Diffusion behavior of poly(ethylene imine) into keratin fibers using microspectrophotometry

In order to investigate the diffusion behavior of poly(ethylene imine) (PEI) into keratin fibers, cross‐sectional samples of bleached white human hair treated with PEI were prepared. We were successful in developing a method for analyzing the diffusion behavior of PEI into human hair, which to our knowledge is a first. The diffusion pattern of PEI into human hair, which cannot be determined by optical microscopy, can be determined by our method. After the treatment, the cross‐sectioned hair samples were dyed with Orange II and the cross‐sectional intensity scans were measured at a wavelength of 487 nm (λ_max of Orange II) with a microspectrophotometer. In our method, the diffusion pattern of PEI at pH 11.1 showed Fickian type characteristics. This suggests that the diffusion coefficient of PEI is essentially independent of the PEI concentration. By calculating the diffusion coefficient from the PEI concentration profile, the diffusion coefficient of PEI [number‐average molecular weight (M_n) = 300 and 600] into the bleached human hair was found to be on the order of 10^?10 cm²/s. In addition, the diffusion coefficient of PEI (M_n = 600) with urea added increased twofold in comparison with that of PEI without urea added. This experiment demonstrated that urea acts as a penetration accelerator for PEI. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 65–71, 2005     

The application of polyethyleneimine draw solution in a combined forward osmosis/nanofiltration system

The objective of this study is to investigate the effect of solution chemistry of branched polyethyleneimine (PEI) draw solute and to evaluate the PEI draw solute in a combined forward osmosis (FO)/nanofiltration (NF) system. Pure water was extracted from feed solution using the FO process, and the separation of pure water was achieved by the NF process. Lower molecular weight PEI showed higher water flux than higher molecular weight PEI, due to the lower internal concentration polarization caused by a higher diffusion rate and the easy permeation of pure water by lower viscosity of the draw solution (DS). The FO water flux was determined by the osmotic pressure induced by protonation/deprotonation of PEI, and the reverse draw solute flux was determined by the combination of PEI size due to the speciation and electrostatic interaction between the membrane and PEI. This study shows that the J_s/J_w value of PEI at pH 7 was smaller than those of sodium chloride and magnesium sulfate. The recovery of PEI DS using NF has a higher value (99.4%) than of sodium chloride (20.6%) and magnesium sulfate (97.0%); this means that PEI would be a promising draw solute in an FO–NF combined system for the saline water desalination. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42198.     

Kinetics of CO2 Adsorption/Desorption of Polyethyleneimine‐Mesoporous Silica

The kinetics of adsorption of CO₂ on solid sorbents based on polyethyleneimine/mesoporous silica (PEI/MPS) was studied by following the mass gain during CO₂ flow. Linear (PEI‐423) and branched (PEI‐10k) polymers were studied. The solid sorbents were synthesized by impregnating the PEI into MPS foam. The kinetics of adsorption was fitted with a double‐exponential model. In contrast, the desorption process obeyed first‐order kinetics. The activation energy of desorption of PEI‐423 was lower than that of PEI‐10k, presumably because the branched polymer required more energy to expose its nitrogen to CO₂. To increase the CO₂ sorption capacity, the MPS was treated with nonionic surfactant materials prior to impregnation with PEI. This also lowered the maximum sorption temperature and desorption activation energies.     

Phase separation behavior of poly(ether imide)/N,N‐dimethyl acetamide/nonsolvent systems

The phase separation behavior of a poly(ether imide) (PEI)/N,N‐dimethyl acetamide (DMAc)/nonsolvent system was investigated. Three kinds of nonsolvents were used in the study: H₂O, ethanol, and acetic acid (AA). It was found that the three systems (PEI/DMAc/H₂O, PEI/DMAc/ethanol, and PEI/DMAc/AA) agree with the linearized cloud point (LCP) relation. The binodal lines of the three systems were calculated according to the LCP relation. The binodal line of the PEI/DMAc/(H₂O + DMAc) system was also calculated according to the LCP relation of the PEI/DMAc/H₂O system. The phase separation of the PEI/DMAc/(H₂O + AA) system was studied, and the results agree with the LCP relation. These results can offer useful information for the establishment of dope and coagulation media using for the fabrication of a PEI membrane. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 875–881, 2003     

