Effect of deposition voltage on the microstructure of electrochemically deposited hydrogenated amorphous carbon films

Hydrogenated amorphous carbon (a-C:H) films were deposited on Si substrates by electrolysis in a methanol solution at ambient pressure and a low temperature (50 °C), using various deposition voltages. The influence of deposition voltage on the microstructure of the resulting films was analyzed by visible Raman spectroscopy at 514.5 nm and X-ray photoelectron spectroscopy (XPS). The contents of sp³ bonded carbon in the various films were obtained by the curve fitting technique to the C1s peak in the XPS spectra. The hardness and Young’s modulus of the a-C:H films were determined using a nanoindenter. The Raman characteristics suggest an increase of the ratio of sp³/sp² bonded carbon with increasing deposition voltage. The percentage of sp³-bonded carbon is determined as 33–55% obtained from XPS. Corresponding to the increase of sp³/sp², the hardness and Young’s modulus of the films both increase as the deposition voltage increases from 800 V to 1600 V.     

Characteristics of nitrogen doped diamond-like carbon thin films grown by microwave surface-wave plasma CVD

Nitrogen doped diamond-like carbon (DLC:N) thin films were deposited on p-type silicon (p-Si) and quartz substrates by microwave (MW) surface-wave plasma (SWP) chemical vapor deposition (CVD) at low temperature (< 100 °C). For films deposition, argon (Ar: 200 sccm), acetylene (C₂H₂:10 sccm) and nitrogen (N: 5 sccm) were used as carrier, source and doping gases respectively. DLC:N thin films were deposited at 1000 W microwave power where as gas composition pressures were ranged from 110 Pa to 50 Pa. Analytical methods such as X-ray photoelectron spectroscopy (XPS), UV-visible spectroscopy, FTIR and Raman spectroscopy were employed to investigate the chemical, optical and structural properties of the DLC:N films respectively. The lowest optical gap of the film was found to be 1.6 eV at 50 Pa gas composition pressure.     

Optoelectronic properties of nitrogenated amorphous carbon films synthesized by microwave surface wave plasma chemical vapor deposition system

The n-type nitrogen doped amorphous carbon (a-C:N) thin films have been grown by microwave (MW) surface wave plasma (SWP) chemical vapor deposition (CVD) system on silicon, quartz and ITO substrates at different nitrogen flow rates (1 to 4 sccm). The effects of nitrogen doping on chemical, optical, structural and electrical properties were studied through X-ray photoelectron spectroscopy, Nanopics 2100/NPX200 surface profiler, UV/VIS/NIR spectroscopy, Raman spectroscopy and solar simulator measurements. Argon, acetylene and nitrogen are used as plasma sources. Optical band gap decreased and nitrogen atomic concentration (%) increased with increasing nitrogen flow rate as a dopant. The a-C:N/p-Si based device exhibits photovoltaic behavior under illumination (AM 1.5, 100 mW/cm²), with a maximum open-circuit voltage (V_oc), short-circuit current (J_sc) and fill factor of 4.2 mV, 7.4 μA/cm² and 0.25 respectively.     

Enhanced cycling stability of Ni-MH battery by depositing amorphous carbon film on the Ti1.4V0.6Ni negative electrode

Amorphous carbon (a-C) films with various thicknesses depending on the reaction time are deposited on the surface of Ti_1.4V_0.6Ni alloy electrodes for Ni-MH (nickel-metal hydride) battery by radio frequency plasma enhanced chemical vapor deposition (RF-PECVD). With the increasing deposition time, the Raman spectra show a gradually disordered sp²-bonding change of the films and the changing trend of sp²/sp³ is obtained by X-ray photoelectron spectroscopy. The a-C film of depositing for 30 min with the thickness of 400 nm shows a favorable stability in alkaline electrolyte, the capacity is enhanced by 36.2% after 50 cycles than the bare electrode, and the charge voltage is 80 mV lower than the bare one. The a-C film with high sp²-bonded carbon content effectively reduces the charge transfer resistance, and as a coating layer, the dissolution of V of the alloy is also inhibited. In particular, to get a proper discharge voltage and a stable capacity simultaneously, covering completely and an appropriate thickness of the a-C film are crucial for an expected performance.     

