Single-cycle resonant converters: a new group of quasi-resonantconverters suitable for high-performance DC/DC and AC/AC conversionapplications

A novel resonant switch and a family of zero-current and zero-voltage mixed-mode switching quasi-resonant converters (QRCs) called single-cycle resonant converters (SCRCs) are proposed to improve the performance of the conventional QRCs. The SCRCs, which include two active switches operated with zero-current switching (ZCS) and zero-voltage switching (ZVS), respectively, show very simple operation and ease of control and analysis, and they overcome the limited load range characteristics of the conventional ZCS QRCs. The SCRCs can be applied even for a high-frequency AC chopper by replacing unidirectional switches with bidirectional ones. Steady-state operation and characteristics of the buck-type SCRCs are analyzed and compared with those of the buck-type full-wave QRC (FW-QRC). Experimental results at a a 200 kHz, 1 kW level are shown to verify the operational principle and characteristics     

Multi-loop control for quasi-resonant converters

A multiloop control scheme for quasi-resonant converters (QRCs) is described. Like current-mode control for pulse width modulation (PWM) converters, this control offers excellent transient response and replaces the voltage-controlled oscillator (VCO) with a simple comparator. In this method, referred to as current-sense frequency modulation (CSFM), a signal proportional to the output-inductor current is compared with an error voltage signal to modulate the switching frequency. The control can be applied to either zero-voltage-switched (ZVS) or zero-current-switched (ZCS) QRCs. Computer simulation is method applied to a ZCS buck QRC. A circuit implementation is presented that allows multiloop control to be used on circuits switching up to 10 MHz. This circuit requires few components and produces clean control waveforms. Experimental results are presented for zero-current flyback and zero-voltage buck QRCs, operating at up to 7 MHz. Good small-signal characteristics have been obtained     

A unified approach to modeling, synthesizing, and analyzingquasi-resonant converters

This paper presents a general method of modeling, synthesizing, and analyzing quasi-resonant converters (QRCs), including actively clamped QRCs. First, the concept of the pulse-width modulation (PWM) switch model is generalized to encompass all PWM (nonisolated) converters. Then, by adding inductor-capacitor (LC) elements and auxiliary switches into the PWM switch, QRC families are synthesized. DC and small signal analyses can be carried out based on these switch models. Furthermore, the duality relationship between zero-voltage-switching (ZVS) and zero-current-switching (ZCS) QRCs is established systematically and rigorously     

A true ZCZVT commutation cell for PWM converters

This paper introduces a true zero-current and zero-voltage transition (ZCZVT) commutation cell for DC-DC pulsewidth modulation (PWM) converters operating with an input voltage less than half the output voltage. It provides zero-current switching (ZCS) and zero-voltage switching (ZVS) simultaneously, at both turn on and turn off of the main switch and ZVS for the main diode. The proposed soft-switching technique is suitable for both minority and majority carrier semiconductor devices and can be implemented in several DC-DC PWM converters. The ZCZVT commutation cell is placed out of the power path, and, therefore, there are no voltage stresses on power semiconductor devices. The commutation cell consists of a few auxiliary devices, rated at low power, and it is only activated during the main switch commutations. The ZCZVT commutation cell, applied to a boost converter, has been analyzed theoretically and verified experimentally. A 1 kW boost converter operating at 40 kHz with an efficiency of 97.9% demonstrates the feasibility of the proposed commutation cell     

Voltage-follower control in zero-current-switched quasi-resonantpower factor preregulators

In this paper, we propose to study the use of several zero-current-switched (ZCS) quasi-resonant converters (QRCs) (buck-boost, flyback, SEPIC, Cuk, boost, and buck) with a half-wave switch, working as power factor preregulators (PFPs) with voltage-follower control. The analysis carried out demonstrates that these converters show excellent characteristics to obtain a high power factor (PF) without using any input-current feedback loop, and they also allow high switching frequency to operate because they integrate transformer and rectifier diode parasitics into the power topology     

Novel zero-Voltage-transition PWM DC-DC converters

A new family of zero-voltage-switching (ZVS) pulsewidth-modulated (PWM) converters that uses a new ZVS-PWM switch cell is presented in this paper. Except for the auxiliary switch, all active and passive semiconductor devices in the ZVS-PWM converters operate at ZVS turn ON and turn OFF. The auxiliary switch operates at zero-current-switching (ZCS) turns ON and OFF. Besides operating at constant frequency, these new converters have no overvoltage across the switches and no additional current stress on the main switch in comparison to the hard-switching converter counterpart. Auxiliary components rated at very small current are used. The principle of operation, theoretical analysis, and experimental results of the new ZVS-PWM boost converter, rated 1 kW, and operating at 80 kHz, are provided in this paper to verify the performance of this new family of converters.     

