Correlation between Cyclic Resistance and Shear-Wave Velocity for Providence Silts

As an alternative to a field-based liquefaction resistance approach, cyclic triaxial tests with bender elements were used to develop a new correlation between cyclic resistance ratio (CRR) and overburden stress-corrected shear-wave velocity (VS1) for two nonplastic silts obtained from Providence, Rhode Island. Samples of natural nonplastic silt were recovered by block sampling and from geotechnical borings/split-spoon sampling. The data show that the correlation is independent of the soils’ stress history as well as the method used to prepare the silt for cyclic testing. The laboratory results indicate that using the existing field-based CRR-VS1 correlations will significantly overestimate the cyclic resistance of the Providence silts. The strong dependency of the CRR-VS1 curves on soil type also suggests the necessity of developing silt-specific liquefaction resistance curves from laboratory cyclic tests performed on reconstituted samples.     

Use of Artificial Neural Networks in the Prediction of Liquefaction Resistance of Sands

A backpropagation artificial neural network (ANN) model has been developed to predict the liquefaction cyclic resistance ratio (CRR) of sands using data from several laboratory studies involving undrained cyclic triaxial and cyclic simple shear testing. The model was verified using data that was not used for training as well as a set of independent data available from laboratory cyclic shear tests on another soil. The observed agreement between the predictions and the measured CRR values indicate that the model is capable of effectively capturing the liquefaction resistance of a number of sands under varying initial conditions. The predicted CRR values are mostly sensitive to the variations in relative density thus confirming the ability of the model to mimic the dominant dependence of liquefaction susceptibility on soil density already known from field and experimental observations. Although it is common to use mechanics-based approaches to understand fundamental soil response, the results clearly demonstrate that non-mechanistic ANN modeling also has a strong potential in the prediction of complex phenomena such as liquefaction resistance.     

Effects of Nonplastic Fines on the Liquefaction Resistance of Sands

A laboratory parametric study utilizing cyclic triaxial tests was performed to clarify the effects of nonplastic fines on the liquefaction susceptibility of sands. Studies previously published in the literature have reported what appear to be conflicting results as to the effects of silt content on the liquefaction susceptibility of sandy soils. The current study has shown that if the soil structure is composed of silt particles contained within a sand matrix, the resistance to liquefaction of the soil is controlled by the relative density of the soil and is independent of the silt content of the soil. For soils whose structure is composed of sand particles suspended within a silt matrix, the resistance to liquefaction is again controlled by the relative density of the soil, but is lower than for soils with sand-dominated matrices at similar relative densities. In this case, the resistance to liquefaction is essentially independent of the amount and type of sand. These findings suggest the need for further evaluation of the effects of nonplastic fines content upon penetration resistance, and the manner in which this relationship affects the simplified methods currently used in engineering practice to evaluate the liquefaction resistance of silty soils.     

Coupled Use of Cone Tip Resistance and Small Strain Shear Modulus to Assess Liquefaction Potential

Resistance against earthquake-related liquefaction is usually assessed using relationships between an index of soil strength such as normalized cone tip resistance and the cyclic resistance ratio (CRR) developed from observed field performance. The alternative approach based on laboratory testing is rarely used, mainly because of the apprehension that laboratory results may not reflect field behavior since the quality of laboratory data is often compromised by sampling disturbance. In this study, a database of laboratory data obtained mainly from cyclic testing of frozen (undisturbed) samples and in situ index measurements from near sampling locations comprised of cone tip resistance, qc, and shear wave velocity, Vs, have been assembled. These data indicate that neither normalized cone tip resistance nor normalized shear wave velocity individually correlate well with laboratory-measured CRR. However, the ratio of qc to the small strain shear modulus, G0, relates reasonably with CRR via separate correlations depending on geologic age. The derived qc/G0-CRR relationships were also found to be consistent with earthquake field-performance case histories.     

