Improved photovoltaic energy output for cloudy conditions with a solar tracking system

This work describes measurements of the solar irradiance made during cloudy periods in order to improve the amount of solar energy captured during such periods. It is well-known that 2-axis tracking, in which solar modules are pointed at the sun, improves the overall capture of solar energy by a given area of modules by 30-50% versus modules with a fixed tilt. On sunny days the direct sunshine accounts for up to 90% of the total solar energy, with the other 10% from diffuse (scattered) solar energy. However, during overcast conditions nearly all of the solar irradiance is diffuse radiation that is isotropically-distributed over the whole sky. An analysis of our data shows that during overcast conditions, tilting a solar module or sensor away from the zenith reduces the irradiance relative to a horizontal configuration, in which the sensor or module is pointed toward the zenith (horizontal module tilt), and thus receives the highest amount of this isotropically-distributed sky radiation. This observation led to an improved tracking algorithm in which a solar array would track the sun during cloud-free periods using 2-axis tracking, when the solar disk is visible, but go to a horizontal configuration when the sky becomes overcast. During cloudy periods we show that a horizontal module orientation increases the solar energy capture by nearly 50% compared to 2-axis solar tracking during the same period. Improving the harvesting of solar energy on cloudy days is important to using solar energy on a daily basis for fueling fuel-cell electric vehicles or charging extended-range electric vehicles because it improves the energy capture on the days with the lowest hydrogen generation, which in turn reduces the system size and cost.     

Short-term predictability of photovoltaic production over Italy

Photovoltaic (PV) power production increased drastically in Europe throughout the last years. Since about the 6% of electricity in Italy comes from PV, an accurate and reliable forecasting of production would be needed for an efficient management of the power grid. We investigate the possibility to forecast daily PV electricity production up to ten days without using on-site measurements of meteorological variables. Our study uses a PV production dataset of 65 Italian sites and it is divided in two parts: first, an assessment of the predictability of meteorological variables using weather forecasts; second, an analysis of predicting solar power production through data-driven modelling. We calibrate Support Vector Machine (SVM) models using available observations and then we apply the same models on the weather forecasts variables to predict daily PV power production. As expected, cloud cover variability strongly affects solar power production, we observe that while during summer the forecast error is under the 10% (slightly lower in south Italy), during winter it is abundantly above the 20%.     

Searching for public benefits in solar subsidies: A case study on the Australian government’s residential photovoltaic rebate program

The Australian Government ran a renewable energy program in the 2000s that provided rebates to householders who acquired solar Photovoltaic (PV) energy systems. Originally called the Photovoltaic Rebate Program (PVRP), it was rebranded the Solar Homes and Communities Plan (SHCP) in November 2007. This paper evaluates both the PVRP and SHCP using measures of cost-effectiveness and fairness. It finds that the program was a major driver of a more than six-fold increase in PV generation capacity in the 2000s, albeit off a low base. In 2010, solar PV’s share of the Australian electricity market was still only 0.1%. The program was also environmentally ineffective and costly, reducing emissions by 0.09 MtCO₂-e/yr over the life of the rebated PV systems at an average cost of between AU$238 and AU$282/tCO₂-e. In addition, the data suggest there were equity issues associated with the program, with 66% of all successful applicants residing in postal areas that were rated as medium–high or high on a Socio-economic Status (SES) scale.     

Uniqueness verification of solar spectrum index of average photon energy for evaluating outdoor performance of photovoltaic modules

To analyze the effect of a spectral irradiance distribution of solar spectra on the outdoor performance of photovoltaic (PV) modules, an index for the spectral distribution is needed. Average photon energy (APE) which represents the average energy per photons included in a spectrum is one of these. In this study, the uniqueness of APE to the spectral irradiance distribution was statistically analyzed to assure that an APE value uniquely yields the shape of a solar spectrum. The similar methodology adopted in International Electrotechnical Commission to rate the spectral matching of a solar simulator was used for the analysis. The results showed that an APE value yielded a spectral irradiance distribution with quite small standard deviation. The analysis using APE showed that the outdoor performance of crystalline Si PV modules depended almost only on a module temperature, while that of amorphous Si ones mainly depended on APE. The behaviors were reasonable considering from the operation mechanisms of the PV modules. These results demonstrate that APE is a reasonable and useful index to describe the spectral irradiance distribution for evaluating the outdoor performance of PV modules.     

