石墨/碳化硅/铁氧体涂层复合材料性能研究

为了开发具备良好介电性能和力学性能的多功能吸波复合材料,以涤纶针织物为基布,以环氧树脂为基体,在基布上进行石墨/碳化硅/铁氧体三层复合涂层整理,制备1.5 mm涂层厚度的柔性纺织涂层复合材料.采用介电谱仪研究了吸波剂的含量对吸波涂层材料介电常数和损耗角正切的影响.鉴于该材料多用于工程领域,采用万能材料实验机测试了该复合材料的拉伸、弯曲、剪切等力学性能.结果表明,该复合材料在低频段具备良好的介电性能,且具备一定的力学性能.     

Hybrid composites made of carbon and glass woven fabrics under quasi-static loading

Experimental studies are presented on in-plane mechanical properties for two types of hybrid composites made using 8H satin weave T300 carbon fabrics and plain weave E-glass fabrics with epoxy resin. Results are also presented for 8H satin weave T300 carbon/epoxy and plain weave E-glass/epoxy. Studies are carried out under both tensile and compressive in-plane quasi-static loading. It is observed that for hybrid composites, placing glass fabric layers in the exterior and carbon fabric layers in the interior gives higher tensile strength and ultimate tensile strain than placing carbon fabric layers in the exterior and glass fabric layers in the interior. Quantitative data is given for different mechanical properties.     

滑石粉涂层复合材料的制备及其介电性能和电导率

以玻璃纤维膨体纱织物为基材,以环氧树脂E44为粘着剂,650低分子量聚酰胺为固化剂,以价格低廉、密度较小的滑石粉为吸波材料,制备了滑石粉涂层复合材料。重点探讨了滑石粉含量及涂层厚度对介电常数和电导率的影响。结果表明制备的滑石粉涂层复合材料具备良好的介电性能。在研究的频率范围内,滑石粉的含量、涂层厚度对复合材料的介电常数实部和虚部、损耗角正切值、电导率的实部和虚部影响较大。     

Voids and their effect on the strain rate dependent material properties and fatigue behaviour of non-crimp fabric composites materials

The manufacture of composite structures is inevitably linked to the formation of voids. Several non-destructive techniques are potentially able of detecting defects, but just the exact knowledge of the effects of defects on the mechanical properties allows the definition of thresholds for the purpose of quality management. In this paper an experimental program for characterizing the effect of voids on the composite materials behaviour is presented. Therefore glass fibre non-crimp fabric reinforced epoxy composites were produced using vacuum assistant resin transfer moulding. For obtaining various void contents specially modified process parameters were used. Nominally defect free specimens are compared with flawed specimens. Tensile testing at different loading speeds and fatigue tests in tension-compression loading are performed.     

空心玻璃微珠增强环氧树脂复合材料的动态力学性能

通过对空心玻璃微珠（HGM）/环氧树脂复合材料进行动态力学分析（DMA）,给出了环氧树脂基体在不同频率下的动态力学温度谱,利用时温等效原理,根据位移因子构建了HGM/环氧树脂复合材料在室温下的储能模量和损耗模量的频率主曲线。分析了温度和频率、体积比和粒径对HGM/环氧树脂复合材料储能模量和损耗模量的影响规律,并结合SEM图像分析其影响机制。结果表明,随着HGM体积分数的增加,HGM/环氧树脂复合材料储能模量和损耗模量呈增大趋势;储能模量随温度升高而降低,损耗模量随温度的增加先增大后减小,在玻璃化温度附近形成一个峰值,HGM低于10%的配比有利于提高其动态力学性能。颗粒的团聚及界面的黏合均对HGM/环氧树脂复合材料的动态力学性能产生较大影响。     

The effect of thermoplastic coating on the mechanical properties of woven fabric carbon/epoxy composites

The effect of a polyetherimide (PEI) coating on the mechanical properties of woven fabric carbon/epoxy composites was investigated by thermal mechanical analysis, fractographical analysis and mechanical properties measurements. PEI coating enhanced the mechanical properties of carbon/epoxy composites mainly through the improvement of matrix properties. This was because most of the PEI coated on the carbon fiber diffused into the bulk of epoxy matrix due to its good miscibility with epoxy resin. As for mechanical properties of woven fabric carbon/epoxy composites, the extent of improvement by PEI coating highly depended on the applied stress state. Among the mechanical properties, mode II delamination resistance of carbon/epoxy composites showed the highest increment because matrix shear property played an important role in delamination resistance of woven fabric carbon/epoxy composite. Because of the woven geometry of carbon fiber, the improvement in impact property of carbon/epoxy composite was trivial except the large amount of PEI coated case.     

