Analysis of internal helically finned tubes for parabolic trough design by CFD tools

This paper has analysed the effect of the utilization of internal finned tubes for the design of parabolic trough collectors with computational fluid dynamics tools. Our numerical approach has been qualified with the computational estimation of reported experimental data regarding phenomena involved in finned tube applications and solar irradiation of parabolic trough collector. The application of finned tubes to the design of parabolic trough collectors must take into account features as the pressure losses, thermal losses and thermo-mechanical stress and thermal fatigue. Our analysis shows an improvement potential in parabolic trough solar plants efficiency by the application of internal finned tubes.     

Infrared temperature measurements on solar trough absorber tubes

The temperature distribution on solar trough absorber tubes determines thermal losses and hotspots can lead to material stress and limit absorber tube lifetime. The concentrated solar radiation, however, makes it difficult to determine the temperature on solar absorbers. Temperature sensors that require contact to the measurement object are not appropriate and even pyrometry fails, when external light sources interfere. Only solar-blind pyrometry offers reliable temperature readings without perturbation through reflected solar radiation. This paper presents two concepts for a pyrometric solar-blind measurement on solar trough absorber tubes. One solar-blind approach is a spectral measurement range in regions, where the solar spectrum shows gaps due to the discrete absorption of the atmosphere. Another possibility for a solar-blind pyrometric temperature measurement results from the optical behavior, i.e. the distinct angle dependence of the directional reflectance and emittance of a typical selective trough absorber coating. First experimental results are shown and the accuracy and performance advantages and disadvantages of the setups are reported and discussed.     

A conceptual design of solar boiler

State-of-the-art concepts for solar thermal power systems are based on parabolic trough, tower or parabolic disks either heating molten salts, mineral oil, air or generating steam. We propose in this paper, a conceptual design of a solar boiler. This concept comes from the conventional thermal power plants boiler, with the difference that the heat comes from mirrors that concentrate the solar radiation on wall-type array of solar collectors, instead of coming from fuel flames and hot gases. In our preliminary performance, analysis of this innovative solar boiler applied to electricity production, we have found that overall efficiency of the conversion from direct solar irradiation energy to electricity is above 20%, which is comparable to the value of parabolic trough and central tower technologies. Besides that, the concept seems very robust and could overcome some drawbacks derived from pressure losses, control complexity and material thermo-mechanical stress.     

A detailed nonuniform thermal model of a parabolic trough solar receiver with two halves and two inactive ends

In this paper a detailed one dimensional nonuniform thermal model of a parabolic trough solar collector/receiver is presented. The entire receiver is divided into two linear halves and two inactive ends for the nonuniform solar radiation, heat transfers and fluid dynamics. Different solar radiation and heat transfer modes can be taken into consideration for these four different regions respectively. This enables the study of different design parameters, material properties, operating conditions, fluid flow and heat transfer performance for the corresponding regions or the whole receiver. Then the nonuniform model and the corresponding uniform thermal model are validated with known performance of an existing parabolic trough solar collector/receiver. For applications, the uniform thermal model can be used to quickly compute the integral heat transfer performance of the whole PTC system while the nonuniform thermal model can be used to analyze the local nonuniform solar radiation and heat transfer performance characteristics and nonuniform heat transfer enhancements or optimizations. Later, it could also be effectively used with an intelligent optimization, such as the genetic algorithm or the particle swarm optimization, to quickly evaluate and optimize the characteristics and performance of PTCs under series of nonuniform conditions in detail.     

Heat losses from parabolic trough solar collectors

Parabolic trough solar collector usually consists of a parabolic solar energy concentrator, which reflects solar energy into an absorber. The absorber is a tube, painted with solar radiation absorbing material, located at the focal length of the concentrator, usually covered with a totally or partially vacuumed glass tube to minimize the heat losses. Typically, the concentration ratio ranges from 30 to 80, depending on the radius of the parabolic solar energy concentrator. The working fluid can reach a temperature up to 400°C, depending on the concentration ratio, solar intensity, working fluid flow rate and other parameters. Hence, such collectors are an ideal device for power generation and/or water desalination applications. However, as the length of the collector increases and/or the fluid flow rate decreases, the rate of heat losses increases. The length of the collector may reach a point that heat gain becomes equal to the heat losses; therefore, additional length will be passive. The current work introduces an analysis for the mentioned collector for single and double glass tubes. The main objectives of this work are to understand the thermal performance of the collector and identify the heat losses from the collector. The working fluid, tube and glass temperature's variation along the collector is calculated, and variations of the heat losses along the heated tube are estimated. It should be mentioned that the working fluid may experience a phase change as it flows through the tube. Hence, the heat transfer correlation for each phase is different and depends on the void fraction and flow characteristics. However, as a first approximation, the effect of phase change is neglected. Copyright © 2013 John Wiley & Sons, Ltd.     

