Mechanical properties of SiCf/SiC composites with alternating PyC/BN multilayer interfaces

Alternating pyrolytic carbon/boron nitride (PyC/BN)_n multilayer coatings were applied to the KD–II silicon carbide (SiC) fibres by chemical vapour deposition technique to fabricate continuous SiC fibre-reinforced SiC matrix (SiC_f/SiC) composites with improved flexural strength and fracture toughness. Three-dimensional SiC_f/SiC composites with different interfaces were fabricated by polymer infiltration and pyrolysis process. The microstructure of the coating was characterised by scanning electron microscopy, X–photoelectron spectroscopy and transmission electron microscopy. The interfacial shear strength was determined by the single-fibre push-out test. Single-edge notched beam (SENB) test and three-point bending test were used to evaluate the influence of multilayer interfaces on the mechanical properties of SiC_f/SiC composites. The results indicated that the (PyC/BN)_n multilayer interface led to optimum flexural strength and fracture toughness of 566.0?MPa and 21.5?MPa?m^1/2, respectively, thus the fracture toughness of the composites was significantly improved.     

Microstructure and mechanical properties of quasi-isotropic chopped fiber-reinforced PyC–SiC matrix composite prepared by novel nondamaging method

In this work, quasi-isotropic chopped carbon fiber-reinforced pyrolytic carbon and silicon carbide matrix (C_f/C–SiC) composites and chopped silicon carbide fiber-reinforced silicon carbide matrix (SiC_f/SiC) composites were prepared via novel nondamaging method, namely airlaid process combined with chemical vapor infiltration. Both composites exhibit random fiber distribution and homogeneous pore size. Young's modulus of highly textured pyrolytic carbon (PyC) matrix is 23.01 ± 1.43 GPa, and that of SiC matrix composed of columnar crystals is 305.8 ± 9.49 GPa in C_f/C–SiC composites. Tensile strength and interlaminar shear strength of C_f/C–SiC composites are 52.56 ± 4.81 and 98.16 ± 24.62 MPa, respectively, which are both higher than those of SiC_f/SiC composites because of appropriate interfacial shear strength and introduction of low-modulus and highly textured PyC matrix. Excellent mechanical properties of C_f/C–SiC composites, particularly regarding interlaminar shear strength, are due to their quasi-isotropic structure, interfacial debonding, interfacial sliding, and crack deflection. In addition to the occurrence of crack deflection at the fiber/matrix interface, crack deflection in C_f/C–SiC composites takes also place at the interface between PyC–SiC composite matrix and the interlamination of multilayered PyC matrix. Outstanding mechanical properties of as-prepared C_f/C–SiC composites render them potential candidates for application as thermal structure materials under complex stress conditions.     

High-temperature mechanical properties and oxidation resistance of SiCf/SiC ceramic matrix composites with multi-layer environmental barrier coatings for turbine applications

Continuous silicon carbide fiber reinforced silicon carbide (SiC_f/SiC) ceramic matrix composites are considered promising materials as high-temperature components of advanced aero-engines. However, due to their susceptibility to oxidation and corrosion at high temperature, environmental barrier coatings (EBCs) must be applied on the surface of SiC_f/SiC. In this study, Si/Y₂SiO₅/LaMgAl₁₁O₁₉ (LMA) multi-layer EBCs were fabricated to protect SiC_f/SiC by using atmospheric plasma spraying (APS). The high-temperature tensile fatigue performance of SiC_f/SiC with and without EBCs was evaluated. The results indicated that EBCs significantly improved the tensile fatigue properties of SiC_f/SiC at high temperature in air atmosphere. Meanwhile the bending strength of specimens after isothermal aging or not was also tested. The multi-layer EBCs in this study may be a promising EBCs system for SiC_f/SiC after some improvements.     

