A Distribution‐free Control Chart for the Joint Monitoring of Location and Scale

Traditional statistical process control for variables data often involves the use of a separate mean and a standard deviation chart. Several proposals have been published recently, where a single (combination) chart that is simpler and may have performance advantages, is used. The assumption of normality is crucial for the validity of these charts. In this article, a single distribution‐free Shewhart‐type chart is proposed for monitoring the location and the scale parameters of a continuous distribution when both of these parameters are unknown. The plotting statistic combines two popular nonparametric test statistics: the Wilcoxon rank sum test for location and the Ansari–Bradley test for scale. Being nonparametric, all in‐control properties of the proposed chart remain the same and known for all continuous distributions. Control limits are tabulated for implementation in practice. The in‐control and the out‐of‐control performance properties of the chart are investigated in simulation studies in terms of the mean, the standard deviation, the median, and some percentiles of the run length distribution. The influence of the reference sample size is examined. A numerical example is given for illustration. Summary and conclusions are offered. Copyright © 2011 John Wiley & Sons, Ltd.     

A double generally weighted moving average exceedance control chart

Since the inception of control charts by W. A. Shewhart in the 1920s, they have been increasingly applied in various fields. The recent literature witnessed the development of a number of nonparametric (distribution‐free) charts as they provide a robust and efficient alternative when there is a lack of knowledge about the underlying process distribution. In order to monitor the process location, information regarding the in‐control (IC) process median is typically required. However, in practice, this information might not be available due to various reasons. To this end, a generalized type of nonparametric time‐weighted control chart labeled as the double generally weighted moving average (DGWMA) based on the exceedance statistic (EX) is proposed. The DGWMA‐EX chart includes many of the well‐known existing time‐weighted control charts as special or limiting cases for detecting a shift in the unknown location parameter of a continuous distribution. The DGWMA‐EX chart combines the better shift detection properties of a DGWMA chart with the robust IC performance of a nonparametric chart, by using all the information from the start until the most recent sample to decide if a process is IC or out‐of‐control. An extensive simulation study reveals that the proposed DGWMA‐EX chart, in many cases, outperforms its counterparts.     

Detecting changes in location using distribution‐free control charts with big data

This paper proposes a simple distribution‐free control chart for monitoring shifts in location when the process distribution is continuous but unknown. In particular, we are concerned with big data applications where there are sufficient in‐control data that can be used to specify certain quantiles of interest which, in turn, are used to assess whether the new, incoming data to be monitored are in control. The distribution‐free chart is shown to lose very little power against the Shewhart charts designed for normally distributed data. The proposed charts offer a practical and robust alternative to the classical Shewhart charts which assume normality, particularly when monitoring quantiles and the data distribution is skewed. The effect of the size of the reference sample is examined on the assumption that the quantiles are known. Conclusions and recommendations are offered.     

Dynamic probability control limits for CUSUM charts for monitoring proportions with time-varying sample sizes

We consider the problem of monitoring a proportion with time-varying sample sizes. Control charts are generally designed by assuming a fixed sample size or a priori knowledge of a sample size probability distribution. Sometimes, it is not possible to know, or accurately estimate, a sample size distribution or the distribution may change over time. An improper assumption for the sample size distribution could lead to undesirable performance of the control chart. To handle this problem, we propose the use of dynamic probability control limits (DPCLs) which are determined successively as the sample sizes become known. The method is based on keeping the conditional probability of a false alarm at a predetermined level given that there has not been any earlier false alarm. The control limits dynamically change, and the in-control performance of the chart can be controlled at the desired level for any sequence of sample sizes. The simulation results support this result showing that there is no need for any assumption of a sample size distribution with the use of this proposed approach.     

A New Distribution‐free Control Chart for Joint Monitoring of Unknown Location and Scale Parameters of Continuous Distributions

While the assumption of normality is required for the validity of most of the available control charts for joint monitoring of unknown location and scale parameters, we propose and study a distribution‐free Shewhart‐type chart based on the Cucconi 1 statistic, called the Shewhart‐Cucconi (SC) chart. We also propose a follow‐up diagnostic procedure useful to determine the type of shift the process may have undergone when the chart signals an out‐of‐control process. Control limits for the SC chart are tabulated for some typical nominal in‐control (IC) average run length (ARL) values; a large sample approximation to the control limit is provided which can be useful in practice. Performance of the SC chart is examined in a simulation study on the basis of the ARL, the standard deviation, the median and some percentiles of the run length distribution. Detailed comparisons with a competing distribution‐free chart, known as the Shewhart‐Lepage chart (see Mukherjee and Chakraborti 2 ) show that the SC chart performs just as well or better. The effect of estimation of parameters on the IC performance of the SC chart is studied by examining the influence of the size of the reference (Phase‐I) sample. A numerical example is given for illustration. Summary and conclusions are offered. Copyright © 2013 John Wiley & Sons, Ltd.     