Fabrication of covalently bonded nanostructured thin films of epoxy resin and polydimethylsiloxane for oil adsorption

Thin films of architectures PEI(CNER_a/PDMS)_n, PEI(CNER_b/PDMS)_n, (PEI/CNER_b)_n and PEI(CNER_b/NH₂-MMT/PEI)_n have been fabricated via covalent layer-by-layer technique. Different film deposition parameters such as solvent type, polymer concentration, polymer ratio and dipping time have been optimized to achieve a uniform growth of layers. The effect of polymer concentration and dipping time on film thickness was also studied via ellipsometer. The optimized ratio of polymer concentration was 1:1 and 1:2 for PEI(CNER_a/PDMS)_n and PEI(CNER_b/PDMS)_n, respectively. AFM analysis indicated that the films were homogeneous while contact angle measurements revealed that although films were hydrophobic in nature yet they have wetting property due to the presence of hydroxyl groups formed during curing process. These epoxy-based multilayers have shown significant oil adsorption capacity. All the fabricated films qualify scotch tape test and were found resistant towards strong acids, bases and organic solvents.     

Liquid-liquid phase separation and crystallization behavior of poly(ethylene terephthalate)/poly(ether imide) blend

The liquid-liquid (L-L) phase separation and crystallization behavior of poly(ethylene terephthalate) (PET)/poly(ether imide) (PEI) blend were investigated with optical microscopy, light scattering, and small angle X-ray scattering (SAXS). The thermal analysis showed that the concentration fluctuation between separated phases was controllable by changing the time spent for demixing before crystallization. The L-L phase-separated specimens at 130 °C for various time periods were subjected to a temperature-jump of 180 °C for the isothermal crystallization and then effects of L-L phase separation on crystallization were investigated. The crystal growth rate decreased with increasing L-L phase-separated time (t_s). The slow crystallization for a long t_s implied that the growth path of crystals was highly distorted by the rearrangement of the spinodal domains associated with coarsening. The characteristic morphological parameters at the lamellar level were determined by the correlation function analysis on the SAXS data. The blend had a larger amorphous layer thickness than the pure PET, indicating that PEI molecules in the PET-rich phase were incorporated into the interlamellar regions during crystallization.     

The effect of confinement in nanoporous polymers on the glass transition temperature

The glass transition temperature (T_g) of nanoporous polyetherimide (PEI) and PEI thin films was investigated. The T_g decreased from its bulk value in both of these confined systems. Monte Carlo simulations were performed to calculate the nearest neighbor pore-to-pore distances in the nanoporous PEI. A quantitative analogy between the nanoporous PEI and PEI thin films is proposed through an equivalence of nearest neighbor pore-to-pore distances and thin film thickness. The effect of confinement is believed to be due to the interface regions, which possess higher chain mobility than the bulk. When these high mobility interface regions are sufficiently close together, the excess mobility at the interface region affects the dynamics of the system by restraining percolation of the slow domains resulting in the observed decrease in T_g.     

Phase and crystallization behavior of solution-blended poly(ether ether ketone) and poly(ether imide)

Results on solution-blended poly(ether ether ketone) (PEEK) and poly(ether imide) (PEI) blends are reported. Dichloroacetic acid was used as the cosolvent for blending. PEEK and PEI are confirmed to be miscible in the melt. The glass transition, T_g, behavior obeys the simple Fox equation or the Gordon-Taylor equation with the adjustable coefficient k = 0.86. This agrees with prior data on melt-blended PEEK/PEI blends. The T_g width of the amorphous PEEK/PEI blends was found to be broader than that of the pure components. The maximum broadening is about 10°C. The specific volume of the amorphous PEEK/PEI blends shows a slight negative deviation from linearity, indicating favorable interaction between PEEK and PEI. The spherulitic growth and resultant blend morphology at 270°C were studied by a cross-polarized optical microscope. The radial growth rate of PEEK spherulites formed from the miscible melt at 270°C decreases from 3.04 μm/min for PEEK/PEI 90/10 blend to 0.77 μm/min for PEEK/PEI 70/30 blend. The decrease in crystalization rate of PEEK from PEEK/PEI blends is attributable to the increase in blend T_g. A linear growth was observed for PEEK spherulites formed from miscible melt at 270°C in the early growth stage. The spherulitic growth deviated from linearity in the late stage of growth. PEEK spherulites formed from the miscible PEEK/PEI melt at 270°C are essentially volume-filling. The branches of the spherulites become more clear for PEEK spherulites formed from the blend than that formed from pure PEEK melt.     

