Simulation on microstructure evolution and mechanical properties of Mg−Y alloys: Effect of trace Y

The influence of trace Y on the microstructure evolution and mechanical properties of Mg_100?xY_x (x=0.25, 0.75, 1.5, 3, 4, 5, at.%) alloys during solidification process was investigated via molecular dynamics (MD) simulations. The results show that the Mg_100?xY_x alloys are mainly characterized by a face-centered cubic (FCC) crystal structure; this is different from pure metal Mg, which exhibits a hexagonal close packed (HCP) structure at room temperature. Among these alloys, Mg_99.25Y_0.75 has a larger proportion of FCC cluster structures, with the highest fraction reaching 56.65%. As the content of the Y increases up to 5 at.% (Mg₉₅Y₅ alloy), the amount of amorphous structures increases. The mechanical properties of the Mg_100?xY_x alloys are closely related to their microstructures. The Mg_99.25Y_0.75 and Mg₉₇Y₃ alloys exhibit the highest yield strengths of 1.86 and 1.90 GPa, respectively. The deformation mechanism of the Mg?Y alloys is described at the atomic level, and it is found that a difference in the FCC proportion caused by different Y contents leads to distinct deformation mechanisms.     

Effect of Al addition on microstructure and mechanical properties of Mg−Gd−Zn alloys

The microstructure evolution and mechanical properties of Mg?15.3Gd?1Zn alloys with different Al contents (0, 0.4, 0.7 and 1.0 wt.%) were investigated. Microstructural analysis indicates that the addition of 0.4 wt.% Al facilitates the formation of 18R-LPSO phase (Mg₁₂Gd(Al, Zn)) in the Mg?Gd?Zn alloy. The contents of Al₁₁Gd₃ and Al₂Gd increase with the increase of Al content, while the content of (Mg, Zn)₃Gd decreases. After homogenization treatment, (Mg, Zn)₃Gd, 18R-LPSO and some Al₁₁Gd₃ phases are transformed into the high-temperature stable 14H-LPSO phases. The particulate Al?Gd phases can stimulate the nucleation of dynamic recrystallization by the particle simulated nucleation (PSN) mechanism. The tensile strength of the as-rolled alloys is improved remarkably due to the grain refinement and the fiber-like reinforcement of LPSO phase. The precipitation of the β′ phase in the peak-aged alloys can significantly improve the strength. The peak-aged alloy containing 0.4 wt.% Al achieves excellent mechanical properties and the UTS, YS and elongation are 458 MPa, 375 MPa and 6.2%, respectively.     

Effects of Li content on microstructure and mechanical properties of as-cast Mg−xLi−3Al−2Zn−0.5Y alloys

The effects of Li content on the microstructure and mechanical properties of the as-cast Mg?xLi?3Al?2Zn? 0.5Y (LAZx32-0.5Y) alloys were investigated by XRD, SEM, TEM, hardness tester and universal testing machine. The results show that the matrix of the alloy transforms from α-Mg to α-Mg+β-Li and then to β-Li when the Li content increases from 4% to 14% (mass fraction). All LAZx32-0.5Y alloys contain AlLi and Al₂Y, while MgLi₂Al appears only in the alloy containing the β-Li matrix. As the Li content increases, the content of AlLi and MgLi₂Al gradually increases, while the content of Al₂Y does not change much. As the Li content increases from 4% to 10%, the ultimate tensile strength and hardness of the as-cast LAZx32-0.5Y alloys gradually decrease while the elongation gradually increases. The corresponding fracture mechanism changes from cleavage fracture to quasi-cleavage fracture and then to microporous aggregation fracture. This is mainly attributed to the decrease of α-Mg and the increase of β-Li in the alloy. When the Li content continues to increase to 10% and 14%, the yield strength, ultimate tensile strength and hardness of the as-cast LAZx32-0.5Y alloys gradually increase, while the elongation decreases sharply, which is mainly attributed to the nano-scale MgLi₂Al uniformly distributed in the β-Li matrix.     

