Activity of oxygen reduction reaction on small amount of amorphous CeOx promoted Pt cathode for fuel cell application

Pt on ceria (CeO_x) particles supported on carbon black (CB) were synthesized using the combined process of hot precipitation and impregnation methods. During 30 cycles of cyclic voltammetry pre-treatment in the potential ranging from −0.2 to 1.3 V (V vs. Ag/AgCl), it was observed that a small amount of CeO_x, which consisted of the interface region between Pt and CeO_x, remained on Pt particles. Other free CeO_x particles were dissolved into H₂SO₄ aqueous solution. To develop the Pt-CeO_x/CB catalyst, the surface chemical states, the net chemical composition, morphology and electrochemical behavior in H₂SO₄ aqueous solution were characterized. Our microanalysis and electrochemical analysis indicate that the active CeO₂ with high specific surface area provides the continuous amorphous cerium oxide (Ce³⁺, Ce⁴⁺) layer with pores on the surface of Pt particles. It is concluded that the amorphous cerium oxide layer on Pt inhibits the oxidation of Pt surface and contributes to enhancement of the activity on Pt cathode. The single cell performance was also improved using the Pt-CeO_x/CB cathode. Based on all data, it is expected that the design based on characterization of the interface between Pt and small amount of amorphous cerium oxide layer could help in preparation of more active Pt catalyst.     

Influence of the Storage Material on the Storage of NOx at Low Temperatures

The NO _x storage performance at low temperature (100–200 °C) has been studied for model NO _x storage catalysts. The catalysts were prepared by sequentially depositing support, metal oxide and platinum on ceramic monoliths. The support material consisted of acidic aluminium silicate, alumina or basic aluminium magnesium oxide, and the added metal oxide was either ceria or barium oxide. The NO _x conversion was evaluated under net-oxidising conditions with transients between lean and rich gas composition and the NO _x storage performance was studied by isothermal adsorption of NO₂ followed by temperature programmed desorption of adsorbed species. The maximum in NO _x storage capacity was observed at 100 °C for all samples studied. The Pt/BaO/Al₂O₃ catalyst stored about twice the amount of NO _x compared with the Pt/Al₂O₃ and Pt/CeO₂/Al₂O₃ samples. The storage capacity increased with increasing basicity of the support material, i.e. Pt/Al₂O₃·SiO₂ < Pt/Al₂O₃ < Pt/Al₂O₃ · MgO. Water did not significantly affect the NO _x storage performance for Pt/Al₂O₃ or Pt/BaO/Al₂O₃.     

Gold nanoparticles on ceria: importance of O vacancies in the activation of gold

Synchrotron-based techniques (high-resolution photoemission, in-situ X-ray absorption spectroscopy, and time-resolved X-ray diffraction) have been used to study the destruction of SO₂ and the water-gas shift (WGS, CO + H₂O → H₂ + CO₂) reaction on a series of gold/ceria systems. The adsorption and chemistry of SO₂ was investigated on Au/CeO₂(111) and AuO _x /CeO₂ surfaces. The heat of adsorption of the molecule on Au nanoparticles supported on stoichiometric CeO₂(111) was 4–7 kcal/mol larger than on Au(111). However, there was negligible dissociation of SO₂ on the Au/CeO₂(111) surfaces. The full decomposition of SO₂ was observed only after introducing O vacancies in the ceria support. AuO _x /CeO₂ surfaces were found to be much less chemically active than Au/CeO₂(111) or Au/CeO_2−x (111) surfaces. In a separate set of experiments, in-situ time-resolved X-ray diffraction and X-ray absorption spectroscopy were used to monitor the behavior of nanostructured {Au + AuO _x }–CeO₂ catalysts under the WGS reaction. At temperatures above 250 °C, a complete AuO _x → Au transformation was observed with high catalytic activity. Photoemission results for the oxidation and reduction of Au nanoparticles supported on rough ceria films or a CeO₂(111) single crystal corroborate that cationic Au^δ+ species cannot be the key sites responsible for the WGS activity at high temperatures. The active sites in {Au + AuO _x }/ceria catalysts should involve pure gold nanoparticles in contact with O vacancies of the oxide.     