Monitoring type‐2 censored reliability data in multistage processes

In this paper, we propose control charts to monitor the Weibull scale parameter of type‐2 censored reliability data in multistage processes. A cumulative sum control chart and 2 exponentially weighted moving average control charts based on conditional expected values are devised to detect decreases in the mean level of reliability‐related quality characteristic. The proposed control schemes are based on standard smallest extreme value distributions derived from Weibull processes to effectively account for the cascade property, which is the main characteristic of multistage processes. Subsequently, simulation study is conducted to evaluate the performance of the control charts using average run length criterion. Extra quadratic loss, performance comparison index, and relative average run length are also used to compare the detect ability of our proposed monitoring procedures. Moreover, sensitivity analysis is done to study the impact of failure number in the sample size and to investigate the robustness of the proposed monitoring procedures against the shift in the previous stage. Finally, a real case study in a glass bottle–making company is investigated to illustrate the performance of the competing control charts. The results reveal the superiority of the cumulative sum control chart.     

Adaptive charting schemes based on double sequential probability ratio tests

Sequential probability ratio test (SPRT) control charts are shown to be able to detect most shifts in the mean or proportion substantially faster than conventional charts such as CUSUM charts. However, they are limited in applications because of the absence of the upper bound on the sample size and possibly large sample numbers during implementation. The double SPRT (2‐SPRT) control chart, which applies a 2‐SPRT at each sampling point, is proposed in this paper to solve some of the limitations of SPRT charts. Approximate performance measures of the 2‐SPRT control chart are obtained by the backward method with the Gaussian quadrature in a computer program. On the basis of two industrial examples and simulation comparisons, we conclude that the 2‐SPRT chart is competitive in that it is more sensitive and economical for small shifts and has advantages in administration because of fixed sampling points and a proper upper bound on the sample size. Copyright © 2008 John Wiley & Sons, Ltd.     

Reduction of the Effect of Estimation Error on In‐control Performance for Risk‐adjusted Bernoulli CUSUM Chart with Dynamic Probability Control Limits

The in‐control performance of any control chart is highly associated with the accuracy of estimation for the in‐control parameter(s). For the risk‐adjusted Bernoulli cumulative sum (CUSUM) chart with a constant control limit, it had been shown that the estimation error could have a substantial effect on the in‐control performance. In our study, we examine the effect of estimation error on the in‐control performance of the risk‐adjusted Bernoulli CUSUM chart with dynamic probability control limits (DPCLs). Our simulation results show that the in‐control performance of risk‐adjusted Bernoulli CUSUM chart with DPCLs is also affected by the estimation error. The most important factors affecting estimation error are the specified desired in‐control average run length, the Phase I sample size, and the adverse event rate. However, the effect of estimation error is uniformly smaller for the risk‐adjusted Bernoulli CUSUM chart with DPCLs than for the corresponding chart with a constant control limit under various realistic scenarios. In addition, we found a substantial reduction in the mean and variation of the standard deviation of the in‐control run length when DPCLs are used. Therefore, use of DPCLs has yet another advantage when designing a risk‐adjusted Bernoulli CUSUM chart. Copyright © 2016 John Wiley & Sons, Ltd.     

Effects of Parameter Estimation on the Multivariate Distribution‐free Phase II Sign EWMA Chart

Multivariate nonparametric control charts can be very useful in practice and have recently drawn a lot of interest in the literature. Phase II distribution‐free (nonparametric) control charts are used when the parameters of the underlying unknown continuous distribution are unknown and can be estimated from a sufficiently large Phase I reference sample. While a number of recent studies have examined the in‐control (IC) robustness question related to the size of the reference sample for both univariate and multivariate normal theory (parametric) charts, in this paper, we study the effect of parameter estimation on the performance of the multivariate nonparametric sign exponentially weighted moving average (MSEWMA) chart. The in‐control average run‐length (ICARL) robustness and the out‐of‐control shift detection performance are both examined. It is observed that the required amount of the Phase I data can be very (perhaps impractically) high if one wants to use the control limits given for the known parameter case and maintain a nominal ICARL, which can limit the implementation of these useful charts in practice. To remedy this situation, using simulations, we obtain the “corrected for estimation” control limits that achieve a desired nominal ICARL value when parameters are estimated for a given set of Phase I data. The out‐of‐control performance of the MSEWMA chart with the correct control limits is also studied. The use of the corrected control limits with specific amounts of available reference sample is recommended. Otherwise, the performance the MSEWMA chart may be seriously affected under parameter estimation. Copyright © 2016 John Wiley & Sons, Ltd.     