Phase separation of poly(ether sulfone imide) modified epoxy resin

Poly(ether sulfone imide)s (PEI) with molecular weight M_n ∼ 10⁴ were synthesized from 3,3′,4,4′-benzophenone tetracarboxylic dianhydride and amine terminated poly(ether sulfone) having molecular weights ranging from M_n ∼ 400 to M_n ∼ 4000. Thus, the PEIs had the same molecular weight but various imide and ether sulfone contents. The PEIs were mixed with a stoichiometric mixture of diglycidyl ether bis-phenol-A (DGEBA)/diamino diphenyl sulfone (DDS). The effect of PEI on the curing reaction of DGEBA/DDS and the morphology of the polymer blend were studied by differential scanning calorimetry (DSC) and optical microscopy. In the DGEBA/DDS/PEI blend with a fixed PEI molecular weight and PEI concentration but with various imide content, the experimental data revealed the PEI with a higher content of ether sulfone had a lower T_g and a better compatibility with solvents and epoxy resins; the curing reaction rate of DGEBA/DDS/PEI was faster for PEI with a higher imide content; the DSC data of cured DGEBA/DDS/PEI showed two T_gs, indicating phase separation between PEI and cured epoxy resins; and the data of optical microscopy showed that the compatibility of PEI with epoxy resins increased with the content of ether sulfone in PEI. © 1996 John Wiley & Sons, Inc.     

Fabrication and characterization of polyetherimide/polyvinyl acetate polymer blend membranes for CO2/CH4 separation

This article presents fabrication, characterization, and performance evaluation of polyetherimide (PEI)/polyvinyl acetate (PVAc) blend membranes. Polymer blend membranes with various blend ratios of PEI/PVAc were prepared by solution casting and evaporation technique. Morphology and miscibility of polymer blend membranes were characterized by field emission scanning electron microscope (FESEM) and differential scanning calorimetry (DSC), respectively. The interaction between blend polymers was analyzed by FTIR analysis. Gas separation performance was evaluated in terms of permeability and selectivity. FESEM results revealed that pure polymer and blend membranes were homogeneous and dense in structure. A single glass transition temperature of polymer blend membranes was found in DSC analysis which indicated the miscibility of PEI/PVAc blend. FTIR analysis confirmed the presence of molecular interaction between blend polymers. The permeation results showed that the presence of PVAc (3 wt%) in blend membranes has improved CO₂ permeability up to 95% compared to pure PEI membrane. In addition, CO₂/CH₄ selectivity was found to be 40% higher than pure PEI membrane. This study shows that blending a small fraction of PVAc can improve the gas separation performance of PEI/PVAc blend membranes. POLYM. ENG. SCI., 59:E293–E301, 2019. © 2018 Society of Plastics Engineers     

Relationship between physical properties and chemical structures of poly(ethylene terephthalate-co-ethylene isophthalate)

A series of copolyesters based on different ratios of polyethylene terephthalate (PET) to polyethylene isophthalate (PEI) have been synthesized. With the involvement of PEI, the copolyesters become less crystallizable and even amorphous when PEI content is above 20%. The WAXD profiles of the crystallizable copolyesters infer that the crystals come from PET homopolymer. DSC cooling runs indicated that the copolyesters with PEI no more than 15% are easily crystallizable, while the copolyester with 20% PEI is not easily crystallized at a cooling rate above 5°C/min. Heating runs indicated that the copolyesters with PEI below 20% show melting processes. Nonuniform results were provided by WAXD and DSC, however, the effect of PEI on the ability of crystallization was deduced similarly from WAXD and DSC. Glass transition temperatures have been measured by DSC. Due to the flexibility of PEI chain, glass transition temperatures of the copolyesters decrease linearly with increasing composition of PEI as predicted by the principle of additive contribution. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 1191–1195, 1999     

