Effect of pyrolysis temperature on the mechanical evolution of SiCf/SiC composites fabricated by PIP

Three types of SiC_f/SiC composites with a four-step three-dimensional SiC fibre preform and pyrocarbon interface fabricated via precursor infiltration and pyrolysis at 1100 °C, 1300 °C, and 1500 °C were heat-treated at 1300 °C under argon atmosphere for 50 h. The effects of the pyrolysis temperature on the microstructural and mechanical properties of the SiC_f/SiC composites were studied. With an increase in the pyrolysis temperature, the SiC crystallite size of the as-fabricated composites increased from 3.4 to 6.4 nm, and the flexural strength decreased from 742 ± 45 to 467 ± 38 MPa. After heat treatment, all the samples exhibited lower mechanical properties, accompanied by grain growth, mass loss, and the formation of open pores. The degree of mechanical degradation decreased with an increase in the pyrolysis temperature. The composites fabricated at 1500 °C exhibited the highest property retention rates with 90% flexural strength and 98% flexural modulus retained. The mechanism of the mechanical evolution after heat treatment was revealed, which suggested that the thermal stability of the mechanical properties is enhanced by the high crystallinity of the SiC matrix after pyrolysis at higher temperatures.     

The mechanical,thermophysical and electromagnetic properties of UD SiCf/SiC composites in different directions

Unidirectional (UD) silicon carbide (SiC) fiber-reinforced SiC matrix (UD SiC_f/SiC) composites with CVI BN interphase were fabricated by polymer infiltration-pyrolysis (PIP) process. The effects of the anisotropic distribution of SiC fibers on the mechanical properties, thermophysical properties and electromagnetic properties of UD SiC_f/SiC composites in different directions were studied. In the direction parallel to the axial direction of SiC fibers, SiC fibers bear the load and BN interphase ensures the interface debonding, so the flexural strength and the fracture toughness of the UD SiC_f/SiC composites are 813.0 ± 32.4 MPa and 26.1 ± 2.9 MPa·m^1/2, respectively. In the direction perpendicular to the axial direction of SiC fibers, SiC fibers cannot bear the load and the low interfacial bonding strengths between SiC fiber/BN interphase (F/I) and BN interphase/SiC matrix (I/M) both decrease the matrix cracking stress, so the corresponding values are 36.6 ± 6.9 MPa and 0.9 ± 0.5 MPa?m^1/2, respectively. The thermal expansion behaviors of UD SiC_f/SiC composites are similar to those of SiC fibers in the direction parallel to the axial direction of SiC fibers, and are similiar to those of SiC matrix in the direction perpendicular to the axial direction of SiC fibers. The total electromagnetic shielding effectiveness (EM SE_T) of UD SiC_f/SiC composites attains 32 dB and 29 dB when the axial direction of SiC fibers is perpendicular and parallel to the electric field direction, respectively. The difference of conductivity in different directions is the main reason causing the different SE_T. And the dominant electromagnetic interference (EMI) shielding mechanism is absorption for both studied directions.     

The effects of preparation temperature on the SiCf/SiC 3D4d woven composite

Continuous silicon carbide fiber reinforced silicon carbide matrix (SiC_f/SiC) composites have promising applications in aero-engine due to their unique advantages, such as low density, high modulus and strength, outstanding high temperature resistance and oxidation resistance. As SiC fibers are main reinforcements in SiC_f/SiC composites, the crystallization rate and initial damage degree of SiC fibers are seriously influenced by preparation temperatures of SiC_f/SiC composites, namely mechanical properties of SiC fibers and SiC_f/SiC composites are influenced by preparation temperatures. In this paper, KD-II SiC fibers were woven into 3D4d preforms and SiC matrix was fabricated by PIP process at 1100 °C, 1200 °C, 1400 °C and 1600 °C. Digital image correlation (DIC) method was adopted to measure the uniaxial tensile properties of these SiC_f/SiC composites. In addition, finite element method (FEM) based on representative volume element (RVE) was adopted to predict the mechanical properties of SiC_f/SiC composites. The good agreements between numerical results and experimental results of uniaxial tensile tests verified the validity of the RVE. In last, the transverse tensile, transverse shear, uniaxial shear properties were predicted by this method. The predicted results illustrated that axial tensile, transverse tensile and axial shear properties were greatly influenced by the preparation temperatures of SiC_f/SiC composites while transverse shear properties were not significantly various. And the mechanical properties of SiC_f/SiC composites peaked at 1200 °C among these four temperatures while their values reached their lowest points at 1600 °C because of thermal damage and brittle failure of SiC_f/SiC composites.     