Considerations for the calculation of greenhouse gas reduction by photovoltaic solar energy

A CO₂ comprehensive balance within the life-cycle of a photovoltaic energy system requires careful examination of the CO₂ sinks and sources at the locations and under the conditions of production of each component, during transport, installation and operation, as well as at the site of recycling. Calculations of the possible effect on CO₂ reduction by PV energy systems may be incorrect if system borders are not set wide enough and remain on a national level, as can be found in the literature. For the examples of Brazil and Germany, the effective CO₂ reductions have been derived, also considering possible interchange scenarios for production and operation of the PV systems considering the carbon dioxide intensity of the local electricity grids. In the case of Brazil also off-grid applications and the substitution of diesel generating sets by photovoltaics are examined: CO₂ reduction may reach 26,805 kg/kW_p in that case. Doing these calculations, the compositions of the local grids and their CO₂ intensity at the time of PV grid injection have to be taken into account. Also possible changes of the generation fuel mix in the future have to be considered: During the operation time of a PV system, different kinds of power plants could be installed that might change the CO₂ intensity of the grid. In the future also advanced technologies such as thin films have to be considered.     

A novel maximum power fuzzy logic controller for photovoltaic solar energy systems

The maximum power tracking problem and efficient energy utilization of a stand-alone photovoltaic array (PVA) feeding voltage controlled linear and nonlinear loads is studied. A novel and simple on-line fuzzy logic-based dynamic search, detection and tracking controller is developed to ensure maximum power point (MPP) operation under excursions in solar insolation, ambient temperature and electric load variations. A computer simulation model of the PVA renewable utilization scheme including the effects of temperature and solar irradiation changes was developed and fully simulated. The load voltage is controlled by a DC chopper and kept constant at the required rated voltage. A permanent magnet DC motor (PMDC) driving a fan-type load was connected in parallel to an RL passive load. A speed control scheme is also used for the PMDC motor drive so that the drive can be operated at specified speeds. Different controllers have been employed in the unified PVA scheme to control three separate loads at MPP tracking condition namely voltage at load bus and speed of the PMDC motor. The main objective of the paper is to present a novel enhanced, cost-effective MPP detector (MPPD) and dynamic MPP tracking (MPPT) controller for a hybrid mix of electric loads.     

Scalable methodology for the photovoltaic solar energy potential assessment based on available roof surface area: Application to Piedmont Region (Italy)

During the last few years the photovoltaic energy market has seen an outstanding growth. According to the new directive on renewable energies of the European Commission (2009/28/EC), the European Union should reach a 20% share of the total energy consumption from renewable sources by 2020. The national overall targets impose for Italy a 17% renewable share: in case of failure the gap would be filled by importation of renewable energy from non-UE countries. The ambitious national targets and thus the continuously increasing interest on renewable fuels, require simple but reliable methods for the energy potential assessment over large-scale territories. Considering roof-top integrated PV systems, the assessment of the PV energy potential passes through the evaluation of the roof surface area available for installations. In the present paper a methodology for estimating the PV solar energy potential is presented, together with its application to Piedmont Region (North-Western Italy). The roof area suitable for solar applications, is calculated through the analysis of available GIS data. The solar radiation maps are taken from the database of the Joint Research Centre of the European Commission. Different solar energy exploitation scenarios are proposed with the relative perspective results and confidence interval. Further developments and applications of the presented methodology are finally discussed.     