Effect of using nanofluids on efficiency of parabolic trough collectors in solar thermal electric power plants

In this paper, forced convection heat transfer nanofluid flow inside the receiver tube of solar parabolic trough collector is numerically simulated. Computational Fluid Dynamics (CFD) simulations are carried out to study the influence of using nanofluid as heat transfer fluid on thermal efficiency of the solar system. The three-dimensional steady, turbulent flow and heat transfer governing equations are solved using Finite Volume Method (FVM) with the SIMPLEC algorithm. The results show that the numerical simulation are in good agreement with the experimental data. Also, the effect of various nanoparticle volume fraction on thermal and hydrodynamic characteristics of the solar parabolic collector is discussed in details. The results indicate that, using of nanofluid instead of base fluid as a working fluid leads to enhanced heat transfer performance. Furthermore, the results reveal that by increasing of the nanoparticle volume fraction, the average Nusselt number increases.     

Thermal analysis of solar parabolic trough with porous disc receiver

In this paper, 3-D numerical analysis of the porous disc line receiver for solar parabolic trough collector is presented. The influence of thermic fluid properties, receiver design and solar radiation concentration on overall heat collection is investigated. The analysis is carried out based on renormalization-group (RNG) k–ε turbulent model by using Therminol-VP1 as working fluid. The thermal analysis of the receiver is carried out for various geometrical parameters such as angle (θ), orientation, height of the disc (H) and distance between the discs (w) and for different heat flux conditions. The receiver showed better heat transfer characteristics; the top porous disc configuration having w = d_i, H = 0.5d_i and θ = 30°. The heat transfer characteristic enhances about 64.3% in terms of Nusselt number with a pressure drop of 457 Pa against the tubular receiver. The use of porous medium in tubular solar receiver enhances the system performance significantly.     

A new TRNSYS component for parabolic trough collector simulation

This study describes and evaluates a new simulation component for parabolic trough collectors (PTCs). The new simulation component is implemented in the TRNSYS software environment by means of new Type that is suitable for integration into the calculation of a whole concentrating solar thermal plant, in order to evaluate the energy production of a PTC. The main advantage of the new Type is that is derived from experimental data available on efficiency Test Reports, according to the current European and International standards, rather than the theoretical approach considered in the existing parabolic trough component of TRNSYS library. The performance of the new Type has been validated with real experimental data obtained from the DISS solar test loop in Plataforma Solar de Almería, Spain. The paper describes the modelling approach, presents the comparison of simulation results with measurements taken at the DISS facility and evaluates the results.     

Parabolic trough collector with rhombus tube absorber for higher concentration ratio

In the present study, the concentration ratio of the parabolic trough collector using rhombus tube absorber has been estimated. An analytical technique has been developed to determine the optimum size of the rhombus tube absorber for given trough dimensions. The optimum size of the rhombus tube absorber is 13.8% smaller than the circular tube absorber for the LS3 trough with no change in intercept factor. The maximum improvement in the concentration ratio is found to be 31.5% for the troughs with rim angle 90° in comparison to circular tube absorber. Results also indicate that rhombus tube absorber can be employed for a range of rim angle 75 to 90 degree.

Abbreviations: CR: concentration ratio; CSP: concentrated solar power; MCRT: Monte Carlo ray tracing; PTC: parabolic trough collector     

Numerical study on coupled fluid flow and heat transfer process in parabolic trough solar collector tube

A unified two-dimensional numerical model was developed for the coupled heat transfer process in parabolic solar collector tube, which includes nature convection, forced convection, heat conduction and fluid-solid conjugate problem. The effects of Rayleigh number (Ra), tube diameter ratio and thermal conductivity of the tube wall on the heat transfer and fluid flow performance were numerically analyzed. The distributions of flow field, temperature field, local Nu and local temperature gradient were examined. The results show that when Ra is larger than 10⁵, the effects of nature convection must be taken into account. With the increase of tube diameter ratio, the Nusselt number in inner tube (Nu₁) increases and the Nusselt number in annuli space (Nu₂) decreases. With the increase of tube wall thermal conductivity, Nu₁ decreases and Nu₂ increases. When thermal conductivity is larger than 200 W/(m K), it would have little effects on Nu and average temperatures. Due to the effect of the nature convection, along the circumferential direction (from top to down), the temperature in the cross-section decreases and the temperature gradient on inner tube surface increases at first. Then, the temperature and temperature gradients would present a converse variation at θ near π. The local Nu on inner tube outer surface increases along circumferential direction until it reaches a maximum value then it decreases again.     