Self‐assembly of alginate/polyethyleneimine multilayer onto magnetic microspheres as an effective adsorbent for removal of anionic dyes

A novel magnetic adsorbent alginate/polyethyleneimine (ALG/PEI)_n/MN was developed for removal of anionic dyes from aqueous solution in this study. (ALG/PEI)_n/MN was prepared by depositing ALG/PEI multi‐layers onto amine‐modified Fe₃O₄ microspheres through layer‐by‐layer method. The morphologies and structures of the adsorbent were characterized by scanning electron microscopy, X‐ray diffractometer, and Fourier transform infrared spectrometer, respectively, and its performance in adsorption of anionic dye (acid orange 10, AO10) under varied experimental conditions were also investigated. The results revealed that the uptake capacity of AO10 by (ALG/PEI)_n/MN increased with the number of coated (ALG/PEI) bilayer on the adsorbents, and the maximum adsorption capacity for AO10 by (ALG/PEI)₄MN was 246.3 mg g^?1 at 25 °C. The adsorption process was exothermic and well described by the pseudo‐second order kinetic model and the Langmuir isothermal model. Moreover, (ALG/PEI)₄/MN showed good reusability and excellent magnetic separability. All the results demonstrate that (ALG/PEI)₄/MN is a potential recyclable adsorbent for removal of anionic dyes from wastewater. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45876.     

Supramolecular complexes: lamellar structure and crystalline transformation

Interfacial reaction of highly-branched polyethyleneimine (PEI) with octadecanoic acid (OA) was performed to prepare a series of supramolecular complexes (PEI(OA)_x). The complexes at solid state have typical lamellar structure, and the interlamellar distance can be modulated by the OA content. The long period values of the supramolecular complexes measured by SAXS were found to be dependent on the compositions, which are in good consistency with those measured by TEM. For example, the long period values from SAXS for PEI(OA)_0.76, PEI(OA)_1.03, and PEI(OA)_1.67 were 46.5, 62.7, and 56.2 Å, respectively. The corresponding data from TEM were 45.7, 60.7, and 56.6 Å, respectively. A model was proposed for the construction mode of the side alkyl chains (crystallization region) associated with PEI backbone (amorphous region), in which the side alkyl chains were arranged to be ‘end-to-end’ packing for the x=1 complex, while an ‘interdigitated structure’ of the side alkyl chains was deduced for the x>1 and x<1 complexes. Temperature variable FT-IR combination investigation of the scissoring band, rocking band, and stretching band of methylene (CH₂) and vibrational band of carbonyl group (CO) indicated that the crystalline form of the crystallization region in the lamellae can be transformed from orthorhombic to hexagonal with the temperature increasing, and vice versa.     

A systemic gene vector constructed by zwitterionic polymer modified low molecular weight PEI

Good blood compatibility and long-term circulation are very important to polycationic systemic gene vectors. In this work, polysulfobetaine-modified low molecular weight polyethyleneimine (LMW PEI, 1.8k) was synthesized and investigated as a vector for gene delivery in vitro and in vivo. PHEAA-b-PMPDSAH was synthesized via atomic transfer radical polymerization method, and then LMW PEI was grafted to PHEAA-b-PMPDSAH by an amido–hydroxy reaction. Incorporation of PMPDSAH into PEI was shown to retain the uncompromised ability to condense DNA into nanocomplexes. MTT assays revealed that the cytotoxicity of LMW PEI-PHEAA-b-PMPDSAH/DNA complexes was lower than that of PEI (25k)/DNA and LMW PEI-PHEAA/DNA complexes. LMW PEI-PHEAA-b-PMPDSAH₅₀ was much superior to PEI (25k) in mediating gene transfection in the presence of 10% serum. At higher serum contents, the transfection of LMW PEI-PHEAA and PEI (25k) was deteriorated, whereas LMW PEI-PHEAA-b-PMPDSAH₅₀ still retained better transfection efficiency, 8-fold more effective than PEI (25k). The expression of red fluorescence protein (RFP) was evaluated by small animal in vivo fluorescence imaging system and the results showed that the expression of RFP was much higher in the mice injected with LMW PEI-PHEAA-b-PMPDSAH₅₀/pDNA-RFP than with LMW PEI-HEAA/pDNA-RFP. Both in vitro and in vivo results suggested that LMW PEI-PHEAA-b-PMPDSAH_X copolymer holds a great potential as a vector for systemic gene therapy.     