Optimizing the energy and exergy of building integrated photovoltaic thermal (BIPVT) systems under cold climatic conditions

Building integrated photovoltaic thermal (BIPVT) system has the potential to become a major source of renewable energy in the urban environment. In this paper, the system has been used as the roof top of a building to generate higher electrical energy per unit area and to produce necessary thermal energy required for space heating. One-dimensional transient model has been developed using basic heat transfer equations. On the basis of this model, an analysis has been carried in order to select an appropriate BIPVT system suitable for the cold climatic conditions of India. The PV performances, net energy gain and exergy of the building are determined. The results show that for a constant mass flow rate of air the system connected in series gives a better performance whereas for a constant velocity of air flow the system connected in parallel gives a better performance. The BIPVT system, fitted on the rooftop in an effective area of 65 m², is capable of annually producing the net electrical and thermal exergies of 16,209 kW h and 1531 kW h, respectively, at an overall thermal efficiency of 53.7%.     

Measured and modelled improvement in solar energy yield from flat plate photovoltaic systems utilizing different tracking systems and under a range of environmental conditions

This work is performed to investigate the effect of using different sun tracking mechanisms on the flat plate photovoltaic system performances and the main parameters affecting the amount of their electrical energy output as well as those affecting their gains compared to the traditional fixed photovoltaic systems. To this end, five configurations of sun tracking systems and two traditional fixed panels have been considered. The sun tracking systems effect on the PV system performances is improved by using the hourly data collected over 18 days for different seasonal sky conditions. The daily cumulative electrical energy produced by the different systems have been quantified separately for each sky state and the corresponding electrical gains have then been compared to those experienced with two traditional fixed photovoltaic systems. It is found that for a completely clear day, the highest obtained gains are those related to the two-axis sun tracker systems, which decrease gradually from the inclined to the vertical rotating axis when the same optimum slope is applied and from the seasonal to the yearly optimum slope if the same rotating axis is considered. On the other hand, for the partially clear days, the gain amounts are mainly dependant on the clearness index and on the seasonal variation of day length values. For a completely cloudy day, the results show that all considered systems produced closely the same electrical energy and the horizontal position of the photovoltaic panel presented the best performance.     

Estimating potential photovoltaic yield with r.sun and the open source Geographical Resources Analysis Support System

The package r.sun within the open source Geographical Resources Analysis Support System (GRASS) can be used to compute insolation including temporal and spatial variation of albedo and solar photovoltaic yield. A complete algorithm is presented covering the steps of data acquisition and preprocessing to post-simulation whereby candidate lands for incoming solar farms projects are identified. The optimal resolution to acquire reliable solar energy outputs to be integrated into PV system design software was determined to be 1 square km. A case study using the algorithm developed here was performed on a North American region encompassing fourteen counties in South-eastern Ontario. It was confirmed for the case study that Ontario has a large potential for solar electricity. This region is found to possess over 935,000 acres appropriate for solar farm development, which could provide 90 GW of PV. This is nearly 60% of Ontario’s projected peak electricity demand in 2025. The algorithm developed and tested in this paper can be generalized to any region in the world in order to foster the most environmentally-responsible development of large-scale solar farms.     

An approach to evaluate the energy advantage of two axes solar tracking systems in Spain

The present work shows an alterative method for determining the tracking energy advantage, defined as the additional electrical energy produced by two axes tracking systems respect to fixed devices, in order to analyze the economical profitability in Spain. For this purpose, 52 main cities of this country have been analyzed. The proposed methodology starts from irradiation data, combining diffuse models and daily–hourly relations. Different types of losses have been evaluated, and the electrical behavior of the systems has been incorporated. Final annual energetic results demonstrate that two axes devices show a relevant energy advantage (higher than 20%) for most of the national territory.     

Study of hybrid energy system coupling fuel cell,solar thermal system and photovoltaic cell

The present work examines the combination of solar energy systems with Fuel cell. Indeed, fuel cells are green storage systems without any pollution effects. They are supplied by oxygen and hydrogen to produce electricity. That is why it is inescapable to find a source of hydrogen in order to use fuel cell. Several techniques can be adopted to produce hydrogen depending on the availability and the cost of the sources. One of the most utilized techniques is electrolysers. They allow to obtain hydrogen from water by several technologies among them proton exchange membrane (PEM) which is considered in this work. On the other hand, electrolysers need electrical power to operate. A green-green energy system can be constructed by using a renewable energy source to supply fuel cell trough electrolysers. A comparison between two solar systems (Photovoltaic and Parabolic Trough) coupled to fuel cell is performed. A case study on the Lebanese city of Tripoli is carried out. The study shows the performance of each of both combined systems for different parameters and proposes recommendations depending on the considered configuration.     