Influence of pyrolysis and melt infiltration temperatures on the mechanical properties of SiCf/SiC composites

In order to improve the degree of matrix densification of SiC_f/SiC composites based on liquid silicon infiltration (LSI) process, the microstructure and mechanical properties of composites according to various pyrolysis temperatures and melt infiltration temperatures were investigated.Comparing the microstructures of SiC_f/C carbon preform by a one-step pyrolysis process at 600 °C and two-step pyrolysis process at 600 and 1600 °C, the width of the crack and microcrack formation between the fibers and matrix in the fiber bundle increased during the two-step pyrolysis process. For each pyrolysis process, the density, porosity, and flexural strength of the SiC_f/SiC composites manufactured by the LSI process at 1450–1550 °C were measured to evaluate the degree of matrix densification and mechanical properties. As a result, the SiC_f/SiC composite that was fabricated by the two-step pyrolysis process and LSI process showed an 18% increase in density, 16%p decrease in porosity, and 150% increase in flexural strength on average compared to the composite fabricated by the one-step pyrolysis process.In addition, among the SiC_f/SiC specimens fabricated by the LSI process after the same two-step pyrolysis process, the specimen that underwent the LSI process at 1500 °C showed 30% higher flexural strength on average than those at 1450 or 1550 °C. Furthermore, under the same pyrolysis temperature, the mechanical strength of SiC_f/SiC specimens in which the LSI process was performed at 1500 °C was higher than that of the 1550 °C although both porosity and density were almost similar. This is because the mechanical properties of the Tyranno-S grade SiC fibers degraded rapidly with increasing LSI process temperature.     

Effect of SiC nanowires on the mechanical properties and thermal conductivity of 3D-SiCf/SiC composites prepared via precursor infiltration pyrolysis

In this study, SiC nanowires (SiC_NWS) were grown in situ on the surface of PyC interface through chemical vapor infiltration (CVI) to improve the mechanical characteristics and thermal conductivity of three-dimensional SiC_f/SiC composites fabricated via precursor infiltration pyrolysis (PIP). The effect of SiC_NWS on the properties of the obtained composites was investigated by comparing them with conventional SiC_f/PyC/SiC composites. After the deposition of SiC_NWS, the flexural strength of the SiC_f/SiC composites was found to increase by 46 %, and the thermal conductivity showed an obvious increase at 25?1000 °C. The energy release of the composites in the damage evolution process was analysed by acoustic emission. The results indicated that the damage evolution process was delayed owing to the decrease in porosity, the crack deflection and bridging of the SiC_NWS. Furthermore, the excellent thermal conductivity was attributed to the thermally conductive pathways formed by the SiC_NWS in the dense structure.     

Ring compression properties of SiCf/SiC composites prepared by chemical vapor infiltration

SiC fiber reinforced SiC matrix (SiC_f/SiC) composites prepared by chemical vapor infiltration are one of promising materials for nuclear fuel cladding tube due to pronounced low radioactivity and excellent corrosion resistance. As a structure component, mechanical properties of the composites tubes are extremely important. In this study, three kinds of SiC_f preform with 2D fiber wound structure, 2D plain weave structure and 2.5D shallow bend-joint structure were deposited with PyC interlayer of about 150–200?nm, and then densified with SiC matrix by chemical vapor infiltration at 1050?°C or 1100?°C. The influence of preform structure and deposition temperature of SiC matrix on microstructure and ring compression properties of SiC_f/SiC composites tubes were evaluated, and the results showed that these factors have a significant influence on ring compression strength. The compressive strength of SiC_f/SiC composites with 2D plain weave structure and 2.5D shallow bend-joint structure are 377.75?MPa and 482.96?MPa respectively, which are significantly higher than that of the composites with 2D fiber wound structure (92.84?MPa). SiC_f/SiC composites deposited at 1100?°C looks like a more porous structure with SiC whiskers appeared when compared with the composites deposited at 1050?°C. Correspondingly, the ring compression strength of the composites deposited at 1100?°C (566.44?MPa) is higher than that of the composites deposited at 1050?°C (482.96?MPa), with a better fracture behavior. Finally, the fracture mechanism of SiC_f/SiC composites with O-ring shape was discussed in detail.     