Effect of substrate bias voltage on the properties of diamond-like carbon thin films deposited by microwave surface wave plasma CVD

Diamond-like carbon (DLC) thin films were deposited on silicon and ITO substrates with applying different negative bias voltage by microwave surface wave plasma chemical vapor deposition (MW SWP-CVD) system. The influence of negative bias voltage on optical and structural properties of the DLC film were investigated using X-ray photoelectron spectroscopy, UV/VIS/NIR spectroscopy, Fourier transform infrared spectroscopy and Raman spectroscopy. Optical band gap of the films decreased from 2.4 to 1.7 with increasing negative bias voltage (0 to − 200 V). The absorption peaks of sp³ CH and sp² CH bonding structure were observed in FT-IR spectra, showing that the sp²/sp³ ration increases with increasing negative bias voltage. The analysis of Raman spectra corresponds that the films were DLC in nature.     

Temperature effect on bonding structures of amorphous carbon containing more than 30at.% silicon

Bonding evolution of amorphous carbon incorporated with Si or a-C(Si) in a thermal process has not been studied. Unhydrogenated a-C(Si) films were deposited by magnetron sputtering to undergo two different thermal processes: i) sputter deposition at substrate temperatures from 100 to 500 °C; ii) room temperature deposition followed by annealing at 200 to 1000 °C. The hardness of the films deposited at high temperature exhibits a monotonic decrease whereas the films deposited at room temperature maintained their hardness until 600 °C. X-ray photoelectron spectroscopy and Raman spectroscopy were used to analyze the composition and bonding structures. It was established that the change in the mechanical property is closely related to the atomic bonding structures, their relative fractions and the evolution (conversion from C–C sp³ → CC sp² or CC sp² → C–Si sp³) as well as clustering of sp² structures.     

Nucleation and growth of amorphous carbon film on tungsten-implanted stainless steel substrates

Amorphous carbon (a-C) films were deposited on W-implanted (20 kV, 3 × 10¹⁷ ions cm^− 2) and un-implanted steel substrates by plasma immersion ion implantation and deposition (PIII&D). The W implantation pretreatment changes the surface structure and impacts film nucleation. Consequently, the growth mechanism of the a-C film is altered resulting in different surface morphologies and roughnesses even though the films deposited on the un-implanted steel substrates possess similar a-C structures as revealed by Raman spectroscopy. The structural differences are probed by X-ray photoelectron spectroscopy and X-ray diffraction. Moreover, microstructural observations were carried out by transmission electron microscopy. A model based on the statistical formation theory is proposed to explain the growth of the a-C films on the implanted and un-implanted substrates.     

Optical and microstructural properties of diamond-like carbon films grown by pulsed laser deposition

Diamond-like carbon films have been fabricated using 308 nm excimer laser ablation in vacuum followed by deposition at temperatures between 77 K and 573 K. Optical band gap energies are obtained from UV/optical spectroscopy. Raman spectra and X-ray photoelectron spectra (XPS) show that the sp³/(sp² + sp³) ratio in these films is in excess of 0.7 in films deposited at 77 K and 300 K. This ratio decreases to 0.2 in films deposited at 573 K. It is found that films deposited at cryogenic temperatures consist of a matrix structure assembled from embedded nanometer clusters, while films deposited at 300 K or higher temperature are amorphous and atomically flat. Microstructural features in cryogenic films are discussed in relation to the mechanism of deposition and possible phase transitions during assembly of these films.     

Sp content in ta-C films vs pulse bias width to the substrate: A correlative structural analysis

Tetrahedral amorphous carbon (ta-C) films were studied with and without applying fixed pulse bias and frequency at variable pulse widths in double bent Filtered Cathodic Vacuum Arc (FCVA) system. Both from Raman and X-ray photoelectron spectroscopy (XPS) analyses it has been observed that the ratio of sp³/sp² is maximal at pulse width of 15 µs with fixed pulse bias 3 kV and frequency 200 Hz. Increasing or decreasing pulse width from this threshold value accompanies the decreasing sp³ content in the film. It is also observed that with applying pulse bias width at said frequency and bias voltage G peak position was shifted to lower values and after reaching a minimum at 15 µs G peak position shifted to higher wave numbers. At the 15 µs pulse width, 3 kV bias voltage and 200 Hz frequency we have formed ta-C films with maximum sp³ content. This study clearly suggests that it is possible to tune the ta-C film's most important properties such as percentage of sp³ content, internal stress, and hardness by applying pulse width at particular frequency and bias voltage.     