玻璃纤维立体织物增强环氧树脂泡沫夹层复合材料的制备及力学性能

为了进一步提高泡沫夹层复合材料的承载能力和综合性能,实现其在轨道交通及汽车等工业领域的应用,开展了玻璃纤维立体织物增强环氧树脂泡沫(GF-Fabric/EP)复合材料的制备及其力学性能的研究。制备GF-Fabric/EP复合材料及其夹层结构,探索了GF-Fabric/EP复合材料及其夹层结构的失效行为,以揭示立体织物的增强机制。结果表明：立体织物的引入可显著改善GF-Fabric/EP复合材料的强度、刚度及破坏应变;但在不同承载条件下,各纱线发挥承载作用和效果不同。面板、芯材各自的性能、尺寸及面/芯界面性能均是影响GF-Fabric/EP夹层复合材料力学性能及失效特征的重要因素。以三点加载下的弯曲性能为例,针对不同的GF-Fabric/EP夹层复合材料,需调整跨厚比和试样尺寸并获得理想的失效特征,方可对其弯曲性能或层间剪切性能进行有效、合理的评价。     

超细玻璃粉增强环氧树脂的研究

研究了玻璃粉/环氧树脂封接复合材料的制备与性能.利用激光粒度分析仪、电子多功能实验机、SEM、热分析仪等测试粉料粒径、结构形貌以及机械强度等性能.结果表明,在玻璃粉的制备过程中,加入适量的活性剂(硬脂酸盐),可以大大降低玻璃粉的粒径和粒径分布范围.将超细玻璃粉用偶联剂处理后,与环氧树脂混合制备成封接复合材料,比环氧树脂具有更好的力学性能和热稳定性.     

Effect of UV and water spraying on the mechanical properties of flax fabric reinforced polymer composites used for civil engineering applications

The lack of data related to durability is one major challenge that needed to be addressed prior to the widespread acceptance of natural fibre reinforced polymer composites for engineering applications. In this work, the combined effect of ultraviolet (UV) radiation and water spraying on the mechanical properties of flax fabric reinforced epoxy composite was investigated to assess the durability performance of this composite used for civil engineering applications. Specimens fabricated by hand lay-up process were exposed in an accelerated weathering chamber for 1500 h. Tensile and three-point bending tests were performed to evaluate the mechanical properties. Scanning electron microscope (SEM) was used to analyse the microstructures of the composites. In addition, the durability performance of flax/epoxy composite was compared with synthetic (glass and carbon) and hybrid fibre reinforced composites. The test results show that the tensile strength/modulus of the weathered composites decreased 29.9% and 34.9%, respectively. The flexural strength/modulus reduced 10.0% and 10.2%, respectively. SEM study confirmed the degradation in fibre/matrix interfacial bonding after exposure. Comparisons with other composites implies that flax fabric/epoxy composite has potential to be used for civil engineering applications when taking its structural and durability performance into account. Proper treatments to enhance its durability performance will make it more comparable to synthetic fibre reinforced composites when considering as construction building materials.     

碳纤维增强羟基磷灰石/环氧树脂复合材料的制备与力学性能

采用树脂传递模塑(RTM)工艺制备了碳纤维增强环氧树脂以及碳纤维增强羟基磷灰石(HA)/环氧树脂两种复合材料，并测试了其力学性能。结果表明，RTM工艺可以基本保证环氧基体均匀浸入碳纤维织物内部。碳纤维增强HA，环氧复合材料的冲击韧性高于碳纤维增强环氧复合材料，而弯曲强度和弯曲模量低于碳纤维增强环氧复合材料。两种复合材料的弯曲强度远高于人体皮质骨，弯曲模量与皮质骨非常接近。动态力学分析(DMA)表明加入HA后，复合材料的贮存模量和内耗降低，玻璃化转变温度升高。     

激光改性纤维对其增强环氧树脂复合材料力学性能的影响

利用激光对玻璃纤维、玄武岩纤维和碳纤维进行表面改性后,以环氧树脂为基体,分别制备三种纤维增强环氧树脂复合材料。利用SEM和万能试验机对表面改性前后的碳纤维形态、力学性能及三种纤维/环氧树脂复合材料的力学性能和断面形貌进行表征,研究了纤维激光表面改性对三种纤维及其增强环氧树脂复合材料力学性能的影响。结果表明:激光表面改性对碳纤维/环氧树脂复合材料的力学性能提升最高,其拉伸强度最大提高了77.06%,冲击强度最大提高了31.25%,玄武岩纤维/环氧树脂复合材料的力学性能提升次之,而玻璃纤维/环氧树脂复合材料的力学性能有所下降。因此,激光进行表面改性适用于碳纤维和玄武岩纤维。     