Mechanical properties of the SiCf/SiC composites reinforced with KD-I and KD-II fibers fabricated assisted by a microwave heating method

SiC_f/SiC composites using KD-I and KD-II SiC fibers braided preforms as the reinforcements were fabricated by applying the polymer impregnation and pyrolysis (PIP) technique with a microwave heating assistance. The microwave heating temperature was 1100 °C, 1200 °C, 1300 °C, and 1400 °C, respectively. Microstructures, flexure properties, and fracture behaviors of the composites were investigated. The KDIISiC_f/SiC composites exhibited higher flexure properties and improved non-brittle fracture characteristics than those of the KD-ISiC_f/SiC composites. The differences in the flexural properties, fracture behaviors and microstructures between the KD-I and KDIISiC_f/SiC composites were discussed based on the tensile properties of the SiC filaments and the interfacial bonding statues in the composites.     

Effect of SiC interphase on the mechanical,high-temperature dielectric and high-temperature microwave absorption properties of the SiCf/SiC/Mu composites

In this study, SiC interphase was prepared via a precursor infiltration-pyrolysis process, and effects of dipping concentrations on the mechanical, high-temperature dielectric and microwave absorption properties of the SiC_f/SiC/Mu composites had been investigated. Results indicated that different dipping concentrations influenced ultimate interfacial morphology. The SiC interphase prepared with 5 wt% PCS/xylene solution was smooth and homogeneous, and no bridging between the fiber monofilament could be observed. At the same time, SiC interphase prepared with 5 wt% PCS/xylene solution had significantly improved mechanical properties of the composite. In particular, the flexural strength of the composite prepared with 5 wt% PCS/xylene solution reached 281 MPa. Both ε′ and ε′′ of the SiC_f/SiC/Mu composites were enhanced after preparing SiC interphase at room temperature. The SiC_f/SiC/Mu composite prepared with 5 wt% PCS/xylene solution showed the maximum dielectric loss value of 0.38 at 10 GHz. Under the dual action of polarization mechanism and conductance loss, both ε′ and ε′′ of the SiC_f/SiC/Mu composites enhanced as the temperature increased. At 700 °C, the corresponding bandwidth (RL ≤ ?5 dB) of SiC_f/SiC/Mu composites prepared with 5 wt% PCS/xylene solution can reach 3.3 GHz at 2.6 mm. The SiC_f/SiC/Mu composite with SiC interphase prepared with 5 wt% PCS/xylene solution is expected to be an excellent structural-functional material.     

Property evolutions of Si/mixed Yb2Si2O7 and Yb2SiO5 environmental barrier coatings completely wrapping up SiCf/SiC composites under 1300 °C water vapor corrosion

A bi-layer environmental barrier coating (EBC) consisting of silicon(Si) bond coat/mixed ytterbium disilicate (Yb₂Si₂O₇) and ytterbium monosilicate (Yb₂SiO₅) topcoats has been successfully prepared to completely wrap up the SiC_f/SiC composites and the protective effects of such EBC have been evaluated by soaking them in a mixed 50% O₂ and 50% H₂O corrosive gases at 1300 °C for various times. In topcoats, Yb₂Si₂O₇ is the major phase, providing good thermal expansion coefficient (CTE) matching with composite substrate and thus excellent thermal shock resistance, whereas Yb₂SiO₅ is the dispersing minor phase, providing improved water vapor corrosion resistance. The completely wrapping up of SiC_f/SiC composites by above EBC system is employed to avoid direct exposure to the corrosive conditions, making it possible to evaluate the genuine protection effects of current EBCs. Under 1300 °C water vapor corrosion, the mass change, the phase composition and the evolution of microstructure are investigated, which suggest that the bi-layer EBC has excellent performance on protecting SiC_f/SiC composites from water vapor corrosion at 1300 °C.     

