对二甲苯和醋酸二元液体混合物在不同温度下的超额摩尔体积、粘度和热容

Experimental densities, viscosities and heat capacities at different temperatures were presented over the entire range of mole fraction for the binary mixture of p-xylene and acetic acid. Density values were used in the determination of excess molar volumes, VE. At the same time, the excess viscosity and excess molar heat capacities were calculated. The values of V^E, η^E and cE/p were fitted to the Redlich-Kister equation. Good agreements were observed. The excess molar volumes are positive with a large maximum value located in the central concentrationrange. The excess viscosity has an opposite trend to the excess molar volume V^E. η^E values are negative over the entire range of the mixture. The cure of dependence of c E/p on concentration has a special shape. The molecularinteraction between v-xvlene and acetic acid is discussed.     

乙酸乙酯-1,2-丙二醇二元系的密度、折射率和黏度

常压下测定了乙酸乙酯和1,2-丙二醇二元系在298.15～323.15 K下的密度、折射率和黏度,建立了混合液密度、黏度随组成和温度变化关系的方程。计算了过量摩尔体积V^E,折射率偏差Δn_D,黏度偏差Δη和过量流动活化自由能ΔG^*E。结果表明,过量摩尔体积低温时在全浓度范围内为负值,但随温度升高,在富酯区变为正值;而折射率偏差高温时在富醇区为微小正值,其他情况都是负值;黏度偏差和过量流动活化自由能显示了相同的变化关系,均为负值,且都随温度降低而偏差增大。     

1,3-丙二醇与水、乙醇二元混合体系超额体积

测定了常压下1,3-丙二醇-水和1,3-丙二醇-乙醇两个二元混合体系纯组分及混合液在328.15～348.15 K温度内全浓度范围的密度,计算了体系的超额摩尔体积等性质。两个二元混合体系的超额摩尔体积在所测定的温度和全浓度范围内均呈负偏差。体积数据说明1,3-丙二醇-水、乙醇混合体系中不同分子间的交叉缔合强于同分子间的自缔合,同时组分间分子大小的不对称产生填充效应。     

2-甲基-1,3-丙二醇水溶液密度和粘度的测定及关联

常压下采用密度瓶测定了纯液体2-甲基-1,3-丙二醇(MPO)及不同浓度的MPO 水二元体系在298.15~367.15K范围的密度;用乌氏粘度计测定了纯液体MPO及该二元体系在相应温度下的粘度.结果表明:MPO及其水溶液的密度和粘度均随温度升高而减小,密度呈线性衰减,粘度呈指数衰减;一定温度下MPO 水二元体系的密度随浓度变化大约在70%处出现了一极大值. 同时分别由密度和粘度实验数据计算了不同温度及组成下该二元体系的超额摩尔体积V E和混合粘度变化△η,结果V E和△η均为负值, 说明产生了负偏差.并由实验数据拟合出Grunberg-Nissan模型中的MPO-水体系的二元交互参数△Gij,它与温度和组成均有关.     

2-甲基-3-丁烯-2-醇+直链一元醇二元体系的过量摩尔体积和表观摩尔体积298.15 K)

Excess molar volumes (Vm^E) of binary mixtures of 2-methyl-3-buten-2-ol[CH3C(OH)(CH3)CHCH2] with four 1-alcohols:methanol,ethanol,1-propanol and 1-butanol at 298.15K and atmospheric pressure are derived from density measurements with a vibrating-tube densimeter.All the excess volumes are negative in the systems over the entire composition range. The results are correlated with the Redlich-Kister equation.The effects of chain length of 1-alcohols on Vm^E are discussed.The apparent molar volumes of 2-methyl-3-buten-2-ol and 1-alcohols are calculated respectively.     

