Ag/BiVO4复合纳米纤维光催化性能的研究

本文采用静电纺丝法制备了不同Ag负载含量的Ag/BiVO₄纳米纤维复合材料,并对其相结构,形貌,可见光催化性能进行了表征。结果表明,Ag的引入能够很大程度的提高复合材料的光催化效率,10%Ag负载的Ag/BiVO₄复合纳米纤维能够在可见光辐照20min内将罗丹明B完全降解。这种异质结够有利于光生电子对的分离,提高光生载流子寿命,是Ag/BiVO₄复合纳米纤维光催化性能显著提高的原因。     

In situ synthesis of Co3O4/graphene nanocomposite material for lithium-ion batteries and supercapacitors with high capacity and supercapacitance

Co₃O₄/graphene nanocomposite material was prepared by an in situ solution-based method under reflux conditions. In this reaction progress, Co²⁺ salts were converted to Co₃O₄ nanoparticles which were simultaneously inserted into the graphene layers, upon the reduction of graphite oxide to graphene. The prepared material consists of uniform Co₃O₄ nanoparticles (15-25 nm), which are well dispersed on the surfaces of graphene nanosheets. This has been confirmed through observations by field emission scanning electron microscopy, transmission electron microscopy and atomic force microscopy. The prepared composite material exhibits an initial reversible lithium storage capacity of 722 mAh g⁻¹ in lithium-ion cells and a specific supercapacitance of 478 F g⁻¹ in 2 M KOH electrolyte for supercapacitors, which were higher than that of the previously reported pure graphene nanosheets and Co₃O₄ nanoparticles. Co₃O₄/graphene nanocomposite material demonstrated an excellent electrochemical performance as an anode material for reversible lithium storage in lithium ion cells and as an electrode material in supercapacitors.     

TiO2-g-C3N4 composite materials for photocatalytic H2 evolution under visible light irradiation

In this investigation, we report the preparation of TiO₂-g-C₃N₄ composite materials with varying the wt.% of g-C₃N₄, the characterization of these materials by various techniques and photocatalytic hydrogen production under visible light irradiation in the presence of methanol. The X-ray powder diffraction (XRD) shows that the composite materials are consist of anatase TiO₂ and g-C₃N₄. Fourier transform infrared (FT-IR) spectra show that the absorbance band intensity of composite materials was stronger than that of C₃N₄. The UV-vis absorption spectra show that the absorption edge of the composite materials shifts to the lower energy region comparing to pure anatase and to longer wavelengths with increasing the amount of C₃N₄. The significant photoluminescence quenching was observed in TiO₂-C₃N₄ composite materials, indicating the charge transfer from C₃N₄ to TiO₂. The visible light induced H₂ evolution rate was remarkably enhanced by coupling TiO₂ with C₃N₄.     

Synthesis, characterization and photocatalytic activity of NaNbO3/ZnO heterojunction photocatalysts

A series of NaNbO₃/ZnO heteronanostructures were synthesized with the hydrothermal method. Various characterization methods such as X-ray powder diffraction (XRD), scanning electronic microscope (SEM) and energy dispersive X-ray spectrometer (EDS), transmission electron microscope (TEM), X-ray photoelectron spectra (XPS) and diffuse reflectance spectra (DRS) were employed to investigate the structure, morphology and photocatalytic properties. The photocatalytic activity of the catalysts was evaluated by the degradation of methylene blue dye and the highest photocatalytic efficiency was observed when the content of NaNbO₃ was 10 wt.%. The photocatalytic mechanism of the heterojunction was also discussed. The effective transformation of the photoexcited electron and holes restricted the recombination of charges, which was regarded as the main reason of the high photocatalytic activity.     

Fe3O4/SiO2/Bi2WO6磁性复合光催化剂的制备及其光催化性能

钨酸铋(Bi₂WO₆),结构最简单的Aurivillius相化合物,是近期受到研究者关注的新型光催化材料。然而,光催化剂粉末在反应介质中难被回收,工业化应用成本较高。本文用三步方法合成了可回收的Fe₃O₄/SiO₂/Bi₂WO₆磁性复合光催化剂,通过溶剂热法合成具有磁性的Fe₃O₄,用溶胶凝胶法在Fe₃O₄表面覆盖SiO₂层,后将磁性颗粒与Bi₂WO₆纳米片相结合。光催化剂的形貌结构及性能通过XRD、SEM、PL、UV-vis进行表征测试。结果表明,直径约500 nm的Fe₃O₄微球附着在边长约500 nm的Bi₂WO₆纳米片的表面,SiO₂在两者之间起到了粘连作用。光催化剂Fe₃O₄/SiO₂/Bi₂WO₆对于罗丹明B的光降解活性较好,且有一定磁性,可以通过外加磁场将其从溶液中分离,有较大的应用潜力。     