Excellent sulfur resistance of Pt/BaO/CeO2 lean NOx trap catalysts

In this work, we investigated the NO_x storage behavior of Pt/BaO/CeO₂ catalysts, especially in the presence of SO₂. High surface area CeO₂ (110 m²/g) with a rod like morphology was synthesized and used as a support. The Pt/BaO/CeO₂ sample demonstrated slightly higher NO_x uptake in the entire temperature range studied compared with Pt/BaO/γ-Al₂O₃. More importantly, this ceria-based catalyst showed higher sulfur tolerance than the alumina-based one. The time of complete NO_x uptake was maintained even after exposing the sample to 3 g/L of SO₂. The same sulfur exposure, on the other hand, eliminated the complete NO_x uptake time on the alumina-based NO_x storage catalysts. TEM images show no evidence of either Pt sintering or BaS phase formation during reductive de-sulfation up to 600 °C on the ceria-based catalyst, while the same process over the alumina-based catalyst resulted in both a significant increase in the average Pt cluster size and the agglomeration of a newly formed BaS phase into large crystallites. XPS results revealed the presence of about five times more residual sulfur after reductive de-sulfation at 600 °C on the alumina-based catalysts in comparison with the ceria-based ones. All of these results strongly support that, besides their superior intrinsic NO_x uptake properties, ceria-based catalysts have (a) much higher sulfur tolerance and (b) excellent resistance against Pt sintering when they are compared to the widely used alumina-based catalysts.     

Low-temperature catalytic combustion of chlorobenzene over MnOx–CeO2 mixed oxide catalysts

MnO_x–CeO₂ mixed oxide catalysts prepared by sol–gel method were tested for the catalytic combustion of chlorobenzene (CB), as a model of chlorinated aromatic volatile organic compounds (CVOCs). MnO_x–CeO₂ catalysts with the different ratio of Mn/Ce + Mn were found to possess high catalytic activity for catalytic combustion of CB, and MnO_x(0.86)–CeO₂ was the most active catalyst, on which the complete combustion temperature (T_90%) of chlorobenzene was 236 °C. The stability of MnO_x–CeO₂ catalysts in the CB combustion was investigated. MnO_x–CeO₂ catalysts with high Mn/Ce + Mn ratios present high stable activity, which is related to their high ability to remove Cl species adsorbed and a large amount of active surface oxygen.     

Interaction of SO2 with CeO2 and Cu/CeO2 catalysts: photoemission, XANES and TPD studies

CeO₂ and Cu/CeO₂ are effective catalysts/sorbents for the removal or destruction of SO₂. Synchrotron‐based high‐resolution photoemission, X‐ray absorption near‐edge spectroscopy (XANES), and temperature‐programmed desorption (TPD) have been employed to study the reaction of SO₂ with pure and reduced CeO₂ powders, ceria films (CeO₂, CeO_2−x, Ce₂O_3+x) and model Cu/CeO₂ catalysts. The results of XANES and photoemission provide evidence that SO₄ was formed upon the adsorption of SO₂ on pure powders or films of CeO₂ at 300 K. The sulfate decomposed in the 390–670 K temperature range with mainly SO₂ and some SO₃ evolving into gas phase. At 670 K, there was still a significant amount of SO₄ present on the CeO₂ substrates. The introduction of O vacancies in the CeO₂ powders or films favored the formation of SO₃ instead of SO₄. Ceria was able to fully dissociate SO₂ to atomic S only if Ce atoms with a low oxidation state were available in the system. When Cu atoms were added to CeO₂ new active sites for the destruction of SO₂ were created improving the catalytic activity of the system. The surface chemistry of SO₂ on the Cu‐promoted CeO₂ was much richer than on pure CeO₂. The behavior of ceria in several catalytic processes (oxidation of SO₂ by O₂, reduction of SO₂ by CO, automobile exhaust converters) is discussed in light of these results. This revised version was published online in July 2006 with corrections to the Cover Date.     

Support modification to improve the sulphur tolerance of Ag/Al2O3 for SCR of NOx with propene under lean-burn conditions