强缔合体系醋酸-水溶液密度和粘度测定及关联

测定了醋酸水二元体系常压下在298.15—363.15K时的密度和粘度数据,由密度数据计算出超额体积VE的值,并用Redlich Kister方程进行了回归;同时对粘度的数据也按超额性质的方法进行了处理,求出了不同温度不同组成下的ηE值。数据处理过程中发现,ηE/(x1x2)随组成没有变化,在不同温度下为一常数,根据这一特殊现象,建立了由纯物质的粘度数据来计算醋酸水体系在任意温度和组成下的粘度数据,并把所得粘度的计算值和实验值进行比较,120个数据点的平均相对误差为1.1%,结果比较满意。     

1,2-环己二醇的焓和热容数据研究

The thermodynamic properties of different geometric structures of 1,2-cyclohexanediol which were rarely reported in literature, such as combustion enthalpy, formation enthalpy, melting enthalpy and heat ca-pacities, were determined by NETZSCH DSC 204 Scanning Calorimeter. The relationship between the melting point and the composition for the mixture system of cis-1,2-cyclohexanediol and trans-1,2-cyclohexanediol was investigated and corresponding phase diagram was obtained. \"The melting enthalpies of both cis-1,2-cyclohexanediol and trans-1,2-cyclohexanediol are 20.265kJ·mol-1 and 16.368kJ·mol-1 respectively. The standard combustion enthalpies of cia- and trans-1,2-cyclohexaneddiol were determined by calorimeter. They are respec-tively -3507.043 kJ·mol-1 and - 3497.8 kJ·mol-1 at 298.15 K.The standard formation enthalpies are respectively 568.997 kJ·mol-1 and 578.240 kJ·mol-1 for cia- and trans -1,2-cyclohexaneddiol.     

离子液体[BPy]BF4和甲醇二元混合体系的超额摩尔体积、折射率和黏度

合成了室温离子液体N-丁基吡啶四氟硼酸盐([BPy]BF4),通过核磁共振1H-NMR和红外光谱IR对其结构进行了表征.在298.15 K和常压下,采用U形振荡管密度计测定[BPy]BF4-甲醇体系的密度;用阿贝尔折射仪测定了该二元混合体系在相同温度和压力下的折射率;用乌氏黏度计测定了该二元混合体系在相同温度和压力下的...     

甘油氢解制备1,2-丙二醇和1,3-丙二醇催化剂研究进展

随着生物质甘油下游综合利用研究的兴起,甘油氢解反应已成为研究热点。甘油氢解反应工艺的关键技术是氢解催化剂,对近年来甘油氢解制备1,2-丙二醇和1,3-丙二醇的催化剂研究进展进行综述。通过分析甘油氢解制备1,2-丙二醇和1,3-丙二醇催化剂的组成和工业应用情况,对未来可能实现工业化的催化剂体系前景进行展望。     

环己酮-环己烷混合液密度和粘度的测定及关联

在常压下分别测定了环己酮与环己烷的混合液在293,15～343．15K下的密度和粘度,并由密度数据计算出超额体积V^E、由粘度数据计算出了不同温度和组成下的超额粘度△η,V^e为正值,△η为负值;同时对不同温度下的超额体积、超额粘度与组成的关系分别用Redlich—Kister方程进行了关联,最大标准偏差小于3％,说明此体系适合采用Redlich—Kister方程回归。混合溶液的粘度随温度的关系用Andrade公式进行了关联,各组成关联的相关系数接近于1。     

Excess Molar Volume, Viscosity and Heat Capacity for the Binary Mixture of p-Xylene and Acetic Acid at Different Temperatures

Experimental densities, viscosities and heat capacities at different temperatures were presented over the entire range of mole fraction for the binary mixture of p-xylene and acetic acid. Density values were used in the determination of excess molar volumes, VE. At the same time, the excess viscosity and excess molar heat capacities were calculated. The values of VE, ηE and cpE were fitted to the Redlich-Kister equation. Good agreements were observed. The excess molar volumes are positive with a large maximum value located in the central concentration range. The excess viscosity has an opposite trend to the excess molar volume VE. ηE values are negative over the entire range of the mixture. The cure of dependence of cpE on concentration has a special shape. The molecular interaction between p-xylene and acetic acid is discussed.     