Effects of minor Sc and Zr additions on mechanical properties and microstructure evolution of Al−Zn−Mg−Cu alloys

The effects of minor Sc and Zr additions on the mechanical properties and microstructure evolution of Al−Zn−Mg−Cu alloys were studied using tensile tests, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The ultimate tensile strength of the peak-aged Al−Zn−Mg−Cu alloy is improved by about 105 MPa with the addition of 0.10% Zr. An increase of about 133 MPa is observed with the joint addition of 0.07% Sc and 0.07% Zr. For the alloys modified with the minor addition of Sc and Zr (0.14%), the main strengthening mechanisms of minor addition of Sc and Zr are fine-grain strengthening, sub-structure strengthening and the Orowan strengthening mechanism produced by the Al₃(Sc,Zr) and Al₃Zr dispersoids. The volume of Al₃Zr particles is less than that of Al₃(Sc,Zr) particles, but the distribution of Al₃(Sc,Zr) particles is more dispersed throughout the matrix leading to pinning the dislocations motion and restraining the recrystallization more effectively.     

Effect of Al addition on microstructure and mechanical properties of Mg−Zn−Sn−Mn alloy

The microstructure and properties of the as-cast, as-homogenized and as-extruded Mg−6Zn−4Sn−1Mn (ZTM641) alloy with various Al contents (0, 0.5, 1, 2, 3 and 4 wt.%) were investigated by OM, XRD, DSC, SEM, TEM and uniaxial tensile tests. The results show that when the Al content is not higher than 0.5%, the alloys are mainly composed of α-Mg, Mg₂Sn, Al₈Mn₅ and Mg₇Zn₃ phases_. When the Al content is higher than 0.5%, the alloys mainly consist of α-Mg, Mg₂Sn, MgZn, Mg₃₂(Al,Zn)₄₉, Al₂Mg₅Zn₂, Al₁₁Mn₄ and Al₈Mn₅ phases. A small amount of Al (≤1%) can increase the proportion of fine dynamic recrystallized (DRXed) grains during hot-extrusion process. The room- temperature tensile test results show that the ZTM641−1Al alloy has the best comprehensive mechanical properties, in which the ultimate tensile strength is 332 MPa, yield strength is 221 MPa and the elongation is 15%. Elevated- temperature tensile test results at 150 and 200 °C show that ZTM641−2Al alloy has the best comprehensive mechanical properties.     

Effect of Sn content on microstructure and tensile properties of as-cast and as-extruded Mg−8Li−3Al−(1,2,3)Sn alloys

The effects of Sn content on microstructure and tensile properties of as-cast and as-extruded Mg−8Li−3Al− (1,2,3)Sn (wt.%) alloys were investigated by X-ray diffractometry (XRD), optical microscopy (OM), scanning electron microscopy (SEM) and tensile test. It is found that, as-cast Mg−8Li−3Al−(1,2,3)Sn alloys consist of α-Mg+β-Li duplex matrix, MgLiAl₂ and Li₂MgSn phases. Increasing Sn content leads to grain refinement of α-Mg dendrites and increase in content of Li₂MgSn phase. During hot extrusion, complete dynamic recrystallization (DRX) takes place in β-Li phase while incomplete DRX takes place in α-Mg phase. As Sn content is increased, the volume fraction of DRXed α-Mg grains is increased and the average grain size of DRXed α-Mg grains is decreased. Increasing Sn content is beneficial to strength but harmful to ductility for as-cast Mg−8Li−3Al−(1,2,3)Sn alloys. Tensile properties of Mg−8Li−3Al− (1,2,3)Sn alloys are improved significantly via hot extrusion and Mg−8Li−3Al−2Sn alloy exhibits the best tensile properties.     

Effect of Gd content on microstructure and dynamic mechanical properties of solution-treated Mg−xGd−3Y−0.5Zr alloy

The effect of Gd content ranging from 6.5 wt.% to 8.5 wt.% on microstructure evolution and dynamic mechanical behavior of Mg?xGd?3Y?0.5Zr alloys was investigated by optical microscopy, X-ray diffraction, scanning electron microscopy and split Hopkinson pressure bar. The microstructure of as-cast Mg?xGd?3Y?0.5Zr alloys indicates that the addition of Gd can promote grain refinement in the casting. Due to the rapid cooling rate during solidification, a large amount of non-equilibrium eutectic phase Mg₂₄(Gd,Y)₅ appears at the grain boundary of as-cast Mg?xGd?3Y?0.5Zr alloys. After solution treatment at 520 °C for 6 h, the Mg₂₄(Gd,Y)₅ phase dissolves into the matrix, and the rare earth hydrides (REH) phase appears. The stress?strain curves validate that the solution-treated Mg?xGd?3Y?0.5Zr alloys with optimal Gd contents maintain excellent dynamic properties at different strain rates. It was concluded that the variation of Gd content and the agglomeration of residual REH particles and dynamically precipitated fine particles are key factors affecting dynamic mechanical properties of Mg?xGd?3Y?0.5Zr alloys.     

