Effect of polymer matrix/montmorillonite compatibility on morphology and melt rheology of polypropylene nanocomposites

In this study, Ca²⁺‐montmorillonite (Ca²⁺‐MMT) and organo‐montmorillonite (OMMT) were modified by three compatibilizers with different degrees of polarity [poly(ethylene glycol) (PEG), alkyl‐PEG, and polypropylene (PP)‐g‐PEG]. PP/MMT nanocomposites were prepared by melt blending and characterized using X‐ray diffraction and transmission electron microscopy. The results showed the degree of dispersion of OMMT in the PP/PP‐g‐PEG/OMMT (PMOM) nanocomposite was considerably higher than those in the PP/PEG/OMMT and PP/alkyl‐PEG/OMMT nanocomposites, which indicated that the dispersion was relative to the compatibility between modified OMMT and PP matrix. Linear viscoelasticity of PP/MMT nanocomposites in melt states was investigated by small amplitude dynamic rheology measurements. With the addition of the modified MMT, the shear viscosities and storage modulus of all the PP/MMT nanocomposites decreased. It can be attributed to the plasticization effect of PEG segments in the three modifiers. This rheological behavior was different from most surfactant modified MMT nanocomposites which typically showed an increase in dynamic modulus and viscosity relative to the polymer matrix. The unusual rheological observations were explained in terms of the compatibility between the polymer matrix and MMT. In addition, the mechanical properties of PP/MMT nanocomposites were improved. A simultaneous increase in the tensile strength and toughness was observed in PP/PMOM nanocomposites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Effects of different kinds of clay and different vinyl acetate content on the morphology and properties of EVA/clay nanocomposites

A series of EVA/clay nanocomposites and microcomposites have been prepared via melt-blending. Using four kinds of EVA with different vinyl acetate (VA) contents: 28, 40, 50 and 80 wt%, and four kinds of clay: three are organophilic clay (OMMT) and one unfunctionalized clay (Na-MMT), the effects of different VA content of EVA and the kinds of the clay on the morphology and properties of EVA/clay nanocomposites were systematically investigated. In previous studies, there are only two distinct nanostructures to distinguish polymer/clay nanocomposites: the intercalated and the exfoliated. But in this paper, we proposed a new nanostructure—‘the wedged’ to describe the dispersion degree of clay in nanocomposites, it means the sheets of clay were partly wedged by the chains of polymer. The wedged, the intercalated and the partially exfoliated structures of EVA/clay nanocomposites were characterized by X-ray diffraction (XRD) and by high-resolution transmission electron microscopy (HRTEM). The enhanced storage modulus of EVA/clay nanocomposites was characterized by dynamic mechanical thermal analysis (DMTA). The enhanced degree in the storage modulus of the OMMT on EVA/clay nanocomposites with the partially exfoliated and intercalated structure is much higher than that with wedged structure, and that with the higher VA content is higher than that with the lower. The thermal stabilities of EVA/clay nanocomposites were also studied by thermal gravimetric analysis (TGA).     

Structure and properties of polypropylene/clay nanocomposites compatibilized by solid‐phase grafted polypropylene

Polypropylene/organic‐montmorillonite (PP/OMMT) nanocomposites were prepared via a solid‐phase PP graft (TMPP) with a higher grafting level as the compatibilizer. The effects of the compatibilizer on the structure and properties of PP/OMMT nanocomposites were investigated. The structure of the nanocomposites were characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The results showed that when the weight ratio of TMPP and OMMT is greater than 1:1, the OMMT can be dispersed in PP matrix uniformly at the nanoscale. The mechanical properties of the nanocomposites reached a maximum when the weight ratio of TMPP and OMMT is 1:1, although more uniform dispersion was achieved at a higher content of TMPP. The mechanical properties of the nanocomposites decrease with the content of TMPP. The crystallization behavior, dynamic rheological property, and thermal stability of the nanocomposites were investigated by differential scanning calorimetry (DSC), dynamic rheological analysis, and thermal gravimetric analysis (TGA), respectively. Due to the synergistic effects of TMPP and OMMT on the crystallization of PP, the crystallization peak temperature of the nanocomposites increased remarkably compared with that of the neat PP. TMPP shows β‐phase nucleating ability and OMMT promotes the development of β‐phase crystallite. The nanocomposites show restricted melt flow and enhanced temperature sensitivity compared with the neat PP. The thermal stability of the nanocomposites is obviously improved compared with that of the neat PP. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers.     

