Conventional Electronic Structure of MgB2 and ZrB2: LDA vs. de Haas-v. Alphen & ARPES Data

We compare full potential LDA band calculations of the Fermi surfaces areas and band masses of MgB₂ and ZrB₂ previously reported and new dHvA data. Discrepancies in areas in MgB₂ can be removed by a small shift of bands relative to bands. Comparison of effective masses lead to orbit averaged el-ph coupling constants =1.3 and =0.5, whereas for ZrB₂ only weak el-ph coupling with <0.3 is found. The ARPES data can be also well described by the LDA showing the presence of surface states.     

Effect of magnesium content on the stress exponent and effective stress in the steady state creep of Al-Mg alloys

The stress exponent of steady state creep,n, and the internal ( _i) and effective stresses ( _e) have been determined using the strain transient dip test for a series of polycrystalline Al-Mg alloys creep tested at 300° C and compared with previously published data. The internal or dislocation back stress, _i, varied with applied stress,, but was insensitive to magnesium content of the alloy, being represented by the empirical equation _i=1.084 ^1.802. Such an applied stress dependence of _i can be explained by using an equation for _i of the form _i (dislocation density)^1/2 and published values for the stress dependence of dislocation density. Values of the friction stress, _f, derived using the equation _e/=(1–c) (1– _f/), indicate that _f is not dependent on the magnesium content. A constant value of _f can best be rationalized by postulating that the creep dislocation structure is relatively insensitive to the magnesium content of the alloy.On leave from Engineering Materials Department, University of Windsor, Windsor, Ontario N9B 3P4, Canada.     

Underpinning of a simple blunt flaw fracture initiation relation

With the cohesive process zone representation of the micro-mechanistic processes that are associated with fracture as a basis, the author is involved in a wide-ranging research programme, the objective being to extend the fracture mechanics methodology for sharp cracks to blunt flaws, so as to take credit for the blunt flaw geometry. In earlier work, a Mode I fracture initiation relation has been derived, subject to the restriction that the process zone size s is small compared with the flaw depth (length) and any characteristic dimension other than the flaw root radius . The relation gives the critical elastic flaw-tip peak stress _pcr, and has been derived using a two-extremes procedure, whereby the separate, and indeed exact, solutions for small and large s/ values are blended together to give an all-embracing relation that is valid for all s/ values. _pcr is expressed in terms of the process zone material parameters and geometrical parameters but, for a wide range of flaw geometry parameters, _pcr essentially depends on only one geometrical parameter . This paper provides underpinning for the general thrust of the two-extremes procedure by appealing to exact results for the complete spectrum of s/ values from analyses of appropriate Mode III models. Results obtained by applying the two-extremes procedure are shown to be in very good agreement with the exact results.     

Distribution characteristics of mechanical properties and correlation between the respective properties on S35C carbon steel

Mechanical properties of tensile strength, , upper yield stress, _SU, lower yield stress, _SL elongation, , area reduction, , Vickers hardness, H _v, and impact absorbed energy, E, were examined using 50 specimens of S35C carbon steel, which were machined from two bars supplied from the same charged and heat-treated material. Distribution characteristics of these properties are discussed, and the correlation between each pair of them is investigated from a statistical viewpoint. The main conclusions obtained are summarized as follows; distribution characteristics of _B, _SL, , , H _v and E are well approximated by a normal distribution, but those of asu are not approximated as well by this type of distribution. In the latter case, a Weibull distribution is preferable to represent the distribution pattern. No significant correlation was observed between each pair of the above mechanical properties. Consequently, individual properties have the inherent distribution characteristics independent of the other properties.     

AC electrical conductivity of electron beam evaporated Cu-GeO2 thin cermet films

AC electrical properties of 410 nm think 30 at.wt% Cu-70 at.wt% GeO₂ thin films are reported for the frequency range 10⁴ to 10⁶ Hz and temperature range 150 to 425 K. The loss tangent (tan ) and the dielectric loss (/₀) are found to show striking minima around a cut-off frequency 10⁵ Hz. In the lower frequency range (10⁵ Hz), ₁() ^s T ⁿ is obeyed with s (0 to 0.51) increasing as a function of temperature and n (0.10 to 0.14) showing a very weak temperature dependence. In the higher frequency region (10⁵ Hz), ₁() and /₀ increase sharply leading to the quadratic behavior of ₁() with s equal to 2. These processes are discussed by analyzing an equivalent circuit which shows that at lower frequencies, the effects of series resistance in leads and contacts can be neglected, while at higher frequencies such effect give rise to spurious ² dependance for the conductance. A weakly activated AC conductivity and a frequency exponent s that increases with increasing temperature suggest that the low frequency behavior originates from carrier migration by tunneling process.     