Effects of Mg content on microstructure and mechanical properties of low Zn-containing Al−xMg−3Zn−1Cu cast alloys

Effects of Mg content on the microstructure and mechanical properties of low Zn-containing Al?xMg? 3Zn?1Cu cast alloys (x=3?5, wt.%) were investigated. As Mg content increased in the as-cast alloys, the grains were refined due to enhanced growth restriction, and the formation of η-Mg(AlZnCu)₂ and S-Al₂CuMg phases was inhibited while the formation of T-Mg₃₂(AlZnCu)₄₉ phase was promoted when Mg content exceeded 4 wt.%. The increase of Mg content encumbered the solution kinetics by increasing the size of eutectic phase but accelerated and enhanced the age-hardening through expediting precipitation kinetics and elevating the number density of the precipitates. As Mg content increased, the yield strength and tensile strength of the as-cast, solution-treated and peak-aged alloys were severally improved, while the elongation of the alloys decreased. The tensile strength and elongation of the peak-aged Al?5Mg?3Zn?1Cu alloy exceed 500 MPa and 5%, respectively. Precipitation strengthening implemented by T′ precipitates is the predominant strengthening mechanism in the peak-aged alloys and is enhanced by increasing Mg content.     

Effect of Gd on microstructure,mechanical properties,and corrosion behavior of as-homogenized Mg−8Li−3Al−2Zn−0.2Zr alloy

The microstructure observation, tensile test, electrochemical measurement, and corrosion morphology characterization were conducted to study the effect of Gd on the microstructure, mechanical properties, and corrosion behavior of as-homogenized Mg?8Li?3Al?2Zn?0.2Zr (LAZ832?0.2Zr) alloy. The addition of trace Gd can improve the mechanical properties of as-homogenized LAZ832?0.2Zr alloy by refining the microstructure, reducing the content of AlLi softening phase, and forming Al₂Gd strengthening phase. Meanwhile, the addition of trace Gd can weaken the microgalvanic corrosion between matrix phase and AlLi phase, inhibit the galvanic corrosion between α-Mg phase and β-Li phase, and result in the formation of dense oxide film containing Gd₂O₃, thereby improving the corrosion resistance of the alloy. When the Gd content is 1.0 wt.%, the alloy shows the best comprehensive properties with the ultimate tensile strength of 189.8 MPa, elongation of 42.3%, and corrosion rate (determined by hydrogen evolution) of 0.86 mm·a^?1.     

The effects of Sc on the microstructure and mechanical properties of hypo-eutectic Al−Si alloys

The eutectic Si microstructure in Al-8.5wt.%Si alloy was changed from large flakes to fine lamellar when the Sc amount in the alloy reached 0.2 wt.%. 0.8wt.%Sc was optimal in terms of attaining the best modification effect. Study on the distribution of the modifiers and measurement of the surface tension of Al-8.5wt.%Si alloy melt with added Sr, Na, and Sc modifiers, respectively, reveals that Sc modifies eutectic Si by a decrease of surface tension, while Sr and Na modify eutectic Si mainly by an impurity-induced twinning mechanism. Al-8.5wt.%Si-0.4wt.%Sc alloy displayed approximately 50 and 70% increases in tensile strength and elongation, respectively, over Al-8.5wt.%Si alloy in the cast state. It also presented approximately 65 and 70% increases in tensile strength and elongation, respectively, over Al-8.5wt.%Si alloy at a ppt heat-treated state at 200°C for 3 h.     

Effect of Y addition on microstructure and mechanical properties of Mg–Zn–Mn alloy

The effects of Y on the microstructure and mechanical properties of Mg–6Zn–1Mn alloy were investigated. The results show that the addition of Y has significant effect on the phase composition, microstructure and mechanical properties of Mg–6Zn–1Mn alloy. Varied phases compositions, including Mg₇Zn₃, I-phase (Mg₃YZn₆), W-phase (Mg₃Y₂Zn₃) and X-phase (Mg₁₂YZn), are obtained by adjusting the Zn to Y mass ratio. Mn element exists as the fine Mn particles, which are well distributed in the alloy. Thermal analysis and microstructure observation reveal that the phase stability follows the trend of X>W>I>Mg₇Zn₃. In addition, Y can improve the mechanical properties of Mg–Zn–Mn alloy significantly, and the alloy with Y content of 6.09% has the best mechanical properties. The high strength is mainly due to the strengthening by the grain size refinement, dispersion strengthening by fine Mn particles, and introduction of the Mg–Zn–Y ternary phases.     