The mechanical,thermophysical and electromagnetic properties of UD SiCf/SiC composites in different directions

Unidirectional (UD) silicon carbide (SiC) fiber-reinforced SiC matrix (UD SiC_f/SiC) composites with CVI BN interphase were fabricated by polymer infiltration-pyrolysis (PIP) process. The effects of the anisotropic distribution of SiC fibers on the mechanical properties, thermophysical properties and electromagnetic properties of UD SiC_f/SiC composites in different directions were studied. In the direction parallel to the axial direction of SiC fibers, SiC fibers bear the load and BN interphase ensures the interface debonding, so the flexural strength and the fracture toughness of the UD SiC_f/SiC composites are 813.0 ± 32.4 MPa and 26.1 ± 2.9 MPa·m^1/2, respectively. In the direction perpendicular to the axial direction of SiC fibers, SiC fibers cannot bear the load and the low interfacial bonding strengths between SiC fiber/BN interphase (F/I) and BN interphase/SiC matrix (I/M) both decrease the matrix cracking stress, so the corresponding values are 36.6 ± 6.9 MPa and 0.9 ± 0.5 MPa?m^1/2, respectively. The thermal expansion behaviors of UD SiC_f/SiC composites are similar to those of SiC fibers in the direction parallel to the axial direction of SiC fibers, and are similiar to those of SiC matrix in the direction perpendicular to the axial direction of SiC fibers. The total electromagnetic shielding effectiveness (EM SE_T) of UD SiC_f/SiC composites attains 32 dB and 29 dB when the axial direction of SiC fibers is perpendicular and parallel to the electric field direction, respectively. The difference of conductivity in different directions is the main reason causing the different SE_T. And the dominant electromagnetic interference (EMI) shielding mechanism is absorption for both studied directions.     

The effects of preparation temperature on the SiCf/SiC 3D4d woven composite

Continuous silicon carbide fiber reinforced silicon carbide matrix (SiC_f/SiC) composites have promising applications in aero-engine due to their unique advantages, such as low density, high modulus and strength, outstanding high temperature resistance and oxidation resistance. As SiC fibers are main reinforcements in SiC_f/SiC composites, the crystallization rate and initial damage degree of SiC fibers are seriously influenced by preparation temperatures of SiC_f/SiC composites, namely mechanical properties of SiC fibers and SiC_f/SiC composites are influenced by preparation temperatures. In this paper, KD-II SiC fibers were woven into 3D4d preforms and SiC matrix was fabricated by PIP process at 1100 °C, 1200 °C, 1400 °C and 1600 °C. Digital image correlation (DIC) method was adopted to measure the uniaxial tensile properties of these SiC_f/SiC composites. In addition, finite element method (FEM) based on representative volume element (RVE) was adopted to predict the mechanical properties of SiC_f/SiC composites. The good agreements between numerical results and experimental results of uniaxial tensile tests verified the validity of the RVE. In last, the transverse tensile, transverse shear, uniaxial shear properties were predicted by this method. The predicted results illustrated that axial tensile, transverse tensile and axial shear properties were greatly influenced by the preparation temperatures of SiC_f/SiC composites while transverse shear properties were not significantly various. And the mechanical properties of SiC_f/SiC composites peaked at 1200 °C among these four temperatures while their values reached their lowest points at 1600 °C because of thermal damage and brittle failure of SiC_f/SiC composites.     

Effect of heat treatment on the microstructure and strength of yttrium silicate matrix-modified SiCf/SiC composites

Yttrium silicate was introduced into the matrix of SiC_f/SiC composites via the slurry impregnation and reactive chemical vapor infiltration (RCVI) methods to improve the water and oxygen corrosion resistance of the modified composite materials. The effects of heat treatment on the modified matrix and strength of the composites were systematically investigated. The results showed that the modified matrix was composed of a mixture of yttrium monosilicate, yttrium disilicate, and silicon carbide. The modified yttrium silicate matrix (named Y-Si-O matrix) and the silicon carbide matrix were laminated and well combined. After heat treatment, the amount of Y-Si-O in the mixed matrix increased. The modified composites with yttrium silicate had a similar flexural strength as SiC_f/SiC composites (∼400 MPa). After treated at 1000 °C – 1300 °C, the strength of the modified composites increased by 17 %–26 %. The highest strength was measured for composites treated at 1200 °C.     