Synthesis and structural characterization of novel bionanocomposite poly(ester-imide)s containing TiO2 nanoparticles, S-valine, and l-tyrosine amino acids moieties

The incorporation of different percents of titanium dioxide (TiO₂) nanoparticles into optically active poly(ester-imide) (PEI), afforded an opportunity to prepare several novel PEI/TiO₂ bionanocomposites (BNC)s. To this point, firstly PEI was synthesized via direct polyesterification of chiral diacid monomer and an optically active phenolic diol using tosyl chloride/pyridine/N,N-dimethylformamide system as a condensing agent. Novel BNC polymers containing TiO₂ nanoparticles were synthesized through ultrasonic irradiation method. With the aim of γ-amidopropyl-triethoxylsilicane as a coupling agent, the surface of nanoscale TiO₂ was modified to decrease aggregation of nanoparticles in polymer matrix. The obtained PEI/TiO₂ BNCs were characterized with FT-IR, thermogravimetric analysis (TGA), scanning electron microscopy, X-ray diffraction, and transmission electron microscopy (TEM) techniques. Consequently, TEM image showed that the nanoparticles of smaller than 50 nm in diameter were uniformly dispersed in the polymer matrix. TGA data demonstrated that new synthesized PEI/TiO₂ BNCs are more thermally stable in compare to pure PEI.     

Efficient dispersants for the dispersion of gallium zinc oxide nanopowder in aqueous suspensions

Appropriate dispersants for the dispersion of gallium zinc oxide (GZO) nanopowder in aqueous suspensions were identified in this study. The dispersion efficiencies and stabilization mechanisms of water‐based dispersants ammonium poly(acrylic acid) (PAA–NH₄), an anionic polyelectrolyte, and polyethylenimine (PEI), a cationic polyelectrolyte, were compared. The experimental analyses of rheology and sedimentation showed that both PAA–NH₄ and PEI were good dispersants for the dispersion of GZO. Theoretical calculations based on Derjaguin‐Landau‐Verwey‐Overbeek theory revealed that the stabilization mechanism of PEI was mainly related to the steric effect, and a very low molecular weight of 1800 g/mol was insufficient for powder stabilization. GZO was well dispersed by PEI with high molecular weight of 10 000 g/mol, but agglomeration occurred when too much PEI was added. Compared with PEI, PAA–NH₄ was more efficient because of its high contribution to the increase in electrostatic repulsion. Based on theoretical considerations on both steric and electrostatic effects, namely, the electrosteric stabilization mechanism, PAA–NH₄ is optimal for the dispersion of GZO nanopowder in aqueous suspensions.     

Reorganization of the chain packing between poly(ethylene isophthalate) chains via coalescence from their inclusion compound formed with γ‐cyclodextrin

Amorphous poly(ethylene isophthalate) (PEI) was synthesized, and was used for preparing an inclusion compound (IC) with γ‐cyclodextrin (γ‐CD). Coalesced polymer was produced by washing the PEI‐γ‐CD‐IC with hot water. Wide angle X‐ray diffraction, Fourier transform infrared, and differential scanning calorimetry analyses were employed to verify formation of PEI‐γ‐CD‐IC and to compare the as‐synthesized and coalesced PEI samples. These observations suggested that the conformations and morphology/chain‐packing of PEI were changed via coalescence from its γ‐CD inclusion compound. The glass‐transition temperature of the amorphous coalesced PEI is 15–20°C higher than the T_g observed for the as‐synthesized sample, even when observed in the second heat after cooling from well above T_g at 260°C. The amorphous as‐synthesized PEI retains its randomly‐coiling structure, while coalesced PEI has at least partially retained, the highly extended and parallel chains from the narrow channels of the inclusion compound, resulting in better/tighter packing among the PEI chains manifested by a higher T_g. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 6049–6053, 2006     