Influence of the substrate nature on the properties of nanocrystalline diamond films

Nanocrystalline diamond/amorphous carbon (NCD/a-C) nanocomposite films have been deposited by microwave plasma CVD from CH₄/N₂ mixtures on a variety of substrates such as polycrystalline diamond, cubic boron nitride, silicon, titanium nitride, and Ti–6Al–4V. The study aimed to investigate the influence of the chemical nature of the substrate, the surface roughness, and the pretreatment of the substrate on the nucleation, the bulk structure, and the mechanical and tribological properties of the NCD/a-C films. The present paper is especially devoted to the bulk structure of the films. By means of X-ray diffraction (XRD), Raman spectroscopy and X-ray photoelectron spectroscopy (XPS) it is shown that the bulk properties of the films are not affected by the properties of the substrate although these have a strong influence on the nucleation behaviour. XRD measurements show that – irrespective of the substrate used – the films contain diamond nanocrystallites of 3–5 nm diameter. From the Raman spectra it can be inferred that the crystallite/matrix ratio does not vary. The XPS measurements, finally, show that there are no great changes in the sp²/sp³ ratio of the matrix. These findings are discussed in view of possible growth mechanisms of NCD/a-C nanocomposite films.     

Cathodoluminescence and electron field emission of boron-doped a-C:N films

The optical and electrical properties of so-called carbon nitride films (a-C:N) and boron doped so-called carbon nitride films (a-C:N:B) are studied with cathodoluminescence (CL) spectroscopy and electron field emission measurement. The a-C:N films were first deposited on Si by a filtered cathodic arc plasma system, and then boron ions (∼1 × 10¹⁶ cm⁻²) were implanted into the a-C:N films to form a-C:N:B films by a medium current implanter. The structural and morphological properties of a-C:N and a-C:N:B films were then analyzed using secondary ion mass spectrometer, X-ray photoelectron spectroscopy, FT-IR spectra, Raman spectroscopy and atomic force microscopy. The a-C:N film exhibits luminescence of blue light (∼2.67 eV) and red light (∼1.91 eV), and the a-C:N:B film displays luminescence of blue light (∼2.67 eV) in CL spectra measured at 300 K. Furthermore, the incorporated boron atoms change the electron field emission property, which shows a higher turn on field for the a-C:N:B film (3.6 V/μm) than that for the a-C:N film (2.8 V/μm).     

X-ray photoemission spectroscopy of nitrogen-doped UNCD/a-C:H films prepared by pulsed laser deposition

Nitrogen-doped ultrananocrystalline diamond (UNCD)/hydrogenated amorphous carbon (a-C:H) films were deposited by pulsed laser deposition (PLD). Nitrogen contents in the films were controlled by varying a ratio in the inflow amount between nitrogen and hydrogen gases. The film doped with a nitrogen content of 7.9 at.% possessed n-type conduction with an electrical conductivity of 18 Ω^? 1 cm^? 1 at 300 K. X-ray photoemission spectra, which were measured using synchrotron radiation, were decomposed into four component spectra due to sp², sp³ hybridized carbons, C=N and C–N. A full-width at half-maximum of the sp³ peak was 0.91 eV. This small value is specific to UNCD/a-C:H films. The sp²/(sp³ + sp²) value was enhanced from 32 to 40% with an increase in the nitrogen content from 0 to 7.9 at.%. This increment probably originates from the nitrogen incorporation into an a-C:H matrix and grain boundaries of UNCD crystallites. Since an electrical conductivity of a-C:H does not dramatically enhance for this doping amount according to previous reports, we believe that the electrical conductivity enhancement is predominantly due to the nitrogen incorporation into grain boundaries.     