Optimal Design of the Adaptive Sample Size and Sampling Interval np Control Chart

Recent research has shown that the adaptive control charts are quicker than the traditional static charts in detecting process shifts. This paper develops the algorithm for the optimization designs of the adaptive np control charts for monitoring the process fraction non‐conforming p. It includes the variable sample size chart, the variable sampling interval chart, and the variable sample size and sampling interval chart. The performance of the adaptive np charts is measured by the average time to signal under the steady‐state mode, which allows the shift in p to occur at any time, even during the sampling inspection. By studying the performance of the adaptive np charts systematically, it is found that they do improve effectiveness significantly, especially for detecting small or moderate process shifts. Copyright © 2004 John Wiley & Sons, Ltd.     

Nonparametric signed‐rank control charts with variable sampling intervals

Variable sampling interval (VSI) charts have been proposed in the literature for normal theory (parametric) control charts and are known to provide performance enhancements. In the VSI setting, the time between monitored samples is allowed to vary depending on what is observed in the current sample. Nonparametric (distribution‐free) control charts have recently come to play an important role in statistical process control and monitoring. In this paper a nonparametric Shewhart‐type VSI control chart is considered for detecting changes in a specified location parameter. The proposed chart is based on the Wilcoxon signed‐rank statistic and is called the VSI signed‐rank chart. The VSI signed‐rank chart is compared with an existing fixed sampling interval signed‐rank chart, the parametric VSI ‐chart, and the nonparametric VSI sign chart. Results show that the VSI signed‐rank chart often performs favourably and should be used.     

The Negative Binomial Exponentially Weighted Moving Average Chart with Estimated Control Limits

The control chart based on the compound Poisson distribution (the negative binomial exponentially weighted moving average (EWMA) chart) has been shown to be more effective than the c‐chart to monitor the wafer nonconformities in semiconductor production process. The performance of the negative binomial EWMA chart is generally evaluated with the assumption that the process parameters are known. However, in many control chart applications, the process parameters are usually unknown and are required to be estimated. For an accurate parameter estimate, a very large sample size may be required, which is seldom available in the applications. This article investigates the effect of parameter estimation on the run length properties of the negative binomial EWMA charts. Using a Markov chain approach, we show that the performance of the negative binomial EWMA chart is affected when parameters are estimated compared with the known‐parameter case. We also provide recommendations regarding phase I sample sizes, smoothing constant and clustering parameter. The sample size must be quite large for the in‐control chart performance to be close to that for the known‐parameter case. Finally, a wafer process example has been used to highlight the practical implications of estimation error and to offer advice to practitioners when constructing/analysing a phase I sample. Copyright © 2013 John Wiley & Sons, Ltd.     

A Robust Bivariate Control Chart Alternative to the Hotelling's T2 Control Chart

In this paper, we proposed a new bivariate control chart denoted by based on the robust estimation as an alternative to the Hotelling's T² control chart. The location vector and the variance‐covariance matrix for the new control chart are obtained using the sample median, the median absolute deviation from the sample median, and the comedian estimator. The performance of the proposed method in detecting outliers is evaluated and compared with the Hotelling's T² method using a Monte‐Carlo simulation study. A numerical example is considered to illustrate the application of the proposed method. Copyright © 2012 John Wiley & Sons, Ltd.     

An np‐control chart for inspection errors and repeated classifications

The np‐control chart has been used to monitor the conforming fraction in process production, and it is assumed that no classification errors occur during the inspection process. Increases in the sample size and/or the number of repeated classifications of the inspected items can reduce the impact of the classification errors. In this paper, an np ‐control chart is proposed, and the monitored statistics are based on the results of independent repeated classifications with classification errors during the inspection process. The aim of the proposed control chart is to have the same performance as a control chart without classification errors. Numerical examples illustrate the proposal. Copyright © 2011 John Wiley & Sons, Ltd.     