Tensile creep properties and damage mechanisms of 2D-SiCf/SiC composites reinforced with low-oxygen high-carbon type SiC fiber

Tensile creep properties of 2D-SiC_f/SiC composites reinforced with low-oxygen high-carbon type SiC fibers were studied in vacuum at 1300°C∼1430°C. The fracture morphology was observed by scanning electron microscopy and the damage of fiber in 2D-SiC_f/SiC composites was characterized by nanoindentation. Moreover, the microstructure of the composite was investigated by high-resolution transmission electron microscopy. The results show that rupture time is much shortened and steady-state creep rate increase three orders of magnitude when creep temperature is higher than 1400°C. There are two different creep damage mechanisms due to the decrease of interfacial bonding strength at high temperature. The amorphous SiO_xC_y phase in the fibers can crystallize into SiC and C and the SiC grain grows in the fiber. The microstructural changes lead to the decrease of fiber strength and degrade the creep properties of the composite above 1400°C.     

Excellent ablation resistance and reusability of silicon carbide fiber reinforced silicon carbide composite in dissociated air plasmas

This work explores the potentials of SiC fiber reinforced SiC matrix composites (SiC_f/SiC) with SiC coating to resist aerodynamic ablations for thermal protection purpose. A plasma wind tunnel is employed to evaluate their anti-ablation property in dissociated air plasmas. The results suggest a critical ablation temperature of SiC coated SiC_f/SiC, ≈ 1910 °C, which is the highest ever reported in literatures. Benefited by ‘all-SiC’ microstructures and relative flat ablated surfaces, the SiC_f/SiC is still ablation-resistant up to ≈ 1820 °C after the occurrence of ablation. This implies an excellent ablation resistance and reusability property of SiC_f/SiC, which surpasses that of traditional carbon fiber reinforced composites. Finally, an ablation mechanism dominated by surface characteristic is proposed. For the SiC coated SiC_f/SiC, ablation is prone to take place at surface cracks formed by thermal mismatch; while for the ablated SiC_f/SiC, ablation is triggered at the exposed fiber bundles which is over-heated in the plasmas.     

Mechanical properties and strengthening mechanism of SiCf/SiC mini-composites modified by SiC nanowires

The effects of the SiC nanowires (SiCNWs) and PyC interface layers on the mechanical and anti-oxidation properties of SiC fiber (SiC_f)/SiC composites were investigated. To achieve this, the PyC layer was coated on the SiC_f using a chemical vapour infiltration (CVI) method. Then, SiCNWs were successfully coated on the surface of SiC_f/PyC using the electrophoretic deposition method. Finally, a thin PyC layer was coated on the surface of SiC_f/PyC/SiCNWs. Three mini-composites, SiC_f/PyC/SiC, SiC_f/PyC/SiCNWs/SiC, and SiC_f/PyC/SiCNWs/PyC/SiC, were fabricated using the typical precursor infiltration and pyrolysis method. The morphologies of the samples were examined using scanning electron microscopy and energy dispersive X-ray spectrometry. Tensile and single-fibre push-out tests were carried out to investigate the mechanical performance and interfacial shear strength of the composites before and after oxidization at 1200 °C. The results revealed that the SiC_f/PyC/SiCNWs/SiC composites showed the best mechanical and anti-oxidation performance among all the composites investigated. The strengthening and toughening is mainly achieved by SiCNWs optimization of the interfacial bonding strength of the composite and its own nano-toughening. On the basis of the results, the effects of SiCNWs on the oxidation process and retardation mechanism of the SiC_f/SiC mini-composites were investigated.     

Fine study of hierarchical interphase constructed by boron nitride and carbon nanotubes in SiCf/SiC composites

A fine study of the interfacial part in the silicon carbide fiber (SiC_f) reinforced silicon carbide (SiC) composites was conducted by transmission electron microscopy. The boron nitride (BN) and carbon nanotubes (CNTs) were progressively coated on the SiC_f by chemical vapor deposition method to form a hierarchical structure. Three composites with different interfaces, SiC_f–CNTs/SiC, SiC_f@BN/SiC, and SiC_f@BN–CNTs/SiC, were fabricated by polymer infiltration and pyrolysis method. The interfaces and microstructures of the three composites were carefully characterized to investigate the improvement mechanism of strength and toughness. The results showed that BN could protect the surface of SiC_f from corrosion and oxidation so that improved the possibility of debonding and pullout. CNTs could avoid the propagation of cracks in the composites so that improved the damage resistance of the matrix. The synergistic reinforcement brought by BN and CNTs interfaces made the SiC_f@BN–CNTs/SiC composites with a tensile fracture strength as high as 359 MPa, with an improvement of 23% compared to that of SiC_f@BN/SiC.     