Synthesis of nitrogen incorporated diamond-like carbon thin films using microwave surface-wave plasma CVD

Nitrogenated diamond-like (DLC:N) carbon thin films have been deposited by microwave surface wave plasma chemical vapor deposition on silicon and quartz substrates, using argon gas, camphor dissolved in ethyl alcohol composition and nitrogen as plasma source. The deposited DLC:N films were characterized for their chemical, optical, structural and electrical properties through X-ray photoelectron spectroscopy, UV/VIS/NIR spectroscopy, Raman spectroscopy, atomic force microscope and current–voltage characteristics. Optical band gap decreased (2.7 to 2.4 eV) with increasing Ar gas flow rate. The photovoltaic measurements of DLC:N / p-Si structure show that the open-circuit voltage (V_oc) of 168.8 mV and a short-circuit current density (J_sc) of 8.4 μA/cm² under light illumination (AM 1.5 100 mW/cm²). The energy conversion efficiency and fill factor were found to be 3.4 × 10^{− 4}% and 0.238 respectively.     

Improving the corrosion resistance of a-C:H film by a top a-C:H:Si:O layer

During the deposition of a-C:H film, defects (pinholes or discontinuities) caused by excessive stress will inevitably appear, which will reduce the corrosion resistance of the a-C:H film. In this study, top a-C:H:Si:O layers (thickness of approximately 0.3 μm) on the surface of a-C:H films were deposited on a large scale by PACVD technology using acetylene (C₂H₂) and/or hexamethyldisiloxane (HMDSO) as reactants, to improve the corrosion resistance of a-C:H films while ensuring the appropriate overall hardness of the films. The corrosion behaviors of the films were studied by electrochemical impedance spectroscopy (EIS) and Tafel polarization. We found that the a-C:H/a-C:H:Si:O films possess a lower electrolyte penetration rate due to their stronger capacitance characteristics. In addition, the corrosion current density of the a-C:H/a-C:H:Si:O films (10^?10 A cm^?2) were reduced by 2 orders of magnitude compared to the a-C:H film (10^?8 A cm^?2), and by 3 orders of magnitude compared to 316 stainless steel (10^?7 A cm^?2). The impedance results obtained by EIS were simulated using appropriate equivalent circuits, and the corresponding electrical parameters were used to further verify the electrochemical protection behavior of the top a-C:H:Si:O layer.     

Bonding defects and optical band gaps of DLC films deposited by microwave surface-wave plasma CVD

The effects of CH₄ / C₂H₄ flow ratio and annealing temperature on the defect states and optical properties of diamond-like carbon (DLC) films deposited by novel microwave surface-wave plasma chemical vapour deposition (MW SWP CVD) are studied through UV/VIS/NIR measurements, atomic force microscopy, Raman spectroscopy and electron spin resonance analysis. The optical band gap of DLC has been tailored between a relatively narrow range, 2.65–2.5 eV by manipulating CH₄ / C₂H₄ flow ratio and a wide range, 2.5–0.95 by thermal annealing. The ESR spin density varied between 10¹⁹ to 10¹⁷ spins/cm³ depending on the CH₄ / C₂H₄ flow ratio (1 : 3 to 3 : 1). The defect density increased with increasing annealing temperature. Also, there is a strong dependence of spin density on the optical band gap of the annealed-DLC films, and this dependency has been qualitatively understood from Raman spectra of the films as a result of structural changes due to sp³/sp² carbon bonding network. The surfaces of the films are found to be very smooth and uniform (RMS roughness < 0.5 nm).     

Thermal grafting of organic monolayers on amorphous carbon and silicon (111) surfaces: A comparative study

Thermally-assisted (160 °C) liquid phase grafting of linear alkene molecules has been performed simultaneously on amorphous carbon (a-C) and hydrogen passivated crystalline silicon Si(111):H surfaces. Atomically flat a-C films with a high sp³ average surface hybridization, sp³ / (sp² + sp³) = 0.62, were grown using pulsed laser deposition (PLD). Quantitative analysis of X-ray photoelectron spectroscopy, X-ray reflectometry and spectroscopic ellipsometry data show the immobilization of a densely packed (> 3 × 10¹⁴ cm^? 2) single layer of organic molecules. In contrast with crystalline Si(111):H and other forms of carbon films, no surface preparation is required for the thermal grafting of alkene molecules on PLD amorphous carbon. The molecular grafted a-C surface is stable against ambient oxidation, in contrast with the grafted crystalline silicon surface.     