Ag/Al₂O₃ catalysts with 1 wt% SiO₂ or TiO₂ doping in alumina support have been prepared by wet impregnation method and tested for sulphur tolerance during the selective catalytic reduction (SCR) of NO_x using propene under lean conditions. Ag/Al₂O₃ showed 44% NO_x conversion at 623 K, which was drastically reduced to 21% when exposed to 20 ppm SO₂. When Al₂O₃ support in Ag/Al₂O₃ was doped with 1 wt% SiO₂ or TiO₂ the NO_x conversion remained constant in presence of SO₂ showing the improved sulphur tolerance of these catalysts. Subsequent water addition does not induce significant deactivation. On the contrary, a slight promotional effect on the activity of NO conversion to nitrogen is observed after Si and Ti incorporation. FTIR study showed the sulphation of silver and aluminum sites of Ag/Al₂O₃ catalysts resulting in the decrease in the formation of reactive intermediate species such as –NCO, which in turn decreases NO_x conversion to N₂. In the case of Ag/Al₂O₃ doped with SiO₂ or TiO₂, formation of silver sulphate and aluminum sulphate was drastically reduced, which was evident in FTIR resulting in remarkable improvement in the sulphur tolerance of Ag/Al₂O₃ catalyst. These catalysts before and after the reaction have been characterized with various techniques (XRD, BET surface area, transmittance FTIR and pyridine adsorption) for physico-chemical properties.     

Pt-CeO2/C anode catalyst for direct methanol fuel cells

In order to develop a cheaper and durable catalyst for methanol electrooxidation reaction, ceria (CeO₂) as a co-catalytic material with Pt on carbon was investigated with an aim of replacing Ru in PtRu/C which is considered as prominent anode catalyst till date. A series of Pt-CeO₂/C catalysts with various compositions of ceria, viz. 40 wt% Pt-3–12 wt% CeO₂/C and PtRu/C were synthesized by wet impregnation method. Electrocatalytic activities of these catalysts for methanol oxidation were examined by cyclic voltammetry and chronoamperometry techniques and it is found that 40 wt% Pt-9 wt% CeO₂/C catalyst exhibited a better activity and stability than did the unmodified Pt/C catalyst. Hence, we explore the possibility of employing Pt-CeO₂ as an electrocatalyst for methanol oxidation. The physicochemical characterizations of the catalysts were carried out by using Brunauer Emmett Teller (BET) surface area and pore size distribution (PSD) measurements, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM) techniques. A tentative mechanism is proposed for a possible role of ceria as a co-catalyst in Pt/C system for methanol electrooxidation.     

In situ DRIFTS study of the effect of structure (CeO2–La2O3) and surface (Na) modifiers on the catalytic and surface behaviour of Pt/γ-Al2O3 catalyst under simulated exhaust conditions

The nature and relative populations of adsorbed species formed on the surface of un-promoted and sodium-promoted Pt catalysts supported either on bare Al₂O₃ or CeO₂/La₂O₃-modified Al₂O₃, were investigated by in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) under simulated automobile exhaust conditions (CO + NO + C₃H₆ + O₂) at the stoichiometric point. The DRIFT spectra indicate that interaction of the reaction mixture with the Pt/Al₂O₃ catalyst leads mainly to formation of formates and acetates on the support and carbonyl species on partially positively charged Pt atoms (Pt^δ+). Although enrichment of Al₂O₃ with lanthanide elements (CeO₂ and La₂O₃) does not significantly modify the carboxylate species formed on the support, it causes significant modification of the oxidation state of Pt, as indicated by the appearance of a substantial population of carbonyl species on reduced Pt sites (Pt⁰–CO). This modification of the Pt component is enhanced when Na-promotion is used, leading to formation of carbonyl species only on electron enriched Pt (i.e., fully reduced Pt⁰ sites) and to the formation of NCO on these Pt entities (2180 cm⁻¹). The latter are thought to result from enhanced NO dissociation at Na-modified Pt sites. These results correlate well with observed differences in the catalytic performance of the three different systems.     

Effect of Co and Rh promoter on NOx storage and reduction over Pt/BaO/Al2O3 catalyst

Effect of cobalt and rhodium promoter on NO_x storage and reduction (NSR) kinetics was investigated over Pt/BaO/Al₂O₃. Kinetics of 2% cobalt loading over Pt/BaO/Al₂O₃ demonstrated highest NO_x uptake during lean cycle, while reduction efficiency during rich cycle appeared most poor. In contrast to this, rhodium showed suppressing effect of NO_x uptake during lean cycle and demonstrated an enhanced effect for the higher efficiency of NO_x reduction during rich cycle. DRIFT study for NO_x uptake and regeneration confirmed formation of surface BaNO_x from the band at 1300 cm⁻¹ and formation of bulk BaNO_x from the band at 1330 cm⁻¹.     