Verification of the Soil-Type Specific Correlation between Liquefaction Resistance and Shear-Wave Velocity of Sand by Dynamic Centrifuge Test

Liquefaction of granular soil deposits is one of the major causes of loss resulting from earthquakes. The accuracy of the liquefaction potential assessment at a site affects the safety and economy of an engineering project. Although shear-wave velocity (Vs)-based methods have become prevailing, very few works have addressed the problem of the reliability of various relationships between liquefaction resistance (CRR) and Vs used in practices. In this paper, both cyclic triaxial and dynamic centrifuge model tests were performed on saturated Silica sand No. 8 with Vs measurements using bender elements to investigate the reliability of the CRR-Vs1 correlation previously proposed by the authors. The test results show that the semiempirical CRR-Vs1 curve derived from laboratory liquefaction test of Silica sand No. 8 can accurately classify the (CRR,Vs1) database produced by dynamic centrifuge test of the same sand, while other existing correlations based on various sandy soils will significantly under or overestimate the cyclic resistance of this sand. This study verifies that CRR-Vs1 curve for liquefaction assessment is strongly soil-type dependent, and it is necessary to develop site-specific liquefaction resistance curves from laboratory cyclic tests for engineering practices.     

Laboratory Investigation on Assessing Liquefaction Resistance of Sandy Soils by Shear Wave Velocity

Shear wave velocity (Vs) offers engineers a promising alternative tool to evaluate liquefaction resistance of sandy soils, and the lack of sufficient in-situ databases makes controlled laboratory study very important. In this study, semitheoretical considerations were first given based on review of previous liquefaction studies, which predicted a possible relationship between laboratory cyclic resistance ratio (CRRtx) and Vs normalized with respect to the minimum void ratio, confining stress and exponent n of Hardin equation. Undrained cyclic triaxial tests were then performed on three reconstituted sands with Vs measured by bender elements, which verified this soil-type-dependent relationship. Further investigation on similar laboratory studies resulted in a database of 291 sets of data from 34 types of sandy soils, based on which the correlation between liquefaction resistance and Vs was established statistically and further converted to equivalent field conditions with well-defined parameters, revealing that CRR will vary proportionally with (Vs1)4. Detailed comparisons with Vs-based site-specific investigations show that the present lower-bound CRR–Vs1 curve is a reliable prediction especially for sites with higher CSR or Vs1. The framework of liquefaction assessment based on the present laboratory study is proposed for engineering practice.     

Monotonic and Cyclic Liquefaction of Very Loose Sands with High Silt Content

The results from an experimental study on sands with high nonplastic silt content are presented. Drained and undrained triaxial compression tests, undrained cyclic triaxial tests, and drained∕undrained instability tests were performed on specimens of loose Nevada sand with 40% silt content. The behavior was observed to be somewhat different from previously published tests with sands at lower silt content. The greater silt content appears to provide a more volumetrically contractive response throughout the entire stress-strain curve. However, some aspects of the response were similar to sands with lower silt content. Monotonic undrained tests indicated “reverse” behavior, i.e., static liquefaction occurred at low confining pressures and increasing dilatant volume-change tendency was observed with increasing confining pressure. Analyzing the results using the concepts of steady state resulted in a unique steady-state line only when undrained tests were sheared from the same isotropic compression line. When specimens of different initial densities were tested at the same initial confining pressures, the resulting steady-state points did not fall on the same steady-state line.     

Saturation and Preloading Effects on the Cyclic Behavior of Sand

In order to study pore water pressure response and liquefaction characteristics of sand, which has previously experienced liquefaction, two series of cyclic triaxial tests were run on medium dense sand specimens. In the first test series the influence of the soil saturation under undrained cyclic loading has been studied. It summarizes results of cyclic triaxial tests performed on Hostun-RF sand at various values of the Skempton’s pore-pressure coefficient. Analysis of experimental results gives valuable insights on the effect of soil saturation on sand response to undrained cyclic paths. In the second series of tests, the preloading influence on the resistance to the sands liquefaction has been realized on samples at various histories of loading. It was found that a large preloading induces a reduction of the resistance of sands to liquefaction.     

Characterization of Liquefaction Susceptibility of Sands by Means of Extreme Void Ratios and/or Void Ratio Range

The liquefaction susceptibility of various graded fine to medium saturated sands are evaluated by stress controlled cyclic triaxial laboratory tests. Cyclic triaxial tests are performed on reconstituted specimens having global relative density of 60%. In all cyclic triaxial tests, loading pattern is selected as a sinusoidal wave form with 1.0 Hz frequency and effective consolidation pressure is chosen as 100 kPa. Liquefaction resistance is defined as the required cyclic stress ratio causing initial liquefaction in 10 cycles during the cyclic triaxial test. The results are used to draw conclusions on the effect of the extreme void ratios and void ratio range on the liquefaction resistance of various graded sands.     