Optimization of parabolic trough solar collector system

Process heat produced by solar collectors can contribute significantly in the conservation of conventional energy resources, reducing CO₂ emission, and delaying global warming. One of the major problems associated with solar process heat application is fluctuation in system temperature during unsteady state radiation conditions which may cause significant thermal and operation problems. In this paper a transient simulation model is developed for analysing the performance of industrial water heating systems using parabolic trough solar collectors. The results showed that to prevent dramatic change and instability in process heat during transient radiation periods thermal storage tank size should not be lower than 14.5 l m^?2 of collector area. Small periods of radiation instability lower than 30 min do not have significant effect on system operation. During these periods when water flow rate of collector loop is doubled the time required to restore system normal operating condition increased by a ratio of 1.5. Copyright © 2005 John Wiley & Sons, Ltd.     

Modelling of parabolic trough direct steam generation solar collectors

Solar electric generation systems (SEGS) currently in operation are based on parabolic trough solar collectors using synthetic oil heat transfer fluid in the collector loop to transfer thermal energy to a Rankine cycle turbine via a heat exchanger. To improve performance and reduce costs direct steam generation in the collector has been proposed. In this paper the efficiency of parabolic trough collectors is determined for operation with synthetic oil (current SEGS plants) and water (future proposal) as the working fluids. The thermal performance of a trough collector using Syltherm 800 oil as the working fluid has been measured at Sandia National Laboratory and is used in this study to develop a model of the thermal losses from the collector. The model is based on absorber wall temperature rather than fluid bulk temperature so it can be used to predict the performance of the collector with any working fluid. The effects of absorber emissivity and internal working fluid convection effects are evaluated. An efficiency equation for trough collectors is developed and used in a simulation model to evaluate the performance of direct steam generation collectors for different radiation conditions and different absorber tube sizes. Phase change in the direct steam generation collector is accounted for by separate analysis of the liquid, boiling and dry steam zones.     

槽式太阳聚光器的研究

提出了一种低倍聚光的抛物面槽式聚光光伏发电方式.从聚光器的聚光比入手,推导抛物面槽式聚光的能流聚光比的公式,分析了能流聚光比和各个参数的关系.依据这些关系式制成的低倍聚光装置适宜于普及,可节约光伏装置成本,增加光伏发电量.     

The application of parabolic trough technology under Jordanian climate

Parabolic trough solar thermal power plants are a proven technology in the utility scale since mid of the eighties. Between 1984 and 1991 nine power plants with an overall capacity of 354 MW have been installed in the Mojave Desert in California. Since, these power plants can be equipped with a thermal storage or a fossil back-up they offer a fully dispatchable electricity generation capacity. This technology will be a very interesting near term option for countries with high solar irradiation levels and small resources of fossil fuels like Jordan.This paper, discusses the use of parabolic trough solar thermal power plants for electricity production under Jordanian climate for two different sites (Amman, and Ma'an). An analysis of the daily power output, direct normal irradiation and the efficiency for the two sites has been carried out. The results showed that Ma'an site would be preferred than Amman site, so that it is recommended to erect the Parabolic Trough Concentrator (PTC) plant in the southern region of Jordan.Also this study aims to encourage the Jordanian government and the private sector to implement the solar thermal power plants for future expansion of power sector due to the increasing electricity demand and environmental degradation.     

Design, manufacture and testing of fiberglass reinforced parabola trough for parabolic trough solar collectors

The design and manufacture of a smooth 90° rim angle fiberglass reinforced parabolic trough for parabolic trough solar collector hot water generation system by hand lay up method is described in this paper. The total thickness of the parabolic trough is 7 mm. The concave surface where the reflector is fixed is manufactured to a high degree of surface finish. The fiberglass reinforced parabolic trough was tested under a load corresponding to the force applied by a blowing wind with 34 m/s. Distortion of the parabola due to wind loading was found to be within acceptable limits. The thermal performance of the newly developed fiberglass reinforced parabolic collector was determined according to ASHRAE Standard 93 [ASHRAE Standard 93, 1986. Method of testing to determine the thermal performance of solar collectors. American Society of Heating, Refrigerating and Air-Conditioning Engineers, Atlanta, GA]. The standard deviation of the distribution of the parabolic surface errors is estimated as 0.0066 rad from the collector performance test according to ASHRAE Standard 93 (1986), which indicates the high accuracy of the parabolic surface.     