An application of a combined wind and solar energy system in Izmir

In this work, a combined system which is produced electrical energy from both solar radiation via solar cells and wind energy by using wind turbine was studied. For wind energy, measurements of wind velocities at 12 m height were taken. Then, these values were calculated for 42 m by using Hellmann equation. After that, wind energy converted to the electrical energy. However, value of solar radiation from solar cells was taken at the optimum slope angle of collector which provided higher energy production for each 1 h during this application. Thus, obtained data from each system were used together for finding total energy. For this study, measurements, which would be used in calculation of wind energy and solar energy were taken for four years between 1995 and 1998 in Izmir. As a result, energy of the combined system could support each other when one of them produces energy insufficiently.     

Field experience on solar electric power systems and their potential in Palestine

Palestine has a large number of rural small villages far from the national electric grids. Electrical loads in such villages are mostly small and can be covered by means of photovoltaic (PV) generators, which are economically more feasible than extending the electric grid or using diesel electric generators. Since PV has been rarely used in Palestine, this paper is devoted to investigating the potential of PV applications in Palestine, identifying the barriers for prevalence of PV applications as in other countries and demonstrating the reliability and feasibility of utilizing PV systems by presenting the test results of a PV system by supplying a rural clinic with its power demands. A method for designing the PV power system respecting the local environmental conditions is presented in this paper. The results of the measurements carried out over two years verify the reliability of the applied method. The illustrated test results show how far the PV-power generation can be matched with load demands and state of battery charge even during periods of low solar radiation. This could be achieved by respecting the local weather parameters in the illustrated sizing method. Long term field experience in designing, testing and operation of PV projects outside Palestine is presented in this paper.     

Desalination of underground brackish waters using an electrodialysis system powered directly by photovoltaic energy

The aims of this paper are: to demonstrate the feasibility of the desalination of brackish water from aquifers (total dissolved solids=2300-5100 g m⁻³) by means of an electrodialysis system powered directly by photovoltaic solar panels, and improve the mathematical model developed in a previous work in order to apply it to real brackish waters. The application of this model allows to predict the behaviour of the electrodialysis-photovoltaic system under different operational and meteorological conditions, and the time required to reach a given final concentration. Finally, the cost of electrodialysis-photovoltaic systems for small applications in isolated locations with lack of electric grid has been estimated.     

Feed-in tariff for solar photovoltaic: The rise of Japan

Japan started implementing a national Feed-In Tariff (FiT) mechanism on the 1st July 2012, which included specific payment tariffs for solar photovoltaic (PV) installations. This marks a new era in the renewable energy landscape in Japan. This paper aims at analysing the solar PV prospect in Japan, particularly in both residential and non-residential sectors. The paper presents, first, an overview of energy trends in Japan prior to the Fukushima event. This is followed by a short review of solar PV progress in the country, highlighting the major policies and programmes that have been implemented as well as the installations that have been carried out over the past two decades. Next, the financial impact of the new FiT scheme on consumers is evaluated. The financial analysis investigates the total profit, the average annual return on investment and the payback period. For a comparison purposes, a similar financial analysis is also conducted with selected countries around the world – namely Germany, Italy and the United Kingdom. The results from this analysis indicate that the new Japanese FiT rate generates a good profit, a moderate annual return on investment and an acceptable payback period, suggesting an increasing trend of solar PV uptake over the next years.     