Charged defects-controlled conductivity in Ge-ln-Se glasses

The variation of the d.c. electrical conductivity, , with composition and temperature was investigated for glasses of the Ge-In-Se system. The results indicate a decrease in the activation energy for electrical conductivity, E, and an increase in on introduction of indium into Ge-Se glasses. The changes in E and with composition (selenium content in the glasses) are identical for the Ge_x In₅ Se_95–x and Ge_x In₈Se_92–x families. The results have been traced to the conduction controlled by charged defects in these chalcogenide glasses. The changes in E and have been explained by a shift in the Fermi level, being brought by the introduction of indium.     

Ionic and electronic conductivity in some simple lithium salts

The electrical conductivity () and thermoelectric power (S) of Li₃VO₄, Li₃PO₄ and Li₃BO₃ solidified melts are presented in the temperature range from 415 K to the melting point of each solid. The ionic ( _i,) and electronic ( _e) contributions to have been separated over the entire temperature range with the help of a time-dependence study of the d.c. electrical conductivity. Superionic phases in all three solids have been observed below their melting points in which the conductivity is almost purely ionic. The value of the phase transition temperature below which the solid transforms from superionic to normal phase has been obtained. It has been shown that in the normal phase, these solids are mixed conductors. Data for the temperature variations of both _i, and _e are also presented and discussed.     

Experimental study of the boundary between single-phase convection and boiling in underheated cryogenic liquids

The effect of pressure and underheating on the position of the boundary between heat-transfer regimes in liquid helium and hydrogen is investigated.Notation q heat flux - p pressure - =T_s–T underheating - T_s saturation temperature - T temperature of liquid - T=T_wa – T T_s=T_wa – T_s - T_wa temperature of heat-emitting surface - A,a, B, b, C constants - m, n indices - Nu Nusselt number - Ra Rayleigh number - thermal conductivity - coefficient of cubical expansion - kinematic viscosity - g acceleration - standard deviation Indices 01 conditions of convection-boiling transition - 02 conditions of boiling-convection transition Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 42, No. 1, pp. 5–11, January, 1982.     

Absence of Phase-Fluctuation Contribution to the Low-Frequency Optical Conductivity in d-Wave Superconductors at Zero Temperature

The behavior of the low-frequency optical conductivity _reg() in superconducting cuprates is, at the present, an open and interesting issue. In particular, since the zero-temperature and zero-frequency limit of _reg() attains a value much larger than the universal value expected within a self-consistent T-matrix calculation, an intriguing possibility is that the collective mode can also contribute to _reg(). By taking into account the effect of dissipation on the collective mode in a d-wave superconductor, we evaluate the phase-fluctuation contribution to _reg(0) within the formalism of the phase-only action. We show that even though the collective mode contributes to _reg() at finite frequencies, approaching the zero-temperature and zero-frequency regime the corrections at _reg() due to phase fluctuations vanish.     

Photoplastic effects in Cd0.2Hg0.8Te

We irradiated Cd_0.2Hg_0.8Te samples at room temperature in the plastic range, with a CO₂ laser beam the wavelength of which (=10 500 nm) is 20% longer than the absorption threshold. We observed a positive photoplastic effect (PPE) of the order _PPE/4 to 5%.     

Evaluation of the true activation enthalpy of superplastic flow including a threshold stress

A new method is suggested for the evaluation of the true activation enthalpy for alloys where the strain rate of the superplastic flow varies with a power of an effective stress _e = -_o, where and _o are the applied stress and a threshold stress, respectively. Some earlier results concerning superplastic AlMgZnCu alloys containing chromium and in which a strongly temperature-dependent threshold stress can be revealed, are reanalysed. The results are in good agreement with the previous ones. It has been shown further that for the alloys investigated the true activation energy increases with increasing chromium content.     