Deformation and damage processes during tensile creep of ceramic-fibre-reinforced ceramic–matrix composites

The tensile creep and creep fracture properties in air at 1300°C are compared for SiC_f/SiC and SiC_f/Al₂O₃ composites, each reinforced with 0.38 volume fractions of interwoven silicon carbide (Nicalon™) fibre bundles aligned parallel and normal to the stress direction. The differing behaviour patterns displayed by these 0/90° woven composites are analysed to identify the processes controlling creep strain accumulation and crack development.     

Microstructure and properties of SiCf/SiC composite joints with CaO–Y2O3–Al2O3–SiO2 interlayer

Using CaO, Y₂O₃, Al₂O₃, and SiO₂ micron-powders as raw materials, CaO–Y₂O₃–Al₂O₃–SiO₂ (CYAS) glass was prepared using water cooling method. The coefficient of thermal expansion (CTE) of CYAS glass was found to be 4.3 × 10^?6/K, which was similar to that of SiC_f/SiC composites. The glass transition temperature of CYAS glass was determined to be 723.1 °C. With the increase of temperature, CYAS glass powder exhibited crystallization and sintering behaviors. Below 1300 °C, yttrium disilicate, mullite and cristobalite crystals gradually precipitated out. However, above 1300 °C, the crystals started diminishing, eventually disappearing after heat treatment at 1400 °C. CYAS glass powder was used to join SiC_f/SiC composites. The results showed that the joint gradually densified as brazing temperature increased, while the phase in the interlayer was consistent with that of glass powder heated at the same temperature. The holding time had little effect on phase composition of the joint, while longer holding time was more beneficial to the elimination of residual bubbles in the interlayer and promoted the infiltration of glass solder into SiC_f/SiC composites. The joint brazed at 1400 °C/30 min was dense and defect-free with the highest shear strength of about 57.1 MPa.     

Preparation of SiCf/Si–O–C composites by impregnation pyrolysis of polysiloxane and its electromagnetic wave absorption properties

High-temperature structural electromagnetic wave (EMW) absorption materials are increasing in demand because they can simultaneously possess the functions of mechanical load-bearing, heatproof, and EMW absorption. Herein, SiC_f/Si–O–C composites were prepared by precursor impregnation pyrolysis using continuous SiC fibers needled felt as reinforcement and polysiloxane as a precursor, respectively. The phase composition, microstructure, complex permittivity, and EMW absorption properties of SiC_f/Si–O–C composites after annealing at various temperatures were investigated. The annealing at 1400–1500°C affects positively the EMW absorption performance of the composites, because the β-SiC microcrystals and SiC nanowires were generated by the activation of carbothermal reduction reaction in the composites, and the aspect ratio of SiC nanowires increased with the rise of temperature. The composites exhibit optimal EMW absorption performance, with the effective absorption bandwidth covering the entire X-band and the minimum reflection loss (RL_min) of −32.8 dB at 4.0 mm when the annealing temperature is raised to 1500°C. This is because that the impedance matching is improved as the rising of ε′ and decreasing of ε″ due to the conversion of free carbon in the composite into SiC nanowires.     

Ti3SiC2 interphase coating in SiCf/SiC composites: Effect of the coating fabrication atmosphere and temperature

The SiC fibers were coated with Ti₃SiC₂ interphase by dip-coating. The Ti₃SiC₂ coated fibers were heat-treated from 900 °C to 1100 °C in vacuum and argon atmospheres to comparatively analyze the effect of temperature and atmosphere on the microstructural evolution and mechanical strength of the fibers. The results show that the surface morphology of Ti₃SiC₂ coating is rough in vacuum and Ti₃SiC₂ is decomposed at 1100 °C. However, in argon atmosphere, the surface morphology is smooth and Ti₃SiC₂ is oxidized at 1000 °C and 1100 °C. At 1100 °C, Ti₃SiC₂ oxidized to form a thin layer of amorphous SiO₂ embedded with TiO₂ grains. Meanwhile, defects and pores appeared in the interphase scale. As a result, the fiber strength treated in the argon was lower than that treated in vacuum. The porous Ti₃SiC₂ interphase fabricated under vacuum was then employed to prepare the SiC_f/SiC mini composite by chemical vapor infiltration (CVI) combined with precursor infiltration pyrolysis (PIP), and can effectively improve the toughness of SiC_f/SiC mini composite. The propagating cracks can be deflected within the porous interphase layer, which promotes fiber pull-outs under the tensile strength.     