Water absorption and hygrothermal aging study on organomontmorillonite reinforced polyamide 6/polypropylene nanocomposites

The water absorption and hygrothermal aging behavior of organomontmorillonite (OMMT) reinforced polyamide 6/polypropylene (PA6/PP ratio = 70/30), with and without maleated PP (MAH‐g‐PP), was studied at three different temperatures (30, 60, and 90°C). The water absorption and hygrothermal aging response of the composites was studied and analyzed by tensile tests and morphology assessment (scanning electron microscopy and transmission electron microscopy), indicating the effect of the immersion temperature, OMMT, and MAH‐g‐PP compatibilizer. The mathematical treatment used in analyzing the data was the single free phase model of diffusion, which assumed Fickian diffusion and utilized Fick's second law of diffusion. The kinetics of water absorption of the PA6/PP nanocomposites conformed to Fickian law behavior, whereby the initial moisture absorption follows a linear relationship between the percentage gain at any time t and t^1/2 (the square root of time), followed by saturation. It was found that the equilibrium moisture content and the diffusion coefficient are dependent on the OMMT loading, MAH‐g‐PP concentration, and immersion temperatures. Both the tensile modulus and strength of the PA6/PP nanocomposites deteriorated after being exposed to hygrothermal aging. MAH‐g‐PP acted as a good compatibilizer for PA6/PP/OMMT nanocomposites, which was attributed to its higher retention ability in modulus and strength (in the wet and redried states), lower equilibrium moisture content, and reduced water diffusivity of the nanocomposites. Morphological sketches for both uncompatibilized and MAH‐g‐PP compatibilized PA6/PP/OMMT nanocomposites, toward water uptake are proposed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 780–790, 2005     

Interfacially compatibilized LDPE/POE blends reinforced with nanoclay: investigation of morphology,rheology and dynamic mechanical properties

Morphological, melt rheological and dynamic mechanical properties of low-density polyethylene (LDPE)/ethylene–octene copolymer (POE)/organo-montmorillonite (OMMT) nanocomposites, prepared via melt compounding were studied. The XRD traces indicated different levels of intercalated structures for the nanocomposites. Addition of a compatibilizer (PE-g-MA) improved the intercalation process. TEM results revealed existence of clay layers in both phases but they were mainly localized in the elastomeric POE phase. Addition of 5 wt% OMMT to the LDPE/POE blend led to reduction in the size of the elastomer particles confirmed by AFM. The complex viscosity and storage modulus showed little effect of the presence of the clay when no compatibilizer was added. As the extent of exfoliation increased with addition of compatibilizer, the linear viscoelastic behavior of the composites gradually changed specially at low-frequency regions. The interfacially compatibilized nanocomposites with 5 wt% OMMT had the highest melt viscosity and modulus among all the studied nanocomposites and blends. Also, this particular composition showed the best improvement in dynamic storage modulus. The results indicated that clay dispersion and interfacial adhesion, and consequently different properties of LDPE/POE/clay nanocomposites, are greatly affected by addition of compatibilizer.     