Effects of in situ synthesis of CNTs/SiCw on microstructure and properties of Al2O3–SiC–C composites

Al₂O₃–SiC–C composites were prepared using tabular corundum, ball pitch and silicon carbide as the main raw materials. The carbon nanotubes (CNTs) and SiC whiskers (SiC_w) were in situ synthesized and their effects on the thermo–mechanical properties of Al₂O₃–SiC–C composites have been studied. The experimental results indicated that the high yield of SiC_w and CNTs with large aspect ratio could be obtained due to addition of Ni(NO₃)₂·6H₂O as catalyst in the composites. The cold modulus of rupture values were increased by 24% to 7.2 MPa, and the flexural modulus was increased from 19 GPa to 24 GPa. Additionally, the hot modulus of rupture reached a maximum value of 3.6 MPa, which presented a 71% increase over that of composites without catalyst. After three thermal shock cycles, the residual cold crush strength was improved from 57.1% to 76.9%. It is believed that the enhancement in the thermo-mechanical properties of Al₂O₃–SiC–C composites could be attributed to the reinforcement effect of SiC_w and CNTs.     

Effect of oxidation treatment on KD–II SiC fiber–reinforced SiC composites

Continuous silicon carbide fiber–reinforced silicon carbide matrix (SiC_f/SiC) composites have developed into a promising candidate for structural materials for high–temperature applications in aerospace engine systems. This is due to their advantageous properties, such as low density, high hardness and strength, and excellent high temperature and oxidation resistance. In this study, SiC_f/SiC composites were fabricated via polymer infiltration and pyrolysis (PIP) with the lower–oxygen–content KD–II SiC fiber as the reinforcement; a mixture of 2,4,6,8–tetravinyl–2,4,6,8–tetramethylcyclotetrasiloxane (V4) and liquid polycarbosilane (LPCS), known as LPVCS, was used as the precursor; while pyrolytic carbon (PyC) was used as the interface. The effects of oxidation treatment at different temperatures on morphology, structure, composition, and mechanical properties of the KD–II SiC fibers, SiC matrix from LPVCS precursor conversion, and SiC_f/SiC composites were comprehensively investigated. The results revealed that the oxidation treatment greatly impacted the mechanical properties of the SiC fiber, thereby significantly influencing the mechanical properties of the SiC_f/SiC composite. After oxidation at 1300 °C for 1 h, the strength retention rates of the fiber and composite were 41% and 49%, respectively. In terms of the phase structure, oxidation treatment had little effect on the SiC fiber, while greatly influencing the SiC matrix. A weak peak corresponding to silica (SiO₂) appeared after high–temperature treatment of the fiber; however, oxidation treatment of the matrix led to the appearance of a very strong diffraction peak that corresponds to SiO₂. The analysis of the morphology and composition indicated cracking of the fiber surface after oxidation treatment, which was increasingly obvious with the increase in the oxidation treatment temperature. The elemental composition of the fiber surface changed significantly, with drastically decreased carbon element content and sharply increased oxygen element content.     

Mechanical and dielectric properties of SiCf/BN/SiBCN composites via different synthesis technologies

SiC fibers reinforced SiBCN ceramic matrix composites (SiC_f/BN/SiBCN composites) were synthesized by direct chemical vapor infiltration (CVI), polymer infiltration pyrolysis (PIP) or chemical vapor infiltration combined with polymer infiltration pyrolysis (CVI + PIP). It is shown that the insertion of a continuous and dense SiBCN matrix via the CVI process improves the flexural strength and modulus. Interface debonding and fiber pullout happened with 50–100 nm BN interface in CVI and CVI + PIP SiC_f/BN/SiBCN composites. The relative complex permittivity was measured in X-band. Higher ε′′ values in CVI-containing composites can be observed, which can be attributed to the accumulation of C and SiC phases and a multilayer matrix. Strong electromagnetic wave attenuation ability was obtained with high dielectric loss.     

Effect of intermediate heat treatment on mechanical properties of SiCf/SiC composites with BN interphase prepared by ICVI

SiC_f/SiC composites with BN interface were prepared through isothermal-isobaric chemical vapour infiltration process. Room temperature mechanical properties such as tensile, flexural, inter-laminar shear strength and fracture toughness (K_IC) were studied for the composites. The tensile strength of the SiC_f/SiC composites with stabilised BN interface was almost 3.5 times higher than that of SiC_f/SiC composites with un-stabilised BN interphase. The fracture toughness is similarly enhanced to 23 MPa m^1/2 by stabilisation treatment. Fibre push-through test results showed that the interfacial bond strength between fibre and matrix for the composite with un-stabilised BN interface was too strong (>48 MPa) and it has been modified to a weaker bond (10 MPa) due to intermediate heat treatment. In the case of composite in which BN interface was subjected to thermal treatment soon after the interface coating, the interfacial bond strength between fibre and matrix was relatively stronger (29 MPa) and facilitated limited fibre pull-out.     