Effect of welding speed on microstructure and mechanical properties of Al−Mg−Mn−Zr−Tialloy sheet during friction stir welding

Effects of welding speed on the microstructure evolution in the stir zone (SZ) and mechanical properties of the friction stir welding (FSW) joints were studied by OM, XRD, SEM, TEM, EBSD and tensile testing. Compared with the base metal (BM), an obviously fine dynamic recrystallization (DRX) microstructure occurs in the SZ and the DRX grain size decreases from 5.6 to 4.4 μm with the increasing of welding speed. Fine DRX microstructure is mainly achieved by continuous dynamic recrystallization (CDRX) mechanism, strain induced boundary migration (SIBM) mechanism and particle stimulated nucleation (PSN) mechanism. Meanwhile, the geometric coalescence and the Burke−Turnbull mechanism are the main DRX grain growth mechanisms. Among all the welding speeds, the joint welded at rotation speed of 1500 r/min and welding speed of 75 mm/min has the greatest tensile properties, i.e. ultimate tensile strength (UTS) of (509±2) MPa, yield strength (YS) of (282±4) MPa, elongation (El) of (23±1)%, and the joint efficiency of 73%.     

Effect of thermal exposure on microstructure and mechanical properties of Al−Si−Cu−Ni−Mg alloy produced by different casting technologies

The effect of thermal exposure at 350 °C for 200 h on microstructure and mechanical properties was investigated for Al−Si−Cu−Ni−Mg alloy, which was produced by permanent mold casting (PMC) and high pressure die casting (HPDC). The SEM and IPP software were used to characterize the morphology of Si phase in the studied alloys. The results show that the thermal exposure provokes spheroidization and coarsening of eutectic Si particles. The ultimate tensile strength of the HPDC alloy after thermal exposure is higher than that of the PMC alloy at room temperature. However, the TEPMC and TEHPDC alloys have similar tensile strength around 67 MPa at 350 °C. Due to the coarsening of eutectic Si, the TEPMC alloy exhibits better creep resistance than the TEHPDC alloy under studied creep conditions. Therefore, the alloys with small size of eutectic Si are not suitably used at 350 °C.     

Effect of cerium on microstructure and mechanical properties of Sn-Ag-Cu system lead-free solder alloys

The melting point, spreading property, mechanical properties and microstructures of Sn-3.0Ag-2.8Cu solder alloys added with micro-variable-Ce were studied by means of optical microscopy, scanning electron microscopy（SEM） and energy dispersive X-ray（EDX）. The results indicate that the melting point of Sn-3.0Ag-2.8Cu solder is enhanced by Ce addition; a small amount of Ce will remarkably prolong the creep-rupture life of Sn-3.0Ag-2.8Cu solder joint at room temperature, especially when the content of Ce is 0.1%, the creep-rupture life will be 9 times or more than that of the solder joint without Ce addition; the elongation of Sn-3.0Ag-2.SCu solder is also obviously improved even up to 15.7%. In sum, the optimum content of Ce is within 0.05%-0.1%.     

Effects of trace Ag on precipitation behavior and mechanical properties of extruded Mg−Gd−Y−Zr alloys

The effects of trace Ag element on the precipitation behaviors and mechanical properties of the Mg−7.5Gd− 1.5Y−0.4Zr (wt.%) alloy by means of tensile test, X-ray diffractometry, scanning electron microscopy, electron backscattered diffractometry, and scanning transmission electron microscopy. There is an unusual texture (〈0001〉//extrusion direction) in the extruded Mg−Gd−Y−Zr alloys containing 0.5 wt.% Ag. During the aging periods at 225 °C, the addition of the trace Ag does not form new precipitates, just accelerates aging kinetics, and refines β′ precipitates, thereby increasing the number density of the β′ precipitates by Ag-clusters. Moreover, the Mg−Gd−Y−Zr alloy containing 0.5 wt.% Ag shows the most excellent synergy of strength and plasticity (408 MPa of ultimate tensile strength, 265 MPa of yield strength, and 12.9% of elongation to failure) after peak-aging.     