Effect of exfoliated organophilic montmorillonite on the structure and conductivity of polypropylene/polyaniline composites

This study concentrates on the effect of organophilic montmorillonite (OMMT) nanolayers on conductivity, structure, morphology, and mechanical properties of the polypropylene/polyaniline (PP/PANI) composites. The composite was prepared by in situ polymerization of aniline at different composition ratios in the presence of PP powder. The structure and conductivity of ternary PP/PANI/OMMT nanocomposites were compared with those of PP/PANI composites. DC electrical conductivity measurements indicated that electrical conductivity decreased in the presence of OMMT layers. Scanning electron microscopy showed that the surface of ternary nanocomposites have more rough regions. The interaction between PANI and OMMT was confirmed by Fourier transform infrared spectroscopy. The distribution of OMMT layers in the polymer matrix, as an effective parameter on the properties of nanocomposite, was investigated and confirmed using X‐ray diffraction and transmission electron microscopy. The results showed an exfoliated array for OMMT layers in the nanocomposite structure. The shear storage modulus for PP/PANI composites was lower than that for pure PP; however, it was increased for PP/PANI/OMMT nanocomposites. The data from the tensile and izod impact strength showed that the Young's modulus and izod impact strength were increased slightly by the addition of OMMT, whereas the elongation at break was decreased. POLYM. COMPOS., 38:699–707, 2017. © 2015 Society of Plastics Engineers     

The physical and mechanical properties of beta‐nucleated polypropylene/montmorillonite nanocomposites

Polypropylene (PP) and polypropylene/polypropylene‐g‐maleic anhydride/ organomontmorillonite (PP/PP‐g‐MA/OMMT) nanocomposites were modified with 0.05 to 0.3% (w/w) of the aryl amide β‐nucleator to promote the formation of hexagonal crystal modification (β‐phase) during melt crystallization. The nonisothermal crystallization behavior of PP, PP/PP‐g‐MA/OMMT and β‐nucleated PP/PP‐g‐MA/OMMT nanocomposites were studied by means of differential scanning calorimetry. Structure‐property relationships of the PP nanocomposites prepared by melt compounding were mainly focused on the effect and quantity of the aryl amide nucleator. The morphological observations, obtained from scanning electron microscopy, transmission electron microscopy and X‐ray diffraction analyses are presented in conjunction with the thermal, rheological, and mechanical properties of these nanocomposites. Chemical interactions in the nanocomposites were observed by FT‐IR. It was found that the β‐crystal modification affected the thermal and mechanical properties of PP and PP/PP‐g‐MA/OMMT nanocomposites, while the PP/PP‐g‐MA/OMMT nanocomposites of the study gained both a higher impact strength (50%) and flexural modulus (30%) compared to that of the neat PP. β‐nucleation of the PP/PP‐g‐MA/OMMT nanocomposites provided a slight reduction in density and some 207% improvement in the very low tensile elongation at break at 92% beta nucleation. The crystallization peak temperature (T_cp) of the PP/PP‐g‐MA/OMMT nanocomposite was slightly higher (116°C) than the neat PP (113°C), whereas the β‐nucleation increased the crystallization temperature of the PP/PP‐g‐MA/OMMT/aryl amide to 128°C, which is of great advantage in a commercial‐scale mold processing of the nanocomposites with the resulting lower cycle times. The beta nucleation of PP nanocomposites can thus be optimized to obtain a better balance between thermal and mechanical properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

New toughened polypropylene/organophilic montmorillonite nanocomposites

A new toughened polypropylene (PP)/organophilic montmorillonite (OMMT) nanocomposite was obtained by melt intercalation extrusion in a twin‐screw extruder without any compatibilizer. The nanocomposites were characterized by transmission electron microscopy (TEM) observation, melt flow rate (MFR) testing, mechanical properties measurement, melting and crystallization behaviors, and thermal stability determination. TEM images revealed the existence of intercalated OMMT layers dispersed throughout the PP matrix. A clear reduction in MFR was observed as the OMMT content increased. The yield strength, elongation at yield, and initial modulus of the PP/OMMT nanocomposites increased slightly as the result of the reinforcement of the OMMT nanofiller. The ultimate value of notched impact strength of the nanocomposites was over twofold that of neat PP after incorporation with 4 wt % OMMT; meanwhile, the heat deflection temperature values showed that the thermal stability increased a little. This is a new approach for preparation for the production of a toughened PP material with a high thermal stability and rigidity. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of clay modification on the morphological,mechanical, and thermal properties of polyamide 6/polypropylene/montmorillonite nanocomposites