Influence of Nonplastic Fines on Shear Wave Velocity-Based Assessment of Liquefaction

Many false positives (no liquefaction detected when the normalized shear wave velocity-cyclic stress ratio (Vs1-CSR) combination indicated that it should have been) are observed in the database used in the simplified liquefaction assessment procedure based on shear wave velocity. Two possible reasons for false positives are the presence of a thick surface layer of nonliquefiable soil and the effects of fines on cyclic shear resistance (CRR) and Vs1. About 67% of the false positives that could not have been caused by an overlying thick surface layer are associated with silty sands with less than 35% fines. The effects of fines on the liquefaction resistance of silty sands and on the shear wave velocity are analyzed. Theoretical CRRfield?versus?Vs1 curves for silty sands containing 0 to 15% nonplastic fines are established. They show that the theoretical CRR-Vs1 correlations for silty sands with 5 to 15% nonplastic fines are all located to the far left of the semi-empirical curves that separate liquefaction from no-liquefaction zones in the simplified liquefaction potential assessment procedures. The results suggest the currently used shear wave velocity-based liquefaction potential curves may be overly conservative when applied to sands containing nonplastic fines.     

Shear Strength and Stiffness of Silty Sand

The properties of clean sands pertaining to shear strength and stiffness have been studied extensively. However, natural sands generally contain significant amounts of silt and∕or clay. The mechanical response of such soils is different from that of clean sands. This paper addresses the effects of nonplastic fines on the small-strain stiffness and shear strength of sands. A series of laboratory tests was performed on samples of Ottawa sand with fines content in the range of 5–20% by weight. The samples were prepared at different relative densities and were subjected to various levels of mean effective consolidation stress. Most of the triaxial tests were conducted to axial strains in excess of 30%. The stress-strain responses were recorded, and the shear strength and dilatancy parameters were obtained for each fines percentage. Bender element tests performed in triaxial test samples allowed assessment of the effect of fines content on small-strain mechanical stiffness.     

Computation of Cavity Expansion Pressure and Penetration Resistance in Sands

A cavity expansion-based theory for calculation of cone penetration resistance qc in sand is presented. The theory includes a completely new analysis to obtain cone resistance from cavity limit pressure. In order to more clearly link the proposed theory with the classical cavity expansion theories, which were based on linear elastic, perfectly plastic soil response, linear equivalent values of Young's modulus, Poisson’s ratio and friction and dilatancy angles are given in charts as a function of relative density, stress state, and critical-state friction angle. These linear-equivalent values may be used in the classical theories to obtain very good estimates of cavity pressure. A much simpler way to estimate qc—based on direct reading from charts in terms of relative density, stress state, and critical-state friction angle—is also proposed. Finally, a single equation obtained by regression of qc on relative density and stress state for a range of values of critical-state friction angle is also proposed. Examples illustrate the different ways of calculating cone resistance and interpreting cone penetration test results.     

CPT-Based Evaluation of Liquefaction and Lateral Spreading in Centrifuge

Two series of centrifuge model tests were conducted using Nevada sand. Four saturated models placed in a mildly inclined laminar box and simulating a 6-m-thick deposit were shaken inducing liquefaction effects and lateral spreading. The sand was deposited at a relative density, Dr = 45 or 75%; two of the 45% models were subjected to overconsolidation or preshaking. The second series involved in-flight measurements of static cone tip penetration resistance, qc, simulating the standard cone penetration test (CPT) 36-mm cone. Values of qc increased with Dr, overconsolidation, and preshaking. A normalized resistance, qc1N, was assigned to each of the four liquefaction/lateral spreading models. Increases in Dr, overconsolidation, and preshaking decreased liquefaction and ground deformation, but relative density alone captured these effects rather poorly. Conversely, qc1N predicted extremely well the liquefaction and lateral spreading response of the four models, confirming Seed’s hypothesis to explain the success of penetration-based seismic liquefaction charts. The depth to liquefaction measured in the four centrifuge models is consistent with the field CPT liquefaction chart.     