Tests on a flow cryostat with series cooling

Measurements and calculations on a flow cryostat with serial cooling have given equivalent thermal schemes that have been tested for adequacy and consequent simple working formulas.Notation T_c, T_i, T_w, T_f temperatures of case, body i, tube wall, and flowing coolant in K - T₀ and T_e coolant temperatures at inlet and exit for heat exchanger and pipes in K - T_wi mean pipe wall temperature at points of attachment of bundles from body i in K - T_wn pipe wall temperature at point of attachment for bundle n in K - (_i)_n and _i thermal conductivities of bundle n and all bundles from body i in W/K - _ij thermal conductivity between bodies i and j in W/K - _ci, , _cw thermal conductivities from case to body i and total and radiative conductivities from case to pipe in W/K - _c convective heat-transfer coefficient between pipe and coolant in W/m²·K - _r radiative heat-transfer coefficient between case and pipe in W/m²·K - pipe material thermal conductivity in W/m·K - c specific heat of helium at constant pressure in J/kg·K - q and q_r correspondingly densities of the total heat flux and radiative flux to the pipe in W/m² - P_r heat flux along bundle r in W - M coolant mass flow rate in kg/sec - F tube cross section area in m² - S_i and S_o inside and outside surface areas of pipe in m² - L pipe length in m - ¯x=x/L relative coordinate along pipe axis - ¯x_r relative coordinate for bundle r attachment - R total number of bundles - N_i number of bundles cooling body i - J_i number of bodies linked by heat bridges to body i - _i relative error in calculating the temperature of body i by comparison with numerical result in % - _w mean relative error in heat exchanger temperature calculated numerically by comparison with temperature from (4) taken at ten equally separated points in % - (¯x-¯x_r) Dirac function Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 56, No. 5, pp. 760–767, May, 1989.     

Examining the temperature dependence of the mechanical properties for materials in large-diameter tubes

Measurements have been made on the mechanical properties of largediameter tubes made of 09G2S, 14G2SAF, and 17G1S steels and on welded joints in them at strain rates of 200 sec^–1 and 113–293 K. Fivefold microspecimens 1.2 mm in diameter have been employed. The parameters have been determined in the temperature-rate dependence of the Yaroshevich yield point, lower brittleness temperature, and fracture resistance as affected by the ferrite diameter. A method is proposed for predicting the brittleness range from the dependence of the notch bottom narrowing B on the generalized parameter = S_f/_y — _t/_i for a Menaget specimen.Translated from Problemy Prochnosti, No. 4, pp. 43–50, April, 1994.     

Statistical analysis of the Hertzian fracture of pyrex glass using the Weibull distribution function

Hertzian fracture tests were carried out on specimens of ground-and-polished Pyrex glass using polished Pyrex glass balls of 6 and 8 mm diameter. The results were analysed according to the theory of flaw statistics originally proposed by Weibull. The Weibull parameters m and ₀ were found to be independent of ball size; _u however decreased with increase in ball size. The parameters _u,₀ and m obtained from the Hertzian tests differed from those obtained from a four-point bend test. The predicted mean fracture stress and the mean fracture location for Hertzian fracture using the derived Weibull parameters agreed reasonably well with the experimental values.     

Ageing characteristics of Al-2.5% Li rapidly solidified alloy

The present work was performed on an Al–2.5 wt% Li alloy produced by melt spinning. The ribbons were aged in the temperature range 180 to 310° C for times between 1 min and 120h. The kinetics of coarsening of (Al₃Li) and (AlLi) phase particles were investigated using transmission electron microscopy and hardness measurements. The results show that coarsening of (Al₃Li) follows a simple linear relation with the cube root of Me, whereas coarsening of (AlLi) does not follow the same trend. We believe that the (AlLi) phase nucleates at the (Al₃Li)/matrix interface and grows by the dissolution of the nearby (Al₃Li) particles. The mechanical properties of the powder metallurgy alloy show that a large volume fraction of PFZ contributes to the alloy ductility, 11 %, in the aged condition. Also, the yield strength is greatly improved due to refinement effects enhanced by rapid solidification.     