固相-水热法制备LiFePO4-Li3V2（PO4）3复合材料及其电化学性能（英文）

分别采用固相-水热法和球磨法制备磷酸亚铁锂-磷酸钒锂复合正极材料(LiFePO4-Li3V2(PO4)3)。电化学性能测试表明,LiFePO4-Li3V2(PO4)3复合正极材料的电化学性能远远高于 LiFePO4和 Li3V2(PO4)3单独作为正极材料的性能,并且以固相-水热法制备的复合材料性能优于以球磨法制得的复合材料。研究发现 LiFePO4-Li3V2(PO4)3复合材料有 4 个氧化还原峰,相当于 LiFePO4 和 Li3V2(PO4)3 氧化还原峰的叠加。采用固相-水热法制备的LiFePO4-Li3V2(PO4)3 复合材料形貌较为规则,且有新相物质产生,这是导致其电化学性能较好的原因。     

Effect of Nd2O3 addition on the surface phase of TiO2 and photocatalytic activity studied by UV Raman spectroscopy

TiO₂ modified with Nd₂O₃ (Nd-TiO₂) nanoparticles were prepared by a co-precipitation method and utilized as the photocatalysts for the degradation of Rhodamine B (RhB). The influence of Nd₂O₃ on the bulk and surface phase, surface area, particle size, and optical response of TiO₂ was investigated by X-ray diffraction (XRD), UV Raman spectroscopy, transmission electron microscopy (TEM), BET, and UV-visible diffuse reflectance spectra. It is found that the crystalline phase and phase composition in the bulk and surface region of Nd-TiO₂ calcined at high temperatures can be tuned by changing the amount of Nd₂O₃. Based on the results from XPS, EDX, XRD, and UV Raman spectra, it is assumed that Nd³⁺ ions do not enter the TiO₂ lattice, but highly disperse onto the Nd-TiO₂ particle surface in the form of Nd₂O₃ crystallites. These crystallites inhibit the agglomeration, growth in crystal size, and anatase-to-rutile phase transformation of TiO₂. In the photocatalytic degradation of RhB reaction, Nd-TiO₂ nanoparticles with higher surface area and wider optical response are more reactive in case of the same surface anatase phase. When the mixed phases of anatase and rutile exist in the surface region of Nd-TiO₂, the synergetic effect over surface area and optical response is the important parameter which determines optimal photocatalytic activity.     

Preparation and characteristics of Fe3O4@YVO4:Eu bifunctional magnetic-luminescent nanocomposites

A facile direct precipitation method has been developed for the synthesis of bifunctional magnetic-luminescent nanocomposites with Fe₃O₄ nanoparticles as the core and YVO₄:Eu³⁺ as the shell. Transmission electron microscopy (TEM) images revealed that the obtained bifunctional nanocomposites had a core-shell structure and a spherical morphology. The average size was ∼150 nm, and the thickness of the shell was ∼15 nm. The X-ray diffraction (XRD) patterns showed that a cubic spinel structure of Fe₃O₄ core and a tetragonal phase of YVO₄ shell were obtained. Fourier transform infrared (FT-IR) spectra confirmed that the YVO₄:Eu³⁺ had been successfully deposited on the surface of Fe₃O₄ nanoparticles. Photoluminescence (PL) spectra indicated that the nanocomposites displayed a strong red characteristic emission of Eu³⁺. Magnetic measurements showed that the obtained bifunctional nanocomposites exhibited superparamagnetic behavior at room temperature. Therefore, the bifunctional nanocomposites are expected to develop many potential applications in biomedical fields.     

