水热法在碳纤维表面生长ZnO纳米线及性能研究

采用水热法在碳纤维表面生长ZnO纳米线,通过扫描电子显微镜(SEM)、X射线光电子能谱(XPS)和SmileView软件对ZnO纳米线进行分析。XPS结果确认碳纤维表面纳米线为ZnO纳米线,SEM图片说明T700碳纤维表面ZnO纳米线取向度高于T300碳纤维表面ZnO纳米线,关于生长时间的分析表明最优值为4h。此外,通过附着生长在碳纤维表面制备了改性的ZnO纳米线,XPS测试结果表明ZnO纳米线表面涂层为CoO。     

Co^2＋掺杂ZnO纳米线的制备与光学特性的研究

在十六烷基三甲基溴化铵表面活性剂辅助下,通过水热合成法制备了Co2 掺杂ZnO纳米线.纳米线的直径为100～160nm,长度约为10μm.纳米线沿(001)方向生长.Co2 掺杂ZnO纳米线紫外-可见(UV-vis)吸收光谱曲线,显示掺杂的ZnO纳米线在200～300nm波段之间都有很强的紫外吸收,在波长360～370nm处显示很好的激子吸收,与体相的激子吸收峰(373nm)相比产生了蓝移.纳米线分别在385、409、433、462和495nm波段表现出发光特性,简略的讨论了其发光机制.     

高压PLD法生长p型钠掺杂氧化锌纳米线阵列

采用高压脉冲激光沉积法(HP-PLD)研究了压强、金催化层厚度对钠掺杂氧化锌纳米线(ZnO:Na)生长的影响, 并制备了ZnO:Al薄膜/ZnO:Na纳米线阵列同质pn结器件。实验发现, 当金膜厚度为4.2 nm, 生长压强为3.33×10⁴ Pa, 生长温度为875℃时, 可在单晶Si衬底上生长c轴取向性良好的ZnO纳米线阵列。X射线衍射和X射线光电子能谱综合分析证实了Na元素成功掺入ZnO纳米线晶格中。在低温(15 K)光致发光谱中, 观测到了一系列由Na掺杂ZnO产生引起的受主光谱指纹特征, 如中性受主束缚激子峰(3.356 eV, A0X)、导带电子到受主峰(3.312 eV, (e, A0))和施主受主对发光峰(3.233 eV, DAP)等。通过在ZnO:Al薄膜上生长ZnO:Na纳米线阵列形成同质结, 测得I-V曲线具有明显的整流特性, 证实了ZnO:Na纳米线具有良好的p型导电性能。     

反应源温度对ZnO纳米线阵列定向性及发光性能的影响

以Au薄膜为催化剂、ZnO与碳混合粉末为反应源,采用碳热还原法在单晶Si衬底上制备了ZnO纳米线阵列.通过扫描电子显微镜( SEM)、X射线衍射仪(XRD)、荧光分光光度计对样品的表征,研究了反应源温度对ZnO纳米线阵列的定向性和光致发光性能的影响.样品在源温度920℃条件下沿(002)方向择优生长,定向性最好,温度过低不利于ZnO纳米线阵列密集生长,而温度过高导致Zn原子二次蒸发,因而也不利于纳米线阵列的定向和择优生长;样品在源温度880℃有最强的近紫外带边发射,表明温度过高和过低都不利于ZnO晶体结构的优化;由于ZnO纳米线在缺氧氛围下生长,氧空位是缺陷存在的主要形式,因此所有样品都有较强的绿光发射.温度升高导致纳米线生长速度提高而增加了氧空位缺陷数量,从而使样品绿峰强度增强并在源温度920℃时达最大值,但温度的进一步升高可导致ZnO纳米线表面Zn元素的蒸发而降低氧空位缺陷的数量,从而抑制绿峰强度.     

生长温度对热蒸发法制备ZnO纳米线的结构与发光性能影响

采用无金属催化剂的简单热蒸发法,在Si(100)衬底上不同生长温度下成功地制备了高密度和大长径比的单晶ZnO纳米线。分别利用X射线衍射仪(XRD)、扫描电子显微镜(SEM-EDS)、透射电子显微镜(TEM)及荧光光谱仪表征样品的结构和发光性质。XRD和TEM研究表明,所制备的样品为沿C轴择优取向生长的单晶ZnO纳米线,具有六方纤锌矿结构。SEM和TEM研究表明,生长温度对ZnO纳米线的形貌及长径比的影响较大。当生长温度为700℃时,制备得到长径比为300(长度约为15μm,直径约为50nm)的ZnO纳米线。低于600℃时,形成花状ZnO纳米锥或 纳 米 棒。高 于700℃时,形 成 小 长 径 比 的ZnO纳米棒。此外,室温光致发光(PL)谱上出现一个强而尖锐的紫外发射峰以及一个弱而宽泛的蓝光发射峰。采用的热蒸发法制备ZnO纳米线基于气-固(VS)生长机理且该生长方法可用于大规模、低成本制备高纯度的单晶ZnO纳米材料。     