Microstructure and damage evolution of SiCf/PyC/SiC and SiCf/BN/SiC mini-composites: A synchrotron X-ray computed microtomography study

SiC_f/PyC/SiC and SiC_f/BN/SiC mini-composites comprising single tow SiC fibre-reinforced SiC with chemical vapor deposited PyC or BN interface layers are fabricated. The microstructure evolutions of the mini-composite samples as the oxidation temperature increases (oxidation at 1000, 1200, 1400, and 1600?°C in air for 2?h) are observed by scanning electron microscopy, energy dispersive spectrometry, and X-ray diffraction characterization methods. The damage evolution for each component of the as-fabricated SiC_f/SiC composites (SiC fibre, PyC/BN interface, SiC matrix, and mesophase) is mapped as a three-dimensional (3D) image and quantified with X-ray computed tomography. The mechanical performance of the composites is investigated via tensile tests.The results reveal that tensile failure occurs after the delamination and fibre pull-out in the SiC_f/PyC/SiC composites due to the volatilization of the PyC interface at high temperatures in the air environment. Meanwhile, the gaps between the fibres and matrix lead to rapid oxidation and crack propagation from the SiC matrix to SiC fibre, resulting in the failure of the SiC_f/PyC/SiC composites as the oxidation temperature increases to 1600?°C. On the other hand, the oxidation products of B₂O₃ molten compounds (reacted from the BN interface) fill up the fracture, cracks, and voids in the SiC matrix, providing excellent strength retention at elevated oxidation temperatures. Moreover, under the protection of B₂O₃, the SiC_f/BN/SiC mini-composites show a nearly intact microstructure of the SiC fibre, a low void growth rate from the matrix to fibre, and inhibition of new void formation and the SiO₂ grain growth from room to high temperatures. This work provides guidance for predicting the service life of SiC_f/PyC/SiC and SiC_f/BN/SiC composite materials, and is fundamental for establishing multiscale damage models on a local scale.     

Synthesis of coatings on SiC fibers and their effects on microstructure and mechanical properties of SiCf/SiBCN composites

In this study, the amorphous C, ZrB₂, and BN single-layer coatings as well as C/BN, C/ZrB₂, ZrB₂/BN, and C/ZrB₂/BN composite coatings were prepared on SiC fibers (SiC_f) by an in situ synthesis and solution impregnation–pyrolysis method. Subsequently, SiC_f/SiBCN composites were fabricated by hot-pressing sintering at 1900℃/60 MPa/30 min to explore the influence of different coatings on the microstructure and mechanical performance of resulting composites. After the preparation of single-layer-coated SiC_f, the SiC_f(BN) or SiC_f(ZrB₂) tended to be overlapped with each other, whereas the dispersion of amorphous C–coated SiC_f was satisfying. Besides, some uneven areas and attached particles have appeared on fiber surfaces of the SiC_f(BN) or SiC_f(ZrB₂), whereas smooth and dense surfaces of amorphous C–coated SiC_f were observed. Because the uniformity of ZrB₂ coatings can be partially damaged by the subsequent coating process of BN, the composite coatings of ZrB₂/BN and C/ZrB₂/BN were thereby not suitable for strengthening SiBCN matrix. The SiC_f/SiBCN composites with C/ZrB₂ coatings have desirable comprehensive mechanical properties. Nevertheless, the conventional toughening mechanisms such as fiber pull-out and bridging, and crack deflection are not available for these composites because the serious crystallization of SiC_f leading to great strength loss, resulting in catastrophic brittle fracture.     