Polyamide 6/polypropylene (PA6/PP = 70/30 parts) blends containing 4 phr (parts per hundred resin) of organophilic montmorillonite (OMMT) were prepared by melt compounding. The sodium montmorillonite (Na‐MMT) was modified using three different types of alkyl ammonium salts, namely dodecylamine, 12‐aminolauric acid, and stearylamine. The effect of clay modification on the morphological and mechanical properties of PA6/PP nanocomposites was investigated using x‐ray diffraction (XRD), transmission electron microscopy (TEM), tensile, flexural, and impact tests. The thermal properties of PA6/PP nanocomposites were characterized using thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), and heat distortion temperature (HDT). XRD and TEM results indicated the formation of exfoliated structure for the PA6/PP nanocomposites prepared using stearylamine modified montmorillonite. On the other hand, a mixture of intercalated and exfoliated structures was found for the PA6/PP nanocomposites prepared using 12‐aminolauric acid and dodecylamine modified montmorillonite. Incorporation of OMMT increased the stiffness but decreased the ductility and toughness of PA6/PP blend. The PA6/PP nanocomposite containing stearylamine modified montmorillonite showed the highest tensile, flexural, and thermal properties among all nanocomposites. This could be attributed to better exfoliated structure in the PA6/PP nanocomposite containing stearylamine modified montmorillonite. The storage modulus and HDT of PA6/PP blend were increased significantly with the incorporation of both Na‐MMT and OMMT. The highest value in both storage modulus and HDT was found in the PA6/PP nanocomposite containing stearylamine modified montmorillonite due to its better exfoliated structure. POLYM. COMPOS., 31:1156–1167, 2010. © 2009 Society of Plastics Engineers     

Ultrasound assisted continuous‐mixing for the preparation of PP/SEBS/OMMT ternary nanocomposites

Polypropylene (PP)/polystyrene‐block‐poly(ethylene‐co‐butylenes)‐block‐polystyrene (SEBS)/organo‐montmorillonite (OMMT) nanocomposites of varying concentrations of maleic anhydride‐grafted polypropylene (PP‐g‐MA) were prepared by continuous mixing assisted by ultrasonic oscillation. The structure and morphology of nanocomposites were investigated by X‐ray diffraction (XRD), transmission electron microscopy, and scanning electron microscopy. It was found that both PP‐g‐MA and ultrasonic oscillation could enhance the intercalation and exfoliation of OMMT in PP matrix. Meanwhile, the formation of PP could be induced by ultrasonic irradiation at a power of more than 540 W. Rheological properties including complex viscosity, storage, and loss modulus of nanocomposites were increased after adding PP‐g‐MA or ultrasonic treatment. The results of mechanical properties showed that PP‐g‐MA could improve the tensile strength and tensile modulus of nanocomposites, but with the sacrifice of impact strength. This problem could be improved by ultrasound due to the reduced particle size of SEBS. However, the mechanical properties would be reduced by ultrasonic treatment with higher intensity due to the polymer degradation. Therefore, the synergistic effect of both compatibilizer and ultrasound should account for the balance between toughness and stiffness of PP/SEBS/OMMT ternary nanocomposites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41202.     