Al2O3包覆LiNi0.03Co0.05Mn1.92O4正极材料的制备及其电化学性能

以Al(NO3)3?9H2O为包覆原料,通过燃烧法制备得到LiNi0.03Co0.05Mn1.92O4@Al2O3正极材料。通过X射线衍射(XRD),场发射扫描电子显微镜(FESEM)和透射电镜(TEM)等表征手段对材料的结构和形貌进行分析,并通过恒电流充放电、循环伏安(CV)、交流阻抗(EIS)等测试分析材料的电化学性能。结果表明,Al2O3包覆没有改变LiNi0.03Co0.05Mn1.92O4的尖晶石型结构,包覆层厚度约10.6nm。LiNi0.03Co0.05Mn1.92O4@Al2O3正极材料电化学性能得到了明显改善,1 C和10 C倍率下初始放电比容量分别为119.9 mAh?g-1和106.3 mAh?g-1,充放电循环500次后容量保持率分别为88.4%和78.2%,而未包覆的LiNi0.03Co0.05Mn1.92O4在1 C和10 C倍率下初始放电比容量分别为121.2 mAh?g-1和104.0 mAh?g-1,500次循环后容量保持率分别为84.1%和67.6%。LiNi0.03Co0.05Mn1.92O4@Al2O3活化能为32.92 kJ?mol-1,而未包覆材料的活化能为36.24 kJ?mol-1,包覆有效降低了材料Li+扩散所需克服的能垒,提高了材料的电化学性能。     

Dielectric relaxation behaviors of pure and Pr6O11-doped CaCu3Ti4O12 ceramics in high temperature range

Pure and Pr₆O₁₁-doped CaCu₃Ti₄O₁₂ (CCTO) ceramics were prepared by conventional solid-state reaction method. The compositions and structures were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The influences of Pr-ion concentration on dielectric properties of CCTO were measured in the ranges of 60 Hz-3 MHz and 290-490 K. The third phase of Ca₂CuO₃ was observed from the XRD of CCTO ceramics. From SEM, the grain size was decreased obviously with high valence Pr-ion (mixing valence of Pr³⁺ and Pr⁴⁺) substituting Ca²⁺. The room temperature dielectric constant of Pr-doped CCTO ceramics, sintered at 1323 K, was an order of magnitude lower than the pure CCTO ceramics due to the grain size decreasing and Schottky potential increasing. The dielectric spectra of Pr-doped CCTO were flatter than that of pure CCTO. The loss tangent of Pr-doped CCTO ceramics was less than 0.20 in 2 × 10²-10⁵ Hz region below 440 K. The complex impedance spectra of pure and Pr-doped CCTOs were fitted by ZView. From low to high frequency, three semicircles were observed corresponding to three different conducting regions: electrode interface, grain boundary and grain. By fitting the resistors R and capacitors C, the activation energies of grain boundary and electrode contact were calculated. All doped CCTOs showed higher activation energies of grain boundary and electrode than those of pure CCTO ceramics, which were concordant with the decreasing of dielectric constant after Pr₆O₁₁ doping.     

Fe2O4催化纤维素水热法制备 Fe2O3/ 碳纳米复合材料

目的在较为温和的条件下制备氧化铁/碳纳米复合材料。方法以纳米Fe3O4粉体为催化剂,水热催化纤维素碳化,并借助扫描电镜、透射电镜、X射线光电子能谱仪和X射线衍射仪对碳化产物进行表征分析。结果获得了粒径约为150 nm的枣核形氧化铁/碳纳米复合材料。结论通过相对温和的水热反应,纤维素被碳化形成了壳核结构的纳米产物,Fe3O4催化剂在反应过程中被氧化并成为壳核结构产物的核心。     

Preparation and characteristic of spherical Li3V2(PO4)3

Spherical Li₃V₂(PO₄)₃ was synthesized by using N₂H₄ as reducer. The products were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that single-phase, spherical and well-dispersed Li₃V₂(PO₄)₃ has been successfully synthesized in our experimental process. Electrochemical behaviors have been characterized by charge/discharge measurements. The initial discharge capacities of Li₃V₂(PO₄)₃ were 123 mAh g⁻¹ in the voltage range of 3.0–4.3 V and 132 mAh g⁻¹ in the voltage range of 3.0–4.8 V.     

Low-temperature fabrication of high purity Ti3SiC2

In this study, we fabricated high purity Ti₃SiC₂ ceramic by mechanical alloying (MA) and spark plasma sintering (SPS), and investigated the effect of trace amount of Al on these processes. Our results show that addition of proper amount of Al significantly increases the purity of Ti₃SiC₂ in the MA and subsequent SPS products, and remarkably reduces the sintering temperature for Ti₃SiC₂. Ti₃SiC₂ sintered compact with a purity of 96.5 wt% was obtained by 10 h of MA and subsequent SPS from a starting mixture composed of n(Ti):n(Si):n(Al):n(c) = 3:1:0.2:2 at 850 °C. At 1100 °C, Ti₃SiC₂ with a purity of 99.3 wt% and a relative density of 98.9% was obtained.     