A Study on the Properties and Mechanisms for NO x Storage Over Pt/BaAl2O4-Al2O3 Catalyst

The NO_x storage catalyst Pt/BaAl₂O₄-Al₂O₃ was prepared by a coprecipitation--impregnation method. For fresh sample, the barium mainly exists as the BaAl₂O₄ phase except for some BaCO₃ phase. The BaAl₂O₄ phase is the primary NO _x storage phase of the sample. EXAFS and TPD were used for investigating the mechanism of NO _x storage. It is found that two kinds of Pt sites are likely to operate. Site 1 is responsible for NO chemisorption and site 2 for oxidizing NO to nitrates and nitrites. When NO adsorbs on the sample below 200 °C, it mainly chemisorbs in the form of molecular states. Such adsorption results in an increase of the coordination magnitude of Pt-O, and a decrease of that of Pt-Pt and Pt-Cl. The coordination distance of Pt-Pt, Pt-Cl and Pt-O also increases. When the adsorption occurs above 200 °C, NO can be easily oxidized by O₂, and stored as nitrites or nitrates at the basic BaAl₂O₄. Site 2 is regenerated quickly. A high adsorption temperature is favorable for nitrate formation.     

Oxygen Storage Behavior of Ceria–Zirconia-Based Catalysts in the Presence of SO2

This paper investigates the effect of the presence of SO₂ in the dynamics of oxygen storage on ceria and ceria–zirconia. The introduction of SO₂ under reaction conditions at T<873 K negatively affects CO conversion under oscillating conditions on all the supports studied, owing to the formation of sulfate species. Deactivation is observed on all supports and activity is recovered only after desorption of SO₂, which occurs at 950<T<1000 K, depending on catalyst composition (Ce/Zr ratio) and treatment atmosphere. The amount of sulfur adsorbed is higher over solid solutions, reaching a maximum with Ce _x Zr_1–x O₂ (0.5<x<0.68). However this does not adversely affect activity compared to ceria. In the presence of Rh and Pd, reactivation is favored under reaction conditions. More generally, it appears that the removal of sulfates is facilitated in reductive atmospheres (both hydrogen and CO) over mixed oxides. No differences are observed following regeneration under oxidizing conditions.     

Catalytic steam reforming of ethane and propane over CeO2-doped Ni/Al2O3 at SOFC temperature: Improvement of resistance toward carbon formation by the redox property of doping CeO2

Ni/Al₂O₃ with the doping of CeO₂ was found to have useful activity to reform ethane and propane with steam under Solid Oxide Fuel Cells (SOFCs) conditions, 700-900 °C. CeO₂-doped Ni/Al₂O₃ with 14% ceria doping content showed the best reforming activity among those with the ceria content between 0 and 20%. The amount of carbon formation decreased with increasing Ce content. However, Ni was easily oxidized when more than 16% of ceria was doped. Compared to conventional Ni/Al₂O₃, 14%CeO₂-doped Ni/Al₂O₃ provides significantly higher reforming reactivity and resistance toward carbon deposition. These enhancements are mainly due to the influence of the redox properties of doped ceria. Regarding the temperature programmed reduction experiments (TPR-1), the redox properties and the oxygen storage capacity (OSC) for the catalysts increased with increasing Ce doping content. In addition, it was also proven in the present work that the redox of these catalysts are reversible, according to the temperature programmed oxidation (TPO) and the second time temperature programmed reduction (TPR-2) results.During the reforming process, in addition to the reactions on Ni surface, the gas-solid reactions between the gaseous components presented in the system (C₂H₆, C₃H₈, C₂H₄, CH₄, CO₂, CO, H₂O, and H₂) and the lattice oxygen (O_x) on ceria surface also take place. The reactions of adsorbed surface hydrocarbons with the lattice oxygen (O_x) on ceria surface (C_nH_m+O_x→nCO+m/2(H₂)+O_x−n) can prevent the formation of carbon species on Ni surface from hydrocarbons decomposition reaction (C_nH_m⇔nC+m/2H₂). Moreover, the formation of carbon via Boudard reaction (2CO⇔CO₂+C) is also reduced by the gas-solid reaction of carbon monoxide (produced from steam reforming) with the lattice oxygen (CO+O_x⇔CO₂+O_x−1).     