Hybrid multi-scale composites developed from glass microfiber fabrics and nano-epoxy resins containing electrospun glass nanofibers

In this study, hybrid multi-scale composites were developed from glass microfiber fabrics (GFs) and nano-epoxy resins containing electrospun glass nanofibers (EGNFs). The hypothesis was that, through dispersing a small amount of EGNFs into epoxy resin, mechanical properties (particularly out-of-plane mechanical properties) of the resulting hybrid multi-scale composites would be significantly improved. The composites were fabricated by the technique of vacuum assisted resin transfer molding (VARTM). The interlaminar shear strength, flexural properties, impact absorption energy, and tensile properties of the composites were evaluated, and the results were compared to those acquired from GFs/epoxy composite as well as GFs/epoxy composites containing chopped glass microfibers (GMFs); additionally, the reinforcement and/or toughening mechanisms were investigated. The study revealed that the nano-epoxy resin with 0.25 wt.% of EGNFs resulted in substantial improvements on mechanical properties of the resulting hybrid multi-scale composites.     

Evaluation of the mechanical behavior of epoxy composite reinforced with Kevlar plain fabric and glass/Kevlar hybrid fabric

In this study, composite plates were manufactured by hand lay-up process with epoxy matrix (DGEBA) reinforced with Kevlar fiber plain fabric and Kevlar/glass hybrid fabric, using to an innovative architecture. Results of the mechanical properties of composites were obtained by tensile, bending and impact tests. These tests were performed in the parallel direction or fill directions of the warp and in a 90° direction. FTIR was used in order to verify the minimum curing time of the resin to perform the mechanical tests, and scanning electron microscopy was used to observe reinforcement and matrix fractures. Composites with Kevlar/glass hybrid structure in the reinforcing fabric showed the better results with respect to specific mechanical strength, as well as bending and impact energy.     

磨碎玻璃纤维增强环氧树脂复合材料的制备及力学性能研究

用硅烷偶联剂对磨碎玻璃纤维表面进行改性,并制备玻璃纤维/环氧树脂复合材料,采用超声分散对复合材料分散处理,探讨不同磨碎玻璃纤维粉质量比对环氧树脂基复合材料压缩、拉伸性能的影响。研究表明,添加磨碎玻璃纤维后,环氧树脂的强度和硬度显著增强。当磨碎玻璃纤维掺量在15%~25%之间时,复合材料的综合力学性能最好,其压缩强度、压缩模量、拉伸强度最高达到67.1 MPa、1.68 GPa、57.6 MPa,与纯环氧树脂相比提高了24%、35%、34%;断裂伸长率随着掺量的增加逐渐降低,当含量达到30%时比纯环氧树脂的降低了48%,表明添加玻璃纤维粉后环氧树脂脆性增强。目数小粒径较大的玻璃纤维粉对环氧树脂力学性能增强效果更优,但影响程度不如含量对复合材料力学性能的影响大。     

纬编双轴向织物/环氧树脂电加热复合材料电热及层间剪切性能

为开发一种可用于航空飞行器防/除冰防护的电加热复合材料,本文设计制备了三种纬编双轴向织物/环氧树脂复合材料,采用实验方法研究了纬编双轴向织物电阻丝排列密度对复合材料电热性能和层间剪切性能的影响。电加热复合材料上、下层均为玻璃纤维/环氧树脂预浸料,中间层为电加热纬编双轴向织物,织物衬经纱、捆绑纱和衬纬纱分别采用铜镍合金丝、涤纶和玻璃纤维。采用红外温度测试仪和材料万能试验机进行性能测试。结果表明:施加电压6 s后复合材料表面温度快速升高,在60 s左右温度达到最高平衡温度,复合材料表面最高平衡温度与施加电压成正比关系;当施加电压不变时,电阻丝排列密度越小,复合材料表面最高平衡温度越高;电阻丝排列密度越小,复合材料层间剪切强度越大。可见,纬编双轴向织物/环氧树脂电加热复合材料具有轻质高强、加热速率高、成型性好等特点,适合用于飞行器多个部位的防/除冰。      

纳米SiO_2改性环氧树脂复合材料的低温力学性能研究

对环氧树脂/纳米SiO2复合材料的低温力学性能进行了研究.在环氧树脂中加入SiO2形成复合材料,并采用对纳米颗粒表面进行硅烷偶联处理的方法实现了SiO2纳米粒子在树脂基体中的均匀分散.在液氮下对一部分复合材料进行冷冻,然后通过电子万能实验机和冲击实验机测试其低温力学性能,并与未冷冻的复合材料的室温力学性能进行比较.结果表明,复合材料低温下的拉伸强度比室温下的高,但冲击强度和断裂伸长率有所下降.     