New family of zero-current-switching PWM converters using a new zero-current-switching PWM auxiliary circuit

A new family of zero-current-switching (ZCS) pulsewidth-modulation (PWM) converters using a new ZCS-PWM auxiliary circuit is presented in this paper. The main switch and auxiliary switch operate at ZCS turn-on and turn-off, and the all-passive semiconductor devices in the ZCS-PWM converters operate at zero-voltage-switching (ZVS) turn-on and turn-off. Besides operating at constant frequency and reducing commutation losses, these new converters have no additional current stress and conduction loss in the main switch in comparison to the hard-switching converter counterpart. The PWM switch model and state-space averaging approach is used to estimate and examine the steady-state and dynamic character of the system. The new family of ZCS-PWM converters is suitable for high-power applications using insulated gate bipolar transistors (IGBTs). The principle of operation, theoretical analysis, and experimental results of the new ZCS-PWM boost converter, rated 1.6 kW and operating at 30 kHz, are provided in this paper to verify the performance of this new family of converters.     

A New Family of Zero-Current-Switching (ZCS) PWM Converters

A new family of zero-current-switching (ZCS) pulsewidth-modulated (PWM) converters which uses a new ZCS-PWM switch cell is presented in this paper. The main switch and auxiliary switch operate at ZCS turn-on and turn-off, and all the passive semiconductor devices in the ZCS-PWM converter operate at zero-voltage-switching (ZVS) turn-on and turn-off. Besides operating at constant frequency and with reduced commutation losses, these new converters have no additional current stress in comparison to the hard-switching converter counterpart. The new family of ZCS-PWM converters is suitable for high-power applications using insulated gate bipolar transistors (IGBTs). The PWM switch model and state-space averaging approach is used to estimate and examine the steady-state and dynamic character of the system. The principle of operation, theoretical analysis, and experimental results of the new ZCS-PWM boost converter, rated 1 kW and operating at 30 kHz, are provided in this paper to verify the performance of this new family of converters.     

Zero-voltage-switching half-bridge DC-DC converter with modified PWM control method

Asymmetric control scheme is an approach to achieve zero-voltage switching (ZVS) for half-bridge isolated dc-dc converters. However, it is not suited for wide range of input voltage due to the uneven voltage and current components stresses. This paper presents a novel "duty-cycle-shifted pulse-width modulated" (DCS PWM) control scheme for half-bridge isolated dc-dc converters to achieve ZVS operation for one of the two switches without causing the asymmetric penalties in the asymmetric control and without adding additional components. Based on the DCS PWM control scheme, an active-clamp branch comprising an auxiliary switch and a diode is added across the isolation transformer primary winding in the half-bridge converter to achieve ZVS for the other main switch by utilizing energy stored in the transformer leakage inductance. Moreover, the auxiliary switch also operates at ZVS and zero-current switching (ZCS) conditions. Furthermore, during the off-time period, the ringing resulted from the oscillation between the transformer leakage inductance and the junction capacitance of two switches is eliminated owing to the active-clamp branch and DCS PWM control scheme. Hence, switching losses and leakage-inductance-related losses are significantly reduced, which provides the converter with the potential to operate at higher efficiencies and higher switching frequencies. The principle of operation and key features of the proposed DCS PWM control scheme and two ZVS half-bridge topologies are illustrated and experimentally verified.     

High-frequency off-line power conversion usingzero-voltage-switching quasi-resonant and multiresonant techniques

The characteristics and limitations of the half-bridge zero-voltage-switched (ZVS) quasi-resonant converters (QRCs) are described. A novel multiresonant concept is proposed for the half-bridge topology to improve the ZVS QRC's load range. Experimental results for 300 V. 75 W zero-voltage-switched quasi-resonant and multiresonant converters operating in the frequency range from 2 MHz to 8 MHz are presented     

Zero-voltage-switched quasi-resonant buck and flybackconverters-experimental results at 10 MHz

Experimental results are presented for buck and flyback zero-voltage-switched (ZVS) quasi-resonant converters (QRCs) operating above 5 MHz. A design procedure for a buck ZVS QRC is proposed that minimizes voltage stress to the power MOSFET transistor while maintaining zero voltage switching for specified ranges of input voltage and load resistance. A quasi-resonant gate drive scheme is also proposed and implemented in a buck converter. The drive is simple and provides high switching speed. Power dissipation in the gate drive is substantially reduced due to the quasi-resonant operation. The ZVS QRC technique described is suitable for very-high-frequency operation due to its ability to reduce dynamic turn-on losses, Miller effect, dv/dt, and di//dt and can be applied in distributed onboard power supplies     

Novel zero-current-switching (ZCS) PWM switch cell minimizingadditional conduction loss

This paper proposes a new zero-current-switching (ZCS) pulsewidth modulation (PWM) switch cell that has no additional conduction loss of the main switch. In this cell, the main switch and the auxiliary switch turn on and turn off under zero-current condition. The diodes commutate softly and the reverse-recovery problems are alleviated. The conduction loss and the current stress of the main switch are minimized, since the resonating current for the soft switching does not flow through the main switch. Based on the proposed ZCS PWM switch cell, a new family of DC-to-DC PWM converters is derived. The new family of ZCS PWM converters is suitable for the high-power applications employing insulated gate bipolar transistors. Among the new family of DC-to-DC PWM converters, a boost converter was taken as an example and has been analyzed. Design guidelines with a design example are described and verified by experimental results from the 2.5 kW prototype boost converter operating at 40 kHz     