SiC fiber reinforced geopolymer composites,part 2: Continuous SiC fiber

In this paper, unidirectional SiC fiber (SiC_f) reinforced geopolymer composites (SiC_f/geopolymer) were prepared and effects of fiber contents on the microstructure and mechanical properties of the composites in different directions were investigated. The XRD results showed that addition of SiC_f retarded geopolymerization process of geopolymer matrix by weakening the typical amorphous hump. SiC_f in all the composites were well infiltrated by geopolymer matrix, but microcracks which were perpendicular to the fiber axial direction were noted in the interface area due to the thermal shrinkage of matrix during the curing process. With the increases in fiber contents, although Young's modulus of the composites increased continuously, flexural strength, fracture toughness and work of fracture increased at first, reached their peak values and then decreased. And when fiber content was 20 vol%, the composites showed the highest flexural strength, fracture toughness and work of fracture, which were 14.2, 15.2 and 81.6 times as high as those of pristine geopolymer, respectively, indicating significant strengthening and toughening effects from SiC_f. Meanwhile, SiC_f/geopolymer composites failed in different failure modes in the different directions, i.e., tensile failure mode in the x direction (in-plane and perpendicular to the fiber axial direction) and shear failure mode in the z direction (laminate lay-up direction).     

Theoretical prediction and experimental verification on EMI shielding effectiveness of dielectric composites using complex permittivity

The evaluation and optimization of EMW absorbing properties have been widely studied, but little research focused on EMI shielding properties predicted by complex permittivity. Based on the transmission-line theory, shielding effectiveness (SE) of a dielectric composite was evaluated by the reflection coefficient (Г) and transmission coefficient (T) which were calculated by the complex permittivity. SiC_f/SiCN composites containing different content of CVI SiCN matrix are attractive for their tunable dielectric properties, which may vary from EMW absorption to EMI shielding. Therefore, SiC_f/SiCN composites are typical dielectric composites used for experimental verification, and the results indicate that the dielectric composites without CVI SiCN phase have good EMW absorbing properties, while they exhibit good EMI shielding effectiveness with CVI SiCN phase. This work builds a relationship between the EMI shielding effectiveness and the complex permittivity, and obtains the optimized complex permittivity for excellent EMI shielding effectiveness.     

Effect of oxidation treatment on KD–II SiC fiber–reinforced SiC composites

Continuous silicon carbide fiber–reinforced silicon carbide matrix (SiC_f/SiC) composites have developed into a promising candidate for structural materials for high–temperature applications in aerospace engine systems. This is due to their advantageous properties, such as low density, high hardness and strength, and excellent high temperature and oxidation resistance. In this study, SiC_f/SiC composites were fabricated via polymer infiltration and pyrolysis (PIP) with the lower–oxygen–content KD–II SiC fiber as the reinforcement; a mixture of 2,4,6,8–tetravinyl–2,4,6,8–tetramethylcyclotetrasiloxane (V4) and liquid polycarbosilane (LPCS), known as LPVCS, was used as the precursor; while pyrolytic carbon (PyC) was used as the interface. The effects of oxidation treatment at different temperatures on morphology, structure, composition, and mechanical properties of the KD–II SiC fibers, SiC matrix from LPVCS precursor conversion, and SiC_f/SiC composites were comprehensively investigated. The results revealed that the oxidation treatment greatly impacted the mechanical properties of the SiC fiber, thereby significantly influencing the mechanical properties of the SiC_f/SiC composite. After oxidation at 1300 °C for 1 h, the strength retention rates of the fiber and composite were 41% and 49%, respectively. In terms of the phase structure, oxidation treatment had little effect on the SiC fiber, while greatly influencing the SiC matrix. A weak peak corresponding to silica (SiO₂) appeared after high–temperature treatment of the fiber; however, oxidation treatment of the matrix led to the appearance of a very strong diffraction peak that corresponds to SiO₂. The analysis of the morphology and composition indicated cracking of the fiber surface after oxidation treatment, which was increasingly obvious with the increase in the oxidation treatment temperature. The elemental composition of the fiber surface changed significantly, with drastically decreased carbon element content and sharply increased oxygen element content.