Boosting solubility performance of supercritical CO2 via ethanol toward fabrication of polyetherimide/carbon fiber composite foam with three-dimensional geometry shape

The demand for light-weight, high-performance polymeric foam material, and part soars to meet the requirements of the national economy and the high-tech industries. Currently, foaming technologies are inadequate to fabricate these advanced materials. In this study, polyetherimide/carbon fiber (PEI/CF) foam was prepared by pressure-induced batch foaming technology with the supercritical CO₂ (scCO₂) and ethanol (EtOH) as the physical foaming agent and co-foaming agent, respectively. The presence of EtOH was verified to enhance the solubility of scCO₂ and increase the interaction energies between PEI molecular chain and CO₂/EtOH foaming agent, the expansion ratio of PEI pellets, as a result, was effectively improved from 1.3 to 7.5. Using the stainless mold-assisted sinter molding, numerous PEI or PEI/CF pellets was simultaneously foamed and squeezed into three-dimensional (3D) geometry shape. The cell morphology tests indicated that the CF, served as the nucleating agent, cannot only facilitate the formation of denser microcellular structure, but also improve the mechanical performance of the final foam product. As a model system, PEI/CF foam product with a density of 320 kg/m³ was successfully obtained, the compression and tensile strength of which were 11.6 and 9.7 MPa, respectively, as proved by the mechanical performance measurements.     

Thermal properties of melt‐blended poly(ether ether ketone) and poly(ether imide)

The thermal properties of blends of poly(ether ether ketone) (PEEK) and poly(ether imide) (PEI) prepared by screw extrusion were investigated by differential scanning calorimetry. From the thermal analysis of amorphous PEEK–PEI blends which were obtained by quenching in liquid nitrogen, a single glass transition temperature (T_g) and negative excess heat capacities of mixing were observed with the blend composition. These results indicate that there is a favorable interaction between the PEEK and PEI in the blends and that there is miscibility between the two components. From the Lu and Weiss equation and a modified equation from this work, the polymer–polymer interaction parameter (χ₁₂) of the amorphous PEEK–PEI blends was calculated and found to range from −0.058 to −0.196 for the extruded blends with the compositions. The χ₁₂ values calculated from this work appear to be lower than the χ₁₂ values calculated from the Lu and Weiss equation. The χ₁₂ values calculated from the T_g method both ways decreased with increase of the PEI weight fraction. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 733–739, 1999     

Preparation of NaA Zeolite Membranes Using Poly(Ethyleneimine) as Buffer Layer,and Study of Their Permeation Behavior

Zeolite NaA membranes were prepared hydrothermally by secondary crystallization process at different temperatures (55°C–75°C) on porous α‐alumina‐based support tubes (inner side) precoated with poly(ethyleneimine) (PEI) buffer layer and NaA seed particles. The NaA seed crystals synthesized at 65°C/2 h in the size range 100–200 nm having BET surface area of 71.57 m²g^?1 were used for secondary crystallization of the membranes. The secondary crystallization at 65°C for (4 + 4) h (double‐stage) showed highly dense NaA grains in the microstructure of the membrane with a thickness of 5 μm. It rendered the permeance values of 50.6 × 10^?8, 2.47 × 10^?8, and 0.55 × 10^?8 molm^?2s^?1Pa^?1 for H₂, N₂, and CO₂, respectively, with their permselectivity of 20.48 (H₂/N₂), 92 (H₂/CO₂), and 4.49 (N₂/CO₂). A tentative mechanism was illustrated for the interaction of PEI with the support substrate and NaA seed crystals.