湿热老化对玻璃纤维/环氧树脂复合材料性能的影响

为研究玻璃纤维(GF)/环氧树脂复合材料湿热老化机制, 首先, 利用称重法、动态热机械分析仪(DMA)、SEM和矢量网络介电分析仪研究了湿热老化对GF/环氧树脂608(EP608)复合材料性能的影响;然后, 分析了复合材料的吸湿率、力学性能、介电性能与老化时间的关系, 并对其老化机制进行了探讨。结果表明:随老化时间延长, GF/EP608复合材料的力学性能和介电性能均有不同程度的下降;湿热老化对GF/EP608复合材料吸湿率的影响符合Fickian扩散定律;树脂基体的塑化、水解和基体-纤维界面的破坏是造成GF/EP608复合材料力学性能和介电性能下降的主要因素。所得结论可为GF增强环氧树脂基复合材料的应用提供科学依据。      

Application of Interlaminar Tests to Marine Composites. Relation between Glass Fibre/Polymer Interfaces and Interlaminar Properties of Marine Composites

The need for improved performance and the development of new composite manufacturing methods require a better understanding of the role of interface phenomena in the mechanical behaviour of these materials. The influence of the cure cycle on the bulk and surface properties of the matrix resin, and of composites based on polyester and epoxy resins reinforced with glass fibres has been studied. While the mechanical properties of the epoxy vary with cure temperature the surface tension is not affected. The increase in interfacial shear strength and interlaminar shear strength with increased cure temperature cannot be simply explained by the wetting of the fibres by the matrix. The importance of thermal stresses, generated at the interface by resin shrinkage and differences in thermal expansion, for the mechanical behaviour of the composite are demonstrated.     

高强玻纤增强ABS复合材料的制备及性能

以丙烯腈-丁二烯-苯乙烯共聚物(ABS)及玻璃纤维(GF)为原料,以苯乙烯-马来酸酐共聚物(SMA)和环氧树脂(E-poxyresin)作为界面相容剂,研究了界面相容剂对玻璃纤维增强ABS复合材料力学性能及界面粘接的影响。结果表明,加入SMA或环氧树脂,玻纤增强ABS复合材料的力学性能明显提高;SMA与环氧树脂复配有明显的协同效果,同时加入SMA和环氧树脂后的复合材料的性能更加优越,界面粘接性能得到很大的改善,在玻纤加入量为30%时,其拉伸强度、弯曲强度、冲击强度较未添加界面相容剂时分别提高了44%、29%、100%。     

Improved adhesion between nickel–titanium SMA and polymer matrix via acid treatment and nano-silica particles coating

Shape memory alloy (SMA) composites are the desirable candidate for smart materials that used in intelligent structures. However, the overall mechanical performance of SMA composites depends immensely on the quality of the interaction between SMA and polymer matrix. Therefore, it is necessary to find out an approach to enhance the interfacial property of this composite. In this paper, we modified nickel–titanium SMA wire with nano-silica particles before and after acid treatment. The modification effect on the interfacial strength between SMA and epoxy resin was evaluated. Contact angle analysis, scanning electron microscopy (SEM) observation, and single fiber pull-out test were carried out. The bonding characteristics between modified wire and liquid/cured resin were investigated. We then embedded SMA wire into woven glass fabric/epoxy composite laminates, and manufactured this hybrid composites via vacuum assisted resin transfer molding processing. Three-point-bending test of the hybrid composites was performed to validate the modification effect. Fiber pull-out experiment demonstrates that the interfacial shear strength increases by 6.48% by nano-silica particles coating, while it increases by 52.21% after 8 h acid treatment and nano-silica particles coating simultaneously. For hybrid composites, flexural strength of the two specimens increases by 19.8 and 48.2%, respectively. In SEM observation, we observed large debonding region in unmodified composites, while interfacial adhesion between modified wire and epoxy keeps strong after flexural damage.