The Max EWMAMS control chart for joint monitoring of process mean and variance with individual observations

A traditional approach to monitor both the location and the scale parameters of a quality characteristic is to use two separate control charts. These schemes have some difficulties in concurrent tracking and interpretation. To overcome these difficulties, some researchers have proposed schemes consisting of only one chart. However, none of these schemes is designed to work with individual observations. In this research, an exponentially weighted moving average (EWMA)‐based control chart that plots only one statistic at a time is proposed to simultaneously monitor the mean and variability with individual observations. The performance of the proposed scheme is compared with one of the two other existing combination charts by simulation. The results show that in general the proposed chart has a significantly better performance than the other combination charts. Copyright © 2010 John Wiley & Sons, Ltd.     

A simple categorical chart for detecting location shifts with ordinal information

Traditional control charts for monitoring attribute data usually neglect the order among the attribute levels, such as good, marginal and bad, of a categorical factor. Such order may be reflected by an underlying continuous variable, which determines the level of the categorical factor by classifying it according to some thresholds in the latent continuous scale. This paper exploits this ordinal information and proposes a control chart for detecting location shifts in the latent variable based on merely the attribute level counts, regardless of the continuous values of the latent variable. The proposed ordinal chart is very simple to construct and enjoys the same setting as conventional categorical charts. Numerical simulations demonstrate the superiority of this simple ordinal categorical chart.     

Robust control charts for percentiles based on location‐scale family of distributions

In this paper, robust control charts for percentiles based on location‐scale family of distributions are proposed. In the construction of control charts for percentiles, when the underlying distribution of the quality measurement is unknown, we study the problem of discriminating different possible candidate distributions in the location‐scale family of distributions and obtain control charts for percentiles which are insensitive to model mis‐specification. Two approaches, namely, the random data‐driven model selection approach and weighted modeling approach, are used to construct the robust control charts for percentiles in order to effectively monitor the manufacturing process. Monte Carlo simulation studies are conducted to evaluate the performance of the proposed robust control charts for various settings with different percentiles, false‐alarm rates, and sample sizes. These proposed procedures are compared in terms of the average run length. The proposed robust control charts are applied to real data sets for the illustration of robustness and usefulness.     

Guidelines for the application of adaptive control charting schemes

A comprehensive performance study and comparison of several adaptive statistical process control procedures is presented. These adaptive control chart procedures are modifications to standard Shewhart control charts that include changing the sampling interval, the sample size or both according to rules based on the value of the sample statistic. Adaptive control techniques are known to improve the performance of the standard Shewhart control charts. In this paper we develop a four-state adaptive sample size control chart and several variations of a three-state combined adaptive sample size and sampling interval control chart. We then compare these new schemes with the previously developed schemes, the two-state adaptive sampling interval, the two-state adaptive sample size and two-state combined adaptive sample size and sampling interval control chart, three-state adaptive sample size control chart and non-adaptive Shewhart control charts. These results show that the addition of the third and fourth states on the adaptive control chart schemes improve the control chart performance; however, the improvement is relatively modest.     

Monitoring compositional data using multivariate exponentially weighted moving average scheme

Recently, the monitoring of compositional data by means of control charts has been investigated in the statistical process control literature. In this article, we develop a Phase II multivariate exponentially weighted moving average control chart, for the continuous surveillance of compositional data based on a transformation into coordinate representation. We use a Markov chain approximation to determine the performance of the proposed multivariate control chart. The optimal multivariate exponentially weighted moving average smoothing constants, control limits, and out‐of‐control average run lengths have been computed for different combinations of the in‐control average run lengths and the number of variables. Several tables are presented and enumerated to show the statistical performance of the proposed control chart. An example illustrates the use of this chart on an industrial problem from a plant in Europe.     

A moving average control chart using a robust scale estimator for process dispersion

Control charts are one of the most powerful tools used to detect and control industrial process deviations in statistical process control. In this paper, a moving average control chart based on a robust scale estimator of standard deviation, namely, the sample median absolute deviation (MAD) statistic, for monitoring process dispersion, is proposed. A simulation study is conducted to evaluate the performance of the proposed moving average median absolute deviation (MA‐MAD) chart, in terms of average run length for various distributions. The results show that the moving average MAD chart performs well in detecting small and moderate shifts in process dispersion, especially when the normality assumption is violated. In addition, this chart is very efficient, especially when the quality characteristic follows a skewed distribution. Numerical and simulated examples are given at the end of the paper.