Desalination using solar energy: Towards sustainability

This paper describes the theoretical rationale for a new low temperature phase-change desalination process, and six examples of applications to illustrate how this process can be engineered for sustainable desalination. In this process, brackish water is evaporated at near-ambient temperatures under near-vacuum pressures created by the barometric head without any mechanical energy input. Thermodynamic advantages and benefits of low temperature phase-change desalination are discussed and results from simulation studies and a prototype test system are presented. Three of the examples illustrate how the proposed process can be driven by solar energy: a) utilizing direct solar energy; b) inclusion of an external reflector; c) utilizing photovoltaic energy during non-sunlight hours. The other examples illustrate how the proposed process can be driven by waste heat: i) waste heat rejected by an absorption refrigeration unit driven by grid power; ii) waste heat rejected by an absorption refrigeration unit driven by solar collectors; and iii) waste heat rejected by an absorption refrigeration unit supported by a photovoltaic array. Merits of utilizing solar energy and process waste heat in reducing energy consumption and greenhouse gas emissions are discussed in detail.     

A two dimensional thermal network model for a photovoltaic solar wall

A two dimensional thermal network model is proposed to predict the temperature distribution for a section of photovoltaic solar wall installed in an outdoor room laboratory in Concordia University, Montréal, Canada. The photovoltaic solar wall is constructed with a pair of glass coated photovoltaic modules and a polystyrene filled plywood board as back panel. The active solar ventilation through a photovoltaic solar wall is achieved with an exhaust fan fixed in the outdoor room laboratory. The steady state thermal network nodal equations are developed for conjugate heat exchange and heat transport for a section of a photovoltaic solar wall. The matrix solution procedure is adopted for formulation of conductance and heat source matrices for obtaining numerical solution of one dimensional heat conduction and heat transport equations by performing two dimensional thermal network analyses. The temperature distribution is predicted by the model with measurement data obtained from the section of a photovoltaic solar wall. The effect of conduction heat flow and multi-node radiation heat exchange between composite surfaces is useful for predicting a ventilation rate through a solar ventilation system.     

Electrocoagulation of a synthetic textile effluent powered by photovoltaic energy without batteries: Direct connection behaviour

The feasibility of the use of an electrocoagulation system (EC) directly powered by a photovoltaic (PV) array has been demonstrated. The model pollutant used was a reactive textile dye Remazol Red RB 133. It has been proved that PV array configuration is a factor of great influence on the use of the generated power. The optimum PV array configuration must be reshaped depending on the instantaneous solar irradiation. A useful and effective methodology to adjust the EC–PV system operation conditions depending on solar irradiation has been proposed. The current flow ratio, J_v, is established as the control parameter.     

Scalable methodology for the photovoltaic solar energy potential assessment based on available roof surface area: Further improvements by ortho-image analysis and application to Turin (Italy)

The ongoing rush of the UE member states to the 2020 overall targets on the national renewable energy share (see Directive 2009/28/EC), is propelling the large exploitation of the solar resource for the electricity production. However, the incentives to the large employment of PV solar modules and the relative perspective profits, are often cause of massive ground-mounted installations. These kind of installations are obviously the preferred solution by the investors for their high economic yields, but their social impact should be also considered. Over the Piedmont Region for instance, the large proliferation of PV farms is jeopardising wide agricultural terrains and turistic areas, therefore the policy of the actual administration is to encourage the use of integrated systems in place of massive installations. For these reasons, an effort to demonstrate that the distributed residential generation can play a primary role in the market is mandatory. In our previous work “Scalable methodology for the photovoltaic solar energy potential assessment based on available roof surface area: application to Piedmont Region (Italy)”, we already proposed a basic methodology for the evaluation of the roof-top PV system potential. However, despite the total roof surface has been computed on a given cartographical dataset, the real roof surface available for PV installations has been evaluated through the assumption of representative roofing typologies and empirical coefficients found via visual inspection of satellite images. In order to overcome this arbitrariness and refine our methodology, in the present paper we present a brand new algorithm to compute the available roof surface, based on the systematical analysis and processing of aerial georeferenced images (ortho-images). The algorithm, fully developed in MATLAB®, accounts for shadow, roof surface available (bright and not), roof features (i.e. chimneys or walls) and azimuthal angle of the eventual installation. Here we apply the algorithm to the whole city of Turin, and process more than 60,000 buildings. The results achieved are finally compared with our previous work and the updated PV potential assessment is consequently discussed.