Effect of Y content on microstructure and mechanical properties of 2519 aluminum alloy

The effects of yttrium（Y） content on precipitation hardening, elevated temperature mechanical properties and morphologies of 2519 aluminum alloy were investigated by means of microhardness test, tensile test, optical microscopy（OM）, transmission electron microscopy（TEM） and scanning electron microscopy（SEM）. The results show that the tensile strength increases from 485 MPa to 490 MPa by increasing Y content from 0 to 0.10%（mass fraction） at room temperature, and from 155 MPa to 205 MPa by increasing Y content from 0 to 0.20% at 300 ~C. The high strength of 2519 aluminum alloy is attributed to the high density of fine 0＇ precipitates and intermetallic compound AICuY with high thermal stability. Addition of Y above 0.20% in 2519 aluminum alloy may induce the decrease in the tensile strength both at room temperature （20 ℃） and 300℃.     

Effect of Al on microstructure and magnetic properties of mould-cast Nd60Fe40−xAlx alloys

Mould-cast Nd₆₀Fe_40−xAl_x (x=0, 5, 10) alloys were studied to clarify the effect of Al on the structural and magnetic properties. For binary Nd₆₀Fe₄₀, the metastable hard magnetic A₁ phase forms along with the Nd₂Fe₁₇ equilibrium phase. Partial substitution of Fe by Al favours the formation of the hard magnetic metastable A₁ phase manifested by a large magnetization.     

Microstructure and mechanical properties of friction stir processed Al−Mg2Si alloys

The microstructure and mechanical properties of friction stir processed Al−Mg₂Si alloys were studied by TEM and EBSD. The results showed that an increase in the tool rotation speed (300−700 r/min) led to a decrease in the defect area (from 10.5 mm² to zero), whereas the defect area demonstrated the opposite trend (increased to 1.5 mm² from zero) upon further increasing the rotation speed (700−1200 r/min). The types of defects were transformed from tunnel defects to fusion defects as the rotational speed increased. The coarse Mg₂Si dendrites were broken and fine particles (smaller than 10 μm) formed in the weld nugget (WN). The amount of low-angle grain boundaries increased significantly from 57.7% to 83.6%, which was caused by an increase in the content of the deformed structure (from 1.7% to 13.6%). The hardness, ultimate tensile strength (UTS) and elongation were all greatly improved for the weld nugget. The hardness values of the WNs had the following order: R300<R1200<R500<R900<R700. The UTS and elongation had the following order: BM (base material)<R300<R1200<R500<R900<R700. The UTS and the elongation for the WN were increased by one and three times, respectively.     

Effect of interlayer on microstructure and mechanical properties of Al–Ti ultrasonic welds

Joints of Al6061 and Ti6Al4?V alloys with pure Al-particle interlayers were conducted using ultrasonic spot welding. The microstructure, hardness, lap shear strength and fracture energy were measured for different welding energies. With increasing welding energy delivered through the sonotrode, the lap shear strength of the joints increased, reaching about 106?MPa at a welding energy of 1100?J, at which failure occurred in the pull-out mode. In the weld region, the hardness of Al6061 alloy increased with increasing weld energy, whereas the hardness of Ti6Al4?V did not change discernibly. No brittle intermetallic compounds were observed in the joints. Moreover, two simple mechanisms were described for the formation of ultrasonic spot-welded Al–Ti joints with and without the pure Al interlayer.     

Effect of Ru additions on microstructure and mechanical properties of Cr–TaCr2 alloys

Early work indicated that Ru reduced the ductile-to-brittle transition temperature of Cr even at small concentrations. To evaluate the potential of Ru as a beneficial alloying element in the two-phase Cr–TaCr₂ alloys, a number of Cr–8 at.%Ta alloys with 0–10 at.%Ru were prepared, and their microstructures and mechanical properties were evaluated. The Ru addition was found to move the eutectic point of Cr–TaCr₂ to a higher Ta level, as compared to the binary Cr–Ta system. Ru partitioned preferentially in the Laves phase over in the Cr matrix, with a partitioning ratio of 2–5:1, depending on the Ru addition level. Ru was also found to mainly occupy the Cr site in the TaCr₂ Laves phase. The hardness of both the primary Cr matrix and the eutectic microconstituent increased slightly with the increase in Ru addition. At a higher Ru addition level (i.e. 10 at.%), the hardness of the primary Cr matrix increased significantly, probably due to the precipitation of extremely fine Laves-phase precipitates. The Ru addition did not noticeably affect the fracture toughness of the two-phase alloys.