Mechanical and rheological properties of PP/SEBS/OMMT ternary composites

The microstructure and mechanical properties of polypropylene (PP)/OMMT binary nanocomposites and PP/styrene‐6‐(ethylene‐co‐butylenes)‐6‐styrene triblock copolymer (SEBS)/OMMT ternary nanocomposites were investigated using X‐ray diffraction (XRD), transmission electron microscopy (TEM), and rheology and electromechanical testing machine. The results show that the organoclay layers are mainly intercalated and partially exfoliated in the PP‐based nanocomposites. The additions of SEBS and OMMT have no significant effect on the crystallization behavior of PP. At the same time, it can be concluded that the polymer chains of PP and SEBS have intercalated into the organoclay layers and increase the gallery distance after blending process based on the analytical results from TEM, XRD, and rheology, which result in the form of a percolated nanostructure in the PP‐based nanocomposites. The results of mechanical properties show that SEBS filler greatly improve the notched impact strength of PP, but with the sacrifice of strength and stiffness. OMMT can improve the strength and stiffness of PP and slightly enhance the notched impact strength of PP/PP‐g‐MA. In comparison with neat PP, PP/OMMT, and PP/SEBS binary composites, notched impact toughness of the PP/SEBS/OMMT ternary composites significantly increase. Moreover, the stiffness and strength of PP/SEBS/OMMT ternary nanocomposites are slightly enhanced when compared with neat PP. It is believed that the synergistic effect of both SEBS elastomer and OMMT nanoparticles account for the balanced mechanical performance of the ternary nanocomposites. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Polypropylene/organically modified Sabah montmorillonite nanocomposites: Surface modification and nanocomposites characterization

The aim of the work is to extract, purify, and organically modify montmorillonite (MMT) of Lahad Datu, Sabah bentonite. The octadecylamine treated Sabah MMT (S‐OMMT) (2–8 wt%) was then melt blended with polypropylene (PP) and maleated polypropylene (PPgMAH) (10 wt%) via single screw nanomixer extruder followed by injection molding into test samples to examine the mechanical, thermal, and morphological properties of PP/S‐OMMT nanocomposites. Unmodified Sabah MMT (S‐MMT) and commercial grade MMT (Nanomer 1.30P) filled PP nanocomposites were also characterized for comparison purpose. X‐ray diffraction results showed that the interlayer spacing of S‐MMT increased after organic modification as Fourier transform infra‐red and elemental analysis evidenced the presence of octadecylamine. PP/S‐OMMT nanocomposites showed a better dispersion and strength compared to PP/Nanomer 1.30P nanocomposites due to its smaller MMT platelet size. differential scanning calorimetry and Thermogravimetry analysis revealed that the thermal stability and crystallinity of neat PP improved with the addition of all types of MMT. Dynamic mechanical analyzer showed that PP nanocomposites have higher storage modulus (E′) values than the neat PP over the whole temperature range. The new PP/S‐OMMT nanocomposites showed a comparable performance with PP/Nanomer 1.30P nanocomposites exhibiting promising future applications of S‐MMT in polymer/MMT nanocomposites. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

PP/黏土纳米复合材料的结构与性能

采用熔体插层法制备聚丙烯（PP）/有机黏土（OMMT）纳米复合材料。XRD和TEM的测试结果表明,采用熔体插层法制备的PP/OMMT复合材料是剥离型纳米复合材料。力学性能实验结果表明,相容剂的加入提高了PP与OMMT之间的相互作用,使其各项力学性能都得到了提高;PP/OMMT纳米复合材料的各项力学性能在有机黏土含量较小的情况下,就可以有较大幅度的提高;与纯PP相比,相容剂含量为10 phr、有机黏土用量为1 phr的聚丙烯基纳米复合材料具有最好的各项力学性能。     

Effects of N,N′-Ethylenebis(stearamide) on the Properties of Poly(ethylene terephthalate)/Organo-montmorillonite Nanocomposite

Poly(ethylene terephthalate)/organo-montmorillonite (PET/OMMT) nanocomposites were melt-compounded using twin screw extruder followed by injection molding. N,N′-ethylenebis(stearamide) (EBS) was selected as a dispersing agent to improve the dispersibility and exfoliation of OMMT clay in PET matrix. Morphological properties of the PET/OMMT nanocomposites were examined by using X-ray diffraction analysis, transmission electron microscopy and atomic force microscopy. Thermal properties of the nanocomposites were characterized by using dynamic mechanical thermal analysis. It was found that the OMMT are well dispersed and exfoliated in the presence of EBS. Remarkable enhancement in impact strength and storage modulus of PET/OMMT was achieved by the addition of EBS.     