Microstructure and mechanical performance of SiCf/BN/SiC mini-composites oxidized at elevated temperature from ambient temperature to 1500 °C in air

SiC_f/BN/SiC mini-composites comprising single tow SiC fibre-reinforced SiC with chemical vapour deposited (CVD) BN interface layers were fabricated. The mechanical performance and binding strength of the composites and the fibre/interface for the oxidized SiC_f/BN/SiC mini-composite samples (oxidation at 1000, 1200, 1300, 1400 and 1500 °C in air for two hours) were investigated by tensile tests and fibre push-out tests, respectively. The value of oxidation mass change was also measured. Some unusual phenomena for the SiC_f/BN/SiC mini-composites oxidized at 1000 °C were discovered in this work. The tensile strength reached a maximum value, and the mass gain rate showed as a singular negative value, while the shear strength between the fibre and the matrix was moderate. Scanning electron microscopy, energy dispersive spectrometry, infrared spectroscopy and X-ray diffraction characterization methods were used to reveal the microstructural evolution and investigate the unusual phenomenon during oxidation procedures. This work will provide guidance for predicting the service life of SiC_f/BN/SiC composite materials and may enable these materials to become a backbone for thermal structure systems in aerospace applications.     

Synchrotron X-ray tomographic characterization of CVI engineered 2D-woven and 3D-braided SiCf/SiC composites

The properties of ceramic matrix composites strongly depend upon their complex internal structures. To better understand and improve the properties of the silicon carbide fiber-reinforced silicon carbide matrix composites (SiC_f/SiC), we explored the microstructural properties of composites reinforced with either two-dimensional (2D) woven or three-dimensional (3D) braided preforms using synchrotron X-ray computed microtomography. Transects and volumetric images of the composites were reconstructed from objection images and the microstructures were investigated in three spatial directions. The network of void space in a composites was visualized in 3D and quantitative analysis of the porosity was performed to characterize the fiber-tissue structures. 2D-woven SiC_f/SiC composite exhibited important fluctuations of porosity in different directions and the stacking of plies had a significant effect on the porosity distribution. In contrast, 3D-braided SiC_f/SiC composites showed much less variation of porosity. We found the degree of densification of the composite also influenced the porosity distribution.     

Enhancement of the microwave absorption properties of PyC-SiCf/SiC composites by electrophoretic deposition of SiC nanowires on SiC fibers

The employment of coating technique on the silicon carbide fibers plays a pivotal role in preparing SiC fiber-reinforced SiC composites (SiC_f/SiC) toward electromagnetic wave absorption applications. In this work, SiC nanowires (SiCNWs) are successfully deposited onto the pyrolytic carbon (PyC) coated SiC fibers by an electrophoretic deposition method, and subsequently densified by chemical vapor infiltration to obtain SiCNWs/PyC-SiC_f/SiC composites. The results reveal that the introduction of SiCNWs could markedly enhance the microwave absorption properties of PyC-SiC_f/SiC composites. Owing to the increasing of SiCNWs loading, the minimum reflection loss of composites raises up to −58.5 dB in the SiCNWs/PyC-SiC_f/SiC composites with an effective absorption bandwidth (reflection loss ≤ −10 dB) of 6.13 GHz. The remarkable enhancement of electromagnetic wave absorption performances is mainly attributed to the improved dielectric loss ability, impedance matching and multiple reflections. This work provides a novel strategy in preparing SiC_f/SiC composites with excellent electromagnetic wave absorption properties.     

Fabrication and properties of SiCnw-reinforced SiC composites by reactive melt infiltration with BN and PyC interface

To tailor the fiber–matrix interface of SiC nanowires-reinforced SiC (SiC_nw/SiC) ceramic matrix composites (CMCs) for improved mechanical properties, SiC nanowires were coated with BN and pyrolytic carbon (PyC) compound coatings prepared by the dip-coating process in boric acid and urea solution and the pyrolysis of phenolic resin. SiC_nw/SiC CMC with PyC/BN interfaces were fabricated by reactive melt infiltration (RMI) at 1680°C for 1 h. The influences of phenolic resin content on the microstructure and mechanical properties of the CMC were investigated. The results showed that the flexural strength and fracture toughness reach the maximum values of 294 MPa and 4.74 MPa m^1/2 as the phenolic resin content was 16 and 12 wt%, respectively. The displacement–load curve of the sample exhibited a gradient drop with increasing phenolic resin content up to 12 wt%. The results demonstrated that the PyC/BN compound coatings could play the role of protecting the SiC_nw from degradation as well as improving the more moderate interfacial bonding strengths during the RMI.     