废旧锂离子电池中Li, Fe和V的回收及xLiFePO4-yLi3V2(PO4)3的制备

由于LiFePO_4和Li_3V_2(PO_4)_3材料的特征相近,制备方法类似,提供了一种从废旧LiFePO_4和Li_3V_2(PO_4)_3混合电池中回收Li、Fe和V,再制备xLiFePO_4-yLi_3V_2(PO_4)_3的方法。在空气气氛中600℃热处理1h后,去除粘结剂PVDF使活性物质与集流体分离。调节Li、Fe、V和P摩尔比,球磨、锻烧,配制不同比例的xLiFePO_4-yLi_3V_2(PO_4)_3(x:y=5:1,7:1,9:1)复合电极材料。表征了其形貌、结构和电化学性能,结果表明,回收制备的复合材料将同时具备LiFePO_4和Li_3V_2(PO_4)_3两种材料的电化学性能,能显著改善LiFePO_4的倍率性能。     

Electromagnetic composite films based on polypyrrole hydro-sponge and Fe3O4 ferrofluid

The preparation of free-standing electromagnetic composite films based on conductive polypyrrole (PPy) hydro-sponge and the Fe₃O₄ ferrofluid have been successfully accomplished via self-assembly in the presence of β-cyclodextrin sulfate and under static condition. Transmission electron microscope (TEM), scanning electron microscope (SEM) and X-ray diffraction (XRD) are used to study the morphology of the PPy-Fe₃O₄ composite. Structural characterizations by Fourier transform infrared (FTIR) and thermogravimetric analysis (TGA) have proved the interactions between Fe₃O₄ and PPy chains. As-prepared films possess high electrical conductivity, remarkable magnetic response as well as appropriate flexility. Both the conductivity and magnetization of the composite, the latter in particular, depend strongly on the Fe₃O₄ content and thus can be optimized by adjusting the relative content of Fe₃O₄ in the composite. The combination of both magnetic and conducting activities of the resulting composite makes it be a potential candidate as functional material in electromagnetic devices, such as magnetic-controlled switches.     

La2O3含量对Al2O3/Cu基复合材料组织与性能的影响

以La₂O₃粉、Al粉、CuO粉为反应物原料、纯铜为基体,采用原位合成技术和近熔点铸造法制备颗粒增强Cu基复合材料,研究La₂O₃对Al-CuO体系制备的Cu基复合材料组织及性能的影响。结果表明：添加La₂O₃可获得纳米Al₂O₃颗粒,且弥散分布于Cu基体中,制备的材料组织更加细小、均匀,其材料的电导率及摩擦磨损性能明显提高。当添加0.6%wtLa₂O₃,复合材料的电导率达到90.2%IACS,磨损量达到最小,相比未添加La₂O₃,其导电率提高10.1%,磨损量减小36.6%。     

Luminescent and magnetic properties of YVO4:Ln@Fe3O4 (Ln = Eu or Dy) nanocomposites

A series of core-shell bifunctional magnetic-optical YVO₄:Ln³⁺@Fe₃O₄ (Ln³⁺ = Eu³⁺ or Dy³⁺) nanocomposites have been successfully synthesized via two-step method. The nanocomposites have the advantage of high magnetic responsive and unique luminescence properties. The structure, luminescent and magnetic properties of the nanocomposites were investigated by XRD, TEM, PL and VSM. The maximum emission peaks of the nanocomposites are at 618 nm (doping Eu³⁺), 574 nm (doping Dy³⁺). The special saturation magnetization of the nanocomposites is 54 emu/g. The diameter of the nanocomposites is 400-900 nm.     

Sol-gel synthesis and electrochemical performance of Li4Ti5O12/graphene composite anode for lithium-ion batteries

Li₄Ti₅O₁₂/graphene composite was prepared by a facile sol-gel method. The lattice structure and morphology of the composite were investigated by X-ray diffraction (XRD) and scanning electronic microscopy (SEM). The electrochemical performances of the electrodes have been investigated compared with the pristine Li₄Ti₅O₁₂ synthesized by a similar route. The Li₄Ti₅O₁₂/graphene composite presents a higher capacity and better cycling performance than Li₄Ti₅O₁₂ at the cutoff of 2.5-1.0 V, especially at high current rate. The excellent electrochemical performance of Li₄Ti₅O₁₂/graphene electrode could be attributed to the improvement of electronic conductivity from the graphene sheets. When discharged to 0 V, the Li₄Ti₅O₁₂/graphene composite exhibited a quite high capacity over 274 mAh g⁻¹ below 1.0 V, which was quite beneficial for not only the high energy density but also the safety characteristic of lithium-ion batteries.