Nanocomposites of silica reinforced polypropylene: Correlation between morphology and properties

Polypropylene/fumed hydrophilic silica nanocomposites were prepared via melt mixing method using a single‐screw extruder. Comparative study with and without compatibilizing copolymer agent (maleic anhydride grafted polypropylene: PP‐g‐AM) was conducted. The obtained results were interpreted in terms of silica nanoparticle–silica nanoparticle and silica nanoparticle‐polymer interactions. These results have shown that the addition of nanofillers improves the properties of the nanocomposites. From transmission electron microscopy, it was found that agglomerations of silica particles into the PP matrix increased in average size with increasing silica contents, except in presence of the copolymer. Storage modulus values of the nanocomposites measured by dynamic mechanical thermal analysis were sensitive to the microstructure of the nanocomposites. Higher silica contents resulted in higher storage modulus, revealing that the material became stiffer. By adding the compatibilizer, a further increase of storage modulus was observed due to the finer dispersion of the filler in the matrix and the increased interfacial adhesion. Crystallization rates were found to increase with the increase of silica nanoparticles as well as PP‐g‐MA content. In addition, silica nanoparticles and the compatibilizing agent present centers of germination and nucleation of crystallites. Thus, the use of the coupling agent resulted in a further enhancement of mechanical properties of the nanocomposites due to the reduction of silica agglomeration. POLYM. ENG. SCI., 54:2187–2196, 2014. © 2013 Society of Plastics Engineers     

Biodegradable poly(l-lactide)/poly(?-caprolactone)-modified montmorillonite nanocomposites: Preparation and characterization

New nanocomposites were prepared by melt blending poly(l-lactide) (PLLA), poly(?-caprolactone) (PCL), and organically modified montmorillonite (OMMT). The obtained nanocomposites showed enhanced tensile strength, modulus and elongation at break than that of PLLA/PCL blends. The dynamic mechanical analysis showed the increasing mechanical properties with temperature dependence of nanocomposites. Wide-angle X-ray diffraction analysis and transmission electron microscopy indicated that the material formed the nanostructure. Adding OMMT improved the thermal stability and crystalline abilities of nanocomposites. The morphology was investigated by environmental scanning electron microscopy, which showed that increasing content of OMMT reduces the domain size of phase-separated particles. The specific interaction between each polymer and OMMT was characterized by the Flory-Huggins interaction parameter, B, which was determined by the equilibrium melting point depression of nanocomposites. The final values of B showed that PLLA was more compatible with OMMT than PCL.     

Preparation and properties of styrene–ethylene–butylene–styrene block copolymer/clay nanocomposites: I. Effect of clay content and compatibilizer types

BACKGROUND: Polymer/clay (silicate) systems exhibit great promise for industrial applications due to their ability to display synergistically advanced properties with relatively small amounts of clay loads. The effects of various compatibilizers on styrene–ethylene–butylene–styrene block copolymer (SEBS)/clay nanocomposites with various amounts of clay using a melt mixing process are investigated. RESULTS: SEBS/clay nanocomposites were prepared via melt mixing. Two types of maleated compatibilizers, styrene–ethylene–butylene–styrene block copolymer grafted maleic anhydride (SEBS‐g‐MA) and polypropylene grafted maleic anhydride (PP‐g‐MA), were incorporated to improve the dispersion of various amounts of commercial organoclay (denoted as 20A). Experimental samples were analyzed using X‐ray diffraction and transmission electron microscopy. Thermal stability was enhanced through the addition of clay with or without compatibilizers. The dynamic mechanical properties and rheological properties indicated enhanced interaction for the compatibilized nanocomposites. In particular, the PP‐g‐MA compatibilized system conferred higher tensile strength or Young's modulus than the SEBS‐g‐MA compatibilized system, although SEBS‐g‐MA seemed to further expand the interlayer spacing of the clay compared with PP‐g‐MA. CONCLUSION: These unusual results suggest that the matrix properties and compatibilizer types are crucial factors in attaining the best mechanical property performance at a specific clay content. Copyright © 2007 Society of Chemical Industry     