Correcting Liquefaction Resistance for Aged Sands Using Measured to Estimated Velocity Ratio

Factors for correcting liquefaction resistance for aged sands using ratios of measured to estimated shear-wave velocity (MEVR) are derived in this paper. Estimated values of shear-wave velocity (VS) are computed for 91 penetration resistance-VS data pairs using previously published relationships. Linear regression is performed on values of MEVR and corresponding average age. Age of the sand layer is taken as the time between VS measurements and initial deposition or last critical disturbance. It is found that MEVR increases by a factor of about 0.08 per log cycle of time, and time equals about 6?years on average when MEVR equals 1 for the recommended penetration resistance-VS relationships. The resulting regression equation is combined with the strength gain equation reported by Hayati et al. 2008 in “Proc., Geotechnical Earthquake Engineering and Soil Dynamics IV,” to produce a MEVR versus deposit resistance correction relationship. This new corrective relationship is applied to create liquefaction resistance curves based on VS, standard penetration test blow count, and cone tip resistance for sands of various ages (or MEVRs). Because age of natural soil deposits is usually difficult to accurately determine, MEVR appears to be a promising alternative.     

Liquefaction Resistance of Sandy Soils under Partially Drained Condition

In order to simulate the effect of drainage on soils adjacent to gravel drains that are installed as countermeasure against liquefaction, several series of cyclic triaxial tests were performed on saturated sands under partially drained conditions. The condition of partial drainage under cyclic loading was simulated in the laboratory using triaxial testing equipment installed with a drainage control valve to precisely regulate the volume of water being drained from test specimens. Effects of both drainage conditions and loading frequencies on cyclic response were incorporated through the coefficient of drainage effect, α*. Experimental results showed that for sand exhibiting strain softening, the partially drained response was controlled by the critical effective stress ratio while for sand showing strain hardening behavior, the controlling factor was the phase transformation stress ratio. Moreover, test results indicated that the minimum liquefaction resistance under partially drained conditions can be used as a parameter to describe the liquefaction resistance of sands improved by the gravel drain method. From these results, a simplified procedure for designing gravel drains based on the factor of safety (FL) concept was proposed.     

Estimation of Footing Settlement in Sand

The settlement of foundations under working load conditions is an important design consideration. Well‐designed foundations induce stress‐strain states in the soil that are neither in the linear elastic range nor in the range usually associated with perfect plasticity. Thus, in order to accurately predict working settlements, analyses that are more realistic than simple elastic analyses are required. The settlements of footings in sand are often estimated based on the results of in situ tests, particularly the standard penetration test (SPT) and the cone penetration test (CPT). In this article, we analyze the load‐settlement response of vertically loaded footings placed in sands using both the finite element method with a nonlinear stress‐strain model and the conventional elastic approach. Calculations are made for both normally consolidated and heavily overconsolidated sands with various relative densities. For each case, the cone penetration resistance qc is calculated using CONPOINT, a widely tested program that allows computation of qc based on cavity expansion analysis. Based on these analyses, we propose a procedure for the estimation of footing settlement in sands based on CPT results.     

Pore Pressure Generation of Silty Sands due to Induced Cyclic Shear Strains

It is well established that the main mechanism for the occurrence of liquefaction under seismic loading conditions is the generation of excess pore water pressure. Most previous research efforts have focused on clean sands, yet sand deposits with fines are more commonly found in nature. Previous laboratory liquefaction studies on the effect of fines on liquefaction susceptibility have not yet reached a consensus. This research presents an investigation on the effect of fines content on excess pore water pressure generation in sands and silty sands. Multiple series of strain-controlled cyclic direct simple shear tests were performed to directly measure the excess pore water pressure generation of sands and silty sands at different strain levels. The soil specimens were tested under three different categories: (1) at a constant relative density; (2) at a constant sand skeleton void ratio; and (3) at a constant overall void ratio. The findings from this study were used to develop insight into the behavior of silty sands under undrained cyclic loading conditions. In general, beneficial effects of the fines were observed in the form of a decrease in excess pore water pressure and an increase in the threshold strain. However, pore water pressure appears to increase when enough fines are present to create a sand skeleton void ratio greater than the maximum void ratio of the clean sand.     