Influence of the coupling agent on the mechanical properties of SiCf/poly(phenylene benzobisoxazole) composites

Poly(phenylene benzobisoxazole) (PBO) was first used as matrix to fabricate the two‐dimensional SiC_f/PBO composites by a lamination method. Different amounts of coupling agent were introduced to improve the bonding between silicon carbide (SiC) fibers and the PBO matrix during the fabrication of the SiC_f/PBO composites. The surface structure and composition of the as‐received PBO and PBO treated with the coupling agent were analyzed, and the morphology and flexural strength of the composites were characterized. The Fourier transform infrared analysis indicated that the hydroxyl groups from the coupling agent were successfully introduced to PBO. The flexural strength of the composites increased at first with increasing content of the coupling agent but decreased with excessive addition of the coupling agent. The flexural strength of the composites was improved from 15 to 89 MPa. The test results suggested that the interaction between the SiC fiber and the treated PBO with the coupling agent was intensified. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39805.     

Strengthening/toughening of 2D C/SiC composites by coating

SiC and SiC_w/SiC coatings were prepared on two-dimensional carbon fiber reinforced silicon carbide ceramic matrix composites (2D C/SiC), and strengthening/toughening of the composite by the coatings was investigated. After coating, the density of the C/SiC composites was increased effectively and the mechanical properties were improved significantly. Compared with SiC coating, SiC_w/SiC coating showed the more significant effect on strength/toughness of the composites. Coatings had two effects: surface strengthening and matrix strengthening. The latter was the dominant effect. The surface strengthening can increase the crack initiation stress, while the matrix strengthening can enhance the crack propagation resistance. The former effect increased the strength and the latter effect increased the toughness.     

Oxidation and microstructure of SiCf/SiC composites in moist air up to 1600°C by X-ray tomographic characterization

SiC_f/SiC composites that possess PyC or BN interface layers were fabricated and then oxidized in moist air at 1000, 1200, 1400, and 1600°C. High-resolution CT was used for capturing 3D images and quantifying the SiC phase, mesophase, and voids. The oxidation behavior and microstructural evolution of SiC_f/SiC with PyC or BN interface are discussed in this study. The microstructure of the SiC_f/SiC with a PyC layer was seriously damaged in moist air at high temperature, whereas the BN interface layer enhanced the oxidation resistance of the SiC_f/SiC. These results are also confirmed by using XRD, oxidation mass gain, tensile testing, and SEM measurements. The results of the oxidation behavior and microstructural evolution for SiC_f/SiC oxidized in dry air are also compared with the results of this study. Comparing the SiC_f/SiC with a PyC interface layer, the composite with a BN interface layer oxidized in moist air exhibits a high void growth rate and a low SiO₂ grain growth rate from 1000 to 1600°C. This work will provide guidance for predicting the service life of SiC_f/SiC for multiscale damage rate models of materials at a local scale and will also provide guidance on the life service design of SiC_f/SiC materials.     

In-situ formation of Ti3SiC2 interphase in SiCf/SiC composites by molten salt synthesis

Titanium silicon carbide (Ti₃SiC₂) film was synthesized by molten salt synthesis route of titanium and silicon powder based on polymer-derived SiC fibre substrate. The pre-deposited pyrolytic carbon (PyC) coating on the fibre was utilized as the template and a reactant for Ti₃SiC₂ film. The morphology, microstructure and composition of the film product were characterized. Two Ti₃SiC₂ layers form the whole film, where the Ti₃SiC₂ grains have different features. The synthesis mechanism has been discussed from the thickness of PyC and the batching ratio of mixed powder respectively. Finally, the obtained Ti₃SiC₂ film was utilized as interphase to prepare the SiC fibre reinforced SiC matrix composites (SiC_f/Ti₃SiC₂/SiC composites). The flexural strength (σ_F) and fracture toughness (K_IC) of the SiC_f/Ti₃SiC₂/SiC composite is 460 ± 20 MPa and 16.8 ± 2.4 MPa?m^1/2 respectively.