An isolated ZVS/ZCS flyback converter using the leakage inductanceof the coupled inductor

This paper describes a simple and effective way to modify an existing hard-switched flyback power converter into a circuit with zero-voltage switching (ZVS) and zero-current switching (ZCS). The key improvement is to turn the unattractive features of the coupled inductor leakage inductance and snubber capacitor into attractive ones. The coupled inductor leakage inductance and snubber are used to form a quasi-resonant circuit to facilitate ZVS/ZCS of all power devices. The operating principles of the power converter and experimental results are presented     

Novel ZVT-PWM converters with active snubbers

An active snubber cell is proposed to contrive zero-voltage-transition (ZVT) pulsewidth-modulated (ZVT-PWM) converters. Except for the auxiliary switch, all active and passive semiconductor devices in a ZVT-PWM converter operate at zero-voltage-switching (ZVS) turn on and turn off. The auxiliary switch operates at ZVS turn off and near zero current-switching (ZCS) turn on. An analytical study on a boost ZVT-PWM converter with the proposed active snubber cell is presented in detail. A 750 W 80 kHz prototype of the boost ZVT-PWM converter has been built in the laboratory to experimentally verify the analysis. Six basic ZVT-PWM converters can be easily created by attaching the proposed active snubber cells to conventional PWM converters. A detailed design procedure of the proposed active snubber cell is also presented in this paper     

一种无源软开关技术的研究

开关电源的高频化使得功率开关的损耗加大,采用软开关技术是减小损耗的有效手段。文中提出了一种采用无源器件构成无损耗吸收回路的结构,可以实现PWM开关电源中开关管的零电流开通和零电压关断,而且不会给开关管带来过大的附加电压应力和电流应力。文中对该电路工作原理和能量转移关系进行了分析,给出了关键参数的选取原则。最后利用saber软件对电路进行了仿真。     

A zero-voltage transition boost converter using a zero-voltage switching auxiliary circuit

A soft switching boost converter with zero-voltage transition (ZVT) main switch using zero-voltage switching (ZVS) auxiliary switches is proposed. Various operating intervals of the converter are presented and analyzed. Design considerations are discussed. A design example with experimental results obtained from a 300-W, 250-kHz, 300-V output DC-DC converter is presented. A modified gating scheme to utilize the auxiliary switch in the main power processing is discussed. A 600-W, 100-kHz, 380 V output, 90-250 V AC, power factor corrected, AC-to-DC, boost converter with the modified gating scheme is presented. Results show that the main switch maintains ZVT while auxiliary switches retain ZVS for the complete specified line and load conditions. Parasitic oscillations existing in the converters proposed in the literature are completely removed.     

Analysis and design-optimization of LCC resonant inverter forhigh-frequency AC distributed power system

The analysis and design of an LCC resonant inverter for a 20 kHz AC distributed power system are presented. Several resonant converter topologies are assessed to determine their suitability for high efficiency power conversion, under resistive and reactive loads. Two LCC-resonant inverter designs were implemented. One with all switches operating with zero voltage switching (ZVS), and another with two switches operating with ZVS and two switches with zero current switching (ZCS). The experimental results are presented along with a performance comparison of the two versions     

A soft-single-switched forward converter with low stresses and two derived structures

This paper proposes a soft-single-switched forward converter with low current and voltage stresses and two derived converters. These converters operate with a nondissipative snubber in ZCS mode at turning on and ZVS mode at turning off. The output voltage is controlled by using PWM technique. It is carried out a detailed study, where operating principles and some simulation and experimental results are presented.     

一种宽输入电压范围软开关电流型DC/DC转换器

针对太阳能光伏及燃料电池等领域电源需要较宽输入电压范围的需求,提出一种通用的具有较宽输入电压范围的软开关电流型DC/DC转换器。该转换器采用了固定频率混合调制设计,可以在所有工作条件下实现半导体器件的软开关工作,并采用电流馈电技术以便适用于低电压高电流的电源。相较于传统转换器,该转换器更为通用,能够实现零电压开关和零电流开关,并且能够在输入电压和负载变化出现较大变化时控制输出电压。实验结果显示,在20-60V输入电压范围内且负载出现变化时,该转换器均表现出良好的性能。     

Zero-Voltage-Transition PWM Converters With Synchronous Rectifier

In this paper, a family of zero-voltage-transition (ZVT) pulsewidth-modulated converters with synchronous rectifier (SR) is introduced. The SR decreases the conduction losses, while it increases the achieved soft switching range. In this family of converters, zero-voltage-switching (ZVS) condition is attained for the main and rectifier switches. Also, zero-current switching is achieved for the auxiliary switch. In addition, the applied ZVS technique can eliminate the reverse recovery losses of the rectifier switch body diode. The ZVT buck converter with SR is analyzed, and the presented experimental results confirm the theoretical analysis.