Compatibilizing effect of maleated polypropylene on the mechanical properties and morphology of injection molded polyamide 6/polypropylene/organoclay nanocomposites

Polyamide 6/polypropylene (PA6/PP=70/30 parts) blends containing 4 phr (parts per hundred resin) of organophilic modified montmorillonite (organoclay) were prepared using twin screw extruder followed by injection molding. Maleated polypropylene (MAH-g-PP) was used to compatibilize the blend system. The mechanical properties of PA6/PP nanocomposites were studied through tensile and flexural tests. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to assess the fracture surface morphology and the dispersion of the organoclay, respectively. X-ray diffraction (XRD) was used to characterize the formation of nanocomposites. The thermal properties were characterized by using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The dynamic mechanical properties of PA6/PP nanocomposites were analyzed by using dynamic mechanical thermal analyzer (DMTA). The strength and stiffness of PA6/PP nanocomposites were improved significantly in the presence of MAH-g-PP. This has been attributed to the synergistic effect of organoclay and MAH-g-PP. The MAH-g-PP compatibilized PA6/PP nanocomposites showed a homogeneous morphology supporting the compatibility improvement between PA6, PP and organoclay. TEM and XRD results revealed the formation of nanocomposites as the organoclay was intercalated and exfoliated. A possible chemical interaction between PA6, PP, organophilic modified montmorillonite and MAH-g-PP was proposed based on the experimental work.     

Morphological evolution and properties of thermoplastic vulcanizate/organoclay nanocomposites

Nanocomposites composed of organoclay and thermoplastic vulcanizates (TPVs) based on uncompatibilized or compatibilized polypropylene (PP)/ethylene–propylene–diene rubber (EPDM) blends were prepared in this study. The morphology of the nanocomposites was studied with wide‐angle X‐ray diffraction and transmission electron microscopy, which suggested that the addition of the compatibilizer played a key role in determining the morphology of the composites because of their interaction with the clay surface. Scanning electron microscopy study indicated the changes in the morphology of the rubber particles. Dynamic mechanical analysis was also applied to the analysis of these phenomena. Moreover, for nanocomposites with uncompatibilized PP/EPDM blends as the matrix, the samples showed tensile enhancement compared with neat TPV. Although the addition of the compatibilizer changed tensile properties of the composites in a rather different trend, the tensile modulus increased dramatically when the compatibilizer was added. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40618.     

Effect of organoclay on the properties of maleic‐anhydride grafted polypropylene and poly(methyl methacrylate) blend

Poly(methyl methacrylate)/polypropylene (PMMA/PP) and PMMA/maleic‐anhydride grafted PP (MAPP) blends and their blend nanocomposites containing 2 wt% organoclay (Cloisite 15A, denoted C15A), prepared by a melt mixer were studied. Both X‐ray diffraction (XRD) and transmission electron microscopy (TEM) revealed exfoliated polymer blend nanocomposites. Scanning electron microscopy (SEM) studies indicated a droplet dispersion morphology for all the blends while addition of C15A into PMMA/MAPP blend resulted to a co‐continuous morphology. In fact, rheological data and thermal properties indicated that the PMMA/MAPP/C15A nanocomposite showed a better homogeneous dispersion of silicate layers than PMMA/PP/C15A nanocomposite. A Cole–Cole plot and relaxation modulus indicated a solid‐like character for PMMA/MAPP and PMMA/MAPP/C15A, while a liquid‐like behavior was noticed for PMMA/PP and PMMA/PP/C15A. The effect of an organoclay on the dynamic mechanical properties of samples was investigated using dynamic mechanical analysis (DMA) which showed a significant enhancement on the storage modulus of the PMMA/MAPP/C15A as compared to PMMA/PP/C15A . POLYM. COMPOS., 38:431–440, 2017. © 2015 Society of Plastics Engineers