation rate of the coating was not steady due to the occurrence of spallation/sputtering at various stages. The coating was found adherent on the substrate superalloys throughout the study.     

Al2O3-nanodiamond composite coatings with high durability and hydrophobicity prepared by aerosol deposition

We attempted the room-temperature fabrication of Al₂O₃-based nanodiamond (ND) composite coating films on glass substrates by an aerosol deposition (AD) process to improve the anti-scratch and anti-smudge properties of the films. Submicron Al₂O₃ powder capable of fabricating transparent hard coating films was used as a base material for the starting powders, and ND treated by 1H,1H,2H,2H-perfluorooctyltriethoxysilane (PFOTES) was added to the Al₂O₃ to increase the hydrophobicity and anti-wear properties. The ND powder treated by PFOTES was mixed with the Al₂O₃ powder by ball milling to ratios of 0.01 wt.%, 0.03 wt.%, and 0.05 wt.% ND. The water contact angle (CA) of the Al₂O₃-ND composite coating films was increased as the ND ratio increased, and the maximum water CA among all the films was 110°. In contrast to the water CA, the Al₂O₃-ND composite coating films showed low transmittance values of below 50% at a wavelength of 550 nm due to the strong agglomeration of ND. To prevent the agglomeration of ND, the starting powders were mixed by attrition milling. As a result, Al₂O₃-ND composite coating films were produced that showed high transmittance values of close to 80%, even though the starting powder included 1.0 wt.% ND. In addition, the Al₂O₃-ND composite coating films had a high water CA of 109° and superior anti-wear properties compared to those of glass substrates.     

Electrochemical corrosion behavior of plasma sprayed Al2O3‐13%TiO2 coatings in aqueous hydrochloric acid solution

One kind of conventional and two kinds of nanostructured Al₂O₃‐13%TiO₂ coatings were prepared by plasma spray process. The phase composition and microstructure of coatings were examined by means of scanning electron microscopy (SEM) and X‐ray diffraction (XRD). The potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) were used to investigate the corrosion behavior of coatings in aqueous hydrochloric acid solution. The results showed that nanostructured coatings had superior corrosion resistance compared to conventional Metco 130 coating. The corrosion resistance of coatings was mainly related to their microstructure and defects density. The EIS measurement for long time immersion in hydrochloric acid solution revealed that the corrosion resistance of coatings decreased with the increasing of immersion time. During the immersion period, electrochemical corrosion mainly occurred on the carbon steel substrate under NiCrAl coatings. In addition, the Al₂O₃‐13%TiO₂ coatings were also failed during corrosion in aqueous hydrochloric acid solution.