共查询到17条相似文献,搜索用时 281 毫秒
1.
2.
回转支承的故障监测诊断技术研究 总被引:1,自引:0,他引:1
回转支承的故障监测诊断技术的研究对于提高设备的运行效率、减少经济损失具有重要的意义.有针对性地概述了基于振动信号、温度信号、摩擦力矩、声发射、应力波的回转支承监测诊断技术,以及针对上述信号的分析处理方法,其中包括针对回转支承局部缺陷信号诊断的HHT、EEMD-MSPCA等方法.最后,对各监测诊断方法进行比较,并提出基于... 相似文献
3.
通过对大型回转支承振动信号的分析,提出了基于神经网络的典型故障诊断方法,通过提取故障诊断特征向量,利用三层改进 BP 网络对回转支承若干典型故障进行研究和分析,发现神经网络技术能够有效地解决大型回转支承典型故障的模式识别问题. 相似文献
4.
5.
6.
在介绍了声发射技术的基础上,采用 BP 神经网络,分别对预置故障的港口起重机典型结构———箱型梁的声发射信号进行分析.选用原始波形特征参数以及它们之间组合派生出的特征参数等9个参数作为神经网络的输入,设计箱型梁大应力区常见五种故障模式:正常、局部表面裂纹、局部深埋裂纹、局部焊缝、对接焊缝为最终识别分类模式.结果表明,该方法可以对以上五种模式的声发射源进行有效识别 相似文献
7.
8.
9.
《机械工程与自动化》2016,(1)
系统地阐述了80t/20t固定式起重机的研究和开发,叙述了80t/20t固定式起重机的总体设计和主要部件的设计;通过回转支承的受力分析,对回转支承所受倾覆力矩进行了分析计算。 相似文献
10.
机械方面的故障 起重机的回转支承在回转机构中起着连接上车和底盘部分的作用,又支承着起重机的整个旋转部分。如果回转支承中的钢球损坏、滚道磨损都将影响回转机构的工作,严重时回转机构将出现回转沉重、发出噪声等现象,同时回转液压系统的压力将超过额定值;在停止回转进行起吊和卸荷时,在一起、一落的瞬间,回转支承向下或向上的振动量将过大,说明回转支承的间隙量已严重超标。此时,应对回转支承进行检修或更换。 造成机械故障的大致原因是,维护保养不够和使用不当。 当起重机在有较强腐蚀性和粉尘较多的环境中作业后,或经过较… 相似文献
11.
塔式起重机回转支承主要为焊接结构,因此设计一套适合回转支承结构特点的焊接工装具有重要意义。针对某型塔式起重机回转支承的上、下支座,设计了一套焊接工装模板,并以上支座的筋板焊接工装为例对设计进行了说明。 相似文献
12.
顶升法更换方案是用4只液压同步顶放置在立柱下平台和门座之间的四角位置,将回转支承以上部分顶起,使回转支承与立柱平台、门座分离,拆除、更换回转支承.与采用汽车吊拆除回转支承以上的部分,更换回转支承以后再重新安装的工艺相比,顶升法具有更换成本低、工期短、安全可靠、操作方便等优点. 相似文献
13.
DongSik Gu JaeGu kim YoungSu An ByeongKeun Choi 《Journal of Mechanical Science and Technology》2011,25(5):1279-1286
Vibration analysis is widely used in machinery diagnosis, and wavelet transform and envelope analysis have also been implemented
in many applications to monitor machinery condition. Envelope analysis is well known as a useful tool for the detection of
rolling element bearing faults, and wavelet transform is used in research to detect faults in gearboxes. These are applied
for the development of the condition monitoring system for early detection of the faults generated in several key components
of machinery. Early detection of the faults is a very important factor for condition monitoring and a basic component to extend
CBM (Condition-Based Maintenance) to PM (Prediction Maintenance). The AE (acoustic emission) sensor has a specific characteristic
on the high sensitivity of the signal, high frequency and low energy. Recently, AE technique has been applied in some studies
for the early detection of machine fault. In this paper, a signal processing method for AE signal by envelope analysis with
discrete wavelet transforms is proposed. Through the 15 days test using AE sensor, misalignment and bearing faults were observed
and early fault stage was detected. Also, in order to find the advantage of the proposed signal processing method, the result
was compared to that of the traditional envelope analysis and the accelerometer signal. 相似文献
14.
15.
16.
17.
通过对宝钢原料场11号斗轮取料机回转支承故障进行分析,提出了3排滚柱回转支承替代原球柱联合式回转支承的对策,大大延长了回转支承的使用寿命,确保了现场设备的稳定顺行。 相似文献