Carbon spheres generated in ‘dusty plasmas’

The formation of spherical hydrogenated amorphous carbon (a-C:H) particulates generated in a radio frequency plasma enhanced chemical vapour deposition (rf-PECVD) system is reported. These particulates appear as a white powder—no other contaminants appear to be present. electron energy loss spectroscopy (EELS) shows characteristics typical of a-C:H with a reduced plasmon energy due to hydrogen incorporation. Raman spectroscopy however revealed a 1456 cm⁻¹ line which was previously not reported on a-C:H films deposited using similar processes. Infrared (IR) spectroscopy shows that these spheres are mainly partially oxidised, methyl-rich, aliphatic hydrocarbons.     

Novel hybrid facing targets sputtered amorphous carbon overcoat for ultra-high density hard disk media

Amorphous carbon films form a critical protective layer on magnetic hard disk media. A novel in-house configured hybrid facing targets sputtering (HyFTS) utilizing a special magnetron arrangement was used to deposit amorphous carbon (a-C) overcoats. The corrosion inhibition ability and mechanical property were investigated and compared with that of the a-C overcoats deposited by conventional magnetron sputtering (CMS). Studies were done using electrochemical techniques and nano-scratch analysis to determine how corrosion inhibition ability changes at thickness of 2 nm and 5 nm and the scratch resistance of the two types of a-C overcoats, respectively. Electrochemical impedance spectroscopy and potentiodynamic polarization investigations have shown that a-C films deposited by HyFTS have good corrosion resistance even at 2 nm thickness. But at 2 nm, CMS deposited a-C overcoat shows sign of corrosion. Nano-scratch test has also shown improved scratch resistance of the HyFTS deposited a-C. This may be attributed to the better quality film with higher sp³ content deposited by HyFTS as a result of it having a higher amount of ionized species generated.     

Microstructure,optical and electrical properties of sputtered HfTiO high-k gate dielectric thin films

The microstructure, optical and electrical properties of HfTiO high-k gate dielectric thin films deposited on Si substrate and quartz substrate by RF magnetron sputtering have been investigated. Based on analysis from x-ray diffraction (XRD) measurements, it has been found that the as-deposited HfTiO films remain amorphous regardless of the working gas pressure. Meanwhile, combined with characterization of ultraviolet-visible spectroscopy (UV–vis) and spectroscopy ellipsometry (SE), the deposition rate, band gap and optical properties of sputtered HfTiO gate dielectrics were determined. Besides, by means of the characteristic curves of high frequency capacitance–voltage (C–V) and leakage current density–voltage (J–V), the electrical parameters, such as permittivity, total positive charge density, border trap charge density, and leakage current density, have been obtained. The leakage current mechanisms are also discussed. The energy band gap of 3.70 eV, leakage current density of 1.39×10⁻⁵ A/cm² at bias voltage of 2 V, and total positive charge density and border trap charge density of 9.16×10¹¹ cm⁻² and 1.3×10¹¹ cm⁻², respectively render HfTiO thin films deposited at 0.6 Pa, potential high-k gate dielectrics in future CMOS devices.     

Structural investigation of nanocrystalline diamond/amorphous carbon composite films

Nanocrystalline diamond/amorphous carbon (NCD/a-C) composite films have been prepared by microwave plasma chemical vapor deposition (MWCVD) from methane/nitrogen mixtures. The complex nature of the coatings required the application of a variety of complementary analytical techniques in order to elucidate their structure. The crystallinity of the samples was studied by selected-area electron diffraction (SAED). The diffraction patterns revealed the presence of diamond crystallites within the films. From the images taken by transmission electron microscopy (TEM) the crystallite size was determined to be on the order of 3–5 nm. The results were confirmed by X-ray diffraction (XRD) measurements exhibiting broad (111) and (220) peaks of diamond from which the average size of the crystallites was calculated. The grain boundary width is 1–1.5 nm as observed by TEM images which corresponds to a matrix volume fraction of about 40–50%. This correlates very well with the crystalline phase content of about 50% in the films estimated from their density (2.75 g/cm³ as determined by X-ray reflectivity). The bonding structure of the composite films was studied by electron energy loss spectroscopy (EELS) in the region of carbon core level. The spectra were dominated by a peak at 292 eV indicating the diamond nature of the investigated films. In addition, the spectra of NCD/a-C films possessed a shoulder at 284 eV due to the presence of a small sp² bonded fraction. This phase was identified also by X-ray photoelectron spectroscopy (XPS). The sp²/sp³ ratio was on the order of 10% as determined by deconvolution of the C1s XPS peak.