Liquefaction Testing of Stratified Silty Sands

The cyclic behavior of stratified silty sandy soils is at present poorly understood, yet these materials are commonly found in alluvial deposits and hydraulic fill, which have a history of liquefaction during earthquakes. The main objective of this research project was to compare the behavior of stratified and homogeneous silty sands during seismic liquefaction conditions for various silt contents and confining pressures. A comprehensive experimental program was undertaken in which a total of 150 stress-controlled undrained cyclic triaxial tests were performed. Two methods of sample preparation were used for each soil type. These methods included moist tamping (representing uniform soil conditions) and sedimentation (representing layered soil conditions). The silt contents ranged from 10 to 50%, and confining pressures in the range of 50 to 250 KPa were considered. The results indicated that the liquefaction resistances of layered and uniform soils are not significantly different, despite the fact that the soil fabric produced by the two methods of sample preparation is totally different. The findings of this study justify applying the laboratory test results to the field conditions for the range of variables studied.     

Accounting for Soil Aging When Assessing Liquefaction Potential

It has been recognized that liquefaction resistance of sand increases with age due to processes such as cementation at particle contacts and increasing frictional resistance resulting from particle rearrangement and interlocking. As such, the currently available empirical correlations derived from liquefaction of young Holocene sand deposits, and used to determine liquefaction resistance of sand deposits from in situ soil indices [standard penetration test (SPT), cone penetration test (CPT), shear wave velocity test (Vs)], are not applicable for old sand deposits. To overcome this limitation, a methodology was developed to account for the effect of aging on the liquefaction resistance of old sand deposits. The methodology is based upon the currently existing empirical boundary curves for Holocene age soils and utilizes correction factors presented in the literature that comprise the effect of aging on the in situ soil indices as well as on the field cyclic strength (CRR). This paper describes how to combine currently recorded SPT, CPT, and Vs values with corresponding CRR values derived for aged soil deposits to generate new empirical boundary curves for aged soils. The method is illustrated using existing geotechnical data from four sites in the South Carolina Coastal Plain (SCCP) where sand boils associated with prehistoric earthquakes have been found. These sites involve sand deposits that are 200,000?to?450,000?years in age. This work shows that accounting for aging of soils in the SCCP yields less conservative results regarding the current liquefaction potential than when age is not considered. The modified boundary curves indicate that old sand deposits are more resistant to liquefaction than indicated by the existing empirical curves and can be used to evaluate the liquefaction potential at a specific site directly from the current in situ properties of the soil.     

Probabilistic Models for Cyclic Straining of Saturated Clean Sands

A maximum likelihood framework for the probabilistic assessment of postcyclic straining of saturated clean sands is described. Databases consisting of cyclic laboratory test results including maximum shear and postcyclic volumetric strains in conjunction with relative density, number of stress (strain) cycles, and “index” test results were used for the development of probabilistically based postcyclic strain correlations. For this purpose, in addition to the compilation of existing data from literature, a series of stress-controlled cyclic triaxial and simple shear tests were performed on laboratory-constituted saturated clean sand specimens. The variabilities in testing conditions (i.e., type of test, consolidation procedure, confining pressure, rate of loading, etc.) were corrected through a series of correction schemes, the effectiveness of which were later confirmed by the discriminant analyses results. Volumetric and shear strain boundary curves were developed in the cyclic stress ratio versus N1,60,CS or qc,1 domain. In addition to being based on significantly extended and higher quality databases, contrary to the existing judgmentally derived deterministic ones, proposed correlations have formal probabilistic bases, and so provide insight regarding uncertainty of strain predictions or probability of exceeding a target strain value. Probabilistic uses of the proposed correlations were illustrated by three sets of examples. A companion paper applied and calibrated the proposed volumetric strain correlation to semiempirically evaluate postearthquake settlement of level, free-field sites. For the calibration, case history soil profiles, composed of a broad range of sand types and depositional characteristics, shaken by a number of earthquakes, were used. Superior predictions of field settlements by this laboratory data-based cyclic strain assessment approach were concluded to be strongly mutually supportive.