AZO晶种层对ZnO纳米线生长及紫外光电导性能的影响

采用溶液化学法实现了在Zn(NO3)2/C6H12N4混合溶液中ZnO纳米线在AZO薄膜修饰过衬底上生长。AZO薄膜由射频磁控溅射法制备,通过溅射时间和基底温度的变化改变薄膜形态,重点研究了不同薄膜形态对ZnO纳米线形貌和结构的影响,最终在溅射2h、基底温度250℃晶种上得到垂直于衬底、高度平行取向的ZnO纳米线阵列。在此基础上研究了不同形貌ZnO纳米线阵列的紫外光电导性能差异。结果表明,垂直生长的纳米线较倒伏纳米线紫外响应迅速,分析认为是紫外光照下曝光面积不同造成的。     

生长温度对热蒸发法制备ZnO纳米线的结构与发光性能影响

采用无金属催化剂的简单热蒸发法,在Si(100)衬底上不同生长温度下成功地制备了高密度和大长径比的单晶ZnO纳米线。分别利用X射线衍射仪(XRD)、扫描电子显微镜(SEM-EDS)、透射电子显微镜(TEM)及荧光光谱仪表征样品的结构和发光性质。XRD和TEM研究表明,所制备的样品为沿c轴择优取向生长的单晶ZnO纳米线,具有六方纤锌矿结构。SEM和TEM研究表明,生长温度对ZnO纳米线的形貌及长径比的影响较大。当生长温度为700℃时,制备得到长径比为300(长度约为15μm,直径约为50nm)的ZnO纳米线;低于600℃时,形成花状ZnO纳米锥或纳米棒;高于700℃时,形成小长径比的ZnO纳米棒。此外,室温光致发光(PL)谱上出现一个强而尖锐的紫外发射峰以及一个弱而宽泛的蓝光发射峰。采用的热蒸发法制备ZnO纳米线基于气-固(VS)生长机理且该生长方法可用于大规模、低成本制备高纯度的单晶ZnO纳米材料。     

CuO/ZnO复合纳米树阵列的制备及光学特性

通过热氧化法在铜基板上制备CuO纳米线,采用凝胶法制备ZnO/CuO复合纳米树阵列。通过扫描电镜(SEM)、X射线衍射(XRD)、光致发射光谱对样品结构、形貌、光学特性进行表征。结果表明,CuO/ZnO纳米树形貌规整完美,在CuO纳米线上二次生长的ZnO纳米棒具有各向晶体生长性质,CuO/ZnO复合纳米树在可见光区域出现了优越的发光性能;以甲基橙为模拟污染物,通过光催化测试表明,CuO/ZnO复合纳米树还具有卓越的光催化性能。     

MBE法生长ZnO纳米线阵列的结构和光学性能

在氧等离子体辅助的MBE系统中, 以1 nm厚的Au薄膜为催化剂, 基于气?液?固(VLS)机制实现了低温ZnO纳米线阵列在Si(111)衬底表面的生长. 通过场发射扫描电子显微镜(FE-SEM)可以观察到, ZnO纳米线阵列垂直生长在衬底上, 直径为20~30 nm. X射线衍射(XRD)和高分辨透射电镜(HRTEM)结果表明: ZnO纳米线为六方纤锌矿结构, 具有沿c轴方向的择优取向. 光致发光(PL)谱显示在380 nm附近有强烈ZnO本征发射峰, 475~650 nm可见光区域有较强的缺陷导致的发射峰.     

ZnO纳米线的制备及其光学性能

采用物理热蒸发ZnS粉的方法,制备出了大规模的线状和棒状ZnO纳米结构.借助扫描电子显微镜、透射电子显微镜、激光拉曼光谱仪以及荧光光谱仪研究了ZnO纳米线的表面形貌、内部结构及其光学性能.结果表明,所得到的ZnO纳米线是六方的单晶结构,而且具有较好的发光性能和良好的结晶性.纳米线长约2～5μm,直径约60nm,其生长机制为气-固(VS)机制.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.     

新闻(英文)

正China and Greece Sign the Standardization Cooperation Agreement Witnessed by Chinese Premier Li Keqiang and Greek Prime Minister Antonis Samaras,AQSIQ Minister Zhi Shuping and ELOT Chairman and Executive Director Angelos Tolkas signed the SAC-ELOT Standardization Cooperation Agreement.The Agreement is one of the critical cooperation documents signed during Li Keqiang’s visit in Greece,encouraging China and Greece to