Influence of composition of MgAl2O4 supported NiCeO2ZrO2 catalysts on coke formation and catalyst stability for dry reforming of methane

Dry reforming of methane was studied over Ni catalysts supported on γAl₂O₃, CeO₂, ZrO₂ and MgAl₂O₄ (670 °C, 1.5 bar, 16–20 l CH₄ ml_catalyst⁻¹ h⁻¹). It is shown that MgAl₂O₄ supported Ni catalysts promoted with both CeO₂ and ZrO₂ are promising catalysts for dry reforming of methane with carbon dioxide. Within a certain composition range, the simultaneous promotion with CeO₂ and ZrO₂ has great influence on the amount of coke and the catalyst service time. XRD analyses indicate that formation of crystalline Ce_xZr_1−xO₂ mixed oxide phases occurs on double promotion. In particular, incorporation of low amounts of Zr in the CeO₂ fluorite structure provides stable dry reforming catalysis. As shown with TPR, promotion leads to a higher reduced state of Ni. SEM, XRD and TPR analyses demonstrate that highly dispersed, doubly promoted Ni catalysts with a strong metal-support interaction are essential for stable dry reforming and suppression of the formation of carbon filaments.     

NOx adsorption and diesel soot combustion over La2O3 supported catalysts containing K, Rh and Pt

In this work we report results of NOx adsorption and diesel soot combustion on a noble metal promoted K/La₂O₃ catalyst. The fresh-unpromoted solid is a complex mixture of hydroxide and carbonate compounds, but the addition of Rh favors the preferential formation of lanthanum oxycarbonate during the calcination step. K/La₂O₃ adsorbs NOx through the formation of La and K nitrate species when the solid is treated in NO + O₂ between 70 and 490 °C. Nitrates are stable in the same temperature range under helium flow. However, they become unstable at ca. 360 °C when either Rh and/or Pt are present, the effect of Rh being more pronounced. Nitrates decompose under different atmospheres: NO + O₂, He and H₂. The effect of Rh might be to form a thermally unstable complex (Rh–NO⁺) which takes part both in the formation of the nitrates when the catalyst is exposed to NOx and in the nitrates decomposition at higher temperatures. Regarding soot combustion, nitrates react with soot with a temperature of maximun reaction rate of ca. 370 °C, under tight contact conditions. This temperature is not affected by the presence of Rh, which indicates that the stability of nitrates has little effect on their reaction with soot.     

Characterisation by TPR, XRD and NOx Storage Capacity Measurements of the Ageing by Thermal Treatment and SO2 Poisoning of a Pt/Ba/Al NOx-Trap Model Catalyst

The deactivation of a Pt/Ba/Al₂O₃ NO _x -trap model catalyst submitted to SO₂ treatment and/or thermal ageing at 800 °C was studied by H₂ temperature programmed reduction (TPR), X-ray diffraction (XRD) and NO _x storage capacity measurements.The X-ray diffractogram of the fresh sample exhibits peaks characteristic for barium carbonate. Thermal ageing leads to the decomposition of barium carbonate and to the formation of BaAl₂O₄. The TPR profile of the sulphated sample shows the presence of (i) surface aluminium sulphates, (ii) surface barium sulphates, (iii) bulk barium sulphates. The exposure to SO₂ after ageing leads to a small decrease of the surface barium-based sulphates, expected mainly as aluminate barium sulphates. This evolution can be attributed to a sintering of the storage material. TPR experiments also show that thermal treatment at 800 °C after the exposure to SO₂ involves the decomposition of aluminium surface sulphates to give mainly bulk barium sulphates, also pointed out by XRD. Thus, the thermal treatment at 800 °C leads to a stabilization of the sulphates.These results are in accordance with the NO _x storage capacity measurements. On non-sulphated catalysts, the treatment at 800 °C induces to a decrease of the NO _x storage capacity, showing that barium aluminate presents a lower NO _x storage capacity than barium carbonate. Sulphation strongly decreases the NO _x storage capacity of catalysts, whatever the initial thermal treatment, showing that barium sulphates inhibit the NO₂ adsorption. Moreover, the platinum activity for the NO to NO₂ oxidation is lowered by thermal treatments.     