Application of a new iterative method for elastic-plastic stress analysis

A new iterative method for elastic-plastic stress analysis based on a new approximation of the constitutive equations is proposed and compared with standard methods on the accuracy and the computational time in a test problem. The proposed method appears to be better than the conventional methods on the accuracy and comparable with others on the computational time. Also the present method is applied to a crack problem and the results are compared with experimental ones. The agreement of both results are satisfactory.List of symbols u = (u ₁, u ₂) displacements u ^(H) = u ⁽ⁿ⁺¹⁾ - u ⁽ⁿ⁾ u _k ⁽ⁿ⁾ = u _(k ^{(n + 1)} - u ⁽ⁿ⁾ (n, k = 0, 1, 2, ...) - = ₁₁, ₂₂, ₁₂) stresses - = (₁₁, ₂₂, ₁₂) strains - = (₁₁, ₂₂, ₁₂) center of yield surface - D elastic coeffficient matrix, C = D ^–1 - von Mises yield function. The initial yielding is given by f() = _Y - f {f/} - ^* transposed f - H hardening parameter (assumed to be a positive constant for kinematic hardening problems) - time derivative of - [K] total elastic stiffness matrix - T traction vector - = [B] relation between nodal displacements and strains     

Pyramidal yield criteria for epoxides

The tensile, compressive and shear yield strengths of two epoxides were measured under superposed hydrostatic pressure extending to 300 MN m^–2. For both materials, the ratio of the moduli of the tensile, _T, to compressive, _C, yield stress at atmospheric pressure was approximately 34, as has been reported previously for a number of thermoplastics. The ₂= ₃ envelope in stress space was plotted according to these two-parameter ( _C and _T) yield criteria: conical, paraboloidal and pyramidal; the best correlation was with the last. The experimental tensile and compressive data for tests under pressure, however, fit slightly better two straight lines which are consistent with a three-parameter single hexagonal pyramidal yield surface. For plane stress and shear under pressure yield envelopes of these surfaces, the correlation with experimental data is again best for the pyramidal criteria, except for biaxial or triaxial tension when these resins are brittle. The third independent parameter employed in the pyramidal criterion was the equi-biaxial compressive yield stress, determined by tensile experiments under appropriate superposed hydrostatic pressure; alternatively plane strain compressive yield stress, _PC, may be used.     

Direct and inverse heat-conduction problems for a semiinfinite rod for a partial outflow of heat through the surface

Analytical solutions of the direct and inverse problems of nonstationary heat conduction in a thin semiinfinite rod are given for the case of radiative heat fluxes at the lateral surfaces and a partial outflow of heat by convection and radiation through the end of the rod.Notation thermal diffusivity - x₁ coordinate along the length of the rod - t₁ time - t=t₁/d² dimensionless time (Fourier number) - x=X₁/d relative coordinate - T_o initial temperature - Boltzmann constant - Sk=aT_c ³d/ Stark number - Bi=d/ reduced Biot number - emissivity Translated from Inzhenero-Fizicheskii Zhurnal, Vol. 47, No. 1, pp. 148–153, July, 1984.     

Radiation of internal waves during vertical motion of a body through a nonuniform liquid

Energy losses to radiation of internal waves during the vertical motion of a point dipole in two-dimensional and three-dimensional cases are computed.Notation _o(z), p_o(z) density and pressure of the ground state - z vertical coordinate - v, p, perturbed velocity, pressure, and density - H(d 1n _o/dz)^–1 characteristic length scale for stratification - N=(gH^–1–g²c _o ^–2 )^1/2 Weisel-Brent frequency - g acceleration of gravity - c_o speed of sound - vertical component of the perturbed velocity - V vector operator - k wave vector - frequency - d vector surface element - W magnitude of the energy losses - (t), (r) (x)(y)(z) Dirac functions - v_o velocity of motion of the source of perturbations - d dipole moment of the doublet - _o,l length dimension parameters - _o intensity of the source Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 39, No. 4, pp. 619–623, October, 1980.     

Some simple flows of a Johnson-Segalman fluid

Summary Unlike most other fluid models, the Johnson-Segalman fluid allows for a non-monotonic relationship between the shear stress and rate of shear in a simple shear flow for certain values of the material parameter. This has been used for explaining a phenomenon such as spurt. Here, we study three simple flows of a Johnson-Segalman fluid with a view towards understanding its response characteristics. We find that boundary conditions can have a very interesting effect on the regularity of the solution; changing them continuously leads to solutions that change their regularity. First, we consider the flow through a circular pipe and find solutions that have discontinuous velocity profiles which have been used to explain the phenomenon of spurt (cf. [10], [11]). Second, we consider the flow past an infinite porous plate and show that it will not admit solutions which have discontinuous velocity gradients, the solutions being necessarity smooth. Lastly, we study Poiseuille flow in a concentric annulus with porous boundaries. While spurt could be explained alternatively by allowing for stick-slip at the wall, the Johnson-Segalman model seems particularly suited in describing the appearance of shear-layers (cf. [13]).