二元混合物环丁酚和对二甲苯、乙苯在温度范围为303.15—353.15K下的密度、黏度及其相关性质

Densities and viscosities of the binary systems of sulfolane ＋ ethylbenzene, sulfolane ＋ p-xylene have been experimentally determined in temperature interval 303.15—353.15 K and at atmospheric pressure for the whole composition range. The excess molar volumes and viscosity deviations were computed. The computed quantities have been fitted to Redlich-Kister equation. Excess molar volumes and viscosity deviation show a systematic change with increasing temperature. Two mixtures exhibit negative excess volumes with a minimum which occurs approximately at χ = 0.5. The effect of the size, shape and interaction of components on excess molar volumes and viscosity deviations is discussed.     

二元混合物环丁酚和对二甲苯、乙苯在温度范围为303.15-353.15K下的密度、黏度及其相关性质

Densities and viscosities of the binary systems of sulfolane ethylbenzene, sulfolane p-xylene have been experimentally determined in temperature interval 303.15-353.15 K and at atmospheric pressure for the whole composition range. The excess molar volumes and viscosity deviations were computed. The computed quantities have been fitted to Redlich-Kister equation. Excess molar volumes and viscosity deviation show a systematic change with increasing temperature. Two mixtures exhibit negative excess volumes with a minimum which occurs approximately at x = 0.5. The effect of the size, shape and interaction of components on excess molar volumes and viscosity deviations is discussed.     

二甲苯与环丁砜混合液粘度和密度测定及关联

在常压下采用U形振动管密度计测定了对二甲苯与环丁砜的混合液在298 15K～353 15K下的密度,用乌氏粘度计测定了此混合溶液在303 15K～353 10K下的粘度,并由密度数据计算出超额体积VE、由粘度数据计算出了不同温度和组成下的混合粘度的变化,同时对不同温度下的超额体积与组成的关系进行了多元回归,对混合粘度变化随组成的关系按Redlich-Kister方程进行了关联。     

含非对称Gemini离子液体二元混合体系的体积和黏度性质

在温度分别为293.15、303.15、313.15、323.15和333.15 K及大气压下,系统测定了非对称Gemini离子液体,1-(3-(三甲基铵)丙-1-基)-3-甲基咪唑双氰胺盐([N₁₁₁C₃MIM][N(CN)₂]₂),分别与乙腈(MeCN)、甲醇(MeOH)、乙醇(EtOH)所组成的二元混合物的密度和黏度。由密度和黏度值分别计算了二元混合物的超额摩尔体积()和超额黏度(Δη)。和Δη随组成的变化关系由Redlich-Kister方程进行了回归,得到方程参数。结果表明,和Δη值与理想溶液间为负偏差,且存在最小值,说明二元体系中[N₁₁₁C₃MIM][N(CN)₂]₂和溶剂分子间相互作用力更强,同时与所研究分子的大小和形状的差异有关。同时,和Δη随温度的变化关系表明,温度对研究混合物中的分子间相互作用有很大影响。     

巴豆酸乙酯与乙醇混合液密度和粘度的测定及关联

主要介绍了3-羟基丁酸乙酯合成过程中的相关物系的物性测定.在常压下采用U形振动管密度计测定了巴豆酸乙酯与乙醇的混合液在293.15～343.15 K下的密度,用乌氏粘度计测定了此混合溶液在293.15～343.15 K下的粘度,并由密度数据计算出超额体积V E、由粘度数据计算出了不同温度和组成下的混合粘度的变化Δη,V E和Δη这些值均为负值.同时对不同温度下的超额体积与组成的关系,粘度变化与组成的关系分别用Redlich-Kister方程进行了关联,最大标准偏差小于5%;说明此方程可适用于回归两相体系中上述的物性数据.     

碳酸二甲酯相关二元体系粘度和密度的测定及关联

在常压下采用U形振动管密度计测定了碳酸二甲酯-甲醇的混合液在293．15～323．15K和碳酸二甲酯-氯苯的混和液在293．15～343．15K下的密度;用乌氏粘度计测定了这两个混合溶液在相应温度下的粘度,并由密度数据计算出超额体积V^E、由粘度数据计算出了不同温度和组成下的混合粘度的变化Δη,前者V^E、Δη均为负值。后者V^E为正值,Δη基本聚集在0附近。对不同温度下的超额体积、混合粘度变化与组成的关系按Redlich-Kister方程进行了关联,最大标准偏差小于5％;说明这两体系适合采用此方程回归。