Thermodynamic analysis of a parabolic trough solar power plant integrated with a biomass-based hydrogen production system

In the current study, a solar energy power plant integrated with a biomass-based hydrogen production system is investigated. The proposed plant is designed to supply the required energy for the hydrogen production process along with the electrical energy generation. Thermochemical processes are used to obtain high-purity hydrogen from biomass-based syngas. For this purpose, the simulation of the plant is performed using Aspen HYSYS software. Thermodynamic performance evaluation of the hybrid system is conducted with exergy analysis. Based on the obtained results, the exergy efficiencies of the hydrogen production process and power generation systems are 55.8% and 39.6%, respectively. The net power output of the system is obtained to be 38.89 MWe. Furthermore, the amount of produced hydrogen in the integrated system is 7912.5 tons/year with a flow rate of 10.8 tons/h synthesis gas for 7500 h/year operation. Results show that designing and operating a hybrid high-performance energy system using two different renewable sources is an encouraging approach to reduce the environmental impact of energy conversion processes and the effective use of energy resources.     

Performance of a cylindrical parabolic trough using a fin receiver: Limb darkening effects

The distribution of local concentration ratio on a fin receiver used with cylindrical parabolic solar concentrators has been calculated analytically considering the variation of intensity over the solar disc. The effect of the pointing error of the concentrator and that of the lateral shift and tilt of the fin receiver have also been studied. The results are plotted graphically and discussed.     

Three-dimensional numerical study of heat transfer characteristics in the receiver tube of parabolic trough solar collector

The solar energy flux distribution on the outer wall of the inner absorber tube of a parabolic solar collector receiver is calculated successfully by adopting the Monte Carlo Ray-Trace Method (MCRT Method). It is revealed that the non-uniformity of the solar energy flux distribution is very large. Three-dimensional numerical simulation of coupled heat transfer characteristics in the receiver tube is calculated and analyzed by combining the MCRT Method and the FLUENT software, in which the heat transfer fluid and physical model are Syltherm 800 liquid oil and LS2 parabolic solar collector from the testing experiment of Dudley et al., respectively. Temperature-dependent properties of the oil and thermal radiation between the inner absorber tube and the outer glass cover tube are also taken into account. Comparing with test results from three typical testing conditions, the average difference is within 2%. And then the mechanism of the coupled heat transfer in the receiver tube is further studied.     

Analytic modeling of a solar power plant with parabolic linear collectors

An analytic model for a solar thermal electric generating system with parabolic trough collectors was developed. The energy conversion of solar radiation into thermal power along the absorber tube of the parabolic collector is studied, taking into consideration the non-linearity of heat losses and its dependence on the local temperature. The coupling between the collector and the thermodynamic cycle is made up of three heat exchangers, yielding the characteristic temperatures of the cycle. The conventional Rankine cycle is treated as an endo-reversible Carnot cycle, whereby the mechanical and electric power is calculated. For comparison, we refer to the Solar Electric Generating System VI (SEGS VI), installed in the Mojave desert-CA, whose solar field is composed by LS2 parabolic trough collectors. We simulated the efficiency curves of collectors LS2 with evacuated and non-evacuated absorbers and compared with experimental results. A second simulation was carried out to estimate the optimum quantity of non-evacuated LS2 collectors in series in a collectors’ row, when friction losses along the absorber tubes are considered. Also, the performance of a 30 (MWe) power plant, composed of 50 rows with 16 LS2 collectors in series (total 800 collectors) was simulated. Three fields of different collectors were considered, the first field with evacuated absorbers, the second with non-evacuated absorbers and the third with bare absorbers. Finally, the output power of the plant is analyzed as a function of the evaporation temperature of the water-vapor fluid. A large maximum of the overall cycle efficiency is found for evaporation temperatures around 320 °C. Good agreement is obtained when comparing the results of this model with experimental data belonging to the Solar Electric Generating Systems (SEGS) installed in the Mojave desert. The analytic model developed combines simplicity, precision and flexibility, making it an attractive tool for simulation and design of solar power stations.     

Real‐time thermal states monitoring of absorber tube for parabolic trough solar collector with non‐uniform solar flux

With the world energy shortage problem becoming increasingly prominent, more and more attentions have been paid to the development of renewable energies. Among these sources, solar energy has received extensive attention with its excellent characteristics. The thermal state affects the safety of the solar heat collection system. In this paper, real‐time monitoring of the input heat flux on the inside wall and the temperature field simultaneously of an absorber tube for parabolic trough solar collector were studied. Based on the measured temperatures on the outside wall, the fuzzy adaptive Kalman filter coupled with weighted recursive least squares algorithm (WRLSA) was employed to monitor the heat states of the absorber tube inversely, in which WRLSA was used to acquire the heat flux while fuzzy adaptive Kalman filter was adopted to monitor the temperature field. The method showed strong robustness to resist the ill‐posedness. Accurate monitoring results also can be acquired when there are random disturbances of the heat transfer condition on the inner wall.