NO x uptake mechanism on Pt/BaO/Al2O3 catalysts

The NO _x adsorption mechanism on Pt/BaO/Al₂O₃ catalysts was investigated by performing NO _x storage/reduction cycles, NO₂ adsorption and NO + O₂ adsorption on 2%Pt/(x)BaO/Al₂O₃ (x = 2, 8, and 20 wt%) catalysts. NO _x uptake profiles on 2%\Pt/20%BaO/Al₂O₃ at 523 K show complete uptake behavior for almost 5 min, and then the NO _x level starts gradually increasing with time and it reaches 75% of the inlet NO _x concentration after 30 min time-on-stream. Although this catalyst shows fairly high NO _x conversion at 523 K, only ~2.4 wt% out of 20 wt% BaO is converted to Ba(NO₃)₂. Adsorption studies by using NO₂ and NO + O₂ suggest two different NO _x adsorption mechanisms. The NO₂ uptake profile on 2%Pt/20%BaO/Al₂O₃ shows the absence of a complete NO _x uptake period at the beginning of adsorption and the overall NO _x uptake is controlled by the gas–solid equilibrium between NO₂ and BaO/Ba(NO₃)₂ phase. When we use NO + O₂, complete initial NO _x uptake occurs and the time it takes to convert ~4% of BaO to Ba(NO₃)₂ is independent of the NO concentration. These NO _x uptake characteristics suggest that the NO + O₂ reaction on the surface of Pt particles produces NO₂ that is subsequently transferred to the neighboring BaO phase by spill over. At the beginning of the NO _x uptake, this spill-over process is very fast and so it is able to provide complete NO _x storage. However, the NO _x uptake by this mechanism slows down as BaO in the vicinity of Pt particles are converted to Ba(NO₃)₂. The formation of Ba(NO₃)₂ around the Pt particles results in the development of a diffusion barrier for NO₂, and increases the probability of NO₂ desorption and consequently, the beginning of NO _x slip. As NO _x uptake by NO₂ spill-over mechanism slows down due to the diffusion barrier formation, the rate and extent of NO₂ uptake are determined by the diffusion rate of nitrate ions into the BaO bulk, which, in turn, is determined by the gas phase NO₂ concentration.     

Enhanced Sulfur Tolerance of Ceria-Promoted NO x Storage Reduction (NSR) Catalysts: Sulfur Uptake, Thermal Regeneration and Reduction with H2(g)

SO _x uptake, thermal regeneration and the reduction of SO _x via H₂(g) over ceria-promoted NSR catalysts were investigated. Sulfur poisoning and desulfation pathways of the complex BaO/Pt/CeO₂/Al₂O₃ NSR system was investigated using a systematic approach where the functional sub-components such as Al₂O₃, CeO₂/Al₂O₃, BaO/Al₂O₃, BaO/CeO₂/Al₂O₃, and BaO/Pt/Al₂O₃ were studied in a comparative fashion. Incorporation of ceria significantly increases the S-uptake of Al₂O₃ and BaO/Al₂O₃ under both moderate and extreme S-poisoning conditions. Under moderate S-poisoning conditions, Pt sites seem to be the critical species for SO _x oxidation and SO _x storage, where BaO/Pt/Al₂O₃ and BaO/Pt/CeO₂/Al₂O₃ catalysts reveal a comparable extent of sulfation. After extreme S-poisoning due to the deactivation of most of the Pt sites, ceria domains are the main SO _x storage sites on the BaO/Pt/CeO₂/Al₂O₃ surface. Thus, under these conditions, BaO/Pt/CeO₂/Al₂O₃ surface stores more sulfur than that of BaO/Pt/Al₂O₃. BaO/Pt/CeO₂/Al₂O₃ reveals a significantly improved thermal regeneration behavior in vacuum with respect to the conventional BaO/Pt/Al₂O₃ catalyst. Ceria promotion remarkably enhances the SO _x reduction with H₂(g).     

Improvement of Pt/ZrO2 by CeO2 for high pressure CH4/CO2 reforming

CH₄/CO₂ reforming over Pt/ZrO₂, Pt/CeO₂ and Pt/ZrO₂ with CeO₂ was investigated at 2 MPa. Pt/ZrO₂, which shows stable activity under 0.1 MPa, and Pt/CeO₂ showed gradual deactivation with time at the high pressure. The deactivation was suppressed drastically on Pt/ZrO₂ with CeO₂ prepared by different impregnation order (co-impregnation of Pt and CeO₂ on ZrO₂, and consecutive impregnation of Pt and CeO₂ on ZrO₂). The amount of coke deposition was found insignificant and similar among all the catalysts (including Pt/ZrO₂ and Pt/CeO₂). Catalytic activity after the reaction for 24 h was in agreement with Pt particle size after the reaction for same period, indicating that the difference of the catalytic stability is mainly dependent on the extent of Pt aggregation through catalyst preparation, H₂ reduction, and the CH₄/CO₂ reforming. Pt aggregation and the amount of coke deposition were least pronounced on (Pt–Ce)/ZrO₂ prepared by impregnation of CeO₂ on Pt/ZrO₂ and the catalyst showed highest stability.